HP LaserJet 2840 & Snow Leopard

Don't Buy HP.
I have this all in one printer with extended warranty that HP refuses to adapt their software for snow leopard. So no scanner, no fax. It prints and that's it!
Talking with HP corporate (888-943-8476) they apologize, but state that the President of HP has spoken and will not support 10.6 with software. The rep actually suggested I go back to the "old OS"! Then I get an email about their exchange program. Spend another $600-800 for another HP that may not be supported when 10.7 is launched.
Let's Go Apple, how about a line of printers and scanners! I'd love to see HP lose the Macintosh market!

Try this:http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us &prodNameId=445197&prodTypeId=18972&prodSeriesId=445194&swLang=8&taskId=135&swEn vOID=4082

Similar Messages

  • HP2100TN Laserjet to Snow Leopard.

    The HP Laserjet 2100 TN would not print after installing Snow Leopard. Finally I found the answer.
    Delete HP 2100 Tn Laserjet from printer list.
    Then add it back. When you do, it will find the drivers that are included in Snow Leopard and it will finally print.

    Neither your programs nor data should be effected if everything works perfectly.
    I don't know about you but I don't trust my data to everything working perfectly so I alway backup frist before doing an ungrade.
    I figure it is better to have a backup and not need then it is need a backup and not have it.
    Allan

  • HP LaserJet and Snow Leopard

    I have a new 24 inch Apple iMac (intel) that is currently connected to a HP 4000N LaserJet printer via ethernet connection and AppleTalk. How can I use this laser printer with Snow Leopard if AppleTalk in longer available. Any suggestions would be appreciated.

    The easiest way to configure the jet direct is through it's built in HTTP server/configuration app.
    Do you have a DHCP server on your network (Either being provided by an actual server, or router?)
    By default the printer should have come configured to get an IP address from a DHCP server, unless IP was turned off, or it was assigned a local IP address before (If you bought it used.)
    Look on configuration sheet. If the IP address was assigned by DHCP, the first 3 octets should match your networks (Imacs) address. IE iMac 192.168.1.x and printer 192.168.1.x. Subnet mask should match and the router should be pointing to the same place.
    If this is the case. go into your web browser, and go to http://192.168.1.x (x being the last octet that matches the printers ip address.)
    if the configuration page shows a "Link local" ip address IE 169.x.x.x or some other funky ip address like 10.x.x.x. It either can not find an IP server, OR it is already setup with a manual address. In which case you will have to set ip up by the front panel.
    Would be happy to walk you through it, if it is like my 4500N. Or I'll download the manual.

  • HP Color LaserJet 2840 Incompatible with MAC OS 10.6 Snow Leopard

    The printer defaults to "pause" when attempting to print. Clicking "resume printing" does not unpause the printer. I spent one hour with Apple tech support yesterday with no resolution.
    I removed the printer from System Prefs, then reinstalled, but that did not resolve the issue.
    HP tech support advised designating "Generic PostScript Printer" in the Print Using box when then adding the printer, but it still defaults to "Pause" when attempting to print anything.
    No problems with the Canon Pixma.
    Advice would be much appreciated.
    Message was edited by: biddymon

    Upon upgrading to Snow Leopard, I could print but could not scan. Deleted all existing printers that pointed to my CLJ 2840. Uninstalling and then reinstalling the 10.5 drivers resulted in a dialog box that stated there was a problem installing /System/Library/Extensions/hpcolor_lj_2800series.kext
    The printer was not automatically found, and could not be manually added via HP Setup Utility. I decided to fix the problem with the kernel extension (kext).
    I opened a terminal and ran the command
    sudo kextutil /System/Library/Extensions/hpcolor_lj_2800series.kext
    which informed me that there were problems with the permissions on that kernel extension. I then ran the commands
    cd /System/Library/Extensions
    sudo chown -R root:wheel hpcolor_lj_2800series.kext
    sudo chmod -R g-w,a-w hpcolor_lj_2800series.kext
    and then rebooted and that seemed to do the trick.
    The only thing that doesn't work now is the Fax fuctionality. the URL for the fax is set to "file:///dev/null", which doesn't seem productive at all. I'll post when I discover anything there.

