Hp laserjet 1320 is not printing

Hi, I have Hp laser jet 1320, three drivers ase given at hp website, i have tried all of them, printer is only printing a test page and then i give the command for printing a document but it does not prints and sometimes it shows that printer is failed to print this doc.please help

To resolve this issue, follow these steps:
1. In the BIOS of your computer, change the parallel port setting from "OS controlled" (or "Auto") to "Enabled". For information about how to change BIOS settings, see the documentation included with the computer or contact the computer's manufacturer.
 2. Click Start, and then click Control Panel.
3. Double-click System, click the Hardware tab, and then click Device Manager.
4. Double-click Ports, and then examine the existing LPT ports. Only one port is listed: LPT3.
5. Close the Device Manager window, and then click OK to close the System Properties dialog box.
6. In Control Panel, double-click Printers and Faxes.
7. Right-click the printer, click Properties, and then click the Ports tab.
8. In the PrinterName Properties dialog box, click to clear the LPT1 check box, and then click to select the LPT3 check box.
9. Click OK to close the PrinterName Properties dialog box.

Similar Messages

  • HP Laserjet 1320 will not print ?selected pages

    I have the HP Laserjet 1320 and when in a Word document and I want to print a selected page (i.e. page 2 of 4 only), under Pages on the Print Menu, I enter 2 or 2-2 and select print and it will not print!  I can scroll down to place the pointer on page and tell it to print "current page" and it will print - why will it not print when I enter the page number I want to print.
    Thanks
    gumboman

    My printer would not print multiple copies.  It would only print one page at a time.

  • HP Laserjet 4100 will not print in Snow Leopard

    Since I’ve installed Snow Leopard, I have not been able to print with my HP Laserjet 4100.
    My set-up: new 24” iMac, many hard drives and more. Two devices: HP Color Laserjet 5550 and HP Officejet J5750 are connected to the iMac through a USB Hub. Although initially scanning did not work with the J5750, I was able to make that work once additional drivers were downloaded from HP. Both work fine.
    I also have an older HP Laserjet 4100 which has been my steady workhorse for years. It only has Ethernet and serial port outlets. It is connected to an AT&T 2-Wired Ethernet Hub/DSL Modem (model 2701HG-B) that is connected to the iMac.
    I’ve contacted HP and Apple about this problem. None of the three people I worked with at Apple could help and the HP representative was unsure if they could help but that it would cost me $40 to find out. According to HP website, since Apple Talk no longer exists, we are required to input the IP for the device. For the 4100, the IP address is 10.0.1.100. I tried this two ways: in the “Add Printer” window under “IP,” inputted as the IPP, and inputted as the HP Jetdirect Socket (as per the HP instructions). When this is done, the printer shows up when you give a print command. However, it does not show up in the “Add Printer” window under “default” or anywhere else.
    Status: If I connect the 4100 Ethernet cable directly to the back of the iMac, the “Supply” level indicates the true level of toner in the 4100. However, it will not print. If I connect the 4100 Ethernet cable to the Ethernet hub, the supply level does not show nor can I print.
    Any suggestions?
    Chuck Stewart
    < Edited by Host >

    Well, another week has gone by without a solution.
    Again, here is the problem:
    I have a 24" iMac connected to a USB hub and an AT&T 2-Wire DSL/ethernet hub. When I upgraded to Snow Leopard 10.6.1 and now the update 10.6.2, the two printers on the USB hub work fine but the HP Laserjet 4100dtn does not print. This old printer has only ethernet or serial ports. I've downloaded and installed the HP driver updates from Apple and HP to no avail. According to HP, I must add the 4100 manually using its IP. I've followed the instructions while adding a printer to select IP- HP Jetdirect - Socket. The address of the printer is 10.0.1.100. When I type this in, the window says that this is a valid and complete address. It searches and then says the "Print Using:" is a Generic PostScript Printer. The driver for this printer, I believe, should be "HP LaserJet 4100 Series v.3010.107" Regardless, when I click Add the window "Determining Installable Options" shows "Status: Connecting to printer..." It never establishes a connection.
    The 2-Wire DSL/Ethernet Hub/Modem, has an IP of 192.1687.1.66, Submask 255.255.255.0 and Router (DNS) 192.168.1.254.
    If I plug the ethernet cable directly from the printer to the iMac, the supply level shows correctly but will not print. If I plug the ethernet cable from the printer to the 2-Wire and then to the iMac, it neither shows supply level nor prints.
    Any suggestion as to how to fix this problem? (I've been on the phone with 3 different Apple respresentatives and 1 HP representative with no success.)

  • Laserjet cm1312 will not print green

    laserjet cm1312 will not print green, all ink cartridges are full, green comes out yellow

    Hello @dour,
    Welcome to the HP Forums!
    I understand your concerns. Unfortunately, for this type of printer, I need to direct you to our Enterprise Business Community Forums. This will be the right section to troubleshoot this issue. Good luck.
    I worked on behalf of HP.

