HP Laserjet p2035n Can't set DHCP

Hello I have a HP Laserjet p2035n connected via a switch to a LAN. The printer had a static IP address configured, and handled print jobs from connected PCs with no problem till yesterday.
The printer stopped responding to print jobs sent accross the LAN. Also, I was unable to access the web admin interface for the printer. I decided to reset it to factory settings and reconfigure it from scratch. I powered off the printer and held down both the GO button and the CANCEL button while powering the printer back on. The indicators all flashed in unison signalling that the printer had been reset.
When I printed a configuration page however, it indicated that the printer was still in manual IP configuration mode with an IP of 0.0.0.0 meaning that it would not pull a temporary IP from my DHCP server. Sure enough, I was unable to access the printer web admin interface after the factory reset.
I tried upgrading the firmware, I tried installing the HP software on my laptop to see if there was a setup programme that would reconfigure the printer ... I tried connecting directly via USB and successfully printed a few pages.
Can someone tell me if there is a way to reset the network connection mode of the printer back to DHCP, perhaps using the buttons on the printer, or some tool that I can download.
Thank you for any help that you could offer.
ELMKD

Hello:
Thank you for your response. I resolved the problem.
A static IP was reserved for the printer by my DHCP server.
The printer experienced a duplicate IP error on the LAN which was not indicated on the configuration page.
The printer was returned to factory default, but could not complete the initialization process (it is unclear why).
Network Information showed the following:
Status = Initializing
Host Name = ...
IPv4 Address = 0.0.0.0
IP Subnet Mask = 0.0.0.0
IP Default Gateway = 0.0.0.0
IP Configured By = Manual
etc...
This meant that the EWS could not be accessed, and the printer would not pull a new IP via DHCP.
Solution
1. Return printer to factory default by powering off, and holding down both CANCEL and GO buttons while powering on.
2. Ensure that there are no IP address conflicts on the network affecting the printer.
3. You may have to connect the printer to a separate subnet to get it to fully initialize and pull a temporary IP via DHCP
4. Print a configuration page by holding down the GO button for 5 seconds and verify that you have a new IP
5. Access the printer web admin page via the new IP and reconfigure the printer as needed. Static IP etc.
I hope that this helps someone else who might be confounded by this problem.
Regards,
Elmkd

Similar Messages

WRT54G....Can I set DHCP to use the router for DNS instead of external DNS?

Hi folks. I cant' get my router to have DHCP tell my PCs that the router should be the DNS server instead of the external servers it is using. I am using Comcast Cable internet. It sets the external DNS servers for every PC that connects to it and I have problems finding my PCs on my network by NetBIOS name because the external DNS servers obviously don't store my local PCs. How can I set the router up to set DHCP to use the router for DNS?

If you cannot set the DNS server in the configuration page for the DHCP server in your router then your router does not support this.
This won't solve your problem though. The DNS server on the router is a simply forwarder. It simply forwards the DNS requests from your computer to the ISP's DNS servers. The DNS server does not accept dynamic updates to a private zone inside your LAN. And DNS is pretty much unrelated to the standard windows workgroup browsing which does the actual name resolution inside your LAN. That name resolution even works without a router inside your network. Basically all windows computers in your network periodically broadcast their name to the network. One windows computers is elected "master browser" which collects all these names and provides the name resolution service for all computers in the workgroup.
If this does not work it is most likely a windows configuration problem. It could be a software firewall on the computers which blocks traffic. It could be that the computers are not setup for file/printer sharing and thus have the computer browser disabled. It could be that your computers have a WINS server configured which does not exist. There are probably more causes. The better source to ask this question would probably a Microsoft support group. They deal with these kinds of issues more often and maybe a MVP may be able to point you into the right direction or give some links to step-by-step instructions...

Hp LaserJet 5200 can not set IP manualy.

Hi!
In my HP LaserJet 5200, field where input IP address (configuration -> JetDirect -> TCP/IP) is empty.
How I can set IP addres?
Thank you!

This printer needs "JetDirect" to operate as a network printer. Or, you would need to set up printer sharing through the computer you have it connected to.
Do you have any of the following on your printer?
, optional Connectivity
for HP LJ5200
HP Jetdirect 175x Fast Ethernet Print Server (J6035G), HP Jetdirect en3700 Fast Ethernet Print Server (J7942G), HP Jetdirect 620n Fast Ethernet Print Server (J7934G), HP Jetdirect 625n Gigabit Ethernet Print Server (J7960G), HP Jetdirect 635n IPv6/IPsec Print Server (J7961G), HP Jetdirect ew2400 802.11g Wireless Print Server (J7951G)
If your model is not network ready, you'd need to buy a print server.
For wireless connectivity, you might take a look at Apple's Airport Express, which allows a USB printer to be plugged in to it, and then wireless connectivity from network computers, that are wireless capable.
If you've had wireless connectivity with this printer before, then you should be able to access it from the computer it's attached to, I'd think, by going to printer settings, and configuring from there.
Sorry I can't be of more help, as I've not had personal use of that particular model. Maybe someone will chime in.

