HP J9776A 2530-24G Statistics

Hello,
I have some problem with my switch and the statistics.
Im useing firmware: YA.15.13.0005
When I run "show interfaces" the counters are completely still.
If I run "show interface 28" (witch is my uplink port) I get
=================================================
28 1,462,425,418 11,416,371 0 0 off 0
=================================================
I know the switch is working, because I got a few customers on it.
But It seems like the statistics is not working at all.
I used the command "clear statistics 17" before everything stop working.
Its not an option to reboot the switch.
Does anyone have an idé or is this a bug in the firmware?

I'm on the same boat. Did You find any solution?

Similar Messages

C3600 Vlan's convert from IOS V 12.4 to 15.2

Hello,
I need some help to get vlan's to get working again.
I have a c2500 with v12.4 that works with the config above, now with a new c3600 with the smae config but with v15.2 I can't put vlan's working.
I also read about it but I can get it work:
Autonomous AP Will Treat The Sub-interface Tied To Bridge-group1 As The Native Vlan
AnchorWhen using a configuration on an autonomous AP where there is no native VLAN defined, each interface is being dot1q tagged, communication will fail after upgrading to 15.2(2)JA or later. It appears that the configuration is still correct after the upgrade, but the AP sends the untagged frames for bridge-group 1, even though the encapsulation is not defined as native. The autonomous AP will treat the sub-interface tied to bridge-group 1 as the native VLAN, even if it is not defined with the native keyword: "encapsulation dot1 <vlan> native". The VLAN associated with bridge-group 1 must be set to native on the connecting switchport configuration
AnchorThe workaround for this is to configure VLAN 100 as the native VLAN on the connected switchport trunk, even though the encapsulation is not specified as native on the AP.
AnchorIP Routing Enabled By Default
AnchorIP routing is enabled by default in 15.2(2)JB. This default configuration will render ip default-gateway statements inoperable. The workaround is to disable ip routing globally (config t, no ip routing), configure a default route instead of a default-gateway (e.g. config t, ip route 0.0.0.0 0.0.0.0 <default-gateway> ), or disable IP routing using the following cli command:
Current config for:
Cisco IOS Software, C3600 Software (AP3G2-K9W7-M), Version 15.2(4)JB5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 01-May-14 22:04 by prod_rel_team
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.14
encapsulation dot1Q 14
ip address 192.168.14.253 255.255.255.0
ip helper-address 192.168.14.254
no ip route-cache
bridge-group 14
bridge-group 14 spanning-disabled
no bridge-group 14 source-learning
interface GigabitEthernet0.16
encapsulation dot1Q 16
ip address 192.168.16.253 255.255.255.0
ip helper-address 192.168.16.254
no ip route-cache
bridge-group 16
bridge-group 16 spanning-disabled
no bridge-group 16 source-learning
interface GigabitEthernet0.100
encapsulation dot1Q 100
ip address 192.168.100.51 255.255.255.0
no ip route-cache
interface BVI1
ip address 10.0.0.1 255.255.0.0
no ip route-cache
ip default-gateway 192.168.100.254
bridge 1 route ip
my config in my HP SW (I use trunk port 24 to c3600):
J9776A Configuration Editor; Created on release #YA.15.13.0005
; Ver #05:08.63.ff.37.27:81
hostname "HP-2530-24G"
trunk 24 trk1 trunk
trunk 1-2 trk4 lacp
no telnet-server
ip default-gateway 192.168.100.254
vlan 1
name "DEFAULT_VLAN"
no untagged 3-22
untagged 23,25-28,Trk1,Trk4
no ip address
exit
vlan 10
untagged 3-22
tagged 23,Trk1,Trk4
ip address 192.168.10.250 255.255.255.0
ip helper-address 192.168.10.254
exit
vlan 11
tagged Trk1,Trk4
no ip address
voice
exit
vlan 15
tagged Trk1,Trk4
ip address 192.168.15.251 255.255.255.0
exit
vlan 100
tagged 23,Trk1,Trk4
ip address 192.168.100.248 255.255.255.0
exit
management-vlan 100
spanning-tree Trk1 priority 4
spanning-tree Trk4 priority 4
From SW i can't ping vlan 100 or other vlan's
I also debug arp packets and see that the packets arrive to router but don't get out.
Any help ?

