HP Laserjet 1022n Network installati​on WS 2008 R2 X64

i'm setting up a new printserveron WS 2008 R2 x64 OS.
I have a HP LaserJet connected to the network that i'm struggling with to install.
Via http://h10025.www1.hp.com/ewfrf/wc/softwareCategor​y?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=4393​...
I can't seem to select my OS. No WS 2008 R2 in list.
I assumed W7 64 bit was closest to my os.
So i selected this and tried to download driver.
There is only an .exe available, no seperate drivers packages.
However, when I try to launch the .exe hoping that this will auto installs the drivers.
First step i have to do is connect Printer USB Cable.
As i mentioned earlier, this is a NETWORK printer and it's not attached via USB.
I can't get past this "connect usb" screen.
I've been searching at non-HP websites looking for the correct driver but without success.
Anyone can help me out?

Hi Mahya,
Thank you for posting in Windows Server Forum.
Did you receive any particular error for your issue?
Please check the link provided by Hari, you can use RD Easy Print driver for server 2008 R2.In addition, if possible try using Universal print driver for your case. 
Using Remote Desktop Easy Print in Windows 7 and Windows Server 2008 R2
http://blogs.msdn.com/b/rds/archive/2009/09/28/using-remote-desktop-easy-print-in-windows-7-and-windows-server-2008-r2.aspx
Hope it helps!
Thanks.
Dharmesh Solanki

Similar Messages

  • HP LaserJet 1022n Printer via Wireless LAN

    Hi
    I just got a new Printer: HP Laserjet 1022n.
    Printing by Ethernet works just fine. Now i would like to print through W-LAN.
    I habe e Router with 4 RJ45 Ports; i tried printing through our Network but the printer doesn't show in the Printer-List anymore.
    I'm not sure where to beginn; this should be possible, right?
    Thanks for your help!

    Problem solved - i tried it with other Router and it works fine. It seems as if the FON-Software was causing the prolbem...

  • HP Laserjet 1022n & Windows 7 64-bit & spooling

    My home network has three desktop computers, one laptop and one tablet. Two of the desktops, plus the tablet are all running Windows 8.1. The laptop is running Windows 7 64-bit Professional, while the third desktop is running Windows 7 64-bit Home. All of the computers use the network to connect to the Laserjet 1022n printer that is also connected to the network (hard-lined). The Laserjet does have the latest Firmware installed onto the printer. All three of the devices that are using Windows 8.1 are able to connect and print fine from the printer, however it is the two Windows 7 computers that are having issues with the printer.
    The problem is that the spooling is not resetting once a print job has been sent. The print job will continuously print the print job indefinetly unless I go into the "c:\Windows\System32\spool\Printers\" folder and manually clear out the spool. I have downloaded both the Full HP software as well as the basic driver for the Laserjet onto both Windows 7 computers. I have tried running the repair feature and as well as just using the basic driver to add the printer. Nothing seems to be working correctly.
    The ONLY way for me to get the printer to work is to use one of the Windows 8.1 computers as a middle-man; connecting to that computer and sending the print job through that computer. Only issue is that it takes forever to spool the print job to the Windows 8.1 computer before it can start printing. These are fairly new computers; both purchased in the last year. Both have 4 Gigs of RAM so that is not the reason. So I am not sure what is going on.
    None of the computers are directly cabled to the printer and the main Windows 7 computer that I really need to have working with the laserjet is on the opposite side of the house (the Windows 7 laptop does not use the print feature that much,  so it is not AS critical).
    Any help would be much appreciated.

    Welcome to the HP Forums Hinalover,
    I see by your post that you are having issues with the print spooler on the Windows 7 computers.
    I can help you with this issue.
    Download and run the Print and Scan Doctor. It will diagnose the issue and might automatically resolve it. Find and fix common printer problems using HP diagnostic tools for Windows?
    Try running the Microsoft Fix It Tool to see if it will fix the print spooler.
    Diagnose and repair Windows File and Folder Problems automatically.
    You can also run the System File Checker to repair corrupted or missing files.
    System File Checker: Run sfc /scannow & analyze its logs in Windows 7 | 8.
    You might end up having to do a repair of Windows.
    Please let me know the results.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Connecting HP LaserJet 1022n

    Can someone help me connect my HP LaserJet 1022n to my E2500?  Note: not "HP LJ 1022nw" which is wireless version.
    Printer was attached to my old Linksys Wireles-G router.  Printer has a USB connection and an ethernet cable port.  Wth the old router I simply connected the printer via ethernet cable and made sure I entered the IP address when adding the printer to my old Windows XP Pro system.
    I went through Linksys installation process and added the printer as a wireless printer.  I now receive an error message "cannot print .... etc." but the 1 page print job is printed over and over many times.  I do not receive the error message or eroneous results when I attach the printer directly to my laptop via USB.  I'm not even sure if I'm receiving the message from Win8 or Linksys.  I am new to Win8.
    Any ideas on how I should proceed? 

