HP LASERJET P3005N NOT PRINTING WITH MANUAL SETTINGS

We have a subnet for our PCs and Thin Clients and we have a subnet for our printers.  The subnet for our PCs and Thin Clients is setup for DHCP service while the subnet for our printers is setup for static addressing.  The HP Laserjet P3005n printer is able to operate effeciently in DHCP mode; it picks up an ip and I'm able to print to it, ping it, etc.  However, it doesn't communicate with the network when I manually configure an address to it; I'm not able to print to it, ping it, etc.  It was working find with the original settings (static ip address) on a Friday then the problem started when the office opened back up on that following Monday.  I've tried different cables, assigning the printer's address to a different printer, different ports, and even installed a JetDirect card into it and it still doesn't fix the issue.....PLEASE HELP!

<Is this because i just upgraded to 10.5.6? </i>
No, probably not. I have no problems printing to my 3015 from 10.5.6.
Is apple going to do something about this?
Doubtful since it's almost certainly not Apple's problem, per se. Make sure you have the latest printer update, HP Printer Update 1.1.1, which should appear in Software Update if you haven't installed it and will probably appear in the "Installed Updates" pane of the Software Update preference. And if course if it's a networked printer you'll want to ping it to make sure that your system is actually reaching the printer.
If you continue to have problems, you'll probably want to take it up with your IT people or with HP. But you can keep an eye on this thread and see if suggestions to the OP would apply in your case as well.

Similar Messages

  • HP LaserJet 3015 not printing with 10.5.6

    I just upgraded from 10.5.5 to 10.5.6 and my HP Laserjet does not print. I removed it and added it back but when I try to print it always gives me the following error when the printer queue is trying to connect:
    Printer busy (status:0xe00002e9)
    Please help.
    HGCali

    <Is this because i just upgraded to 10.5.6? </i>
    No, probably not. I have no problems printing to my 3015 from 10.5.6.
    Is apple going to do something about this?
    Doubtful since it's almost certainly not Apple's problem, per se. Make sure you have the latest printer update, HP Printer Update 1.1.1, which should appear in Software Update if you haven't installed it and will probably appear in the "Installed Updates" pane of the Software Update preference. And if course if it's a networked printer you'll want to ping it to make sure that your system is actually reaching the printer.
    If you continue to have problems, you'll probably want to take it up with your IT people or with HP. But you can keep an eye on this thread and see if suggestions to the OP would apply in your case as well.

  • LaserJet M125a not printing with Windows XP SP3

    Hi everyone.
    Today I bought new printer. I wanted instal this printer on my old pc with Win xp but during installation appears window with warning " software for this device: "printer" has not passed compatibility testing with windows xp system". Nonetheless installation is going to end. After all I can only copy and scan. When I try print something, it looks as if the print process is working, nothing happens and there isn't list of not printed items. I have installed printer on my laptops with Win 7 and Win 8.1 and everything is fine.
    Sorry for my grammatical mistakes. I have to translate this from polish
    I hope someone can help me solve this issue. A lost all day to find any solutions ;/
    Regards
    Karol
    This question was solved.
    View Solution.

    Hi @Karol_szc ,
    I see that you are experiencing issues installing the printer on the Windows XP computer. I would like to help you out with this issue today.
    I have provided a document to check your system to make sure if does meet the system requirements.
    Windows XP: 'Your System Does Not Meet the Minimum System Requirements' Message Displays on the Comp...
    Check your version of .Netframeworks. How to Check Which Version of Microsoft .NET Framework is Installed in Windows?
    Run the Windows updates to get the most up to date one installed.
    What version of Internet Explorer are you using?
    IE is integrated into Windows and is part of the Windows updates.
    I suspect you need IE 7 at least. I believe this is because HP software piggy backs from Internet Explorer.
    If you need further assistance, just let me know.
    Happy New Years!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • HP Laserjet 2100M not printing with 10.6

    Hi,
    I've been trying to print a document all evening on my HP Laserjet 2100M with the HP 100 Mbps network module. I've tried it on both my iMac and my MBP, no help there. The printer program is saying that it is sending the job to the printer, but the light does not even blink on the printer.
    Any idea?