  • HP LaserJet 1320 won't print in color (Win7 64 bit, new cartridge)

    I can't get my HP Laserjet 1320 to print in color any more. Changed the cartridge. I'm on Windows 7, 64 bit, but the issue started before the upgrade to Win 7. I can't even find the selection for color vs black and white printing.

    The LaserJet 1320 printer is a monochrome printer, not a colour printer.

  • Laserjet 1320 - no duplex, print comes out offset, top 4 lines missing

    Hi,
    I have an HP Laserjet 1320 connected to an Ubuntu (Gutsy) server and shared as a SMB printer.
    Printing from Linux or Windows XP works fine: the print is aligned, I get duplex etc.
    When I print from my Macbook Pro running Leopard 10.5.1 I get the following:
    - The print alignment is offset vertically, resulting in the top four lines or so missing from each print (i.e. off the paper).
    - No matter what I sent in the print dialog duplex does not work.
    I have installed the latest driver from the HP site, but that didn't make any difference.
    Any ideas?
    Regards
    D.

    I found this fix for duplex from a 1320;
    http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&obje ctID=c00752270&jumpid=regR1002USEN
    The thrust is that the print option is set intra-application, not at printer level. Say launch word, select print, then click on copies and pages, this gives you the option for 2 sided. You can over type the "standard-1" with text such as "Duplex 2 sided printing", which then defaults to mail etc.

  • LaserJet 5000 will not print more than one copy at a time.

    We have recently moved our office.  A LaserJet 5000 which is used as an office printer is shared through one of the computers on the network in the exact same way it was more we moved.  But since the move it will not print multiple copies of the same document no matter how many copies the software tells the printer to print it will only print one copy then it stops.  Before the moved it worked fine.  If the software program such as Word told it to print 100 copies it printed 100 copies now one is the limit.   So if you want to printmore than one you have to hit print that many times.  It has 172 MB RAM.  Does anyone have any ideas of what might have happened????

    I have the same issue with a photosmart 2410xi. Did you ever get yours figured out?

  • My HP Laserjet 1020 will not print from Internet Explorer 9

    I just get an error message saying that "an error occurred on the script on this page."  The printer works fine with other software.  Moreover, Internet Explorer will print perfectly on my old HP deskjet 940c.  I've downloaded the latest driver for the Laserjet 1020, but it doesn't help.  Any suggestions?

    My Hp 1020 Laserjet will not print  when using Explorer 9, it did when using Explorer 8.
    I get an error :
    Unexpected call to method or property access
    Code: 0
    Url: res://ieframe.dll/preview:js
    It will print when using Mozilla FireFox
    What can I do ?

  • HP laserjet 1536dnf will not print pdf's

    My laser jet 1536dnf will not print pdfs.  Prints everything else.  I have adobe acrobat 9.  I have unistalled the driver/software for the printer and reinstalled.  Still not fixed.  When I pull up the pdf and select print, then hit ok, nothing happens.  However, I can print pdfs to the other printer connected to my computer.  This logically brings the conclusion that the issue is with the laser jet driver.  Does anyone have a clue as to how to fix this?

    Hi , I see that you are having issues printing PDF documents, just from the Laserjet M1536dnf printer. I will certainly do my best to help you. Try printing a page from the printer's User Guide, to see if you have the same results. LASERJET PRO M1530.Let me know the results. Print the PDF as an image: Open the original PDF file, if necessary.Click File, and then click Print, or click the Print icon. The Print window opens.Click Advanced. The Advanced Print Setup window opens.Select the Print As Image checkbox, change any other settings as desired, and then click OK.On the Print window, click OK again to begin printing.Run the Adobe updates. Product updates. If you appreciate my efforts, please click the 'Thumbs up' button below. If there is anything else I can help you with, just let me know. Thank You.  

  • HP LaserJet 4250 will not print

    I have an HP Laserjet 4250 that will not print from any of the 15 stations it is set up to.  I send print jobs to it, and I have to power the cycle the printer in order for it to print.  I have deleted and re-added the printer to the workstations, and still get the same issue.  The IP address is correct the IP port is good, I have reset factory settings as well.  Still will not print more than 2 jobs without it having to be turned off/on.  Any suggestions???
    Mike

    you writed few informations: OS?, which type installation local IP or Print server?
    try uncheck in tag advance: Enable advanced printing features

  • HP Laserjet Pro P1102W not printing even though it's installed...

    Hello everyone. I'm relatively new to Arch, especially new with configuring cups. I just bought an HP LaserJet Pro p1102w wireless printer. I set it up on my dads laptop via plugging it into the usb and it automatically ran the setup program and I selected to set the printer up for wifi printing. All went well and the printer works now wirelessly from his computer (Windows 7). I've been working at getting this printer to actually print without error but it refuses.
    I'm trying to print from leafpad, just a simple text file with little in it other than "linux test print" in the file. The print queue states "Processing - Not connected?" then it fails and gives me the option to "diagnose" the issue. So I click Diagnose. Then it pops up with a message stating that the "print server not exporting printers". It tells me to enable  the "Publish shared printers connected to this system" through the printing administration panel which is in Gnome apparenetly (I'm in XFCE) under System>Administration>Printing from the main menu. In XFCE there is no such area.
    I have cups version 1.5.0-1
    hplip 3.11.7-2
    What else should I do? Apparently the printer was installed successfully. I tried installing it and selecting the HPlip driver which installed fine but wouldn't print. Then I removed that one and installed it using the Apple driver (airprint?) and it won't print either.
    I've tried searching for help but all I find is that it will work with hiplip installed... It isn't working with that installed.
    I can't access the cups server via a browser. Is that the problem? I've opened the cups config page but I don't understand it and it says allow,deny under localhost or ugh i dont know, something about which users can access the server. Should I remove the "deny"??
    Please help me if you can. I'm totally lost and have no idea what to do to get this printer working on my installation of arch. Arch is fully updated as of a few days ago.
    Any help would be greatly appreciated. Thank you.
    -Brittany