Hi,
A couple of comments to your configuration.
On your HP switch, you have the trunk 24 trk1 trunk command configured. I believe that you do not really want that command to be configured. In HP's vocabulary, a trunk is an EtherChannel. With this command, you have essentially configured a static (that is, non-LACP) EtherChannel that contains only a single physical port 24. That does not make sense and I see no reason to do that. I suggest you remove that command from your HP configuration and refer to the port 24 directly instead. If you want to define a trunk port (that is, a port carrying traffic from multiple VLANs) on this HP switch, you simply define the port as tagged or untagged in individual VLANs. There is no equivalent for a switchport mode trunk command on your HP switch.
I do not have hands-on experiences with the C3600 access points but I remember from my experiments with 1200 series access points that IP address must be configured on BVI interfaces only. Even though the 1200 series access points allowed IP addresses to be configured on physical interfaces or on subinterfaces, these IP addresses were somehow inactive - the AP simply did not respond when contacted using them. This would explain your own observations. Therefore, if you want your AP to be reachable in VLAN 14 or 16, you have to create a BVI14 or BVI16 and move the IP settings from the subinterface to the appropriate BVI. If you want your AP to be reachable in VLAN 100, you have to create another bridge-group, say, 20, put your Gi0.100 into the bridge-group 20 and move the IP address from Gi0.100 to BVI20. You cannot currently contact your AP in VLAN1 (BVI1) because your switch does not have an IP address in VLAN1. If it had, you should be able to ping the AP from your switch.
You have configured your AP as if it was a router, assigning IP addresses to Gi0.x subinterfaces along with configuring IP helper addresses. I believe this is a mistake. Your AP is a bridge between a wireless and a wired network but it does not perform any routing functions. Therefore, apart from a BVI for the remote management, this AP should not be assigned any other IP address. In particular, defining a helper address is useless here because of two reasons: First, your AP is not a router and bridges all DHCP requests back and forth between the wired and wireless network; second, the IP address of the DHCP server you have configured is obviously inside the same network and IP space, indicating that the DHCP requests can reach it directly without the need for any helper.
Can you try implementing the suggested changes and telling us if it did make any difference?
Best regards,
Peter

Cannot search file content on Word document with embedded Excel table

Cannot search file content on Word document with embedded Excel table. I have Windows 8.1 64-bit and Office 2010 Professional. Only phrases from within Excel tables are not searchable. I have many Word documents with embedded Excel table.
I use it for my invoices. Those invoices are converted to pdf to be sent via mail. Searching the same phrases in related pdf files Works fine. And yes, folders are indexed, searching service is active......... For example I can find all invoices that have
specific address or name, which is located in word document, but cannot find invoices with specific item name or price, being that information is in embedded Excel table. (not linked, embedded). I thought that is a question for Windows forum, but guys directed
me here on Office forum. To clarify, I do not use Ctrl+F inside some document, but Windows Search in my folders. Probably the same happens in Office 2013.
Thank you.

Hi, I have a lot of Word documents (invoices, offers). Main part of those documents is embedded Excel file because it is easier to do mathematics in Excel than in Word. There are columns with description, unit price, quantity, taxes... Now, I need
to find who bought HP switch 2530-24G last year. I open folder with last year invoices and search "2530". Cannot find any. But if that document was converted to pdf for mail, than I can find that phrase. Windows search does not work for content if the content
is in embedded file.

Statistics Currency Error while posting Sales Order (No: V1453)

Hi Sappers,
I am in process of making a company in SAP ERP SD - IDES, and while posting Sales Order, after I input Sold to Party, PO no, Del Plant and Incoterms and I press ENTER: The error comes up as:
Statistics: The currency from in INR for date 25.11.2011 could not be determined.
Kindly suggest a possible solution.
Thanks
Rahul Tikku

Hi,
Just go to "OBD2", select the Accounts group of your customer and "Double Click" on it, then "Double cliick" on "Sales Data" > Further goto, "Sales" and check if "Currency" field is suppressed. if so then change it to required or optional Entry. save and update you customer master in XD02. Then try your process.
Reagrds
DSR

How oracle decide whetehr to use index or full scan (statistics)