  • HP Laserjet 4100 will not print in Snow Leopard

    Since I’ve installed Snow Leopard, I have not been able to print with my HP Laserjet 4100.
    My set-up: new 24” iMac, many hard drives and more. Two devices: HP Color Laserjet 5550 and HP Officejet J5750 are connected to the iMac through a USB Hub. Although initially scanning did not work with the J5750, I was able to make that work once additional drivers were downloaded from HP. Both work fine.
    I also have an older HP Laserjet 4100 which has been my steady workhorse for years. It only has Ethernet and serial port outlets. It is connected to an AT&T 2-Wired Ethernet Hub/DSL Modem (model 2701HG-B) that is connected to the iMac.
    I’ve contacted HP and Apple about this problem. None of the three people I worked with at Apple could help and the HP representative was unsure if they could help but that it would cost me $40 to find out. According to HP website, since Apple Talk no longer exists, we are required to input the IP for the device. For the 4100, the IP address is 10.0.1.100. I tried this two ways: in the “Add Printer” window under “IP,” inputted as the IPP, and inputted as the HP Jetdirect Socket (as per the HP instructions). When this is done, the printer shows up when you give a print command. However, it does not show up in the “Add Printer” window under “default” or anywhere else.
    Status: If I connect the 4100 Ethernet cable directly to the back of the iMac, the “Supply” level indicates the true level of toner in the 4100. However, it will not print. If I connect the 4100 Ethernet cable to the Ethernet hub, the supply level does not show nor can I print.
    Any suggestions?
    Chuck Stewart
    < Edited by Host >

    Well, another week has gone by without a solution.
    Again, here is the problem:
    I have a 24" iMac connected to a USB hub and an AT&T 2-Wire DSL/ethernet hub. When I upgraded to Snow Leopard 10.6.1 and now the update 10.6.2, the two printers on the USB hub work fine but the HP Laserjet 4100dtn does not print. This old printer has only ethernet or serial ports. I've downloaded and installed the HP driver updates from Apple and HP to no avail. According to HP, I must add the 4100 manually using its IP. I've followed the instructions while adding a printer to select IP- HP Jetdirect - Socket. The address of the printer is 10.0.1.100. When I type this in, the window says that this is a valid and complete address. It searches and then says the "Print Using:" is a Generic PostScript Printer. The driver for this printer, I believe, should be "HP LaserJet 4100 Series v.3010.107" Regardless, when I click Add the window "Determining Installable Options" shows "Status: Connecting to printer..." It never establishes a connection.
    The 2-Wire DSL/Ethernet Hub/Modem, has an IP of 192.1687.1.66, Submask 255.255.255.0 and Router (DNS) 192.168.1.254.
    If I plug the ethernet cable directly from the printer to the iMac, the supply level shows correctly but will not print. If I plug the ethernet cable from the printer to the 2-Wire and then to the iMac, it neither shows supply level nor prints.
    Any suggestion as to how to fix this problem? (I've been on the phone with 3 different Apple respresentatives and 1 HP representative with no success.)

  • LaserJet printer no longer works after installing Snow Leopard

    Since installing Snow Leopard, my LaserJet printer no longer works.  Spent 5 hours on the phone to Apple Support without any satisfaction.  Any suggestions?  I'm desperate.......

    Go to the HP web site and download the latest drivers for your OfficeJet.
    http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=219&lc=en&cc=us&dlc=en&sw _lang=&product=3919449#N225

  • Laserjet 8000DN issue with Snow Leopard 10.6.2

    Hello,
    I am having a connectivity issue with a LaserJet 8000DN. The previous iMac was connected to the printer via a D-Link switch, and I assume it was using AppleTalk via Ethernet to read the printer. The OS installed on that machine was OS X Leopard.
    We had to replace the iMac, and the unit we purchased is a new Intel iMac 21.5" with 10.6.2 fully updated. In doing my research, I understand the drivers are already installed and need not be updated.
    My steps thus far:
    1) Print the configuration file from the printer.
    2) System Prefs>Print and Fax>Add Printer
    3) Choose JetSocket
    4) Select IP and enter the IP Address from the configuration file.
    5) Click Add.
    The dialogue indicates that it's trying to connect and shows a configure or cancel button. I choose configure and the printer appears in my list with a green indicator showing that the iMac sees it.
    However, when I send a job to the printer, I continuously get the "unable to connect to the printer, will try again in 30 seconds" message. I have tried every possible combination, i.e. LDP etc., to no avail.
    A phone call to Apple did not provide a solution, even when we connected the printer directly to the Ethernet Port which really isn't an option anyway.
    Other Information:
    a) I suspect my problem is directly tied to the unavailability of Apple Talk in Snow Leopard.
    b) I have a static I.P. address assigned to the Mac from our ISP in the 176.xxx range - and The I.P. for the printer shows as 192.xxx - Is this a conflict?
    c) I am not using an Airport - We are stuck with a Westell DSL Router that has no ports available.
    d) Someone suggested a Print Server connected to the D-Link so that the iMac and the Dell on the network could use the printer.
    Any enlightenment will be extremely appreciated - This is a crucial operation for our business, and if it requires that we look for a new printer solution, we will need to move ahead swiftly.
    Thanks!

