HP G60t-500 notebook Win7 64bit - what is max ram?

Product Name HP G60
Product Number: VD896AV
Serial Number: 2CE94894JX
T6600 @2.2GHz
Graphics: Mobile Intel 4 Series Express Chipset Family
System Board: 3612 09.66
System Bios: F.53

Your link is for a G62t -- I have a G60t. It's not even the same kind of ram. The G62t uses DDR3 and mine uses DDR2.
The reason I'm asking here on the HP forum is so that I can get an official response. In this earler model of the G60t the model was sold as max 4GB but actually could take 8 if the OS supported it. I'm trying to find out if mine is the same.
http://h30434.www3.hp.com/t5/Notebook-Hardware/G60t-maximum-RAM/m-p/184322

Similar Messages

Can a 2008 mac book 4.1 use a ssd? Also what is max RAM upgr?

Can a 2008 mac book 4.1 use a SSD? Also what is max RAM upgrade possible beyond 4GB?

Does it matter on the SATA II or III, for the bus?

Hp pavilion Dv7-4143ea what is max RAM

What is maximum RAM I can install8 or 16?
Can I fit an SSD (1gb)

Hi,
1. Max RAM: It supports up to 8GB:
http://support.hp.com/sg-en/document/c02680687
2. Yes, you can use 1TB SSD. They are very cheap now, only around 40 cents/GB
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

WHAT IS MAX RAM IN THE SYSTEM

i was wondering off hand what is the MAX. RAM that my lenovo 9690 02u ,( 2 slot ram setup ), can handle . i have 2 gigs right now .

you have the 3000 J200 system. The system can support 2 gigs per ram slot, so 2 x 2 gigs = 4 gigs max.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

G4 700mHz What is max RAM? Can I go over 1GB?

I upgraded the RAM to what the factory says is the max - 1 GB. But after installing Tiger the machine is very slow. If I put a 1GB chip in the factory slot will the machine recognize it?
I did do a search for the answer before posting and mainly say references to the 1Ghz machines.

Hey,
I don't believe there are any 1GB RAM modules than will fit in this model of iMac, (144-pin PC133). So 1GB will be the max. (2 x 512mb)
Hope this helps

What is max RAM for 845PE board.

My question is really what is the maximum DIMM slot useage. I am getting a MSI 845PE Max2-FIR board. It looks like I didn't read the fine print. Although there are three DIMM slots, only two can accept a double sided DDR memory , for a maximum total of 4 DIMM banks being used. Is this correct?
So, my three 256MB sticks will be down to only two??
Thanks. The move away from the VIA chip will be worth the inconvience.
)

Yes, only 4 banks at a time meaning no more than 2 double sided sticks.
Upto 2GB in total.

Whats the max RAM that will work in a Wallsteet 250Mhz?

I know Apple says 192mb and I read on Mactracker 512Mb. Are there any restrictions, i.e. the bottom slot? Will it take 1 gig?

Sorry for hijacking this thread, but on the "new" RSS layout of the forums, I cannot find any way to post a new topic ! There is no button or link to do so.
My question is related though. I set up my wife on my old Wallstreet 300Mhz using wireless connection to do email, and I am so used to working on a G5, I forgot how slow a G3 is by comparison. The unit only has 128 OEM Ram on it and I see on ebay 512 upgrades for about $50. My wife was complaining about the loading time of the emails.
I'm wondering if she would see an appreciable speed boost if I upped the memory to the max?
Anyone have any ideas? The wireless connections seems good and solid.
Thanks
Jeff

What is minimum RAM allowed & how can i get tiger or panther on the iMac G3

i have 3 iMac G3 computers, one is running tiger, one is running panther and the other is running jaguar. i would like to find out the amount of RAM needed for each of the 3 systems so that they run smoothly and a tad bit faster than they are going just now. You can see in my model info the models of the iMacs i am using (two slot, one tray). Any help is greatly appreciated.
i know tiger runs good with 512mb RAM (it runs like a charm on my Power Mac G4 anyways) but, i am unsure how much i should buy for the other two models. I ain't even sure what the max RAM allotments for them are (i think 1gb). again help is appreciated.

... but, i am unsure how much i should buy
for the other two models.
If you can afford it & want the fastest response, buy the maximum RAM each can support. It really does make a difference, particularly with older Macs with slower drives. That's because when RAM runs low, the OS "pages out" chunks of memory to the drive & "pages in" other chunks. Since this takes a lot longer with older/slower drives than the latest SATA ones, you see many fewer "spinning beachballs" when launching apps or loading documents, plugins, etc. with enough RAM to hold more of it at once.