Hi Guys,
Let say i have a index on a column.
The table and index statistics has been gathered. (without histograms).
Let say i perform a select * from table where a=5;
Oracle will perform a full scan.
But from which statistics it will be able to know indeed most of the column = 5? (histograms not used)
After analyzing, we get the below:
Table Statistics :
(NUM_ROWS)
(BLOCKS)
(EMPTY_BLOCKS)
(AVG_SPACE)
(CHAIN_COUNT)
(AVG_ROW_LEN)
Index Statistics :
(BLEVEL)
(LEAF_BLOCKS)
(DISTINCT_KEYS)
(AVG_LEAF_BLOCKS_PER_KEY)
(AVG_DATA_BLOCKS_PER_KEY)
(CLUSTERING_FACTOR)
thanks
Index Column (A)
======
1
1
2
2
5
5
5
5
5
5

I have prepared some explanation and have not noticed that the topic has been marked as answered.
This my sentence is not completely true.
A column "without histograms" means that the column has only one bucket. More correct: even without histograms there are data in dba_tab_histograms which we can consider as one bucket for whole column. In fact these data are retrieved from hist_head$, not from histgrm$ as usual buckets.
Technically there is no any buckets without gathered histograms.
Let's create a table with skewed data distribution.
SQL> create table t as
2 select least(rownum,3) as val, '*' as pad
3    from dual
4 connect by level <= 1000000;
Table created
SQL> create index idx on t(val);
Index created
SQL> select val, count(*)
2    from t
3   group by val;
       VAL   COUNT(*)
         1          1
         2          1
         3     999998So, we have table with very skewed data distribution.
Let's gather statistics without histograms.
SQL> exec dbms_stats.gather_table_stats( user, 'T', estimate_percent => 100, method_opt => 'for all columns size 1', cascade => true);
PL/SQL procedure successfully completed
SQL> select blocks, num_rows from dba_tab_statistics
2   where table_name = 'T';
    BLOCKS   NUM_ROWS
      3106    1000000
SQL> select blevel, leaf_blocks, clustering_factor
2    from dba_ind_statistics t
3   where table_name = 'T'
4     and index_name = 'IDX';
    BLEVEL LEAF_BLOCKS CLUSTERING_FACTOR
         2        4017              3107
SQL> select column_name,
2         num_distinct,
3         density,
4         num_nulls,
5         low_value,
6         high_value
7    from dba_tab_col_statistics
8   where table_name = 'T'
9     and column_name = 'VAL';
COLUMN_NAME NUM_DISTINCT    DENSITY NUM_NULLS      LOW_VALUE      HIGH_VALUE
VAL                     3 0,33333333          0           C102            C104So, Oracle suggests that values between 1 and 3 (raw C102 and C104) are distributed uniform and the density of the distribution is 0.33.
Let's try to explain plan
SQL> explain plan for
2 select --+ no_cpu_costing
3         *
4    from t
5   where val = 1
6 ;
Explained
SQL> @plan
| Id | Operation         | Name | Rows | Cost |
|   0 | SELECT STATEMENT |      |   333K|   300 |
|* 1 | TABLE ACCESS FULL| T    |   333K|   300 |
Predicate Information (identified by operation id):
   1 - filter("VAL"=1)
Note
   - cpu costing is off (consider enabling it)Below is an excerpt from trace 10053
BASE STATISTICAL INFORMATION
Table Stats::
Table: T Alias: T
    #Rows: 1000000 #Blks: 3106 AvgRowLen: 5.00
Index Stats::
Index: IDX Col#: 1
    LVLS: 2 #LB: 4017 #DK: 3 LB/K: 1339.00 DB/K: 1035.00 CLUF: 3107.00
SINGLE TABLE ACCESS PATH
BEGIN Single Table Cardinality Estimation
Column (#1): VAL(NUMBER)
    AvgLen: 3.00 NDV: 3 Nulls: 0 Density: 0.33333 Min: 1 Max: 3
Table: T Alias: T
    Card: Original: 1000000 Rounded: 333333 Computed: 333333.33 Non Adjusted: 333333.33