    a) The reason you cannot configure as you have been able to do in the past is because of the lack of AppleTalk, but you should be able to reconfigure things to work.
    b) If your printer is at an address which is outside of the subnet mask of the router, that is a problem.
    c) If you have a router, but not enough ports, the switch provides more ports.
    d) The printer is network capable, so you do not need a print server.
    So it looks like your problems are from your network setup.
    I take it that your ISP has provided you with a fixed IP address. You should have the output of the modem connect to the WAN port of the router. The LAN ports should be connected to your computers and other network devices, and if you need more ports, connect one port to the switch, and connect the other devices to it.
    The router should be configured to connect to the internet through its WAN port. From that, it should distribute that connection to your computers, to the addresses it is configured to provide. Those are usually in the 192.168.xxx.xxx range, but could be different. You should be able to change them. If the router LAN address is 192.168.1.0 and subnet mask is 255.255.255.000, the things that you connect to it can have address from 192.168.1.1 to 192.168.1.255.
    You should be able to change the address on the printer if you need to. The instructions should be in the printer documentation, or available on the HP website.
    You probably have all the hardware you need, but you need to look at your network configuration, decide whether it is correct or not, and make adjustments to get this working.
    A word of warning: If you have a fixed IP address because you have a server connected directly to the Internet, you need to configure your router appropriately. If you do not understand all of this, you may need someone familiar with network setup to help you.

  • Snow Leopard Breaks Bonjour Printing (HP Color Laserjet)

    Hi,
    I have a MacBook (newly reformatted) with the newest version of print drivers from HP's website, connected to a HP Color Laserjet CM1312nfi, with print sharing enabled and "share this printer over the network checked". It used to work well for Bonjour printing from all my other leopard macs in my house, before I updated to Snow Leopard.
    All of the computers I mention here are fully updated.
    On the other computers....
    The printer shows up in add a printer under Bonjour, but it takes a long time to find the driver. I have tried printing using the "Generic PostScript Printer" driver as well as the HP Color Laserjet cm1312MFP driver, but both get stuck at "Connecting to Printer". After a few minutes of this they peter out and just mark the job as completed.
    This is all while the printer is awake and the host computer is awake.
    Another computer, without the HP Printer solution software installed, but that still comes up with the HP Color Laserjet cm1312 MFP drivers, will say "Connected to printer" then automatically mark the job as on hold. No matter how many times I reset the print queue, on this computer nothing works.
    These computers are all running 10.6.
    I can print directly from the computer that is hosting the bonjour printer without any problems.
    Any suggestions?
    Thanks,
    Josh

    Josh,
    First, let me make sure my assumptions are correct. The printer is USB connected to the Mac that has printer sharing turned on, and the other Macs find the shared printer via Bonjour. All the Macs are running Snow Leopard. The computer with the printer connected via USB prints just fine. All of the other computers don't work.
    So, let me ask this. If you open up the Sharing System Preference, and select Printer Sharing, Printer Sharing is turned on, the printer you want to share is listed in the list with a checkmark next to it, and the Users is setup so Everyone Can Print. Also when you open up the Print & Fax System Preference and click on your printer, the "Share this printer on the network" checkbox is on as well.
    Next make sure that all the computer are running the HP Drivers version 2.2 from Apple Software Update (or downloaded from [Apple.com|http://support.apple.com/kb/DL907]).
    If all of this is true, let me ask if you connect the device to Ethernet (if possible at least temporarily) if all of the computers can find and print to the CM1312? This might help narrow things down.
    Just trying to help.
    Andrew
    Message was edited by: HP Mac Architect

  • HP Laserjet 3015 won't print after Snow Leopard

    Ok, so I upgraded to Snow Leopard, and now I can't print anything on my Laserjet 3015. I've tried uninstalling the printer and then reinstalling it, but still nothing. It seems that any time I try to print it says the printer is "paused". If I press the "resume printer" button while the document is in cue, it doesn't resume the printing. If I delete the document and then press the "resume printer" button it shows that the printer goes back into a ready state. Any suggestions? Thanks!

    Both SL and HP have recently updated their software. Have you upgraded to SL 10.6.1 and the latest version of HP drivers?

