Hp mini 110-4108tu upgradation

How To Upgrade the my hp mini 110-4108tu

Hi,
The following link shows its specs:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03194931
For cost/performance, upgrading the HDD to SSD otherwise buy a new machine.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

HP mini 110-4108TU network and bluetooth related queries

Hi, I cannot use the bluetooth in my Hp mini 110-4108TU, I tried to add device but couldn't connect my mobile via bluetooth as a result i cannot transfer files. Do I need to install driver for bluetooth, if yes then please help me about the driver. Also I would like to know how I should be able to use wi-fi and wlan, do drivers need to be installed also? Are the wi-fi and wlan inbuilt? In the device manager I see Atheros and Microsoft virtual wi-fi adapter present, what are these?
I have attached the image of the device manager pop-up box.

aratipatel wrote:
hp mini 110-4108tu blutooth driver
Hello aratipatel.
You will find your bluetooth's drivers in the "Network" section of this page.
Have a great day.
Please click the white star under my name to give me Kudos as a way to say "Thanks!"
Click the "Accept as Solution" button if I resolve your issue.

HP Mini 110 - 4108TU , Change display unit

Hi ,
In the screen resolution setting under display it shows Digital Flat Panel ( where as I am using my laptop screen itself ). Because of this my screen does not fit into the display of my laptop screen.
The resolution selected is 1024 x 768.
Please help me as to how do i change the display .
Regards.
Vasant

That is too bad about system restore not being enabled. I can understand that, considering how small the mini's hard disk is.
Follow the instructions on the follwing Microsoft web document
http://windows.microsoft.com/en-us/windows7/change-your-screen-resolution
if no joy, then reinstall the Intel video driver
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-108064-1&cc=us&dlc=en&lc=en...
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Hp mini 110-1100 ram

I was wondering if the ram can be expanded to 2 gigs

Hi,
Yes you can. Your machine has only one slot therefore you have to throw away the existing 1Gb piece and buy a new 2Gb piece of RAM. You can buy from the following link or use this info to buy elsewhere:
http://www.crucial.com/upgrade/HP+-+Compaq-memory/HP+Mini/HP+Mini+110-1100-upgrades.html
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Hp Mini 110 1013tu Keyboard is Not working after upgrade to win 7

Hello need help on weird happenings to my keyboard..
Before i upgrade the Operating System From Windows XP to Windows 7 the Hp Mini 110 is working fine..
All keys on keyboard is working and touchpad is also working.
But after upgrading to windows 7 some keys on keyboard are not working like z,x,c,v, left ctrl and other more keys..
what do you think is the problem??
Hardware Issue? or Driver Issue?
please help thank you..

Hello @MysticDragon ,
Welcome to the HP Forums!
I understand some of the keys on your keyboard are not working after installing Windows 7.
I do not see any drivers available for your notebook for Windows 7 on the HP website, so their might be some compatibility issues as it's going to rely on Windows update to find current drivers. This doesn't mean it will not work, but I cannot say for sure that it will.
Try this:
1. Click Start.
2. Click Control Panel.
3. Click Clock, Language, and Region.
4. Click Region and Language.
5. Click the Keyboards and Languages tab.
6. Click Change keyboards...
7. On the General tab, make sure English (United States) - US is selected in the Default input language field.
8. Click on any other keyboards in the Installed services list.
9. Click Remove.
10. Repeat for all other non-English (United States) keyboards.
You may also want to try rolling back to Windows XP and see if the issue persists. It is possible the issue is coincidental and not the direct result of the update to Windows 7.
Let me know if this works!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

HP mini 110- 3500 laptop fails to boot after SSD upgrade

Hello,
I recently bought a "crucial 250gb 2.5 " SSD and 2gb RAM (also by crucial), to upgrade my HP mini 110-3500 laptop, which was exceedingly slow. But unfortunately, the laptop has refused to boot when powered on. What can I do? I am very worried.
Enkay1

You answered. That is what I thought. You have DDR3L-1600 low voltage 1.35 volts. Low voltage will run at the higher voltage (1.5 volts) but it is just not the ideal memory for the older hardware. You need DDR3-1333 memory as HP specified for the laptop. You can confirm or refute my diagnosis by putting in the old memory and see if she boots. This is the part mumber you need: 621567-001 http://www.ebay.com/itm/2GB-COMPAT-TO-621567-001-A3803335-A4100445-A4427375-/230655741975?pt=LH_DefaultDomain_0&hash=item35b4275017 Does your memory have 8 black blocks on the side or just 4? You want 8. Also if you have Windows 7 Starter you cannot use 2 gigs of RAM. If this is "the Answer" please click "Accept as Solution" to help others find it.