END   Single Table Cardinality Estimation
Access Path: TableScan
    Cost: 300.00 Resp: 300.00 Degree: 0
      Cost_io: 300.00 Cost_cpu: 0
      Resp_io: 300.00 Resp_cpu: 0
Access Path: index (AllEqRange)
    Index: IDX
    resc_io: 2377.00 resc_cpu: 0
    ix_sel: 0.33333 ix_sel_with_filters: 0.33333
    Cost: 2377.00 Resp: 2377.00 Degree: 1
Best:: AccessPath: TableScan
         Cost: 300.00 Degree: 1 Resp: 300.00 Card: 333333.33 Bytes: 0Cost of FTS here is 300 and cost of Index Range Scan here is 2377.
I have disabled cpu costing, so selectivity does not affect the cost of FTS.
cost of Index Range Scan is calculated as
blevel + (leaf_blocks * selectivity + clustering_factor * selecivity) = 2 + (4017*0.33333 + 3107*0.33333) = 2377.
Oracle considers that it has to read 2 root/branch blocks of the index, 1339 leaf blocks of the index and 1036 blocks of the table.
Pay attention that selectivity is the major component of the cost of the Index Range Scan.
Let's try to gather histograms:
SQL> exec dbms_stats.gather_table_stats( user, 'T', estimate_percent => 100, method_opt => 'for columns val size 3', cascade => true);
PL/SQL procedure successfully completedIf you look at dba_tab_histograms you will see following
SQL> select endpoint_value,
2         endpoint_number
3    from dba_tab_histograms
4   where table_name = 'T'
5     and column_name = 'VAL'
6 ;
ENDPOINT_VALUE ENDPOINT_NUMBER
             1               1
             2               2
             3         1000000ENDPOINT_VALUE is the column value (in number for any type of data) and ENDPOINT_NUMBER is cumulative number of rows.
Number of rows for any ENDPOINT_VALUE = ENDPOINT_NUMBER for this ENDPOINT_VALUE - ENDPOINT_NUMBER for the previous ENDPOINT_VALUE.
explain plan and 10053 trace of the same query:
| Id | Operation                   | Name | Rows | Cost |
|   0 | SELECT STATEMENT            |      |     1 |     4 |
|   1 | TABLE ACCESS BY INDEX ROWID| T    |     1 |     4 |
|* 2 |   INDEX RANGE SCAN          | IDX |     1 |     3 |
Predicate Information (identified by operation id):
   2 - access("VAL"=1)
Note
   - cpu costing is off (consider enabling it)
BASE STATISTICAL INFORMATION
Table Stats::
Table: T Alias: T
    #Rows: 1000000 #Blks: 3106 AvgRowLen: 5.00
Index Stats::
Index: IDX Col#: 1
    LVLS: 2 #LB: 4017 #DK: 3 LB/K: 1339.00 DB/K: 1035.00 CLUF: 3107.00
SINGLE TABLE ACCESS PATH
BEGIN Single Table Cardinality Estimation
Column (#1): VAL(NUMBER)
    AvgLen: 3.00 NDV: 3 Nulls: 0 Density: 5.0000e-07 Min: 1 Max: 3
    Histogram: Freq #Bkts: 3 UncompBkts: 1000000 EndPtVals: 3
Table: T Alias: T
    Card: Original: 1000000 Rounded: 1 Computed: 1.00 Non Adjusted: 1.00
END   Single Table Cardinality Estimation
Access Path: TableScan
    Cost: 300.00 Resp: 300.00 Degree: 0
      Cost_io: 300.00 Cost_cpu: 0
      Resp_io: 300.00 Resp_cpu: 0
Access Path: index (AllEqRange)
    Index: IDX
    resc_io: 4.00 resc_cpu: 0
    ix_sel: 1.0000e-06 ix_sel_with_filters: 1.0000e-06
    Cost: 4.00 Resp: 4.00 Degree: 1
Best:: AccessPath: IndexRange Index: IDX
         Cost: 4.00 Degree: 1 Resp: 4.00 Card: 1.00 Bytes: 0Pay attention on selectivity, ix_sel: 1.0000e-06
Cost of the FTS is still the same = 300,
but cost of the Index Range Scan is 4 now: 2 root/branch blocks + 1 leaf block + 1 table block.
Thus, conclusion: histograms allows to calculate selectivity more accurate. The aim is to have more efficient execution plans.
Alexander Anokhin
http://alexanderanokhin.wordpress.com/

Forms 6.0 - how to have forms utilization statistics?