    Make sure the cords are properly connected. Reset your printer to factory defaults. If it is just wired to the router, it would automatically get an IP address from the router. Reserve the printer’s IP address and then setup IP printing on the computer. On Windows 8, just search for Devices and Printers and add the printer. Follow the link below for detailed instructions. The link below shows instructions for Windows 7 which is just going to be the same with Windows 8.
    Configuring your network printer with DHCP reservation in your router
    Troubleshooting printing issues with your network printer
    Setting Up the PrintServer Using TCP/IP Printing on Windows 7

  • Installing x64 and x86 drivers for a HP Laserjet p1505n printer on Windows Server 2008

    How do you install both x64 and x86 drivers for a p1505n on a 2008 server? I have now managed to install 64 bit drivers but can't install x86 drivers in the normal way using Additional Drivers from the Sharing tab. I am also trying to do similar for a laserjet 1022n printer.

    On the 2008 Server x64 I installed the FULL driver package 163mb.
    I installed the HP P1505n on Server 2008 and made sure that was working.
    Then I went back in and did the Additional Driver thing and when it asked for the driver for x86 I went to the
    C:\hp_P1000_P1500_Full_Solution folder and scrolled to the bottom and there was the x86 XP driver.
    I hope this helps someone.

  • 'Laserjet 1022n Windows Update' causing printing problems: print jobs don't stop printing

    Hello,
    a few days ago, I installed the Laserjet 1022n Windows Update on my Windows 7 64 bits and since then, I can't print a page normally: the page doesn't stop printing. I am using a network port with TCP/IP.
    I made several trials to solve this problem:
    - uninstall the printer driver and installing it again (I tried the last version on the HP site and an older one that worked perfectly before)
    - update the firmware of the printer to the last version on the HP site.
    When I pause the printer and start the print job, you see it arriving in the list. Resuming the printer, the print starts on the printer but you see that the job stays in the list, flashing again and again. The printer keeps printing the same page.
    I don't know what I can do to solve this problem. There is no mean of uninstalling the HP Laserjet 1022n software update because it doesn't appear in the list of installed programs (well on the list of the done updates by the way op windows updates).
    I have the same problem printing on the same printer from another Windows  7 PC (with the same windows update done)
    But I have no problem printing with my laptop on another network printers.
    Is there someone having the same problem and how to solve it ?
    Thanks for answering
    This question was solved.
    View Solution.

    I found the solution on this site : http://www.tomshardware.co.uk/forum/59912-29-1022n-printer-stop-printing
    You just have to uncheck the chekbox "Enable two-way communication" on the "Ports" tab of the printer properties and it works normally again !!!!

  • HP laserJet 1022n How can I change IP adress?

    HP laserJet 1022n How can I change IP adress?

    It is advisable to set a static IP address for the printer:
    - Print a Network Config Page from the front of the printer. Note the printer's IP address.
    - Type that IP address into a browser to reveal the printer's internal settings.
    - Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
    - On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
    - Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
    - Enter your router's IP (on the Network Config Page) for the gateway.
    - Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS.
    - Click 'Apply'.
    Now, shut down the router and printer, start the router, wait, then start the printer.
    After this you may need to redo 'Add a Printer' using the new IP address.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • HP LaserJet 1022n Cold Reset 0.0.0.0

    Performed a Cold Reset on a HP LaserJet 1022n,  with a previously assigned static IP.
    Config page IP reads 0.0.0.0
    Config By - Manual
    I cannot connect to the printer to manage it over the web,
    This question was solved.
    View Solution.

    I think the best bet now is to do a fw update on the printer.   You will need to connect to the printer via a USB cable to do the update since your network connection is not working correctly.   Here is a link to the fw update.
    That should bring your printer up to date and/or clear the issue.  Give it a try.
    Although I work for HP, my posts and replies are my own.

  • Print to a Laserjet 4050 networked on an XP machine from my iPad

    How can I print to a Laserjet 4050 networked on an XP machine from my  iPad?  Can I use the AIO app?  does not find the printer.  Thanks.

    @Mojo-Risin 
    If I understand your question, you would like to use the AiO remote app on your iPad with your Laserjet 4050, correct? If this is case, unfortunately, the AiO remote app is not supported with the Laserjet 4050 and the iPad.
    Thank you.
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as Accepted Solution

  • I purchased a MacPro 2010 and is having trouble to add HP LaserJet 1022n to my printer list.

