Hp laserjet p1102w: wireless not working: unable to change to new network

I just moved and established a new wireless network to which I want to connect my printer.
I have followed instructions on HP's websites.  All goes well until I attempt to open "html config..." on the printer utility screen.  nothing happens after selecting "html config...". 
printer works fine if connected via usb; doesnt work wirelessly from laptop, iphone or ipad.   I would like to continue to use the laserjet wirelessly.
any suggestions are appreciated!

"OK let's try this again.  What is the make and model numbers of all you network equipment?  How is everything connected?  OS of computers?  Please explain."
Make & model #:
printer:   hp laserjet p1102w
cable modem:   arris dg860
I am printing from a macbookpro (OS X 10.6.8), iphone 5c and an ipad.
the wireless printing worked just fine from the laptop, my iphone and ipad while at my previous address where I shared a wifi with roommates.  I now have my own wifi via cable (tv) that has a different name than the previous wifi.
this printer currently only prints via USB. the wireless printing doesnt work from any device. 
messages:
laptop:     printer offline
iphone:   no airprint printers found
ipad:        no airprint printers found

Similar Messages

  • HP laserjet p1102w does not work with Mac computer version 10.8

    since i upgraded my Mac to 10.8 operating system, I am not able to use the ePrint function from my HP Laserjet P1102W printer. I was told that the current version of the firmware 20130213 does not support this function. Does anyone know when the new version of the firmware will be available to support this function? thanks much.
    This question was solved.
    View Solution.

    Manual, Please let me know the outcome.

  • HP P1102W Wireless not working

    I've been using this printer about a year. Wifi problems have occured about 2 times.
    I always factory reset, and reconfigured everything through USB.
    but not this time, 
    I factory reset my printer last night, but I can never access to the config HTML page through IP address.
    I can still change the setting through USB, but it doesn't seem to take my changes, and I can't remote print it anymore.
    not through wifi, nor bonjour, and airprint is not working at all.
    I wonder if someone here can solve my problem. 
    Deeply thanks in advance.

    Have you done any firmware or software updates recently?
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

  • Volume button on iPad 1 not working unable to change volume even in settings or when listening to music

    Volume button not working on my iPad. Have tried reset but still no joy. Also have checked that the mute function.

    I have the same issue and I don't have a place to enter a user name. So how did you change your user name? This problem is only on my iPad it did not follow my iPhone. It happened right after updating to  IOS 7.1.1 and now I can't use Facebook for anything on my iPad. I have not changed my login on Facebook. Very frustrated.

  • Wireless internet not working on my mac for new network..

    Im visiting my boyfriend and for some reason my macbook wont pick up his wireless network. All other pc computers in the house seem capable apart from mine. I usually use wireless via my airport router at home. Here it's Tiscalli.
    At first it asked me for the WEP password as normal but when I entered the correct password it would say 'connection failed' after trying to connect via that password. (this still sometimes happens)
    Then both the desired network and other local networks kept being recognised and disappearing intermittedly (This is still happening) When on the pc laptop the network wireless signal for all remain constant. Often it would also show local networks but not the desired one for the house.
    Occasionally it would log me on to the desired network without a password required and show varying levels of signal but the actual internet browser wasnt detecting a connection and was unable to load pages. I also tried another browser - same problem. When it does this, in Network system preferences under 'Connected,' it says 'Airport is connected to SpeedTouch266FC2 and has the IP address (then numbers) Prior to that - it said that Airport had a self assigned IP address and may not be able to connect to the internet (or something similar)- that message went away and was replaced with the former after I changed the ip address section as detailed below.
    Now mostly when I click on the network name - SpeedTouch266FC2 = it makes the system preferences window freeze on the lil rainbow wheel and shows 'application is not responding' in the dock so I have to force quit.
    Ive had a scout round the net - someone suggested entering a web address on your browser that dealt with internet settings but didnt require a connection. http://192.168.1.254 amongst other similar addresses that could work. This didnt work - but not in the normal way for the browsers - instead of address not found, itd come up with took too long to respond or connection failure.
    I also tried (as suggested on another forum) changing the TC/IP section settings from 'DHCP' to Manually, entered the suggested numbers from a forum - IPv4 Addres - 192.168.1.110, Subnet Mask - 255.255.255.0, Router - 193.168.1.1, Configure IPv6 - Off. Ive absolutely no idea what all that means but it did nothing.
    The rest of the laptop works normally

