HP LaserJet P1102w not connecting to wireless

We have a fairly new printer, P1102w, only three months old. It is now not connecting to the wireless anymore. I've tried to reconfigure the wireless connection but it cannot find my network SSID anymore. I attempted putting it in manually but no luck. The firmware is up to date so that should not be a problem. Any suggestions?

What is the status of the wireless light on the front panel right now???  Power off printer, power off router.  Power on router and wait 3 mins.  Power on printer and verify it connects to your router.  Status of the wireless light now?
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Similar Messages

  • HP Laserjet P1102W not connecting to wireless network

    Hi,
    yesterday I tried to install my new Laserjet P1102W with wireless capabilities. The first setup went fine and I was able to print wireless from my pc. But when the printer went in sleep mode I had to redo the wireless setup to get it connected.
    So I searched for a possible firmware update on the Ducth HP site, found the lastest firmware (20110826) and followed the instruction to upgrade it. But the upgrade took more than 20 minutes, and th lights on the printer didn't blink. So I pressed the power button again to wake it up, printed a selftest page and did see that the firmware was updated.
    But then the problems started, the printer only gets a 169. ip address while I've setup the wireless correctly (tried manual and automatic setup) while I expect it to get a 192. address. And ofcourse I cannot print anymore via the wireless connection.
    So I tried to find an older firmware to put back on the printer, but with no luck. Also tried to re-apply the latest firmware, but then I get the message that the printer is already up to date.
    Is there a possiblility to force the firmware update to run again? Or can I get an older firmware from HP?
    Best regards
    Rob

    I had the same problem, I was able to connect into my wireless network when I installed the printer (using the CD that came with it) and was able to print but when I turned off the printer and turned it back on  it won't connect to my computer
    and my wireless network.  I did the same thing you did reinstall but get that 169 IP address.  Believe me I was on the phone with the Geek Squad tech for almost 2 hours and the problem was not solved so he told me to just keep the printer on so I don't lose connection.  Same thing with the 1st HP tech support who tried to help me.  He even changed something in my internet security but did not solve the problem at all.  The second HP tech support worked on it too and finally told me that it could be my router.  I have an old Linksys wireless G router so I decided to buy a new router and bought the Netgear N600 WNDR34000v2 and reinstall the printer and everything worked fine.  Also before you install the printer driver be sure to uninstall the printer program (go to Control Panel-Programs and Features) and also disable your firewall because it could also cause problems in the installation.  Now all my 5 computers in my network are using the printer and I can turn it on and off with no problems at all in printing.

  • HP Laserjet P1102W - Not found on Wireless network

    I have a HP Laserjet P1102W.  The  printer is on my wireless network and I am able to use the printer successfully on one computer.  However I am tyring to set up the print on a new computer and it does not see the printer as an available printer...
    The computer that is able to see the printer is right next to the printer that is not.  Help!
    Fran Thompson

    Hello, sorry that you are experiencing this issue. Have you checked to make sure the new computer network is the same as the one the printer is connected to?
    Check the static IP address and see if they are on the same network. 
    **Click the KUDOS star on the left to say 'Thanks'**
    Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

  • Can not connect my wireless printer to the new router.

    Can not connect my wireless printer to the new router.

    Can you please provide details:
    1.  The make and model of printer
    2.  Make and Model of Wireless Router
    3.  Is your printer connection wireless to router or a cable to PC
    4.  What have you done or attempted to do to establish a connection?
    5.  Any further info to assist

  • IPod nano does not connect with wireless earphone via bluetooth transmitters.

    My iPod nano(6th) can not connect with wireless earphone via bluetooth transmitter.
    I want to know which is wrong iPod nano or bluetooth transmitter...Now I tried with i10s because I thought previous one (motolora) might be wrong.
    But both can not connect.

    Sounds good.  Hopefully they can provide you with an accurate answer.
    B-rock

  • IOS7 update failure w/ error "Not Connected to Wireless", but I am connected- How can I update?

    My iPad has the defective "gotofailure" bug in iOS7, but there is only 1 pending update which describes a completely unrelated issue.  I am connected to my Wireless LAN, and that connection works fine.  But, when I try to download and install the pending update (Which may or may not have the major security hole fixed), the update fails with the error message "not connected to wireless".  How can I get someone at Apple support to tell me how to get around this problem?
    What am I supposed to do when the fix for a major bug is blocked by another (apparently minor) update?
    (note:  I am over the 30 day warranty, but within the 1 year warranty.  However, Apple support wants me to pay $20 to have them tell me how to fix their defective software... 
    I expect that the 1 year warranty should apply to defective software, especially this major security bug! 
    This bug completely compromises browser and internet security... it is a HUGE deal!
    see:  http://www.wired.com/threatlevel/2014/02/gotofail/   ).
    This is my first Apple product since the Apple 2E.  If this is the level of customer support and warranty for defects, hardware or software, that Apple provides, it may well be my last apple product. 
    I have worked in customer support at another major computer company, and this type of policy is the surest way to send customers to your competitors that I know of.  Tim Cook, are you listening? 
    (P.S.  Don't bother trying to get the attention of any Apple Executive - they don't want to hear from customers to provide feedback on their products or policies - not by phone nor by email.)
    Any workarounds for the problem or a way to update the iOS7 to fix the security hole will be greatly appreciated. 