I bought macbook pro 17" with lion and installed win7 64bit on it.but i don't have language bar and when i changed my keyboard it doesn't changed?what should i do?

i bought macbook pro 17" with lion and installed win7 64bit on it.but i don't have language bar and when i changed my keyboard it doesn't changed?what should i do?

Are you talking about changing the keyboard layout when you are working in Windows? If so, you need to tell people how you are running it (bootcamp, parallels, other) and whether you have already done stuff like
http://windows.microsoft.com/en-US/windows-vista/The-Language-bar-overview

Changing Win7 64bit to 32 bit on Satellite Pro C660-16N

Hello.
>...Satellite Pro C660-16N - Windows 7 64bit Home Premium preinstalled...
Does anyone know what the best route is to change Win7 64bit to Win7 32bit. Does this model have a 32bit install option on HDD recovery?
Or will it have to be a clean install from a Win7 32bit DVD.
Many thanks.

I presume this notebook is offered with 64bit version only (specification) and there is only one way to install 32 bit OS version you must install it using original Microsoft Win7 32 bit installation disc.
Please note: for OS activation you cannot use product key from the sticker. You must buy new licence for your own installation.
By the way: check also if this notebook model is supported for 32 bit version. You can do this on Toshiba support and download page under http://eu.computers.toshiba-europe.com
If you have more questions you are welcome.

Satellite P300-19P won't display 1,440 x 900 in Win7 64bit.

Does anyone know why my Satellite P300-19P won't display 1,440 x 900 in win7 64bit.
It's highest display is 1360 x 768 which leaves a gap of about 1/2 inch at the top and bottom of my screen.
I had full res on XP but not on Win 7.
The drivers are up to date.
Anybody know why?

Im not quite sure about the difference between Vista and Win 7 ATI catalyst but it could be possible that some options are not present in different Catalyst options.
However, the available display resolution depends on the graphic driver.
I think the gap at the bottom and top o the screen appears due to 1360 x 768 resolution.
Its to small because the native resolution of this 17 TFT is 1440 x 900.
What happens if you would not install the ATI driver but would use the common Win 7 graphic card driver?
I installed Win 7 on my notebook and I didnt install graphic card driver because graphic chip was recognized automatically and all resolutions were available.
Check this.

When printing photos at my hp 1514n the colors are odd + not suitable. using win7 64bit +lat. driver

Hi, I' using a hp 1514n for printing photos. It's attached to my Win7 64bit computer. But the colors are not suitable. Printing is in high quality but the coloras are wrong (i.e. instead of a bule sky I get it turquois).
all patches installaed and also the lastest drivers. What else can I do?
The files are ok, because I get the right colors when printign the files at another hp color laser jet with win7 (32 bit)
Where can I get a suitable icc file?

I'd use the GutenPrint drivers. They're usually better than the drivers that HP ships, anyway, and the latest version of GutenPrint will work with Leopard while the HP drivers for a printer that old will not. The drivers at <http://www.linuxfoundation.org/en/OpenPrinting/MacOSX/hpijs> also explicitly support the DJ960C. Those drivers are usually written by HP employees, are often superior to the drivers HP uses, and, like the GutenPrint drivers, are free.

Itunes 10.5.1 Completly not working in Win7 (64bit)

This has been a total disaster update for me. I am running Win7 (64bit) with all my windows updates current. I went ahead and updated Itunes to 10.5.1.
That was a severe mistake. Itunes crashes every time I start the program. I notice that genius is running right at the start up and I manage to shut it off but it still crashes.
So far I have done the following:
Started Itunes in safe mode----Crashes
Done a complete clean install and reinstall---Crashes
Downgraded to 10.5 clean install---Crashes
Upgraded back up to 10.5.1 started back in safe mode--Crashes.
I have stopped my anti-virus during all installs and starts and it still crashes.
My system is clean of viruses.
No error messages are provided for all the crashes other than "This program has stopped working"
My frustration is awful. I really hope they get this fixed or someone can offer a solution. I am so sorry I ran that upgrade.