    Hi Andrew, I'm back home!
    First I did a Telnet to the printer address and confirmed it had the right settings. All looked perfect to me.
    ===JetDirect Telnet Configuration===
    Firmware Rev. : G.08.49
    MAC Address : 00:30:c1:0b:a5:b9
    Config By : DHCP
    IP Address : 192.168.1.10
    Subnet Mask : 255.255.255.0
    Default Gateway : 192.168.1.1
    Syslog Server : Not Specified
    Idle Timeout : 90 Seconds
    Set Cmnty Name : Not Specified
    Host Name : REPLICATOR
    Default Get Cmnty : Enabled
    DHCP Config : Enabled
    Passwd : Disabled
    IPX/SPX : Disabled
    DLC/LLC : Enabled
    Ethertalk : Enabled
    Banner page : Disabled
    OK, I reseted the printing system. Then I added my HP LaserJet using the HP Jetdirect - Socket mode (as I always did in preview OS X version). I put the IP address of the printer, let the Queue name empty, Named the printer and the Print Using auto selected correctly HP LaserJet 2100 series. Then I clicked Add. The print dialog tried to "Connect" to the printer for Installable Options. This was taking forever to finished. So I clicked on Configure... and selected the options I knew was there myself.
    I tried then printing from Stickies (something simple), it told me the printer was busy. I put it off, then on, and retried and it worked... Try a page from Pages too, working...
    Maybe reseting the print system helped, because last week I also put the printer off then on, and the problem stayed there. Tried the same on my MBP, and it worked too! Cannot figure out what I did wrong the first time. Maybe I really needed to print something, and Murphy's Law came in!

  • Can not print with HP LaserJet 6L since the upgrade to Mavericks.

    Can not print with HP LaserJet 6L since the upgrade to Mavericks. Any alternative driver for this printer?

    I have an HP LaserJet 5P and had the same problem. My LaserJet is connected to a D-Link ethernet print server, then to an Airport Express to support wireless printing.
    As recommended in earlier posts, I first downloaded the Gutenprint HP drivers at Sourceforge, version 5.2.9 That did not work. Then found the reference to the Apple kb here: http://support.apple.com/kb/dl907
    Downloaded these drivers. When setting up the printer, I got the autoselect option for Generic Postscript Printer and used that. Printer worked, but printed out garbage. I then deleted the printer, and this time selected the HP LaserJet 5P CUPS + Gutenprint v.5.2.9 THAT WORKED! I don't know if was the combination of downloading the drivers from Sourceforge and the Apple kb, or just the Apple kb that solved the problem, but I'm glad this is now sorted.
    I was a bit surprised when I hit this snag to begin with because the last upgrade I did from Lion to Mountain Lion, I did not have this issue. It was seamless.

  • Can not Print with HP LaserJet 5000 and Epson AcuLaser C9100

    I am using MacBook Pro 2.3 GHz Intel Core i7 with Mac OS X (10.6.6)
    I already install the latest print driver from the Apple Software Update website.
    The driver for HP is Ver. 17.5 & for Epson is Ver. 5.2
    I connect two of the printer to my Belkin Surf N300 wireless N Router with ethernet cable.
    The error when print to HP LaserJet 5000 is as follow:-
    Unable to get printer status (Not Implemented)!
    Network host 'x.x.x.x' is busy; will retry in 30 seconds...
    This error can stay forever if I do not delete the print job
    The error when print to Epson AcuLaser C9100 is as follow:-
    Printer not responding
    This error can stay forever if I do not delete the print job
    Previously I can print with my emac with OS X 10.4.10, but now I can not print with 2 of my printer.
    My 2 printer are in good condition, so this is not the printer problem.
    Please, do anyone know how to fix this problem fast, because I need to use this two printer for my business.
    Thanks in advance.

    That is not what Greg needs to know. That is just the way that the IP addresses are assigned to the printers.
    Your problem is probably that the printers were probably originally found by AppleTalk. AppleTalk is not included in Snow Leopard. If the printers support Bonjour, they should be found that way. Otherwise, you have to use other methods.
    How did you add your printers on the new computer? If you delete them from Print & Fax, how would you add them again?

  • Elements 11 will not print with Epson R2000?

    Cannot make Elements 11 work with new Epson r2000 printer.  Prompt on screen states it is not compatible or settings are not correct.  Epson tech support worked on it, said to contact without success, said to contact Adobe.  Printer works fine on all other applications.  Help please.

