HP LaserJet MFP M476dw paper size mismatch when copying or scanning from ADF

We have HP Color LaserJet MFP M476dw that has an issue when copying or scanning from the ADF. 
Put a single A4 sheet in the ADF and choose copy, with all settings correct & no resizing, and the output copy is moved down the page (increased top marging by a couple of inches).
My initial thoughts were a paper size issue (e.g. treating A4 as Letter or vice versa) but all settings look correct.  I have even done a reset and started over and the problem remains.
If I take the original and place it on the flatbed and copy from there with all the same settings then it works fine.
There is a similar issue when scanning from the ADF.  Again, scanning from the flatbed works fine.
I've tried all I can think of.  Does anyone have any further suggestions?  Could it be a fault in the ADF?
Here's the full device settings info:
Device Configuration
[Shop for Supplies][Support]
Product Information
Product Name:
HP Color LaserJet MFP M476dw
Formatter Number:
YF10C9X
Serial Number:
CNB7G2H6T9
Service ID:
24113
Firmware Datecode:
20131122
Disable Fax:
No
Telecom Version:
05-031-001
Location:
UK
ADF Installed:
Yes
Max Monochrome Print Quality:
600x8
Max Color Print Quality:
ImageREt 3600
Controller Number:
72
Duplexer Version:
0
Device Description:
HP Color LaserJet MFP M476dw
Language:
English
Default Settings:
Self-managed
Asset Number:
Your Company Name:
Contact Person:
Device Location:
Geo Location:
Product Security:
Off
Wired HW Address:
fc:15:b4:78:28:46
Wireless HW Address:
54:35:30:2f:d7:fc
Network In Use:
Wired
Host Name:
NPI782846
IPv4 Address:
192.168.9.18
IPv6 Address:
FE80::FE15:B4FF:FE78:2846
Total Memory:
256 MBytes
Available Memory:
117.7 MBytes
Installed Personalities and Options
PCL6
(20040201)
AirPrint
PCL
(20040201)
PDF
(20040201)
PS
(20040201)
USB Flash Drive:
Empty
Impressions
Total Impressions:
10684
Monochrome Impressions:
4799
Color Impressions:
5885
Total Equivalent Impressions (A4/Letter):
10684.0
Monochrome Equivalent Impressions (A4/Letter):
4799.0
Color Equivalent Impressions (A4/Letter):
5885.0
Duplex Sheets:
1223
Jam Events:
0
Mispick Events:
4
Photo Color Impressions:
0
Photo Monochrome Impressions:
0
USB Flash Drive Insertions:
0
Images Scanned to USB Flash Drive:
0
Copy Flatbed Images Scanned:
373
Copy ADF Images Scanned:
409
Copy Monochrome Impressions:
1122
Copy Color Impressions:
102
ADF Images Scanned to Host:
0
Flatbed Images Scanned to Host:
0
Images Scanned to E-mail:
0
Images Scanned to Network Folder:
0
Fax ADF Images Scanned:
23
Fax Flatbed Images Scanned:
1
Fax Impressions:
18
Images Sent from PC:
0
ADF Images Scanned:
1149
Flatbed Images Scanned:
779
Scanner Jam Events:
8
Paper Settings
Default Paper Size:
A4
Default Paper Type:
Plain
Tray 1 Size:
A4
Tray 1 Type:
Letterhead
Tray 2 Size:
A4
Tray 2 Type:
Plain
Paper Out Action:
Wait Forever
Manual Feed:
Off
Duplex:
Off
Bind:
Long Edge
Print
Auto Continue:
Off
Number of Copies:
1
Courier Font:
Regular
Orientation:
Portrait
Monochrome RET:
On
Wide A4:
No
Monochrome Resolution:
600
Monochrome Bits per Pixel:
8
Color Resolution:
600
Color Bits per Pixel:
32
IO Timeout:
120 Seconds
Jam Recovery:
Auto
Personality:
Auto
Print PS Errors:
Off
USB Flash Drive
Print Documents:
Number of Copies:
1
Paper Size:
A4
Paper Type:
Plain
Fit to Page:
On
Collation:
Off
Output Color:
Color
Print Photos:
Image Size:
10 x 15 cm
Paper Size:
A4
Paper Type:
Plain
Lighter/Darker:
<-----*----->
Number of Copies:
1
Output Color:
Color
Scan Settings:
Scan Resolution:
150
Scan File Type:
PDF
Scan Paper Size:
A4
Flatbed Scanner:
Single Page
Document Feeder:
1-Sided
File Name Prefix:
scan
Output Color:
Color
Copy
Optimize:
Auto Select
Lighter/Darker:
<-----*----->
Paper Size:
A4
Paper Type:
Plain
Collation:
On
Number of Copies:
1
Reduce/Enlarge:
Original=100%
Draft Mode:
Off
Tray Select:
Auto Select
Two-Sided:
1-Sided to 1-Sided
Multi-Page Copy:
Off
Fax
Your Company Name:
HP Fax
Answer Mode:
Automatic
Rings to Answer:
2
Distinctive Ring:
All Rings
Dial Prefix:
Off
Fax Resolution:
Fine
Lighter/Darker:
<-----*----->
Fit to Page:
On
Glass Size:
A4
Dialing Mode:
Tone
Redial if Busy:
On
Redial if No Answer:
Off
Redial if Comm. Error:
On
Detect Dial Tone:
Off
Billing Codes:
Off
Extension Phone:
On
Stamp Faxes:
Off
Private Receive:
Off
Confirm Fax Number:
Off
Allow Fax Reprint:
Yes
Print Duplex:
Off
Fax/Tel Ring Time:
20
Fax Speed:
Fast (V.34)
Error Correction:
On
Forward Fax:
Off
Block Junk Faxes:
Off
Phone Line Volume:
Medium
Alarm Volume:
Medium
Ring Volume:
Medium
Key-Press Volume:
Medium
Fax Confirmation:
Never
Fax Error Report:
Never
Include First Page:
On
Auto Log Print:
On
Print T.30 Trace:
Never
Paper Types
Plain:
Normal
HP Matte 90g:
Normal2
HP Matte 105g:
Heavy
HP Matte 120g:
Card stock
HP Matte 150g:
Extra Heavy
HP Matte 200g:
Extra Heavy
HP Glossy 120g:
Glossy
HP Glossy 150g:
Glossy
HP Tri Glossy 150g:
Glossy
HP Glossy 200g:
Heavy Glossy
Light 60-74g:
Light
HP EcoSMART Lite:
Extra Light
Intermediate:
Normal2
Mid-Weight 96-110g:
Heavy
Heavy 111-130g:
Card stock
Extra Heavy 131-175g:
Extra Heavy
Hvy Glossy 111-130g:
Light Glossy
X-Hvy Glossy 131-175g:
Glossy
Card Glossy 176-220g:
Heavy Glossy
Color Transparency:
Transparency
Labels:
Label
Letterhead:
Normal
Envelope:
Envelope
Heavy Envelope:
Heavy Envelope
Preprinted:
Normal
Prepunched:
Normal
Colored:
Normal
Bond:
Heavy
Recycled:
Normal
Rough:
Heavy
Heavy Rough:
Heavy
HP Tough Paper:
Tough Paper
Opaque Film:
Tough Paper
Energy Settings
Sleep/Auto Off After:
30 Minutes
Wake on These Events
USB Job
Yes
LAN Job
Yes
Wireless Job
Yes
Control Panel
Yes
Fax Ring
Yes
Shut Down After:
Never
LaserJet Updates Settings
Check Automatically
Yes
Prompt Before Install
Yes
Allow Downgrade
Yes
Allow Updates
Yes
Miscellaneous
Extended print modes modified:
No
Very Low Setting (Black Cartridge):
Prompt
Very Low Setting (Color Cartridges):
Prompt
Low Threshold (Black Cartridge):
5%
Low Threshold (Cyan Cartridge):
3%
Low Threshold (Magenta Cartridge):
3%
Low Threshold (Yellow Cartridge):
3%
Store Usage Data&colon;
On Supplies
USB Connection:
No
Font Source:
I (Internal)
Font Number:
23
Font Pitch:
10.00
Font Point Size:
12.00
Symbol Set:
PC-8
Form Length:
64 Lines
Append CR to LF:
No