My LaserJet P1102 can't set as default

I'll have try every suggest from other source about that problem. but can't print from Microsoft Excel. Other program such a microsoft word can be done.
Please help me. i'm very confused.

Hi,
Such an issue as described is a problem with the operating system and related with the user account permissions, a such is not an issue with the printer driver itself.
Follow these steps to repair the user permissions, be aware that those involve registry values editing and should be done carefully. you may do so at your own risk, it is safe as long as you follow the steps exactly as it.
Be sure to follow the steps exactly as listed and be caution as any wrong action can affect the operating system.
Step one: Create a restore point:
Follow these steps to create a resore point to avoid any possible problem:
http://support.hp.com/us-en/document/c00034790#c00034790_createrestorepoint
Step Two: Backup the Registry values:
Click the Start button and select Run.
Type regedit into the bar and press OK.
Right ciick on My Computer and select Export.
Save it on the desktop as a backup prior making any changes.
Step Three: assign full permissions to the Windows path
Expend HKEY_CURRENT USER
Expend Softwre
Expend Microsoft
Expend Windows NT
Expend CurrentVersion
Right click on Windows and select Permissions.
Select your user account if listed and be sure to select Allow within the Full Control column
Note: if your user name is not listed press on Add, type your user account name and press on Check. select it and then assign it Full Permissions.
Select Everyone if listed and be sure to select Allow within the Full Control column
Note: if Everyone is not listed press on Add, type Everyone and press on Check. select it and then assign it Full Permissions.
Once both your user and everyone have full control assigned press on OK, the Registry editor appears.
Step Four: Restore the default printer value
Once the paths above are listed on the left pane, on the right pane you will see additional values for that folder.
From the right pane right click on Device and select Modify.
Remove any listed information and paste the following value into Value Data, be sure to include any character exactly as listed i the box below:
winspool,Ne00:
Press ok to confirm, reboot your PC and try setting a default printer again, then try printing from Excel.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

10.3.9 - 10.4 Migration failed! Server lost! - How to set DHCP info?