I would like to know how i can retrieve statistics of form utilization during one period without recompile any form. I wanna know for instance the 20 forms more used on a Oracle Forms 6.0 app. Is it possible?
thanks
Luis Reis

Frank
thanks for your answer but the problem is that one . I have 800 forms and we have no time to open all them and make this script ( I am a CIO and not a tech guy so I presume that you are saying that we must write code in the Form, no?)
Luis Reis

Upload data from excel to Ztable with statistics

Hi,
I have a requirement to upload data from excel sheet to ztable .
Here i need tp provide the user with the execution statistics like
1.Number of records read from the Excel spread-sheet
2. Number records processed successfully
3. Number records with Error
4. Name and location of Error Log-file (text-file format)
5. Name and location of the file containing error records (Excel spread-sheet format)
I would appreciate if any of you have code written for the same

See the below example code to upload from xl file to sap
REPORT ZLWMI151_UPLOAD no standard page heading
                       line-size 100 line-count 60.
*tables : zbatch_cross_ref.
data : begin of t_text occurs 0,
       werks(4) type c,
       cmatnr(15) type c,
       srlno(12) type n,
       matnr(7) type n,
       charg(10) type n,
       end of t_text.
data: begin of t_zbatch occurs 0,
      werks like zbatch_cross_ref-werks,
      cmatnr like zbatch_cross_ref-cmatnr,
      srlno like zbatch_cross_ref-srlno,
      matnr like zbatch_cross_ref-matnr,
      charg like zbatch_cross_ref-charg,
      end of t_zbatch.
data : g_repid like sy-repid,
       g_line like sy-index,
       g_line1 like sy-index,
       $v_start_col         type i value '1',
       $v_start_row         type i value '2',
       $v_end_col           type i value '256',
       $v_end_row           type i value '65536',
       gd_currentrow type i.
data: itab like alsmex_tabline occurs 0 with header line.
data : t_final like zbatch_cross_ref occurs 0 with header line.
selection-screen : begin of block blk with frame title text.
parameters : p_file like rlgrap-filename obligatory.
selection-screen : end of block blk.
initialization.
g_repid = sy-repid.
at selection-screen on value-request for p_file.
CALL FUNCTION 'F4_FILENAME'
       EXPORTING
            PROGRAM_NAME = g_repid
       IMPORTING
            FILE_NAME    = p_file.
start-of-selection.
Uploading the data into Internal Table
perform upload_data.
perform modify_table.
top-of-page.
CALL FUNCTION 'Z_HEADER'
EXPORTING
    FLEX_TEXT1       =
    FLEX_TEXT2       =
    FLEX_TEXT3       =
*&      Form upload_data
      text
FORM upload_data.
CALL FUNCTION 'ALSM_EXCEL_TO_INTERNAL_TABLE'
       EXPORTING
            FILENAME                = p_file
            I_BEGIN_COL             = $v_start_col
            I_BEGIN_ROW             = $v_start_row
            I_END_COL               = $v_end_col
            I_END_ROW               = $v_end_row
       TABLES
            INTERN                  = itab
       EXCEPTIONS
            INCONSISTENT_PARAMETERS = 1
            UPLOAD_OLE              = 2
            OTHERS                  = 3.
IF SY-SUBRC <> 0.
    write:/10 'File '.
ENDIF.
if sy-subrc eq 0.
    read table itab index 1.
    gd_currentrow = itab-row.
    loop at itab.
      if itab-row ne gd_currentrow.
        append t_text.
        clear t_text.
        gd_currentrow = itab-row.
      endif.
      case itab-col.
        when '0001'.
          t_text-werks = itab-value.
        when '0002'.
          t_text-cmatnr = itab-value.
        when '0003'.
          t_text-srlno = itab-value.
        when '0004'.
          t_text-matnr = itab-value.
        when '0005'.
          t_text-charg = itab-value.
      endcase.
    endloop.
endif.
append t_text.
ENDFORM.                    " upload_data
*&      Form modify_table
      Modify the table ZBATCH_CROSS_REF
FORM modify_table.
loop at t_text.
    t_final-werks = t_text-werks.
    t_final-cmatnr = t_text-cmatnr.
    t_final-srlno = t_text-srlno.
    t_final-matnr = t_text-matnr.
    t_final-charg = t_text-charg.
    t_final-erdat = sy-datum.
    t_final-erzet = sy-uzeit.
    t_final-ernam = sy-uname.
    t_final-rstat = 'U'.
    append t_final.
    clear t_final.
endloop.
delete t_final where werks = ''.
describe table t_final lines g_line.
sort t_final by werks cmatnr srlno.
Deleting the Duplicate Records
perform select_data.
describe table t_final lines g_line1.
modify zbatch_cross_ref from table t_final.
if sy-subrc ne 0.
    write:/ 'Updation failed'.
else.
    Skip 1.
    Write:/12 'Updation has been Completed Sucessfully'.
    skip 1.
    Write:/12 'Records in file ',42 g_line .
    write:/12 'Updated records in Table',42 g_line1.
endif.
delete from zbatch_cross_ref where werks = ''.
ENDFORM.                    " modify_table
*&      Form select_data
      Deleting the duplicate records
FORM select_data.
select werks
         cmatnr
         srlno from zbatch_cross_ref
         into table t_zbatch for all entries in t_final
         where werks = t_final-werks
         and cmatnr = t_final-cmatnr
         and srlno = t_final-srlno.
sort t_zbatch by werks cmatnr srlno.
loop at t_zbatch.
    read table t_final with key werks = t_zbatch-werks
                                cmatnr = t_zbatch-cmatnr
                                srlno = t_zbatch-srlno.
    if sy-subrc eq 0.
      delete table t_final .
    endif.
    clear: t_zbatch,
           t_final.
endloop.
ENDFORM.                    " select_data
Reward Points if it is helpful
Thanks
Seshu