    I can't access the cups server via a browser. Is that the problem?
    Absolutely.
        If you are starting cupsd from DAEMONS in rc.conf is it starting correctly or failing?   If your not you should be.  if it failing does start manually work?   
    if it's running you should be able to access via browser.  localhost:631   
    also see/try
    $ hp-toolbox
    CUPS interface better option IMO tho.
    EDIT spelling.... to much scotch B4 posting
    Last edited by jwbirdsong (2011-10-20 00:42:38)

  • HP LaserJet 1320 through wireless print server

    I'm trying to hook up an HP LaserJet 1320 through an old DP-311wireless print server. I can access the servier through IE when go to the servers IP address through Parallels, but if I go to the same address through Safari on the Mac side, I get a blank page (although I do get a popup asking for UID and passwd). I have been able to print to this printer - on this AirBook - using the same D-Link rint server - but I removed and reinstalled the printer to try to get the duplexer to work. Now I can't get the printer to work at all . . . bummer.
    Any thoughts?

    Update - I have gotten the printer to work under Parallels once I assigned it to an LPR queue. Still no progress on the Mac side

  • HP color laserjet CP2025 will not print. Help.

    I have a HP color laserjet CP2025, but it will not print. I installed the driver HP Color LaserJet CP2020 Series PCL 6. I have a Windows Vista Home Premium. There is a message to replace the cyan cartridge, but I assume if the printer has black ink, then it'll print in black and white. Do I need to replace the cyan cartiridge for it to print? What other options can I try to troubleshoot?
    Thank you.

    @kesler 
    ‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
    If you are unfamiliar with the Forum's private messaging please click here to learn more.
    Thank you,
    Omar
    I Work for HP

  • LaserJet 4600 will not print black

    My LaserJet 4600 has only 12-13,000 pages on it and will not print black ink. Magenta, cyan, and yellow print fine. The black cartridge works in my other 4600, and I've also tried the magenta in the black slot-- it will not print in that slot either...... Appears to me to be a hardware issue..... Any suggestions as to what the problem is, and is it something that I can fix? Or is it a job for a repair shop?........... Another aspect is-- is it cost prohibitive to fix?.. Thanks......................  

    Good day,
    To get your issue more exposure, I would suggest posting it in the commercial forums since your product is a commercial product. You can do this at Commercial Forums.
    Enjoy your day!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Laserjet 4L will not print

    I have windows 7 (64 bit); I have had the HP Laserjet 4L for a long time, and find it an excellent product. I waited for the win 7 drivers and downloaded them on February 28, 2010. All went well, the printer recognized everything, the ready light lit, the document showed in the queue as printing, but it would not print. I tried printing from different sources but all failed - even though each time it said it was ready to print.
    I do not know what else to do. Hope you can help.

    Hello EugeneZ,
    Welcome to the HP Support Forums!
    To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial LaserJet Forums.
    The support page for your product may be helpful in the meantime: HP LaserJet 4L/mL Printer series
    I hope this helps!
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Maybe you are looking for

  • Firefox box around zoomed out images issue w/ (xf86-video-intel)

    When I zoomout on a page firefox displays a insetted box around my images. Most notably in my webmail client, however it happens even on the forums if I zoomout. Regualar zoom: http://world.pyther.net/files/Firefox/regular_zoom.png (The way it should

  • Error trapping for 'Save' dialog open?

    I'm writing a program which will do an extensive amount of work in Photoshop, and I'm trying to make sure it's as idiot-proof as possible. Before starting the image editing code, I want to make sure the user hasn't left any dialogs open in Photoshop,

  • How to unlock the data from other user while editing

    Hi friends, I have created 4 maintenance views for a table. While editing data by using one view, I must be able to edit other data of the same table using other different view. But it is showing "The data is locked by user pagidala and can be displa

  • Photosmart B8350 Prints page bottom as black block

    My Photosmart B8350 printer sometimes prints what should be blank space at page bottom as a large black block. This mostly occurs on the last page of a set, or  the bottom of a single page,  but have had intermediate pages (eg. pages 2 & 4 of 5) that

  • Still color in photos after converting to B&W

    Hi there, I have a very strange problem. After converting pictures to black and white in Lightroom (doesn't matter if I choose B&W in the basic menu, set the saturation to 0, set the HSL saturation sliders to 0 or choose a B&W preset) my pictures sti