    Hi...
    I think here the issue may be that the utility and the internet connection are not getting synchronised. The operating system on your computer is it win XP? If it is win xp, u can use the windows wireless software to manage to your wireless network. In order to use the windows wireless zero configuration, right click on the linksys icon at the bottom right hand corner of the task bar, select the option that says "use windows wireless ....".
    The linksys icon will be grayed and windows will be managing the wireless network. Connect to your wireless network and you should be able to go online.

  • After recent apple update MBP will not connect to wireless internet

    After running recent Security and Airport upgrades my Mac Book Pro (Intel) will not connect to wireless home router supplied by Verizon (GTE) and several public wi-fi's. Cannot get IP but sees networks. My iMac PPC still works fine. Prior to upgrade everything worked fine at home and abroad to other public wi-fi's. MBP still connects at work with AppleBase wireless. Can the upgrade be removed? Is there a simple fix? Should I wait for apple to fix this and break something else.... If not broken don't fix it..

    I'm having similar issues.
    I have 2 MBP's. The newest one is about 1 month old and has never been able to connect to a WPA network. The older MBP is 20 months old and was originally installed with Tiger and gradually updated via Software Update and a retail copy of Leopard and subsequent Software Update updates to 10.5.2. Interestingly, this MBP was always able to access my WPA network until I decided to do an erase and install. I installed the retail copy of Leopard and was subsequently unable to access my WPA network. So, I went back to my Tiger install disks - but I'm guessing that whatever Leopard did *possibly* updated the firmware of the airport card as, even under Tiger, I could not access my WPA network (yes, I agree it seems unlikely that an OS update would/should update firmware but I am grasping at straws).
    Trying to further understand the problem , I noted that the Network utility in System preferences would always show either a connection error or a connection timeout whenever I attempted to join my WPA network. I turned on syslog in my router and attempted to rejoin the network and saw the following errors:
    <150>Apr 30 21:25:17 Vigor: WLAN_DBG - MLME Disassoc MAC 0:1e:ffffffc2:ffffffc0:ffffff9c:3b
    <150>Apr 30 21:25:17 Vigor: WLAN_DBG - MLME Disassoc MAC 0:1e:ffffffc2:ffffffc0:ffffff9c:3b
    <150>Apr 30 21:25:17 Vigor: WLAN_DBG - athgdeauthclient 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:17 Vigor: WLAN_DBG - Wpatimeouthandler
    <150>Apr 30 21:25:14 Vigor: WLAN_DBG - WPA handshake timeout, disconnect 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:14 Vigor: WLAN_DBG - Wpatimeouthandler
    <150>Apr 30 21:25:13 Vigor: WLAN_DBG - send 3rd packet in 4-way handshake
    <150>Apr 30 21:25:13 Vigor: WLAN_DBG - RSN, Send key to: 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:13 Vigor: WLAN_DBG - Wpatimeouthandler
    <150>Apr 30 21:25:12 Vigor: WLAN_DBG - send 3rd packet in 4-way handshake
    <150>Apr 30 21:25:12 Vigor: WLAN_DBG - RSN, Send key to: 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:12 Vigor: WLAN_DBG - Wpatimeouthandler
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - send 3rd packet in 4-way handshake
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - RSN, Send key to: 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - Rx message 2 in 4-way handshake
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - parseEAPOLKey
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - EAPOL_KEY
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - WpaEAPoLhandler, from 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - EAPoL_handler, from 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - send 1st packet in 4-way handshake
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - RSN, Send key to: 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - WPA handshake start for 0:1e:c2:c0:9c:3b
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - WPA2 capable client
    <150>Apr 30 21:25:11 Vigor: WLAN_DBG - MLME Associate MAC 0:1e:ffffffc2:ffffffc0:ffffff9c:3b
    Strongly suggesting that the MBP is not completing the WPA handshake.
    Any ideas as to where my investigations could progress? (The router manufacturer tells me that the WPA timeout handler is not configurable on the router).
    TIA
    Pat

  • Can not connect to wireless networks with ipad 2

    My ipad used to connect to the wireless net at home and in public areas.
    Now all by the sudden it can't "see"  the network.
    Message: " could not connect to wireless network"
    I have tried "everything" also on different networks,
    except resetting the modem.
    My iPhone works, as do all my other computers.
    Modem is Zyxel P2812

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130?tstart=60
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Can't use apps because it says I'm not connected to wireless network

    How do I use apps if it keeps saying I'm not connected to wireless network when I'm connected to wifi and have data connectivity??

    rixxy12345 wrote:
    How do I use apps if it keeps saying I'm not connected to wireless network when I'm connected to wifi and have data connectivity??
    Which apps?
    Click if you want to Thank someone. If Problem is resolved, so that others can make use of it.