HP Mini 110-3150CA - RAM Upgrade?

I just picked up a HP Mini 110-3150CA - I have 1gb Ram - But I would like to upgrade to 2GB ram -- can this be done? And what type of Ram do I buy?

Here is the Manual.
Manual
Instructions for upgrading memory are on page 51.
It uses DDR2 laptop memory 667 mhz which is commonly available even at a store like Best Buy. It only has one module so you have to replace the 1 gig module in it with a 2 gig module. You will be glad you did. It will run much better on 2 gigs.

HP Mini 110-3000 is anything upgradable ?

Hello HP experts, I need some help. Can I somehow upgrade my video card or RAM on my HP Mini 110-3000 ? Im looking forward to have a good gaming experience so that I dont have to buy any expensives laptop.

I'm not going to say that you can't upgrade your graphics card. but I would guess that if you had the tools and skill needed to sodder a new graphics chip into this system you wouldn't be here. so short answer for video upgrade, no. not going to happen on a notebook, let alone a mini.
but you can upgrade you RAM..
check this out for the dirty details
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00820047&tmp_task=useCategory&cc=us&dlc=en&jump...
you want to play games on this? are we talking minesweeper? maybe the HP image of the device doesn't do it justice but it looks tiny.. more like a netbook. these things just aren't made to crank out the big games.
This country, with its institutions, belongs to the people who inhabit it. Whenever they shall grow weary of the existing government, they can exercise their constitutional right of amending it, or exercise their revolutionary right to overthrow it.
Abraham Lincoln

How to upgrade RAM on the HP Mini 110-313?

It says the HP Mini 110's are user-upgradable RAM to 2gig.
How would I do this?

There should be a little door on the bottom of the machine where the memory chip is. Just order the memory and pop the old one out and put the new one in.
________________________________________________________________________________________________________ I Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly

2 GB Memory upgrade for HP Mini 110-3025tu

I recently bought this laptop HP MINI 110-3025tu
Specs
-atom n475
-1gb DDR2
My problem/our problem is this.
When i installed a new 2GB DDR RAM into MINI 110 and turn it on, it show black screen and no LED blink, just power button light on
then i remove the new RAM and install the original one into MINI 110 and turn it on again, it still got black screen
Please tell me if i can do something to fix this problem
Much thanks!
Joe

Yes, the issue is with Memory Controller on N455/N475 processor. It is having issue with working, with any and every DDR3 memory module...Here is on going thread, where couple of memory module are listed, that reportly is working...
http://h30434.www3.hp.com/t5/Hardware/HP-Mini-210-1102TU-Wont-Accept-2GB-ddr3-no-boot/m-p/317562#M32...
http://h30434.www3.hp.com/t5/Hardware/HP-Mini-210-1102TU-Wont-Accept-2GB-ddr3-no-boot/m-p/318498#M32...
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

HP Mini 110-3616 RAM Upgrade

My Father in law is looking to buy a HP Mini 110-3616, they come with 1GB RAM (and Windows 7 Starter), I haven't ssen one of these, is it easy to increase the RAM, will it make it a lot faster?
Thanks
Steve

Here is your spec. sheet again and it says that you are running a 32 bit OS, so the max that you are going to use is 2 to GB.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02780828&tmp_task=prodinfoCategory&lc=en&dlc=en...
A 4 gig stick will probably work in there, but the BIOS may not see it and as Paul suggested, try to get one from a friend to test it out.
As for the HP compatibility listing, I think it's wrong, HP has printed the wrong information before.
Run this scanner from Crucial and it will tell you how much memory for sure it will handle.
http://www.crucial.com/systemscanner/
Is that 71 £ for the 2 GB stick, if it is, that's an outrageous price. Shop around a little more, a 2 GB DDR3 stick at 1333 MHz is common as dirt and should be around 20 to 30 dollars US. I am sure you could find something on e-bay.co.uk that will work fine at a fraction of the cost.
Forget e-bay, just get it direct from Crucial.
http://www.crucial.com/uk/store/listparts.aspx?model=HP%20Mini%20110-3105sa&Cat=RAM
It's still expensive, but better then HP's price.