Today we tried to migrate our Xserve from 10.3.9 to 10.4
We've chosen to start the update from a PowerBook and attached our Xserve in FireWire Target Mode.
Update/Install ran smoothly, BUT ON RESTART WE LOST CONTACT TO OUR XSERVE
In system.log it says
HeadlessStartup: Enabling root account so we can remotely administrate.
Apr 5 14:03:18 everlearn /System/Library/ServerSetup/serversetup: defaults info /usr/bin/defaults write -g AppleLanguages '(de, English, ja, fr)'
Apr 5 14:03:20 everlearn /System/Library/ServerSetup/serversetup: CFUserTextEncoding info 0:3
Apr 5 14:03:22 everlearn /System/Library/ServerSetup/serversetup: user library preferences ByHost folder is existed.
Apr 5 14:03:22 everlearn /System/Library/ServerSetup/serversetup: copyPath from rootByHost to userByHost failed.
Apr 5 14:03:22 everlearn /System/Library/ServerSetup/serversetup: create file userByHost is OK.
Apr 5 14:03:25 everlearn mDNSResponder: Service "everlearn.ssh.tcp.local." renamed to "wipaed-dev"
Apr 5 14:03:25 everlearn mDNSResponder: Service "everlearn.sftp-ssh.tcp.local." renamed to "wipaed-dev"
Apr 5 14:03:47 everlearn sudo: root : TTY=unknown ; PWD=/ ; USER=cyrusimap ; COMMAND=/usr/bin/cyrus/tools/mkimap
Apr 5 14:03:55 everlearn root: Setting SquirrelMail language to 'de_DE'
Apr 5 14:03:57 everlearn sudo: root : TTY=unknown ; PWD=/private/var/imap/db.backup2 ; USER=cyrusimap ; COMMAND=/usr/bin/touch /var/imap/db/skipstamp
Apr 5 14:03:57 everlearn sudo: root : TTY=unknown ; PWD=/private/var/imap/db.backup2 ; USER=cyrusimap ; COMMAND=/usr/bin/cyrus/bin/ctl_mboxlist.old -d
Apr 5 14:04:00 everlearn sudo: root : TTY=unknown ; PWD=/private/var/imap/db.backup2 ; USER=cyrusimap ; COMMAND=/bin/mv /var/imap/mailboxes.db /var/imap/mailboxes.db.old
Apr 5 14:04:00 everlearn sudo: root : TTY=unknown ; PWD=/private/var/imap/db ; USER=cyrusimap ; COMMAND=/usr/bin/touch /var/imap/db/skipstamp
Apr 5 14:04:01 everlearn sudo: root : TTY=unknown ; PWD=/private/var/imap/db ; USER=cyrusimap ; COMMAND=/usr/bin/cyrus/bin/ctl_mboxlist -u
Apr 5 14:04:01 everlearn ctl_mboxlist[942]: skiplist: recovered /var/imap/mailboxes.db (0 records, 144 bytes) in 0 seconds
Apr 5 14:04:05 everlearn /System/Library/ServerSetup/MigrationExtras/49_webconfigmigrator: Existing /private/etc/httpd/httpd_macosxserver.conf file couldn't be read! Nothing to migrate.
Apr 5 14:04:05 everlearn /System/Library/ServerSetup/MigrationExtras/50_ipfwconfigmigrator: No Jaguar firewall settings to migrate from NetInfo directory dsRecTypeNative:/config/IPFilters.
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:Migrating old IP address group. New name:'Migrated: 10-net' New id:'Migrated: 10-net'
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'SSH - Secure Shell' enabled because 'ssh' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'Server Admin SSL, also Web-ASIP' enabled because 'asip-webadmin' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'Remote Directory Access' enabled because 'remoteda' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'Server administration using Server Admin' enabled because 'serveradmin_pseudoservice' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'ICMP - echo reply messages (replies to outgoing pings)' enabled because 'icmppingpseudoservice' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'IGMP - Internet Group Management Protocol' enabled because 'igmp_pseudoservice' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'RTSP - QTSS streaming' enabled because 'rtsp' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'WebObjects' enabled because 'webobjects' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'QTSS web administration' enabled because 'qtssweb_pseudoservice' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'QTSS MP3 streaming' enabled because 'qtssmp3_pseudoservice' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'HTTP - web service alternate (Apache 2 default)' enabled because 'http-alt' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:IP address group 'any' has 'HTTP - web service' enabled because 'http' was enabled in old rules
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:Migration applying old customized enable status to rule '65000'
Apr 5 14:04:09 everlearn /System/Library/ServerSetup/MigrationExtras/60_ipfwconfigmigrator: ipfw config migration:Notice:Migration applying old customized enable status to rule '63300'
Apr 5 14:04:09 everlearn root: The previous /etc/httpd/workers.properties file has been saved as /etc/httpd/workers.properties.applesaved. The current /etc/httpd/workers.properties file now includes a blojsom worker.
Apr 5 14:04:31 everlearn servermgrd: cupsd mach_msg error (ipc/rcv) timed out
Since then we cannot find the Xserve via ping or even with a PowerBook in the same subnet.
How can we restore TCP/IP information, subnet info etc.
Right now we CANNOT ACCESS PER SSH but ONLY VIA FIREWIRE ACCESS, therefore we cannot use changeip and serversetup.
How can we set DHCP information without ssh access only access to the files?
What to set?`
Where to set?
Any information is greatly appreciated.
karsten

The main ethernet port had been disabled by the installer!
We connected a powerbook (just plain ethernet cable) to the other port which was running with some old ip number and send
ping 224.0.0.1
This gives you the ip number
then we logged in via ssh
then
networksetup -setnetworkserviceenabled "Ethernet…" on
Now we can work through the messed up install…

Can i set up airport to be dhcp on a static network?

I have a static network at work and would like to open my internet up to our customers. MY question is how can I set up a apple airport ( or multiple we have a large area) to assign DHCP addresses to customers via WYFY
I was thinking something like this:
Modem -> Router -> Airport -> Wireless DHCP
                  |
                  |
                 V
            Work PC's Static Ip's
It would be a requirement that the wireless connections were on a seperate network that could not see any of the work PC's
Thanks,
Ryan Cooper

Modem -> Router -> Airport -> Wireless DHCP
                  |
                  |
                 V
            Work PC's Static Ip's
It would be a requirement that the wireless connections were on a seperate network that could not see any of the work PC's
Everything depends on the router ..
If the router offers vlan.. then you can set the airport to a different vlan than the Work computers and it will work fine.. But your setup currently is such that wireless clients behind the airport even if they get a different IP address range would still be able to access the work PC's.
Another possible method is to use secondary IP address in the router.. this is same idea as vlan really but some routers offer IP alias.. or secondary IP.. it has a number of names.. This would not fully protect the computers on the main IP address range but via firewall in the computers will effectively do so. It would be important to make sure the local firewall is setup and running.

How do I connect a network printer to ipad 3. I have a HP LaserJet P2035n. It is a network printer. Not Wireless.

How do I connect a network printer to ipad 3. I have a wireless router on my LAN. I have a HP LaserJet P2035n which is a network printer and it is connected to the LAN. The printer is not on the AirPrint list. The printer is not wireless.

Hello,
I am using a Mac with this router. Any ideas how I can set it up to print wireless. Im not a tech person so this gets confusing for me sometimes.
Thanks!