To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial Forums.
I hope this helps!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Similar Messages

  • Cannot copy or scan from ADF (autofeede​r) on LaserJet 1536dnf MFP

    I've been a very pleased owner of a LaserJet 1536dnf MFP all-in-one printer, scanner, copier, fax. The device is running the latest firmware, it is connected via a hard-wired ethernet connection, and I use it mainly with my laptop which is connected to the same open network via wi-fi. The laptop is running Windows 7 32-bit with the latest drivers, utilities, and diagnostics tools installed.
    The problem I started running into today is two-fold:
    The copier no longer produces copies when feeding one or more pages into the ADF. In other words, the pages are pulled through and the display shows the status as "copying" but no copies are produced. Also, there are no errors indicated on the display.
    The HP Scan utility no longer completes scans via the ADF for one or more pages. Pages are pulled through the ADF then the HP Scan utility presents a simple "An error occured while scanning" error message. I observed similar behavior when attempting to scan via the native windows applications (photo viewer, windows fax and scan, microsoft office document scanning, etc).
    Regular flatbed copying and scanning still works without a hitch for 1 page at a time. I have been using both scenarios above for over a year without any issues. There have been no software installs/updates applied to my laptop in the time these issues surfaced. I have run the print, scan, and network diagnostics utilities from HP and they all show zero problems.
    I have not been able to find any relevant info for either of the issues above via HP support or third-party forums. My hunch is that these are somehow related to a device firmware / hardware / configuration issue and am hoping to find some support via this forum. Appreciate your feedback in advance!
    Best,
    Igor

    This is the side piece that was lifted. The feed tray was removed and I manually ran one page through with the copy button. Then put the feed tray back and affter that i was able to scan multiple pages with no problems.

  • Black page when copying and scanning

    Hi,
    I have a HP Laserjet 1536dnf MFP, all was working fine until I changed the ink cartridge two days ago.  Printing is fine but when I go to copy or scan I get a solid black page printed.  I've checked the light goes across when copying and scanning, tried switching off printer and on again, plugged it straight in to wall and updated all HP software.  Any ideas?
    Many thanks
    Dani

    Hi @Dani77 ,
    I see by your post that you are getting a black page when copying and scanning from the printer. You can print fine and you updated the HP software, the printer is connected directly to a wall outlet and you have the same results.
    I would really like to be able to help you resolve this issue.
    I wasn't sure whether you just updated the printer software on the printer or the firmware.
    If you haven't already, please update the printer's firmware. HP LaserJet Pro M1536dnf Multifunction Printer Drivers.
    Disconnect the USB or Ethernet cable from the printer.
    Make sure the printer is still connected directly to a 3 prong wall outlet.
    Try making a copy with a blank sheet.
    If the output is blank, then try and copy a text document.
    I will send you another step to try in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    How is the printer connected? (USB/Ethernet)
    Please let me know the outcome.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • C5280 prints black page when copying and scanning

    Can anybody help please.
    C5280 prints a black page when I want to copy or scan but it prints ok from the computer. The light seems to be working on it. I am unable to reinstall with the disc as the CD drive is not working now. Does it need to be reinstalled.
    Thanks for any help possible.

    Hi @Dani77 ,
    I see by your post that you are getting a black page when copying and scanning from the printer. You can print fine and you updated the HP software, the printer is connected directly to a wall outlet and you have the same results.
    I would really like to be able to help you resolve this issue.
    I wasn't sure whether you just updated the printer software on the printer or the firmware.
    If you haven't already, please update the printer's firmware. HP LaserJet Pro M1536dnf Multifunction Printer Drivers.
    Disconnect the USB or Ethernet cable from the printer.
    Make sure the printer is still connected directly to a 3 prong wall outlet.
    Try making a copy with a blank sheet.
    If the output is blank, then try and copy a text document.
    I will send you another step to try in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    How is the printer connected? (USB/Ethernet)
    Please let me know the outcome.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Checks just feed through or paper size mismatch on C7250, Bad paper sensors on new printers