HP Mini 110-3520ca constantly restarts when trying to restore from usb flash drive

Hi,
I have a HP Mini 110-3520ca that I upgraded to Windows 8, but was having issues with freeze ups and shut downs so I decided to go back to Windows 7 Starter. When I tried to restore to factory default the files were corrupted and I couldn't restore from the recovery hard drive or my external back up files. I ordered the recovery USB flash drive from HP and tried to restore from it. It completes the Recovery Preparation and the Software Installation finishes, Windows starts to load, but Ithen it goes back to welcome to Recovery Manager. When I try to start Windows without the flash drive I get an error log that is below. Can someone tell me how to fix this or what needs to be done to get my Windows working again, any help would be greatly appreciated.
Carol.
Error Log:
Component: TDC Preinstall Diagnostic Tools for Windows 7 - TDC
Timing: Factory Update
This is not a Regional SKU
This is not an RCTO P2PP SKU
Error: Different LOC# detected:
Error: SKU number LOC# = 00
Error: REGSKU/OptionDashCode.ini value for ABC = 12
Error: SKU number incorrect for this LOC#=ABC.
Next Step: Please dash sku number with xxxxxx-12x
Next Step: Or use EEPROM and change LOC# in either SKU Number or CTO Localization Code
[17:16:38.37] ------------------------------------------------------------------------------------------
***CTO Error condition has been dtected in [Factory Update] phase !! ***
[17:16:38.38] Suggest to create PIN-log and send to TWN PDC NB-PreinPM for further analysis ...
[17:16:38.38] ------------------------------------------------------------------------------------------
[17:13:54.75] Start BBOffline.cmd...
UPDrv=[C:]
[17:13:54.77] Set UIA Error Code to 951
[17:13:55.39] WinPE is 32bit.
[17:13:55.39] Starts [FixUps].
[17:13:55.41] ---------------------------------------------------------------------
[17:13:55.41] FixUps.cmd...
[17:13:55.41] create overall progress info...
[17:14:15.89] FixUps.cmd completed...
[17:14:15.89] ---------------------------------------------------------------------
[17:14:15.91] Starts [Tweaks for SSRD].
[17:14:15.92] ---------------------------------------------------------------------
[17:14:15.92] SSRD Tweaks to change user default locale...
[17:14:15.92] Copy C:\System.sav\Util\TDC\MCPP\FBIRES\FBIUSRES.DLL.
[17:14:16.09] Run "Dism.exe /image:C:\ /Set-SKUIntlDefaults:en-US -image:C:".
[17:14:23.50] ---------------------------------------------------------------------
[17:14:23.50] Launch PININST.exe for Offline ...
[17:14:33.78] Starts [Sleep 10 sec].
[17:14:43.86] Starts [Create RStoneFUpdate.INI].
[17:15:20.91] Starts [create 1GB Pagefile for offline].
Volume in drive C has no label.
Volume Serial Number is 868D-C760
Directory of C:\system.sav\bbv
10/27/2014 05:15 PM 1,073,741,824 pagefile.sys
1 File(s) 1,073,741,824 bytes
0 Dir(s) 38,502,694,912 bytes free
[17:15:21.04] move boot.wim from FactoryUpdate to 2ndCap.
[17:15:21.10] Brand detection.
[17:15:21.80] ---------------------------------------------------------------------
[17:16:10.26] Start SysID Check...
[17:16:13.30] Start Option Code Checks...
SKU_DEF_COUNTRY=[39]
SKU_DEF_SYS_LOC=[fr-CA]
Reset country in administrator...
Reset country in Default user...
Reset System localed
Deployment Image Servicing and Management tool
Version: 6.1.7600.16385
Image Version: 6.1.7600.16385
Reporting offline international settings.
Default system UI language : en-US
System locale : fr-CA
Default time zone : Pacific Standard Time
User locale for default user : en-US
Location : Canada (GEOID = 39)
Active keyboard(s) : 0409:00000409
Keyboard layered driver : PC/AT Enhanced Keyboard (101/102-Key)
Installed language(s): en-US
Type : Fully localized language.
The operation completed successfully.
Updated System Locale info..
[17:16:27.37] Start PIN Tweaks...
[17:16:28.38] ---------------------------------------------------------------------
[17:16:28.40] PIN Tweaks to hide All for BurnBoot BBV and BBV2 on restored image...
[17:16:28.40] ----------------------------------------
[17:16:28.40] Tweaks for OOBE's Unattend.xml
[17:16:28.40] to pick up the proper file...
[17:16:28.41] ----------------------------------------
[17:16:28.41] rename unattend.org to unattend.or_
[17:16:28.44] ----------------------------------------
[17:16:28.44] without Light Sensor..
[17:16:28.48] ----------------------------------------
[17:16:28.49] This is Restored image by SSRD [SSRD.flg]...
[17:16:28.51] ---------------------------------------------------------------------
[17:16:29.40] Start MIR Tweaks...
[17:16:30.43] ---------------------------------------------------------------------
[17:16:30.43] [MIR Tweaks] ...
[17:16:30.43] ---------------------------------------------------------------------
[17:16:31.44] Start Factory Update(s)...
[17:16:33.45] Start QFE Offline installation...
[17:16:38.13] PININST_OFF: PASSED...
[17:16:38.21] Type C:\System.sav\Logs\BBFindEr.log...
[17:16:38.23] Type C:\System.sav\Logs\BBFindE0.log...
---------- C:\SYSTEM.SAV\LOGS\PININST_OFF.LOG
Result=PASSED
[17:16:38.24] There was no QFE installation...
[17:16:38.24] Check FUList.log if there is duplicate Desc...
Couldn't access C:\System.sav\logs\FUList.log...
[17:16:38.35] No Duplicated Desc is found... PASSED.
[17:16:38.37] There was no Factory Update...