    Dear Administrator,
    I purchased a Mac Pro 2010.  I migrated from my MacBook Pro to Mac Pro.  Then, the HP LaserJet 1022n won't print.  I reseted printing system and now can't add that printer to my printer list.  Software Update have installed HP Printer Driver v. 2.16.1 on my system.  The printer is actually available in HP Printer Driver 1.1.1 update.  But, no matter how I do it, it always complained that the Driver software is currently unavailable and ask me to install it later.  I have downloaded the HP Printer Driver 1.1.1 update manually, but it won't install and showed my Macintosh HD as not a valid install target.  I tried to install the driver CD that came with the printer, but it complained that a newer version of the driver has been installed on the SSD hard drive.  Please help.
    My guess is that the HP Printer Driver 1.1.1 update is on the system but is corrupt, that is why the Add Printer command can't simply pick up the driver on the computer.  Other method also break down since they think I already have the driver installed.  I think that I needed to uninstall the HP Printer Driver 1.1.1 update to correct the system.  That is just my hunch.
    Please advice.  Thank you very much for your time and effort in this matter.
    Sincerely yours,
    Zigang
    Ph.D.
    <Personal Information Edited by Host>

    Have you tried un-installing the original (complete) software and re-installing it?
    Usually that does the trick. After that you can try the update if necessary.

  • LaserJet 2550n network printer on XP host PC, can't install Windows 7 client laptop

    Have Color LaserJet 2550n network printer connected to XP host PC. I can't install  Windows 7 client laptop for printer. The wireless network is fine, I can access documents back and forth, merely the printer doesn't work and there's no way to download 64bit drivers for this printer from HP. 

    Resolved, not solved. 
    I talked to HP product support. The Officejet Pro 8500 A910 will not install on Windows XP (at least the Home Edition) when networked through a router. It will install through USB. I uninstalled the program and reinstalled it with only USB connected to clean out all the network printer/scanner information. Product support claimed it would install through an ether net cable connected between the printer and computer but this does little good if you need internet access.

  • Unable to install hp Color LaserJet 3600n network printer on new Windows 7 (64bit) PC.

    Unable to install hp Color LaserJet 3600n network printer on new Windows 7 (64bit) PC. According to Microsoft Windows Compatibility Center website (http://www.microsoft.com/windows/compatibility/windows-7/en-us/Details.aspx?type=Hardware&p=HP%20Col...) this printer is compatible.
    I have tried everythingto no avail. HP will not support and have, very little online resources addressing this particular issue. What should I do?

    This may help: http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?&objectID=c02538616&lang=en&cc=us
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Problem with Lion 10.7.3 with hp laserjet 3600n network  printer

    Hi
    Problem with Lion 10.7.3 with hp laserjet 3600n network  printer
    Guys i am having a mad day with this new OS and some network printer none of them work with new LION,The software for this printer is currently unavaliable. Please contact the printers manufacturer for the latest software, i need the drivers for this, please give a hand with this issue
    Best Regards

    Exactly the same infuriating problem we and many others get with OS X from 10.6 on when Apple dropped Apple Talk.
    Having spent days fighting to get drivers that will run our older laser printers like HP5000, 5100, 2100, 2200 and 4MV, we came up with a simple solution:
    We use an iMac running 10.5.8 as a print server. All the 10.6 upwards Macs on the same network will see and add the printers immediately through the shared older (Apple Talk) iMac.
    Cheapest and simplest option really .... it'sannoying that a brand new Mac can no longer see existing network printers without complex investigation and trying various downloads.
    Answer is simple and cheap if you happen to own a 4 or 5 year old Mac with an OS lower than 10.6 which still has Apple Talk.

  • Why My IMAC OS X 10.6.8 Become Slow On The Network Between Window Server 2008

    Dear Sir,
    I am using IMAC 10.6.8, processor 3.06 GHz Intel Core i3, Memory 4GB 1333 MHz DDR3 and now my lovely IMAC become slow on the network between window server 2008 and my IMAC.
    Kindly advise for the above said issue how can I fix it. I already disable in my IMAC IPV6 and I am connect with airport not ethernet cable and my WIFI is LINKSYS modem and all other windows PC's are connected with the Gigabyte switch.
    Awaiting your soonest reply.

    Dear Sir,
    I am using IMAC 10.6.8, processor 3.06 GHz Intel Core i3, Memory 4GB 1333 MHz DDR3 and now my lovely IMAC become slow on the network between window server 2008 and my IMAC.
    Kindly advise for the above said issue how can I fix it. I already disable in my IMAC IPV6 and I am connect with airport not ethernet cable and my WIFI is LINKSYS modem and all other windows PC's are connected with the Gigabyte switch.
    Awaiting your soonest reply.

  • Is HP Laserjet 1022N eprint enabled?

    Is the HP Laserjet 1022n printer eprint enabled? Is there a nice list of HP printers that are?

    Hi,
    The HP Laserjet 1022 does not support cloud services as ePrint.
    You may find any supported printer for ePrint in the following document:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02814760&cc=us&dlc=en&lc=en#N1311
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

Maybe you are looking for