HP mini 110-1116NR laptop fatal error code CNU939DV7 askin for password

Upon startup it asks for current password. When you enter it 3 times wrong it says fatal error code CNU939DV7. Ive tried every password on the help site but none were for the same fatal error code. Please Help!
This question was solved.
View Solution.

Hi,
           Try the below code
e9lofo1t6x         (3rd letter is L)
"I work for HP."
Please click the "White Kudos" star to say thanks for helping.
Please mark "Accept As Solution" if my help has solved your problem.

Similar Messages

  • HP mini 110-1116NR laptop fatal error code CNU9390DV7 askin for password

    Asks for password upon startup and 3 wrong entries says fatal error CNU9390DV7
    This question was solved.
    View Solution.

    Hi,
              Try the code
    e9lofo1t6x
    "I work for HP."
    Please click the "White Kudos" star to say thanks for helping.
    Please mark "Accept As Solution" if my help has solved your problem.

  • Hp mini laptop fatal error code

    I keep getting fatal error code CNU9277JZ I don't know the password and can't get in it and my mother doesn't remember it.

    Hi,
    Please try (all lower cases):
        e9lo7xxw07 (the 3rd char is lower case of L and 9th char is a zero).
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • HP Mini 110-1051TU Laptop Bios Password Reset

    Dear Sir
    I have a HP Mini 110 Notebook, but I can't changed my BIOS Password. After using ESC Key three times on Enter CURRENT Password, one error  shown on the post screen.
    Password check failed
    Fatal Error...System Halted.
    CNU938BVPN
    Please Help....
    This question was solved.
    View Solution.

    Hi:
    Try this unlock code:
    e9lofup629
    The third character in is a lower case L

  • HP mini 110-1116NR BIOS password

     when I start my net book (HP mini 110-1116NR) its asking me for password  and then Error-CNU94198NX
    Please someonetell me whats happening

    Hi,
    It looks like your machine has generated a halt code which happens after entering an incorrect Bios Password 3 times, so try the following.
    Please be aware that this is not supported by HP and you try it at your own risk.
    Try entering     e9lov3ou94               ( Note: the 3rd character is a lower case L )
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • HP mini 110- 3500 laptop fails to boot after SSD upgrade

    Hello,
    I recently bought a "crucial 250gb 2.5 " SSD and 2gb RAM (also by crucial), to upgrade my HP mini 110-3500 laptop, which was exceedingly slow. But unfortunately, the laptop has refused to boot when powered on. What can I do? I am very worried.
    Enkay1

    You answered. That is what I thought. You have DDR3L-1600 low voltage 1.35 volts. Low voltage will run at the higher voltage (1.5 volts) but it is just not the ideal memory for the older hardware. You need DDR3-1333 memory as HP specified for the laptop. You can confirm or refute my diagnosis by putting in the old memory and see if she boots.  This is the part mumber you need: 621567-001 http://www.ebay.com/itm/2GB-COMPAT-TO-621567-001-A3803335-A4100445-A4427375-/230655741975?pt=LH_DefaultDomain_0&hash=item35b4275017  Does your memory have 8 black blocks on the side or just 4? You want 8. Also if you have Windows 7 Starter you cannot use 2 gigs of RAM. If this is "the Answer" please click "Accept as Solution" to help others find it. 

  • My hp mini 110-3700 laptop say battery not present

    My hp mini 110-3700 laptop say battery not present, but i can see the battery s/n under the system info

    Please how can i fix this? I need your help please

  • Blu-ray Error: fatal error, code 6, audio buffer underflows...

    Ughh.... So its been a few months since I stopped using CS6 Encore because it loves to crash for all kinds of bad reasons. Today I needed to do a new project, and used a simple 1920x1080p MP4 file created by Adobe Media Encoder, and used a basic menu template in Encore. Also added a slideshow timeline with one Mp3 audio set to loop. During the building image part of the build process, I get the fatal error code 6, audio buffer underflows. Total bitrate too high neat time = 0.00000 seconds -
    First off, I set the BR transcode setting to auto and it spends  pleanty of time transcoding the file to a 15mbps bitrate, so why is Encore not first taking care of all the source files correctly in transcoding...?