Hi @Savvy58
I did some further looking into that Error Log you posted. Basically, it means that is looking for a certain location that doesn't seem to be there. This could be a problem with the USB Recovery drive that you have. I would recommend that you contact HP. You can reach HP Total Care at 1-800-474-6836 in North America or start here if you live outside of North America.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Netbook Mini 110-3830NR How do I create a restore image on a flash drive

I have a HP Mini 110-3830NR Netbook running Windows 7 Starter.
I want to create a restore image to original factory state.
The user manual recommends that I create a restore disk.
It further states that to create a restore image on a USB device, I need at least
a 16GB device.
Therefore I purchased a Hp v165 16GB flash drive that actually contains
14.8 GB of user space.
I could not find the correct info about creating the disk on the HP support
web site so I chatted with an HP Support technician. She eventually gave me
a link to a procedure that would create a restore disk for me.
Then she said I needed a 32gb flash drive !!
Is the user manual or the technician correct ??
Can I use the 16GB (14.8 actual), or must I buy a 32 GB flash drive ??
Thank You fljim

I would just try to create it, the recovery creator should tell you at some point if it is big enough or not, orignally 8gb was big enough for most W7 system's HP sold, but as time passed they had to upgrade the size recommendation to 32gb.
the 16gb should be large enough for your model.
This HP document says al least 8gb minimum, use 16gb for best results, very confusing, I agree
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01890478&lc=en&cc=us&dlc=en

Hp mini 110 RAM

im thinking of upgrading the ram on my hp mini 110-3601 sa but it got a choice of 2 the first one is : 2GB, 1600MHz, 240-pin, PC3-12800, shared DDR3 SDRAM Small Outline Dual In-Line Memory Module (SODIMM) andthe second one is: 2GB 1600Mhz PC3-12800 memory module (SHARED) i want toknow whats the diference between them and which one is better as im running w7 home premium can anyone help?
This question was solved.
View Solution.

Hi,
For RAM we need the machine is going to work, doesn't matter more expensive or faster. Please get the proper specs using the following scan:
http://www.crucial.com/systemscanner/
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Can I replace Processor on my hp mini 110-3012 tu ?

Can I replace Processor on my hp mini 110-3012 tu ? Replace Better Processor then intel atom

Atom processors are not readily available for sale like other CPUs. In many netbook systemboards the processor is soldered in instead of being socketed. For those reasons I will have to say it is both unlikely and not worth spending more that half the value of a netbook to upgrade it.
Forum member Huffer answered the same question about a mini 310 before. Read his response here.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Hp mini 110-4108tu upgradation

Similar Messages

Maybe you are looking for