After a day 1/2 of frustration and tears I got Itunes 10.5.1 working properly on my Win 7 64bit Home Edition.
I concluded that the profile, lets call it blue99 was in some way corrupted. The reason is that I followed the troubleshooting steps outlined here:
http://support.apple.com/kb/ts1717
Under the heading of Create a New User Account
I went ahead and created a new profile, lets call it B99. Under this new profile, I started up Itunes and sure enough it fired right up, Itunes store came up etc with no crashes. The strange part is that when it started up, the Itunes user agreement came up. In the other profile where Itunes would crash, after I would re-install, I NEVER GOT THE USER AGREEMENT. It would just go through an install, and when it would restart, it would immediately start to crash.
So now I concluded in agreement with the suport article that it was a "user-specific problem"
With this info, I took a gamble. I did not follow the "User specific Troubleshooting" offered in the article.
Instead I followed the directions found here:
http://windows.microsoft.com/en-US/windows-vista/fix-a-corrupted-user-profile
I followed these very carefully. I copied all of my files found under C:\users\Old_Username folder, in this case that would have been the profile blue99. From there I copied the folders in there to the C:\users\New_Username folder in this case B99. The most important rule of thumb is MAKE SURE YOU HAVE FULL ADMINSTRATIVE PERMISSIONS BEFORE YOU START.
I then right clicked on the B99 folder and went to Properties and under the Security tab I gave the profile B99 full permissions. After this I went back to Control Panel and under User accounts I went and turned the B99 profile into full administrator and took the corrupted profile blue99 and switched it too Standard adminstration.
I restarted my computer and logged in under B99, started up Itunes and Yay!! Itunes is up and running. No crashes so far!! When I was running Itunes on the old profile I went ahead and turned off Genius and Home sharing. In this new profile I turned on Genius and it worked with no crashes. But I don't want to push my luck so I turned it off. Itunes has been running with no crashes. This is what worked for me, yeah its convuluted but I was desperate!! I don't even consider this a patch, so much as I cheated to get Itunes running.
If someone has a simpler way to get Itunes 10.5.01 to run, please let me know!!
Please note when I started this I had already reinstalled Itunes on the corrupted profile. I did not install Itunes again on the new profile. I just started it up.

When installing iTunes 10.5 64bit on my win7 64bit computer I get a weird error message.

This all started when one day I plugged in my iPhone 4 to my iTunes 10.4 on my PC (win7 64bit) and I got nothing. I got the connection noise and my phone started charging but it would not show up in iTunes. In My Computer, it sees that I have an iPhone plugged in but shows it as a Camera, not a phone, and I am not able to see anything inside said "camera". At this point I decided to clear everything "Apple" off of my computer and manually install iTunes 10.5. Mid download i came across this error message that I have no clue what it is telling me. After clicking "OK" it then tells me "rolling back session" and then tells me that "Apple Mobile Device failed to start. Verify that you have sufficient privileges to start system services." Since getting this messag I suspected that it was an AMD (apple mobile device) issue. AMD seems to be IMPOSSIBLE to uninstall/delete from my computer... At this point I'm giving up and looking for advice/help on this issue.
Im lead to believe that it is an AMD issue because iTunes 10.4 reads my iPod Shuffle perfectly but wont read my iPhone 4 or a friends iPhone 3g.
Thanks in advance for taking the time to read this!! Any help would be greatly appreciated because I dont want to reformat

Hey donovanjj,
Thanks for the question. Let’s try to recreate your SC Info folder:
iTunes: Missing folder or incorrect permissions may prevent authorization
http://support.apple.com/kb/TS1277
If the above does not resolve your issue, you may want to look over the following resources:
iTunes 11 for Windows: If you have trouble burning a disc
http://support.apple.com/kb/PH12349
iTunes for Windows: Additional troubleshooting tips for burning issues
http://support.apple.com/kb/TS1374
Thanks,
Matt M.

HP COLOR LASERJET CM2320 MFP DO NOT SETUP IT ON THE WIN7 64BIT USİNG IT ON THE NETWORK

my hp color laserjet 2320 mfp is not possible to setup it on the my win7 64bits when ı want use it like network printer.But since 2 weeks ago ı can see it on the network when ı want to install it using orginal hp product sotware.When installing the software is not found by software on the network.Why ı am not able reinstall it again.But so intresting it is possible install it using win7 64bits drivers.İf ı install it by these drivers ı can not use all funtions of the printer.I want use orginal software for installing it on my computer and to use all faciliies.I tried all possibilities for windows part .Delete all drivers from pc,registry part but no solution. ı would like find a solution.ıs it possible any problem windows part if it is. what kind of problem and solution.Please give me a help...

HI DeePure,
Print out the supplies status page, and let me know if all the colors print correctly?
Do you have an extra set of cartridges we can use to troubleshoot with?
Print the supplies status page
Follow these steps to print out the supplies status page from your printer.
On the Printer’s control panel, press the Setup button.
Press the down arrow to highlight Reports , and then press OK .
Press the down arrow to highlight Supplies Status Page , and then press OK .
Figure 1: Supplies Status Page
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"

HP G60t-500 notebook Win7 64bit - what is max ram?

Similar Messages

Maybe you are looking for