    Hi all,
      I have seen these related posts:
    http://h30434.www3.hp.com/t5/Other-printing-questions/Printing-checks-on-officejet-pro-8500/m-p/2460...
    http://h30434.www3.hp.com/t5/Other-printing-questions/B8850-Printing-Problem-on-Canary-print-paper/t...
    http://h30434.www3.hp.com/t5/Other-printing-questions/HP-C7280-rejects-CD-Lables/m-p/246098
    http://h30434.www3.hp.com/t5/Other-printing-questions/CAUTION-DESIGN-FLAW-IN-THE-NEW-GENERATION-OF-H...
    http://h30434.www3.hp.com/t5/Other-printing-questions/printer-won-t-do-labels-help/td-p/233645
    http://h30434.www3.hp.com/t5/Other-printing-questions/HP-Photosmart-Plus-Printer/td-p/233156
    Sorry that there may be many other related posts I only went back one month!  There appear to be MANY problems with newer HP printers and paper sensors with either checks or labels just feeding through or reporting paper size mismatch.
    I have a photo smart C7250 and I have checks that I try to print with Quicken.  I purchase my checks from NEBS a large supplier of pre-printed business forms.
    Sometimes when I print checks they work fine.  Other times one or more just feed through unprinted.  Other times one feeds and the printer displays a paper size mismatch error.
    I also noticed one day when I put the checks in backward by mistake that they all printed fine, so today I decided to look at support for printer paper sensor problems and I found the above listed items.
    I am going to try two things:
    1) placing a blank white label over some of the pre-printed areas of the checks and see if that helps.
    2) Switching back to my old reliable DJ895 for checks if that fails.
    I think HP support should look at this message and the related threads I have found and come out with:
    1) A workaround or software upgrade to bypass the bad paper sensors in many of these printers, my C7250 and the other printers listed in the other threads.
    2) Feed this information back to HP product engineering and QA so that they try colored paper and common pre-printed forms as part of their printer design and testing.  As a design engineer myself, (for another company not printers) I am embarrassed for HP that as a leading printer company they could be so lax in the design and testing of their printers.
    If anyone knows how to get HP’s attention please let me know!
    I hope the rollup of these related threads on check and label printing problems may help you with your problems.
    Thank you,
    James

    I know this is not a timely answer to your post but I just found it while trying to solve the same problem.  Several people have asked the same question but none of them seem to receive helpful replies.
    Maybe you've corrected this problem by now and if so, let me know, but this is what I have decided to do.
    I set aside my cards from the card/envelope set that I purchased from Michaels, bought a package of 8.5 by 11 cardstock.   I printed my message on that, locating it on the page so that I could cut off the right side and the bottom and it was perfectly placed.  If you have not done this before, you will have to score the cardstock at the fold so that it will bend nicely.   They fit perfectly with the envelopes.
    Hope this helps in the future
    Linda

  • My Deskjet HP7610 can't sense the 11 x 17 paper on any of my Acrobat or Photoshop "fit to media" jobs.  Why, after I've set every setting to 11 x 17 do both printer and computer cite "paper size mismatch?

    My Deskjet HP7610 can't sense the 11 x 17 paper on any of my Acrobat or Photoshop "fit to media" jobs.  Why, after I've set every setting to 11 x 17 do both printer and computer cite "paper size mismatch?

    Mandeep5062 wrote:
    Moving to Photoshop Forum
    Try again.

  • When copying raw files from Extreme IV card to hardrive, finder copies a few files then exits task and wipes the card clean of all images.

    When copying raw files from Extreme IV card to hardrive, finder copies a few files then exits task and wipes the card clean of all images.  Have tried new card and card-reader to no avail.  Have done this many times on other macs with no problems.
    Can edit files off the card, in CameraRaw, prior to 'copying' them, ie can 'save as' to the hard drive, so files seem okay on card, before I try to copy them using copy and paste.
    Running OS 10.8.3 on a new macbook pro.

    Rita,
    The process for determining what is causing the files to be corrupt can be a tedious one depending on the following:
    1. Can you review the images on your camera's LCD screen without problems? If not then the problem is most probably either a corrupted/faulty memory card or a faulty camera. If this is the case then your best bet at recovery (of sorts) is to use a program such as BrezzeBrowser from BreezeSys to extract the embedded jpeg versions of the corrupted RAW files from within each RAW file. Chances are, you won't manage to actually repair the corrupted RAW file but the jpegs are better than nothing.
    2. If the images review ok on your camera but are corrupted when viewing on your computer and there seems to be no other problem with other files on your computer then it may be either a faulty card reader or usb/firewire cable between the card reader and the computer that is the culprit. Try the card reader with a different cable and also try a different card reader to determine the cause of the corruption.
    3. If your symptoms are that you get different files corrupting over time when viewing them on your computer then the problem may be any one of either failing RAM memory, hard disk, hard disk controller or IDE/SATA hard disk cables. This is where the troubleshooting can be pretty tedious testing then eliminating each item from the list of suspicious pieces of hardware. Try the card and card reader on an altogether different computer to see if the files transfer correctly to that computer. If so then the problem lies with your computer hardware. If you haven't already done so at this stage, backup all your important data immediately (hopefully you keep backs anyway).
    Hope this helps.