    Ok.... 100% the fault of the software. I am an SE, and build systems all the time for my business, so if I knew of these simple problems, Id go into the code and devise a solution...please Adobe, fix Encore.
    Here are my simple finding from solving this problem (first post):
    - Of the 2 simple Mp4 files produced by Media Encoder, one, which runs only 2 minutes, had a peak of a little over 10mbps. I dropped the file back into Encoder and set the same mp4 profile to max of 6mbps and then replaced the file in the encore project, ran build and it worked fine.
    SO.... If I can use a simple free bit of software to look at the bitrate of a file (google Bitrate Viewer) and determine that the peak was possibly too high, why oh why cant adobe write a better transoding logic algorythm to decide if a video in a timeline needs to be reprocessed at a slightly lower bitrate before just attempting a build and then throwing an error. For the love of all that is holy, please tweek your transcoding decision process to prevent these simple errors.

  • Please Help Me!  Encore giving error message on Build:  "fatal error", Code: "6", note: "video buffe

    Hello,
    I have been trying to build a project (a 50gb Blu Ray disc) for the last couple of days and I keep getting an error message I have never gotten before.  The error says: "fatal error", Code: "6", note: "vide buffer underflows  Total bitrate is too high near..."
    I don't know why this is happening.  I build this entire project from the ground up once before using the exact same assets but I accidently deleted that project file so I had to put it together again.  But it was practically identical.  And it would build the project just find.  I deleted the cache folder.  I deleted the main video timelines and recreated them.  I made sure the transcode settings for bitrate were not too high.  I did everything I can think of.
    Can someone please help me?  I have no idea what to do now.  The frustrating thing is that the error message doesn't tell me what asset the problem is with or anything.  This is a rather complicated project.  I have two full length movie files (about 90 minutes each) and seven video special features.  I have five audio tracks and a couple of subtitle tracks.  I don't have any idea what asset is causing the problem!
    But I used all these same assets before and I built the project perfectly.  And it is not the subtitles because I deleted the subtitle tracks and I still got the error message.
    Is there any way of knowing what assets are causing the problem?  How can I fix this?
    I have a number of people who are waiting for the completion of this disc so I need to get this resolved pretty soon.
    Thanks.

    The error says: "fatal error", Code: "6", note: "vide buffer underflows  Total bitrate is too high near..."
    What is the rest of the error message?
    What version of Encore and what operating system?
    using the exact same assets
    What format? Already transcoded m4v/a3c 5.1 or what? Does Encore show them for Bluray as "Do Not Transcode"?
    What were the export settings, particularly bitrate?
    Is there any way of knowing what assets are causing the problem?
    Not through the error message.
    Rather than deleting elements to see what causes it, I would add elements (e.g. you got the error, deleted the subtitle tracks, and still had the error, leaving the possibilit that a cache or similar is contining the problem even if the subtitles caused it).
    So add just the menus and timelines, no extra audio, no subtitles,
    When starting a new project, make sure you are using a new name for the project.

  • Blu-ray: "fatal error", Code: "6"; "Note:"

    Blu-ray: "fatal error", Code: "6"; "Note:"
    That's the error I got when Encore CS3 started to actually write to the bluray burner.
    It's worked many other times but this time it did everything except the burn.
    If I reboot or change blanks it doesn't seem to matter. When it gets to the stage of starting to write to the disc, I get the message above.
    Real helpful, right?
    Hope there some "real" help here.
    Thanks,
    Steve Garman
    HP XW8200 3.4 gig Xeon Dual and 4 gigs ram. XP Pro with SP2.

    I can't seem to get any response here so I'm wondering if there is any list of Encore errors on the Adobe site? Errors like this are pretty meaningless unless you have a list of explanations. Any cluses who might have one?
    Thanks,
    [email protected]

  • CS6 - Blu-ray Error: "Fatal Error", Code: "6"

    Greetings,
    I have gone through about 15 Blu Ray Disks in the past week, trying to burn one wedding project.
    When i burn to DVD - its fine... but when i choose Blu Ray, it gets about 1 hour in and then comes up with 'Blu-ray Error: "Fatal Error", Code: "6".
    I have tried to re-export all files for burning, in two different blu ray formats - but it continues to come up with the same.
    I have used Encore for years but have just upgraded to CS6 and im getting these errors. 
    What am i doing to cause this?
    Thx,
    James

    Try this first:
    Strange Errors in En? Project Changes Not Showing Up? Try This!
    Then type "fatal error code 6" into the "Ask A Question" box at the top of the main Encore Forums page, or the top of the Discussions page.
    You'll get 5 very relevant topics right away.
    Jeff

  • Blu-ray Error:'fatal error", Code:"6", Note: "Empty palette in IG composition.