    Not quite sure why you posted in the iPod nano forum?
    Maybe the MacBook forums would be better?
    http://discussions.apple.com/category.jspa?categoryID=218
    Or an Airport forum?
    http://discussions.apple.com/category.jspa?categoryID=140

  • Mail not working when connected to a new network

    Whenever I connect to the network at work I can't send mail. I can receive mail though. I can't use my airport at work. Could this be the problem?
    Thank You
    Tamara

    Unless your employer has a wireless router and wireless network, you can't use Airport when at work.
    Assuming you have a business email account provided by your employer, you can't send mail with your business email account either when connected to your employer's network and internet access at work?

  • HP Laserjet Pro 1102w Wireless (Not working on MacBook Air 10.10)

    HP Laserjet Pro 1102w Wireless is not working on my MacBook Air Yosemite (v10.10).
    I tried setting it up via this link: (v10.10 Yosemite, Method 3: Wireless Setup Using a USB Connection)
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02847467#N2251
    All I get under printers is the USB kind and NOT the Wireless/Bonjour kind.
    Can anyone help me out?
    Thanks.  

    Hi @Random_Pelican ,
    I see that you are having issues setting up the printer on 10.10. I would like to help you out today.
    If the printer has a valid IPv4 address and you still can't add the printer as a Bonjour printer, most likely Multicasting is turned off on the router, since your not able to add the printer as a bonjour device and the other devices won't recognize the printer. Just call the router company and have them turn it on.
    If the printer doesn't have a valid IPv4 address please try these steps:
    Reset the printer first to clear out any previous network settings.
    Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
    Print out a configuration report and make sure the SSID and IP address are cleared.
    Printing a Configuration Page.
    Make sure Safari is set as the default browser. Sometime the Embedded Web Server won't open if it isn't.
    Open Safari, across the top select the Safari menu, select Preferences, General, set as default.
    I will provide the steps for 10.9, which should work the same for 10.10.
    Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
    Here is a Youtube video of the Laserjet P1102w wireless installation on Maverick.
    Laserjet P1102w.
    You may follow the steps instead of watching the video.
    You have to connect the USB cable from the printer to the computer to install the printer as a USB device first and then configure the wireless network.
    Turn the printer on, connect the USB cable and install the Apple Update that should automatically load.
    Then go to the Apple, System Preferences, Printers and Scanners.
    Highlight the Laserjet on the left side of the window.
    Then click on Open Print Queue, click on Settings, click on Utility, click on Open Printer Utility, then click on the HTML Config button.
    The Embedded Web Server for the printer will open.
    Click on the Networking tab, select Wireless on the left side.
    Fill out this information for your network. Status make sure you select Enabled.
    Apply the settings.
    Then go back to Apple, System Preferences, Printers and Scanners and click the + sign to add the Laserjet bonjour printer. (might take a couple of minutes to appear) Make sure the printer listed beside use: shows the proper printer name and not the default driver, then click on the add button.
    Delete the USB printer from the list from the Printers and Scanners window.
    Disconnect the USB cable.
    Test the printer.
    Let me know how you make out.
    Have a great day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Intel 6205 wireless not working with Lenovo W520