  • Can't shown chinese text when copy & paste data from server to Outlook, Word & notepad, etc.( Office 2013)

    Can't shown chinese text when copy & paste data from server to Outlook, Word & notepad, etc.( Office 2013)

    Hi
    As per the information and details provided by you, when you copy & paste a data from server to Outlook, word, notepad, then you do not receive the Chinese text.
    For Outlook, please follow these steps: -
    Close and reopen Outlook in your western locale (or switch the windows system to your Western locale if you changed that),
    Manually change the message from Western to Chinese encoding, which you can do in all versions up to Outlook 2007.
    If you want to stay in your Chinese locale in Outlook 2007, then:
    After you hit reply, go to the Option tab > More Options.
    In the Encoding drop-down menu, select the Chinese encoding you are working in (Not the encoding used by the person who will receive the message)
    Note:
    To set the Chinese locale in all versions up to 2007 the controls are under.
    Tools > Options. In Outlook 2010 File tab > Options > Advanced > International options.
    Unicode (UTF-8)
    is a good setting for multilingual users.
    Check the
    Auto select 2007)/ Automatically select (2010) encoding box.
    I hope this information will be helpful for you.
    Thanks and regards
    Shweta@G 

  • Hp color laserjet MFP M476dw

    Hi,
    My printer was working earlier this morning but now none of the office computers are able to print any  jobs. I ran a Wireless Network Test report and everything is fine. I also ran a configuration report and nothing shows up as an issue. 

    The heat from your M476 combined with the natural humidity of the laser toner fusing process is sealing your envelopes.  You probally need to find a way to reduce the amount of heat that is being used when printing envelopes.  Normally there are two places to look for configuring the heat.  The first is the pritnt driver itself, which you can switch around with UPDs and different printer languages in hopes that one works better than another.  The other is a print driver configuration for the paper type you are printing from.  For example if you are selecting the Envelope #10 paper size or some custom size.  Each paper type contains commands that the printer uses to heat up and cool down the fuser so that the toner gets properly bonded to the paper. 

  • LaserJet Pro 200 colour MFP M27nw - problem to scan from ADF

    I seem a new LaserJet Pro 200 colour MFP M27nw running on a PC with Windows 8 and have just realised that whenever I scan from the Automatic Document Feeder (ADF), no output file is generated. The original document is drawn into the document feeder successfully and the printer display reports that the scan is ready. However, no file containing the scan is generated. This happens irrespective of whether I send the output to USB or to email and irrespective of whether the original document has single or multiple sheets.
    Interestingly, the ADF works well if I try to produce hardcopies, that is, the printer is able to drawn in the sheets o fthe original document from the ADF (be it single or multiple sheets), and produce hardcopies of the original successfully. Moreover I have no problem to scan single or multiple sheet documents when the original document is loaded through the Flatbed Scanner rather than the Document Feeder Scanner.
    Appreciate any help. Thanks
    Stephen
    This question was solved.
    View Solution.

    HI @StephenScerri ,
    I see by your post that when you scan from the ADF there is no output file containing the scan that is generated to USB or to email. You can copy from the ADF and scan successfully from the flatbed. I would like to help.
    Is this printer the Laserjet Pro 200 MFP M127nw?
    I have provided a document for How to Scan: Windows 8.
    When you scan from the ADF, do you get a scan preview from the computer software?
    Or is it previewing the scan but not saving it to the computer?
    What software are you using to scan with?
    Try saving the scan to the computer, if you are getting a preview, to see if it will save the scan there.
    Please provide in detail the results if you are still having issues.
    Have a great day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • HP LaserJet Pro 100 - scans only from tray, won't scan from adf

    Hi
    I am having issues with my HP LaserJet Pro 100.
    I load the adf and upen the scan dialog however when I click scan, it will scan from the tray every time. I have cleaned the rollers and checked the paper. I have ran scan doctor and it doesn't notice a problem as it doesn't check the adf. 
    There is no error message as it just keeps scanning from the tray even when it is empty and the adf is loaded.
    I have reinstalled the product and tried again but we still cannot scan from the adf.
    I have read several threads which have mispick issues and many threads relating to issue with this particular product yet the help centre IM chat support doesn't have anyone who can assist with this product which i find odd. It doesn't need servicing yet as it isn't very old.
    Please can anyone provide a solution to the problem?
    Thanks
    H