  • HP Laserjet 4mp won't print with Snow Leopard

    My great Laserjet 4mp prints just fine with OS 10.5.8 but not with Snow Leopard (10.6.2) on my new iMac. Have spent three plus hours with senior level Mac Techs to no avail. The printer screen shows the correct printer and driver and indicating valid connection, but when attempting to print I get the message "Unable to print, try again in 30 secs". Since 10.6 doesn't have Appletalk, am unable to use it; techs have tried to use the 4mp driver supplied with Snow Leopard and also downloaded it separately from the web site. We (they) have also tried using all methods (IP, Daemon, and HP Jet Direct using Ethernet and Serial to USB connections). Techs have talked with HP techs and have no other solutions. The security system is off. Any suggestions are welcome! Thanks!

    I've read the threads and don't understand some, but I think we (the Apple support techs and I) have tried the ones I recognize. One new idea--in a reply to a similar post someone mentioned being sure to use additional data when using the IP address-- submask address or some such, I
    haven't been told to do this--should I? (I can get it from the printer readout if told what to get.) Also, in another post someone suggested deleting the OS 10.5.8 driver that was transferred when all the data from my old iMac G5 was moved over, saying that it would interfere. If true, how do I do that?
    What I really need is a stepwise instruction on which connection to use (Ethernet, Serial to USB, or parallel port are the only options); which protocol to use (IPP, Line Printer Daemon, or HP Jet Direct socket, whatever they are); what to put in the Address line (the IP address is the one used by Apple techs); what to put in the Queue line (techs said to leave it blank); what to put in Name and Location blocks, if anything; and what to put in the Print Using line (techs have unsuccessfully tried Autoselect, Generic, and the HP4mp driver selected both from the Select Printer Driver option and from the driver downloaded directly from the HP web site).
    I'd be grateful for this help or even advice on where I can get it! (With this new computer I still have free telelphonic Apple tech support but they've given up.) Thanks!

  • Laserjet 2100 TN via ethernet to MacBook Pro 2009 (Snow Leopard)

    I've been given an HP Laserjet 2100 TN. It was previously suceessfully used with a MacBook pro via an ethernet cable.
    I'm trying to set it up at home but failing to get it to connect with my MacBook. I'm using Snow Leopard.
    I've read lots of connection tips in discussion forums but not found a solution that works for me.
    I've managed to print a configuration sheet which tells me in printers HP JetSend Address.
    I've tried using this to add the printer through System Preferences but the computer is not connecting with it.
    Do I need a parallel cable or is the ethernet cable enough?
    I think I'm missing something obvious!
    Sarah

    Sorry to post in the wrong place! And thanks for your input. SCSI is a good call - the parallel cable didn't look quite right and that may explain why. Can I add a few more experiences to help explain where I'm at:
    - Snow Leopard seems to think the drivers should be included in the OS, but I don't know how to access them.
    - I found and installed a driver but couldn't find how to access it when adding the printer.
    - When I'm in ADD PRINTER
        - I guess I need an IP address - is this the one I find on printer info?
        - I saw a forum that recommended LPD as best choice for old priters so I'm using that
         - It defaults 'Print using' to Generic Postscript Printer'. I've tried changing it to Generic PCL Laser Printer as it is a laser prointer, but neither help make it work
         - Once I've setup the printer, when I run a test page the printer fails to connect and goes on hold
    I don't think I'm explaining myself very well - mainly because I'm quite out of my depth trying to did this! I can't find anything in the printer handbook which helps. Do you have any advice for a novice trying to add a printer it would be much appreciated.

  • HP Laserjet 2100TN - how to add IP printer in Snow Leopard

    I am not a very technical person, so this was quite an ordeal for me.  I was very frustrated by the process and almost gave up.  I am glad that I did not
    I just upgraded to Snow Leopard and after many hours of reading blogs and instructions etc. I finally got my HP LaserJet 2100TN network printer to print in SnowLeopard.   I am running a 24" imac.
    All of the blogs/support documents tell you that you have to enter the IP address of the printer to set up an IP printer.  To obtain the IP address for the printer, you are told to print a Configuration Page.  But I had no idea how to do that.  So I found a manual online for my printer, learned that if I pressed the Job Cancel and the Go button at the same time that I would print a configuration page.  And it did !!!!  It was listed under Printer Informations as HP JetSend Address: ip: 192.xx.x.xx. (I left out my IP address as yours will be different.)  I then used the Network application located under Utilities, went to PING, entered the IP address and I pinged the printer.  The ping was successful.  Then I used the instructions provided at the link below  to add the IP printer.  Here is the info for the add printer info: http://support.apple.com/kb/HT4507.
    Here is the link for the LaserJet 2100 manual.
    http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/bpl06466/bpl06466 .pdf
    Good luck.