    If i try to burn or create an ISO I get this error.
    Blu-ray Error:'fatal error", Code:"6", Note: "Empty palette in IG composition.
    Any one have an idea what this means?
    Maik

    Fixed!
    I had a broken /incomplete button in a menu. After replacing it with a new button everything worked.
    Maik

  • Encore CS4 Blu-ray Error: "Fatal Error", Code: "0", Note:''

    Has anyone encountered this: Encore CS4 Blu-ray Error: "Fatal Error", Code: "0", Note:''
    Any ideas on what it means or how to fix it?
    Burning to a BD-R.  Tried two different Blu-ray burners.  Created a Blu-ray Image first.

    For CS4 you must update the Roxio component http://forums.adobe.com/thread/400484?tstart=0
    More on Encore and Roxio http://forums.adobe.com/thread/528582?tstart=0 or direct to
    http://kb.roxio.com/search.aspx?URL=/content/kb/General%20Information/000070GN&PARAMS
    Also, Long File Names or odd characters Cause Crashing http://forums.adobe.com/thread/588273
    And #4 Here http://forums.adobe.com/thread/666558?tstart=0
    And This Message Thread http://forums.adobe.com/thread/665641?tstart=0

  • How OC4J handles fatal error codes

    1. Does OC4j cleans/closes all connections in the connection pool when OC4J detects fatal error codes? Does OC4J really work as per oracle documentation? Can I get an example showing how is it done?
    Oracle Documentation says:
    For each data source defined in data-sources.xml, you can define fatal error codes that indicate that the back-end database with which the data source communicates is no longer accessible. When OC4J detects one of these error codes (stated when a SQLException is thrown by the JDBC driver), OC4J will clean its connection pool. That is, it closes all connections in the connection pool. For Oracle, the predefined fatal error codes are: 3113, 3114, 1033, 1034, 1089, and 1090.
    2. When OC4J detects fatal error codes defined in an connection pool in data-sources.xml, how connections in the connection pool are handled by OC4J?
    3. When OC4J detects fatal error codes on one connection to Oracle database, then will OC4J restore / close the connection back to connection pool?
    4. Does OC4J really work on fatal error codes?
    Sample code of connection pool I used in data-sources.xml file where I defined fatal error codes:
    <connection-pool name="FSCMDS" inactivity-timeout="30" initial-limit="5" max-connections="5" validate-connection-statement="select * from dual">
    <connection-factory factory-class="oracle.jdbc.pool.OracleDataSource" user="" password="" url="" commit-record-table-name="">
    <proxy-interface sql-object="PreparedStatement" interface="oracle.jdbc.OraclePreparedStatement"/>
    <*fatal-error-codes*>
         <*error-code code="3113"*/>
    </*fatal-error-codes*>
    </connection-factory>
    </connection-pool>
    Please post answers on these questions...
    Thanks
    Venkat

    This forum is for general database questions, post your question here:
    OC4J
    Werner

  • EVENT 36888, Schannel A fatal alert was generated and sent to the remote endpoint. This may result in termination of the connection. The TLS protocol defined fatal error code is 43. The Windows SChannel error state is 252.

    I keep losing my network connection for a few seconds at a time.  Not  a big deal unless I just spent time filling in a form and have to redo it.
    Getting:
    A fatal alert was generated and sent to the remote endpoint. This may result in termination of the connection. The TLS protocol defined fatal error code is 43. The Windows SChannel error state is 252. Using windows 8.  I just installed the new ARRIS
    TG862 provided by Comcast. 
    Any Ideas?
    Also get the following errors in my events:
    The name "WORKGROUP      :1d" could not be registered on the interface with IP address 10.0.0.2. The computer with the IP address 10.0.0.3 did not allow the name to be claimed by this computer.
    Realtek PCIe GBE Family Controller is disconnected from network.
    Any help is appreciated

    Hi,
    Critical Kernel-power event ID 41 is used appear after PC restarts or randomly restarts with error
    BugcheckCode listed or a cold reboot. Do you get BSOD and some dump files?
     Default location is %SystemRoot%\Minidump. You can upload it to skydrive, then paste link here.
    How to use Skydrive
    http://www.wikihow.com/Use-SkyDrive
    Kernel-PnP event ID 219: A Plug and Play device driver on your system is failing to load due to a device driver or device malfunction, you can unplug any external devices (except mouse and keyboard, but please keep the latest drivers), and
    check device status in device manager, please also keep the all latest driver update of your PC.
    And for error 36888, I found a similar thread, please refer to this link
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/4c5430f5-43f6-41b4-97d3-03cfb3efa70b/schannel-error-event-id-36888-is-there-a-way-to-identify-what-causes-schannel-to-log-error?forum=winserverDS
    Regards
    Yolanda
    TechNet Community Support

Maybe you are looking for