    Hi hayleymariec,
    I see that you are unable to scan from the ADF. I can help you.
    Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector)
    I have provided a document for cleaning the ADF rollers and the separator pad, just to make sure these are the areas you cleaned previously, since you mentioned you already cleaned the rollers.
    'Document feeder mispick' Message Displays on the Control Panel and the ADF Does Not Pick Up Paper o...
    Disregard the title. Both models are pretty similiar for the ADF.
    You must have the Laserjet Pro 100 M175nw. 
    How Do I Find My Model Number or Product Number?
    If the issue persists, I would recommend to call HP Tech Support and inquire about a replacement printer, since you are still in warranty. Call 800-474-6836. If you live outside the US/Canada Region please click the link below to get the support number for your region. Contact HP Worldwide.
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • OS X 10.4.7 server: Samba leaking ram when copying large files from windows

    Hi.
    I'm having problems with:
    Copying files from windows clients to OS X Server 10.4.7 uses up the RAM needed for the files to be copied.
    If I copy a 3GB file, it uses 3GB of RAM
    If I copy a 5GB file, it uses its 4GB of RAM, plus VM.
    If I copy 11GB of files (that is several little files, plus some big by dropping a folder to the share), it consumes all the RAM the machine has, and because of VM paging, whatever other clients are reading from the disk (XRaid) start to have hiccups.
    The RAM of the machine NEVER gets flushed after the copying has finished. So Samba is unusable as it is. I have four Xserves with 4GB of RAM, with 4 XRaids connected each one to each Xserve with its Apple Fiber Channel card and cables.
    I already did the ack=0 thing, got the size of inet.tcp.sendspace and rcvspace to 8388608 and the buffer to 16777216.
    The transfers rates are up to 70MB/s with 2 channel 1gb trunking, and at very sustained rates..
    We are using these to edit video content (DV 25) in Sony Vegas with 2 or 3 clients for each server.
    Any suggestions?
    Thanks very much.
    XServe G5 cluster node (4) / XRaid 7TB (4)   Mac OS X (10.4.7)  

    Michael, I occasionally notice anomolous behaviour when files get dragged between volumes. Mostly the copying window shows an accurate and immediate indication of what's going on, but other times it just looks like nothing's happening, the display never changes, yet, it is in fact copying the files over. Now, if you're copying 2gb files from DVD to HD, it's gonna take some time, more than 5 minutes, so I'm wondering how long you've left it before forcing it to quit?

  • How do i reduce the size of the pdf's scanned from my printer

    i scan from my printer to a pdf.  the file comes across way to big (2mb for 4 pages with no pictures & just text, etc.)  i have already re-set the settings on my scanner / printer to try to get the smallest dpi & image possible.  how do i get to the settings on my adobe acrobat to reduce the size of the pdf when saved on my computer or is this not the right place to do that?

    m spires wrote:
    i have already re-set the settings on my scanner / printer to try to get the smallest dpi & image possible.
    You may need to reset that to use higher scan quality for successful OCR.

  • Error code 8084 when copying large files from VNX servers

    Hi,
    We are experiencing problems when attempting to copy large files from our central VNX servers (EMC) using the connection format of smb://<host>/.  With Mavericks this will be SMB2, presumably.  Anything over a few MB in size fails with the error:
    The operation can’t be completed because an unexpected error occurred (error code -8084)
    Looking in the Console logs we see the following:
    kernel[0]: smb2_smb_read_write_fill: len got reduced, must be running low on credits
    If we attempt this on OS X Mountain Lion or below we have no problems.
    If, with Mavericks, we connect using the format cifs://<host>/ then file transfers work.
    Has anyone come across this before?  Thinking I should also post a bug...
    Cheers,
    Ian
    IT Infrastructure, Open University, UK

    Not helping but others are having the same problem...
    http://discussions.apple.com/thread.jspa?messageID=2564624

  • No access to settl rule when copying Sales order from Quotation

    Hi all
    Can you help me on my following issue :
    I create  quotation in which I refer to a settlement rule.
    WHen creating a sales order in reference to my quotation, the settlement rule in the "item account assignment" tab is not reachable ...
    This mean that all costs are posted on the quotation but not in the sales order.
    But we would like to keep all costs on the sales order, as we do in all our process.
    I've checked the copying rules but found nothing..
    Any suggestions?
    thanks in advance
    martine

    In the standard sales order screen (type OR for example) if you go to Go To Item Account Assignment you can press on the button"Settlement Rule "
    But when copying Sales Information to Sales order with standard copying requirements, you can not presse on the button "settlement rule"
    Furthermore, in this tab, a field called "PC DUMMY" is now appaered on the screen ...??!!!
    Any idea of what to do ??
    thanks !
    martine

Maybe you are looking for