    Many, many thanks. This worked for me.
    My HP 2100TN is connected to a router and pinging the JetDirect ip address didn't work at first. After many tries and variations under "Print & Scan" sys prefs, the ping did work with the JetDirect ip address and I finished connecting by following your helpful instructions and links.
    The HP 2100TN now prints from OSX 10.8.5 on a "late 2012" 27-inch iMac. The HP 2100TN printer drivers were copied to the sys printer folder from a previous computer running OSX 10.5.8 and which always printed sucessfully through this same router to the 2100TN and still does.
    An even worse problem was trying to log into Apple Support Communities with the "username" endless runaround. I finally got to a "Find my Apple ID" link and discovered I had an old Apple ID which I didn't know still existed. I changed the password on that ID and then logged into ASC using the old ID. The login took me straight into the forum and displayed my old and long-forgotten ASC username for that ID. Why that worked, who knows?

  • Print to HP LaserJet 4mp via ethernet on Snow Leopard

    Well, after tons of research I have ended up printing thru my OLD mac via shared printer on the network. But I would hope there is a better way. I have a Mac Pro, 10.6.3 connected to a HP LaserJet 4MP via ethernet router via RJ45 cables, works great on ALL my other equipment, even the PC but refuses to show up in Snow Leopard. I tried the standard stuff like giving it an IP address that would match my current network settings, no luck, tried Asante, no luck. I realize it's hard to support a decade old printer but what's all the GREEN CRAP about if I have to keep throwing away equipment that still works, and beautifully. Had to ditch my quad PPC unit because of adobe. Now I can't print. HP was no help, apple support is WAY too expensive since I bought my machine used and they won't sell me an apple care agreement. Anybody have any more suggestions? MIO must stand for missing instant output. ANY suggestions would be appreciated as I've tried all the ones in the discussion forums so far.

    Since the 4MP is a PostScript printer, there should be any number of print servers that work with it. It might even work with your router. But it is not going to just "show up" on your computer like it did with AppleTalk. You will need to provide the computer with all the information it needs for an IP connection.
    You can get help with that here, but you need to provide information, like the model of the router.

  • Snow Leopard & HP LaserJet 5M

    Ever since I upgraded to 10.6, my HP LaserJET 5M has been inoperative due to the lack of Apple Talk support in Snow Leopard. I was using Apple Talk over Ethernet(?) and I cannot see or find any IP Address from my Name Server information using NetStat.
    Anyone have any ideas to keep this old printer going? It has been a work horse for many years and probably many more if I could only solve the communication issue.
    HP claims the LaserJet 5M is supported with their new drivers, but I have had any luck with communications between my MacBook Pro and the printer.

    Seen these?
    http://discussions.apple.com/search.jspa?search=Go&q=LaserJET5M

  • HP Color LaserJet 3500n - Slow Printing in Snow Leopard

    I've installed all of the HP Printer Updates for Snow Leopard (even manually downloaded the latest entire HP Printer Update), Reset the Printing System and reinstalled all of my printers, but I still continue to have an issues where it takes over 4 minutes for the first page of a print job to print... This is a network printer with an external HP JetDirect (Model #J7942A) box and the slow printing occurs with all Snow Leopard machines. Firmware for both the Printer and the JetDirect box are at the latest versions...
    I did notice that Apple's kb article indicates that the latest print driver for this printer is 1.0.2, but my driver indicates 1.0.1... Is the kb article incorrect? Any ideas why I'm not getting the 1.0.2 driver? Suggestions?

    I've got the same problem with a Color Laserjet 3550 + JetDirect en3700.
    For security reasons, I disabled SNMP v1/v2 on JetDirect. Everythings works fine on Leopard.
    I got this problem after upgrading to Snow Leopard (ver. 10.6.2 with HP printer driver 1.0.1).
    Looking at network traffic with Wireshark, I've noticed some timeout on SNMP v2 packet directed to the printer.
    I've enabled SNMP v1+v2 on JetDirect and now everithings works fine, but security problems related to unsecure SNMP version are now open.
    I've upgraded HP printer driver, but I can't find driver version 1.0.2, as mentioned in http://support.apple.com/kb/HT3669#HP.
    Any suggestion?

Maybe you are looking for