    Loving the new W520... very fast, if only the wireless would work. Unable to get wireless interface functioning, won't even show up in ifconfig. I've appended requested wireless information, thanks in advance for any assistance.
    1) Machine Brand and Model (PC/Laptop):
    Lenovo W520
    Intel Centrino Advanced-N 6205
    Note: Wireless switch on lefthand side enabled, bluetooth led lights up but wireless does not.
    2) Wireless Brand, Model and Wireless Chipset:
    $ lspci -nn
    03:00.0 Network controller [0280]: Intel Corporation 6000 Series Gen2 [8086:0085] (rev 34)
    3 ) check interface:
    ifconfig does not show wireless
    $ iwconfig
    lo no wireless extensions.
    eth0 no wireless extensions.
    4 ) Check for modules:
    $ lsmod
    iwlagn 215351 0
    iwlcore 139688 1 iwlagn
    mac80211 269644 2 iwlagn,iwlcore
    cfg80211 167809 3 iwlagn,iwlcore,mac80211
    5) Kernel boot messages
    $ dmesg
    [ 13.497936] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
    [ 13.497938] iwlagn: Copyright(c) 2003-2010 Intel Corporation
    [ 13.498058] iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 13.498089] iwlagn 0000:03:00.0: setting latency timer to 64
    [ 13.498181] iwlagn 0000:03:00.0: Detected 6000 Series 2x2 AGN Gen2a, REV=0xB0
    [ 13.499187] lp: driver loaded but no devices found
    [ 13.502642] alloc irq_desc for 22 on node -1
    [ 13.502645] alloc kstat_irqs on node -1
    6 ) Network configuration
    $ sudo lshw -C network
    *-network UNCLAIMED
    description: Network controller
    product: 6000 Series Gen2
    vendor: Intel Corporation
    physical id: 0
    bus info: pci@0000:03:00.0
    version: 34
    width: 64 bits
    clock: 33MHz
    capabilities: pm msi pciexpress cap_list
    configuration: latency=0
    resources: memory:d5300000-d5301fff
    7 ) Scan for networks:
    not relevant as no wireless interface appears
    8 ) Ubuntu Version:
    Ubuntu 10.10
    9 ) Kernel/architecture (including 32 vs. 64 bit):
    2.6.35-28-generic x86_64
    10 ) Restarting the network:
    sudo /etc/init.d/networking restart
    * Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.
    [ OK ]
    Additionally, modinfo shows the following:
    $ modinfo iwlagn
    filename: /lib/modules/2.6.35-28-generic/updates/compat-wireless-2.6.36/iwlagn.ko
    alias: iwl4965
    license: GPL
    author: Copyright(c) 2003-2010 Intel Corporation <[email protected]>
    version: in-tree:
    description: Intel(R) Wireless WiFi Link AGN driver for Linux
    firmware: iwlwifi-4965-2.ucode
    firmware: iwlwifi-5150-2.ucode
    firmware: iwlwifi-5000-2.ucode
    firmware: iwlwifi-6000g2b-4.ucode
    firmware: iwlwifi-6000g2a-4.ucode
    firmware: iwlwifi-6050-4.ucode
    firmware: iwlwifi-6000-4.ucode
    firmware: iwlwifi-1000-3.ucode
    srcversion: 8F7F4C6196599FCA596C837

    Hi  sparhk, and welcome.
    One of the Lenovo staff who frequents the forum put out a call to help you in a private forum.  I do a little Linux, so I poked into it.  To my amazement my first Google hit was your thread where you indicate you have solved the problem.  (At least, it _looks_ like you...)
    May I respectfully suggest that a post back here indicating success would be a nice touch?  That way anyone who passes by looking for help with this issue will have a better chance of finding it.  For posterity, here it is (see post number 25):
    [SOLVED] Intel 6205 wireless not working with Lenovo W520
    Glad you got it working,
    Z.
    The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc.  The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • HP Laserjet P1006 is not working on Windows 7 (64-bit).

    I lost my original CD-Driver and I tried to download the CD-Driver on HP website but it doesn't work when I click printing.  It seems that my HP Laserjet P1006 is not working on Windows 7 (64-bit).
    Can anyone give me a link that works for installing driver for HP Laserjet P1006 for Windows 7 (64-bit)?  
    Thanks for helping!

    Hi @achieverone ,
    I can help you with finding the drivers for the Laserjet P1006.
    Just to clarify, you were able to install the printer software, but it just isn't printing correct?
    Here are the two drivers available for Windows 7 64 bit.
    HP LaserJet P1000-P1500 Hostbased Plug and Play Basic Driver.
    HP LaserJet P1005/P1006/P1500 Printer Series Full Feature Software and Driver.
    Try and print a hardware self test on the printer to find out if it is a hardware or software issue.
    Open and close the lid five times quickly. It should print off a page with black lines on it.
    Download and run the Print and Scan Doctor. It will diagnose the issue and might automatically resolve it. Find and fix common printer problems using HP diagnostic tools for Windows?
    What were the results when you ran the Print and Scan Doctor? (did it print or scan, any error messages)
    If you need further assistance, just let me know.
    Have a great day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • S10-3t bluetooth and wireless not working with windows 8

    S10-3t bluetooth and wireless not working with windows 8. I tried everything but doesn't work at all. I don't know where to find the new drivers that are comatible with windows 8 ???!!! please help me to solve this problem because i tried everything....