UCCE 8.5.3/8.5.4 call volume statistics not matching in interval tables

hello,
We have just migrated a call center to UCCE 8.5.3 that runs roggers and ICM call flow scripts that contain very basic flows. In each flow there is basically a one-to-one ratio of call type elements to select skill group elements.
Generally you would expect the call volume (as our scripts are written) to have almost the same call volume in the call type interval table and the skill group interval table, with allowable differences because of RONAs, etc. But basically somewhat close.
In general this does work but after a reboot of the roggers (A and B sides) (logger down first, then router and reversed to start), the skill group interval data lags greatly from the call type interval data, meaning maybe 10% of the call type interval volume. We have learned that completely shutting down both A and B side and then briinging it back up in order from scratch seems to alleviate the problem (until the next restart). We cannot just leave the servers alone though due to company security patching policies.
Cisco TAC had recommended patching to UCCE 8.5.4 which we have recently done, but the probelm persists.
I was wondering if this data discrepancy has ever been seen by anyone else or if possibly some system config issue might be self-deating us? Rebooting the roggers leaves the phone system itself working just fine for the call centers, but the recording of statistics to the skill group interval table is greatly impacted with almost no recording of volume in relation to the call type interval (and for comparison, the call type skill group interval table as well).
We would generally not worry about it, but the workforce management vendor that takes its feed from UCCE only uses the skill group interval, which is basically reporting almost no volume in the mentioned scenarios.
If anyone can provide any information it would be most appreciated/
Thanks.
Greg

Thank you for the response. The time source check is a great idea. We ran into problems before when internal web service servers did not match the PGs (CTIOS service) and CTI provideed stats did not match.
We will continue to work through TAC, but I was just wondering if anyone else had seen this (as 8.5.4 sid not fix it) and if maybe it could have been something self-defeating in our system configuration or scripting. We did not immediately know this was happening until our 3rd party workforce management vendor made us aware.
Thanks,
Greg

Test Cases required for BW Statistics to test in QA annd DEV.

HI All,
I am currently working on a support Project. My client has completed installing of Bw statistics in DEV and transported it to QA way back in 2006.Currrently before moving the BI Statistics data to PRD we have to test it in DEV and QA.
How to prepare sample test case for testing it in DEV and QA? Please Sugggest.