    Thanks again.
    Richard
    Date: Thu, 12 Sep 2013 08:49:39 -0700
    From: [email protected]
    To: [email protected]
    Subject: Elements 11 will not print with Epson R2000?
        Re: Elements 11 will not print with Epson R2000?
        created by A.T. Romano in Premiere Elements - View the full discussion
    Ollie37
    Thanks for the follow up.
    Barbara Brundage in the Photoshop Elements Forum will probably have the answer to your Photoshop Elements Epson scanner issue. Look into that Twain driver. She will give you good input on all this.
    Also, see your other thread about Adobe telephone contact information. I have posted in that other thread also.
    ATR
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5676121#5676121
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5676121#5676121
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5676121#5676121. In the Actions box on the right, click the Stop Email Notifications link.
         Start a new discussion in Premiere Elements by email or at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • Laserjet 2600n not printing black on one side of page. already cleaned the laser/scanner assembly.

    laserjet 2600n not printing black on one side of page. already cleaned the laser/scanner assembly. i've cleaned the assembly a few times beofre to restor the colors as the printer is in a semi-dusti environment.  after cleaning the printer was fine, then about a week later, the black - and only the black - stopped printing on the right side of the page.  the text is straight across left to right then starts to waver and then then stops altogether.  i tried a different black toner cartidge and the problem remains.

    > so this is strictly a hardware issue as no drivers are involved. Yup. > Still prints all black.   Ok its not the controller. > Still prints all black.   Ok its not the fuser. >  its still prints all black. OK its not the laser itself > it still prints all black. Not that part either. > What else left is there?  Formatter board hasnt been mentioned.  Something is sending a command to the printer that is telling it to open up the doors and charge the entire page.  Normally the laser is responsible for charging the media.  As the media passes over the toner doors it atracts toner particles.  Then as the paper continues it rolls past the fuser where heat melts the particles into permanent place. > The power supply board maybe?   Perhaps but not likely.  If you have a spare you could try it but power supply problems usually result with the machine unable to boot or print correctly, not printing too much as you have described here. > Is there another part you would reccomend I look at?
    You could try the old Halfway test just to verify that the problem is coming from teh laser/toner part of the printer.  http://www.printertechs.com/printer-troubleshooting/halfway-test Your paper may have somehow gotten a staic charge that opposes the charge of the toner, thus auto attracting all particles in range as it passes over the toner doors.  Might want to grab a fresh ream of paper to test and rule somethign crazy like that out. Not very many options left after that.     

  • Just bought a new Airport Extreme BS. After setup my iphone4 won't find the network (not even with manual entries), but my iMac (2009) does. What is wrong?

    Just bought a new Airport Extreme BS. After setup my iphone4 won't find the network (not even with manual entries), but my iMac (2009) does. What is wrong?

    Well, after another call with Apple support and the engineers, no success.  After spending over 20 hours trying to debug this, I give up.  Apple was basically fishing for a solution with trial-and-error settings on the iphone.  Then they wanted me to plug in software to log my iphone connections to the router, etc, etc., etc., at which point I decided I no longer wanted to participate in their testing process and will simply return the router.
    25 hours of my life I'll never get back.
    Big bummer, and frustrating for all the obvious reasons.

  • Lightroom 2.5 not printing with main account user but prints with a new use

    I have been troubleshooting all day. My new epson r280 is not printing with LR2.5 though it prints in other applications fine. Called epson and we are sure that I have the latest drivers, etc. Called Adobe and they had me create a new user in accounts in system preferences-accounts. When I tried printing from the "test user" LR printed with my epson printer. Adobe said the problem was with my system permissions and I had to reset my system permissions. This doesn't sound right to me. I ran disk utility and repaired my permissions but LR still doesn't print using my original user. Genius Book suggests going to Library-Preferences and to delete the plist. Does this sound right? And do I delete the p-list for LR or for the epson printer? What happens when you delete a p-list? Will I lose my catalog in LR? I would appreciate any help on this problem.

    Just trying again to see if anyone has any solutions for this question. Thanks

  • Why will my epson artisan 810 will not print with ipad?

    Why will my epson artisan 810 not print with iPad?