    Do you still have your windows7 install files ? 
    ( installation image is usually in LENOVO_PART OKRBackup/Factory ) ? I lost them :\
    if yes I fear you have to enable it in win7 and then use it in win8
    http://rzr.online.fr/q/lenovo# g470 s103t (Please Contact me if your s10-3T is booting win7 or support bluetooth, 3g)
    Lenovo S10-3t | Model Name : 0651 | Mfg Date: 2010/06/08
    Lenovo G470 | Model Name : 20078 | M fg Date: 11/03/23 | BIOS: 40CN23WW(V2.09) 06/20/2011 | CPU: i5-2410M | Linux version 3.3.4lenovog470+ (root@lap) (gcc version 4.6.3 (Debian 4.6.3-4) ) #8 SMP Tue May 1 10:23:48 CEST 2012
    OS:GNU/Linux/Debian

  • Wireless not working - help!

    Hi - I lost electric today and when I got home, wireless is gone.  I have powered down and up again, wireless still not working.  I can see other networks but not mine.
    I can hardwire to my computer to get on the internet but don't know how to restore the wireless again.
    Can someone help me?  I've been waiting on hold on the phone for an hour now...

    Seems that you lost your wireless configuration.  Easy to fix, but your best bet would be to connect (hardwired) like you are, connect with live chat and let the technicians take over your computer-they will tell you how. 
    Or you can download the instructions from this site and follow them step by step.  Just choose your product and select the PDF document.

  • Wireless not working, iPhone 4S, upgraded to OS6, any suggestions?

    wireless not working, iPhone 4S, upgraded to OS6, any suggestions?

    Take the troubleshooting steps recommended in the User Guide.

  • HP Laserjet 3052 Scanner not working

    So I upgraded to Leopard and everything seems fine except I cannot run the HP Scan software. The printer [art still works but I just cannot scan. I have tried reinstalling the software but it still not working. HP have no new software and drivers for it yet.
    Anyone any ideas?
    Thanks,

    I can confirm what everybody else in this thread has said and add one detail. I bought an HP 3055 all-in-one yesterday and after installing the software, not only wouldn't it scan ("waiting for PC..." forever) but it also wouldn't print, AND another HP printer elsewhere on my network STOPPED working.
    After an hour on the phone with HP support (10 minutes just to register my info), the guy confirmed that there is no 10.5 driver, didn't know when there would be one, and added the following amazing fact. Not only does the software on the CD that comes with the printer/scanner not work with 10.5, it actually BREAKS its printing from Leopard (and similarly the 10.4 or earlier downloadable drivers from hp.com). He claimed that printing from 10.5 works on the 3055 out of the box, but if you are so reckless as to install the software that actually came with the printer, it permanently stops working. (Plus, apparently, stops the printing of other HP devices.)
    He went on to say the only fix was to re-install the Mac OS . However, I can report that after un-installing every piece of HP software on my machine (using their uninstallers, not just deleting), then restarting, the printer now works, and so does the other HP printer on the network. (Scanning still doesn't work.)
    Btw, echoing other complaints on this thread, the reason I bought a new HP scanner was because my old one had stopped working ever since (I think) 10.4, and I finally gave up.

  • I turned of iMessage and now I want it back on and it's not working, I have changed my password and now I don't know what to do. Is there something obvious I am doing wrong?

    I turned of iMessage and now I want it back on and it's not working, I have changed my password and now I don't know what to do. Is there something obvious I am doing wrong? I have done this on both of my iPads and it hasn't let me go back on to iMessage on either of them.

    iCloud System Status
    Current
    iCloud: iMessage - Users Affected: Some
    11/18/2012 13:34 PSTUsers are unable to use iMessage. Normal service will be restored ASAP.
    iCloud: FaceTime - Users Affected: Some
    11/18/2012 13:33 PSTUsers may be unable to place FaceTime calls. Normal service will be restored ASAP.
    http://www.apple.com/support/icloud/systemstatus/

  • Problem with new version 4.3.2 apps not working " after update to the new version "

    Problem with new version 4.3.2 apps not working " after update to the new version "
    i was in 4.3.1 then i do the update , but now after update i face this problem , so what i Supposed to do ?!!

    Hi There
    Had the same problem as you. App would terminate when launched.
    Solution to working You Tube app:
    -Go to playstore
    - Uninstall app (it doesn't remove the app, only removes the update)
    - "Et Voila", working again.
    This doesn't correct the problem, it's just a workaround for you to be able to use youtube app again.
    Hope it helped.
    Best Regards

Maybe you are looking for