Hi,
this forum is for the SAP BusinessObjects BI Solution architecture. I would suggest you post your question to the BW forum.
ingo

Contract net value for Header Statistics is not correct

There is issue with value contract. The net value for Header Statistics is not showing correctly for some contracts. Especially, when we delete the PO line items or reverse all entries (GR and IR) for PO line item.
Contract has one line with account category ‘U’. The target value is 300,000.00 and total quantity released to date is 160,000. The net value for Header Statistics should be 140,000 but it is showing 600,000 which is over (double) the target value and user cannot release any further PO reference to this contract.
Earlier I defined net price for line item 300,000 and I changed net price to zero and execute report RM06ENP0 but it doesn’t work.
Please share your experience and thoughts.
Thanks,
Shah.

Hi Jurgen,
There are few Purchace orders with multiple line items and each line item for Purchase orders referencing the same line and same contract.
There is only one Purchase order has two deleted lines against this contract.
Theses deleted line's net price has changed to zero and there is no PO history.
Contract released order value is correct as there is only one line, but net price is wrong. and user is getting error for target value is excedeed by $nnn when trying to create purchase order.
Thanks,
Shah.

Report using BI Statistics

People, I activated the BI Statistics in SAP/BW.
The Multicube 0BWTC_C10 is active.
Will I can generate a report related to load data (time of loading, the load status, etc), using this multicube (0BWTC_C10)?

Hi Akash,
The below standard queries will provide you the required details,
Info
Provider
Bex Query
Technical Name
Bex Query
description
0TCT_MC11
0TCT_MC11_Q0140
InfoCube Status
0TCT_MC11
0TCT_MC11_Q0141
InfoCube
Correctness
0TCT_MC11
0TCT_MC11_Q0240
InfoCube Status: Analysis
0TCT_MC22
ZCS_CUBE_DATADETAIL_STAT
ZCS_CUBE_DATADETAIL_STAT
0TCT_MC21
ZTCT_MC21_Q_FB_01
Dashboard - process
chain historical loading time
0TCT_MC22
ZCS_STAT_SPEND_LOADS
Statistics Spend
Overview Loads
0TCT_MC22
ZCS_STAT_SPEND_LOADS_PERF
Statistics Spend
Overview Loads Performance
0TCT_MC22
ZTCT_MC22_Q_FB_02
Dashboard - DSO
loading time top 10
0TCT_MC22
ZTCT_MC22_Q_FB_04
Dashboard - IC
loading time top 10
0TCT_MC22
ZTCT_MC22_Q_FB_06
Dashboard - IO
loading time top 10
-Arun.M.D

Index Statistics Update - Problem

We had performance problem yesterday with FI report FAGLL03, it timed out in online execution and in background mode it took 5000+ sec to execute. Result was no more than 100 records.
Later with some investigation problem drill down to index usage of table FAGLFLEXA. We then updated the index statistics of table from DB02. After that report worked fine with execution time of 10-15 sec for same set of input.
However user, in morning , was complaining again about performance problem with same report FAGLL03. We did that update index statistics again and as it was the case yesterday it fixed the problem.
Later today I checked SQL server the job SAP CCMS_xxx_xxx_Update_Tabstats, which I guess is updating index statistics daily at 0400 hours, is working fine. I can't see any error log there. Daily job to check database consistency is also not reporting anything.
Anyidea what could be going wrong.
Basis Consultants are looking into problem however I am putting this case here if anyone of you had same problem and fixed it.
Thanks,
Pawan.
Edited by: Pawan Kesari on Dec 11, 2009 4:05 PM

Hi,
Appears the stats are dropped eveytime the job runs @04:00
Have a look at the table DBSTATC in trx: DB21 to see if it's setup to dropped the stats..
Mark

BW Statistics 0BWTC_C10 in BW 3.5

We have the BW Stats multi cube(0BWTC_C10) which currently consists of six cubes.
1. BW Statistics OLAP                                              0BWTC_C02
2. BW Statistics - OLAP, Detail Navigation                  0BWTC_C03
3. BW Statistics - Aggregates                                       0BWTC_C04
4. BW Statistics - WHM                        0BWTC_C05
5. BW Statistics: Condensing InfoCubes           0BWTC_C09
6. BW Statistics: Deleting Data from InfoCubes      0BWTC_C11
We have the data in all except 0BWTC_C02
Now I want to load the data in to it and want to develop some queries on the MultiProvider(0BWTC_C10)
Can any one help me in how to load the data to 0BWTC_C02??
Any help much appreciated.
Kind Regards,
BH