  • G410 not connecting in wireless

    I have a G410 notebook model 2049 52q with gemtek wireless lan card.
    I hv installed win xp sp2 with all drivers.  But it is not connecting to wireless router of DLink or Linksys.
    No light for wireless is glowing. While other Lenovo notebook of N series is connecting fine with router.
    G 410 is not connecting with another wireless laptop. It just does not show any wireless network in range
    Message Edited by Rajhans on 09-24-2008 06:05 AM

    To make wireless network working you must match three conditions:
    1) Drivers are installed (no yellow marks in Device Manager)
    2) Hardware switch is ON (it's on right side of notebook, near power chord)
    3) Fn+F5 utility is working.
    Check these please and post back if everything is as described.
    //help will save the world

  • IPad will not connect to wireless

    iPad will not connect to wireless network, keeps trying but will not connect.  Working on our other iPad that has no issue connecting to the same network

    Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    And this - Unplug the charger from the iPad and then replug. May resume charging.
    Or - Recalibrate the battery. See link below.
    The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    What to Do If Your iPad Won't Charge
    http://ipad.about.com/od/iPad_Troubleshooting/a/What-To-Do-If-Your-Ipad-Will-Not -Charge.htm
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Best Practices for iPad Battery Charging
    http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    How to Save and Prolong the battery life of your new ipad
    https://discussions.apple.com/thread/4480944?tstart=0
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    To Extend a Device’s Battery Life, Get to Know It Better
    http://tinyurl.com/b67c7xz
    iPad Battery Replacement
    http://www.apple.com/batteries/replacements.html
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom

  • Ipad will not connect to wireless.  Both connect fine to everything else.  Any suggestions?

    Ipad will not connect to wireless.  Both connect fine to everything else.  Any suggetions?

    Ipad will not connect to wireless.  Both connect fine to everything else.  Any suggetions?

  • My iPad 2 will not connect to wireless.  It recognized the wireless address but when I enter the password it just spins

    My ipad2 will not connect to wireless.  It recognizes our router but when I put in password it just spins.

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at
    http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are drooping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    iPad: Issues connecting to Wi-Fi networks
    http://support.apple.com/kb/ts3304
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.hmL
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Signal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    10 Ways to Boost Your Wireless Signal
    http://www.pcmag.com/article2/0,2817,2372811,00.asp
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How to Change Your iPhone’s (iPad’s) DNS Servers
    http://www.macinstruct.com/node/558
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
    You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • HP LaserJet P1102w Not Working with Mac when connected via USB

    I'm using an old HP LaserJet P1102w - I installed the drivers and the software, and when I connect to my computer, nothing happens. It recognizes the printer, and it says that it's using "Generic PCL Printer" as the driver. The Print Queue has a good time pretending it printed things, and nothing comes out.
    Someone tell me how to fix this POS before I throw it out a window. 

    Hi oprachck,
    I see by your post you are having some issues printing from the Mac. I can help you, but I will need some more information.
    The driver  "Generic PCL Printer", wouldn't be the correct driver using the Laserjet P1102w.
    If you are using 10.8 or 10.9, the drivers are installed by the Apple Updates.
    OS X v10.9 Mavericks: Installing and Using the Printer on a Mac.
    If you are using 10.7 or lower the drivers can be downloaded from this link.
    HP LaserJet Pro P1102w Printer Drivers.
    Check the driver name that is installed for the printer. Make sure it shows just the printer's name.
    Click the Apple menu and then click System Preferences. Click Printers & Scanners, highlight the printer name on the left side and on the right side of the screen should show the name.
    If the full printer name isn't listed correctly, delete it and add the printer name back in from the list. Click the - sign to delete the driver and then click the + sign to add the driver, might have to click the drop down to select the printer's name to add it in.
    What operating system are you using? Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
    How is the printer connected? (USB/Wireless)
    Please provide in detail the results if you are still having issues.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Macbook Pro/Snow Leopard, new HP Laserjet p1102w not finding wireless conn

    It states the installation software only works on Windows...however the drivers are installed on my Mac. I was told this printer would work on my wireless system with a mac. If I cannot install the software on a mac though, doesn't look like it is going to work at all since I cannot access the software settings. 
    The printer works connected via USB but will not connect wireless.....Am I screwed?

    Did you download and install this software?
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

Maybe you are looking for