Network drivers for Laserjet p2035n

I'm setting up a Laserjet p2035n networked printer on a Windows 2003 server, that is already set up on another computer.
I have the IP address and create a new standard TCP/IP port but the HP website only has USB drivers (even for the N). I just need plain network drivers.
Please Advise.
This question was solved.
View Solution.

Hi,
You may either use the standard Plug and Play drivers by running the installation, then terminate it and add the printer through the Windows have a printer dialog. the software can be downloaded from here:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18...
Select Add a Printer and follow the steps by creating a Standard TCP/Ip port by providing the printer IP address.
Follow the steps till the model selection is listed.
Click Have Disk and browse to C:\Program Files\HP\HP LaserJet P2030 Series (May also be listed under Program Files (x86) for 64-bit OS), from there select the displayed INF file and select your printer.
Follow the steps to complete the wizard.
For standard network installation you may use the full software below:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18...
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Can I set 1 laptop wireless connect with static IP to WRT610N?

I have a WRT610N with 3 PCs wired and various wireless devices accessing. 1 of the wireless devices, running Windows 7, needs to run a static IP. Do/Can I set this up in the router or do I need to do in the PC?

You can use DHCP reservation in the router to assign a fixed IP address to the PC.
Or you can set the static IP address on the PC directly.

Can I send DHCP host name to my ISP from RV220W?

My ISP waits a definite host name from me to return my white IP address via DHCP. Can I set this parameter in RV220W router? I don't find such parameter in IPv4 WAN configuration page.

After firmware update to 1.0.3.5 I can set up router name but provider support answer that router doesn't send its name to provider during DHCP handshake. Is that right?

Can not set the default printer

Hello,
we have HP LaserJet Pro MFP M125-M126 PCLmS network all in one printer, as the installation in every user was successful, and was working fine on installation day, after a day all user facing issue like can not set default pritner , can not print, all user are facing issue at a time,
prompt reply is appreciated,
This question was solved.
View Solution.

Hi @darshan9 ,
I see that you are experiencing issues setting the default printer for users and you are unable to print over the network.
I would be happy to help you.
Do you mean individual computers setup with the printer over the network users or one computer with multiple users?
Do you have Admin Rights on the computer to make changes?
What is the full name and product number of your printer? How Do I Find My Model Number or Product Number?
Download and run the Print and Scan Doctor. It will diagnose the issue and might automatically resolve it. http://www.hp.com/go/tools>Using HP Diagnostic Tools for HP Printers in Windows.
I would suggest you to check if you have a different user account or from an administration account.
I would also suggest you to create a new user account and check if you are able to set the printer as default.
Create a user account. Create a user account.
If you are still having issues run the Fixit Tool. Diagnose and fix printer and printing problems automatically.
What were the results when you ran the Print and Scan Doctor? (did it print or scan, any error messages)
If there is anything else I can help you with, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Can I set up a Lasrejet pro M201-M202dw to use wireless and USB

How can I set up my Lasrejet Pro M201-M202dw to be accessed by both USB and wireless
This question was solved.
View Solution.

Hello @datfr
Thanks for posting on the HP Forums!
I should be able to provide some help. If your LaserJet is already configured on the wireless network and added to the computer then all you need to do is plug the USB cable into the computer too. If the printer is not WiFi yet ensure the USB is no plugged in yet and run the wireless setup for the printers. Here is a link regarding Setting Up the Printer for a Wireless or Wired Network for the HP LaserJet Pro M201 and M202 Printer....
Let me know how it goes!
Cbert
I work on behalf of HP.
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" at the bottom of this post to say “Thanks” for helping!

HP LaserJet P2035n Is support pcl5 ?

HP LaserJet P2035n Is support pcl5 ? you can install HP LaserJet P2035 with pcl5 in windows 7 similar hp laserjet 1320? (I'm sorry, I can not speak perfect English)

Hi,
Please try the following settings:
Right click the printer icon, then click Printer Properties.
Click the Device Settings tab.
At the very bottom, uncheck the Allow Manual Duplexing option.
Now try printing and check for any change.
Please let me know of any change,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Aironet 1240 ag setting dhcp range

How do I set up a dhcp range in the Aironet 1240ag access point? The access point is the dhcp server.

You can only set the DHCP scope on a AP from the CLI, so you would need to get console/telnet/ssh access. After that is the same setup as a router or switch.

I forgot the administrator password for my mac and cant set a new one without it how can i set a new one

i forgot the administrator password for my mac and cant set a new one without it how can i set a new one

Reset Password 10.7, 10.8...
http://reviews.cnet.com/8301-13727_7-20087723-263/how-to-run-the-password-reset- utility-in-os-x-10.7-lion/

HP Laserjet p2035n Can't set DHCP

Similar Messages

Maybe you are looking for