    Because it is not a Airprint enabled printer.
    http://support.apple.com/kb/ht4356

  • Officejet Pro 8500A is not printing with Yellow cartridge. Full cartridge and good health ...

    I have an OfficeJet Pro 8500 which is not printing with the Yellow cartridge.  Printing with the Cyan, Magenta, and Black cartridges is fine.  Diagnostics show all cartridges properly installed and having adequate ink supplies.I replaced the Yellow cartridge with a brand new XL cart, but to no avail.  I cleaned the orifice with Isopropyl alcohol and a cotton swab, thinking perhaps there was some dried ink or an impurity there.  The problem still exists.There are no error messages, either via software or at the printer itself.  The printer is out of warranty (imagine that!).I have used HP products for well over 15 years, partly because HP support has been historically excellent.  After reading some of the posts on these forums, it seems that HP has allowed their support quality to diminish - significantly.  I hope that is not the case in real life.Any ideas out there?

    I am having same problem. OfficeJet Pro 8500A Premium.  Not printing with Yellow. First replaced Yellow cartridge with new, then spoke with HP Support yesterday and was told that the Black and Yellow Printhead must need to be replaced, at a cost of $49.  New Printhead arrived today, inserted and still having same issue with YELLOW! So, for the cost of a new Multi-Pack of print cartridges (which had the Yellow I used to replace the low ink), and the new Printhead, I could have purchased a NEW CANNON PRINTER.  I have used HP Products for over 20 years - both professionally (HP Plotters) and at home (always HP Printers, Scanners, Multi-devices, etc.  I am VERY frustrated!

  • Can only print with manual feed and NOT from the paper tray from websites

    When I try to print something from a website, I must manually feed the paper in the manual feed slot. It will not print from the tray. This problem does not happen when I print something from an email with no downloads or something from MSword or Excel. So, it's most likely a browser printer setting issue. Any ideas?
    Thanks

    Probably related to printer preferences and how they relate to Firefox. If you did the complete reset all the printer setting that Firefox would saved would have been cleared and gone back to the default settings. Without familiarity with that specific printer ''(or even knowing which printer you are using)'' the best advice I can offer is to seek help from a support forum for that brand printer, or for you to reinstall the printer software to get back to the defaults.

  • H-P Laserjet 4L printer will not print with Windows 7 operating system. Need help

    I have an H-P Laserjet 4L printer that worked fine with a Dell PC and Windows XP. But, it no longer worked when the PC was updated to Windows7. I was advised to buy an adapter that would accept the H-P plug and connect to the PC by means of a  USB port. I did that, but the H-P still will not print. Anyone know what to do about this problem?
    EugeneZ

    Hello EugeneZ,
    Welcome to the HP Support Forums!
    To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial LaserJet Forums.
    The support page for your product may be helpful in the meantime: HP LaserJet 4L/mL Printer series
    I hope this helps!
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • HP Color LaserJet 3600(not 3600n) with Fast Ethernet port - can I use it?

    Hello! There is a HP Color LaserJet 3600 in our company connected via USB with XP-based PC. Recently I decided that we need this printer be shared directly trough our ethernet network, so I started to learn manuals - its own manual, Jet Direct, and all that stuff. The printer's manual says that HP Color Laserjet 3600 does not have neither its own ethernet port, nor support for embedded print-server like JetDirect 620n.
    But! 
    Visual check  shows that this HP 3600 DOES have its own ethernet port and if I connect it to network or at least to a notebook - it blinks like any other ethernet port with "lights" should do. 
    However.
    Neither front panel, nor back panel says anything about network support(like letter "n" in model name).
    Configuration page print also does not know about that mysterious port.
    So my questions are:
    1. What is this port actually?
    2. Can I use it to share printer over network? Maybe, there is a way to upload 3600n's firmware somehow? 

    The product you have seems to be a commercial printer. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You may find the Commercial Laserjet board here.
    http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
    You can also find the article pertaining to this product here:
    http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesI...
    (contains basic troubleshooting info, manuals, drivers, etc)
    Hope this helps!
    Help the community by marking this post as a solution if it solved your issue!.
    If my post helped you in any way, please click the blue KUDOS star under my name! It would mean a great deal.

Maybe you are looking for