Hi Sesh,
1)
0BWTC_C02 is replaced by 3 cubes: 0TCT_MC01, 0TCT_MC02 and 0TCT_MC03
(here each mulitprovider is based on 2 cubes, one basic cube and one virtual cube.
For ex, 0TCT_MC01 has basic cube 0TCT_C01 and virtual cube 0TCT_VC01, the naming convention is same for rest 0TCT_C* and 0TCT_VC*)
Hope the above is clear
0BWTC_C03 was referring to RSDDSTAT table before, but this table has become obsolete in BI 7.0. Corrections have made to the extractor in BI 7.0 SAP_BW SP 9 such that the extractor refers to RSDDSTAT_OLAP. So you can use this cube as the way you were using in BW 3.x if you are above or equal to SP 9.
0BWTC_C04 - no migration is required, technical content 3.x is still valid.
0BWTC_C05 - is replaced by 0TCT_MC23 (0TCT_C23 and 0TCT_VC23)
0BWTC_C09 - no migration is required, technical content 3.x is still valid.
0BWTC_C11 - no migration is required, technical content 3.x is still valid.
2) There is virtual provider for all the replaced cubes, but the old cubes for which migration is not required dont have virtual cubes.
3) The new multiproviders have virtual cubes alreday.
Hope this helps.
Best Regards,
Rajani

How to remove the ALV Statistics option from Accounts user's userids

Dear Sir/Madam,
In our Accounts department each time one extra page is comming out. When the ALV Statistics option is make Unchecked, then it funtioninng normally that is, single page is comming out.
Is there any way to make this option permanently Unchecked ? If possible please advice and also whether there will be any unwanted implications of it ?
Please advice.
Thanks and Regards,
Pranab

Option 1 - Use SAP Report RSPRIPARADMIN you can set this for all users
Option 2 - user parameter SP01_FROM 0000000002 - This means print job will start from page 2
Option 3 - List -> Print -> click to properties button in print window -> expend cover sheets -> double click on ALV statistics , now uncheck the ALV statistics check box . now click on setting button and click on copy setting button
Edited by: Savo on Jul 1, 2011 4:06 PM

SAPinst error during phase Create DB statistics (sapcheck)

Hello all,
I am currently installing an SAP ERP 6.0 EhP4/NW7.01 Java system when I enncountered this error during the phase Create Database Statistics.
Error says
BR0801I BRCONNECT 7.00 (40)
BR0805I Start of BRCONNECT processing: cefukrjh.sta 2011-05-03 12.29.57
BR0252E Function fopen() failed for 'D:\oracle\EA1\sapcheck\cefukrjh.sta' at location main-11
BR0253E errno 2: No such file or directory
BR0121E Processing of log file D:\oracle\EA1\sapcheck\cefukrjh.sta failed
BR0806I End of BRCONNECT processing: cefukrjh.sta 2011-05-03 12.29.58
BR0280I BRCONNECT time stamp: 2011-05-03 12.29.58
BR0804I BRCONNECT terminated with errors
I've checked this directory and I did not find the folder sapcheck. that is because my sapcheck is located in a different drive (E:). why is sapinst looking at the wrong directory and how can i point sapinst to use drive E instead?
i was thinking maybe i could copy the folder sapcheck from drive E to drive d and continue with the installion. what will be its impact if i do this?
by the way, my OS is windows 2003.
please advise.
thank you very much!
regards,
cha cha

BR0252E Function fopen() failed for 'D:\oracle\EA1\sapcheck\cefukrjh.sta' at location main-11
BR0253E errno 2: No such file or directory
BR0121E Processing of log file D:\oracle\EA1\sapcheck\cefukrjh.sta failed
It seems that while defining the Path of SAP and Oracle there is something wrong that's the reason it is looking somewhere else. If you will copy from E Drive installation will continue but it will be keep searching on D drive everytime. As you are on initial stage to install a new System i would suggest to stop the installation Master and start it from Scratch and define the FIle System Directly once again as you want.
Regards,
Subhash

HP J9776A 2530-24G Statistics

Similar Messages

Maybe you are looking for