Hp notebook crashes after upgrading to windows 10

After upgrade to windows 10, my notebook became blank.I had to switch off by hard reset on by power button. After sometime I started it took a long time about half an hour but windows 10 started. When I shut down, not book shuts down properly but power button reamins ON / lighted. Moreover sometimes windows starts normally... sometimes it remains blank after asking password. Pl. advise a solution...... Regards, Pawan

I'm having the same problems. I did update the driverrs for the HD Graphics and it now powers off when I shut it down. It still will not come out of sleep mode though and I can not disable the touchpad when using a mouse. Everything was running fine until it updated to Windows 10.

Similar Messages

  • Portege M700 crashes after upgrading to Windows 7 32bit

    Dear All,
    My portege M700 laptop has for the most part performed reliably.
    However, it used to be very sluggish resuming from sleep after a few wake-sleep iterations, taking >5min.
    I have now installed Windows 7 32-bit, which is working very well. There are no longer any problems with resuming from sleep. However, about 1-2 times per day now I get a message that Explorer has crashed and must restart. About once per week, the system locks up entirely with a windows blue screen (kernel fault). Most times, in the few seconds around the time the screen freezes, I hear the fan switch on at full speed (much faster than it ever normally runs) and the case becomes quite warm.
    I have installed the latest Windows 7 32-bit drivers from the Toshiba UK website.
    Can anyone help me diagnose the cause of these crashes?
    Many thanks,
    Chris.

    I changed the windows 7 power management settings for the fan to "keep coolest". In normal use, I can feel a slow slightly warm airflow. There's no fluff. All that looks fine.
    My suspicion is that something is making the kernel go into a loop (I suspect a driver fault) and that this makes the CPU get hot, and the fan kicks in as it should...
    Any other ideas for some specific diagnostic tests to try would be appreciated. The Toshiba "PC Diagnostics" tool passes everything except the network which reports as follows:
    [Diagnostic Results]
    NETWORK TEST (1) DONE PASS (Intel(R) 82566MM Gigabit Network Connection)
    NETWORK TEST (2) DONE PASS (Intel(R) Wireless WiFi Link 4965AGN)
    NETWORK TEST (3) DONE FAIL (Cisco AnyConnect VPN Virtual Miniport Adapter for Windows)
    NETWORK TEST (4) DONE PASS (VirtualBox Host-Only Ethernet Adapter)
    NETWORK TEST (5) DONE FAIL (Shrew Soft Virtual Adapter)
    C.

  • No sound after upgrading to Windows 8 HP G60-553NR Notebook

    I recently upgraded to Windows 8 from Windows 7 64-bit on my HP G60-553NR and went through 3 tiers of tech support with Windows because after upgrading to Windows 8 Pro.... I had no sound coming from my speakers from my notebook nor will sound play when headphones are plugged in. Windows Tech support said that there are no compatable sound drivers to download, which leaves me with no sound completely which is no bueno. So, is there a driver that I can download that will work on my notebook?! If not, how do I downgrade to Windows 7. I'm a DJ and I really need some sound like asap. Thanks in advance for your assistance. Thanks

    Do an HP system recovery to get back.
    If you have discs - put first in and boot.
    If not, you can go into settings from CHarms and advanced to select recover. Here's more: http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c03489643
    ... an HP employee expressing his own opinion.
    Please post rather than send me a Message. It's good for the community and I might not be able to get back quickly. - Thank you.

  • Am running Firefox 3.6.10. Am having problems with Firefox crashing after upgrading to Kaspersky Internet Security 2011. Anyone else having same problem. Oh, BTW am still using Windows XP operating system.

    Am running Firefox 3.6.10. Am having problems with Firefox crashing after upgrading to Kaspersky Internet Security 2011. Anyone else having same problem. Oh, BTW am still using Windows XP operating system.

    The latest flash player release is 11,0,1,152.
    Can you upgrade to this version and see whether the crash stil exists?
    Go to get.adobe.com/flashplayer to download and install flash player.
    In case you need direct link to installer/uninstaller, please go to http://forums.adobe.com/message/3952360#3952360 to find them.
    saranlee wrote:
    My computer crashes repeatedly and I get the message pages are not responding do you want to stop, and/or shockwave is not responding do you want to stop. I have Windows XP Service Pack 3, I am having the same issues whether I use Internet Explorer, Google Chrome, or Mozilla Firefox. My HP Pavilion Desktop has 504 MB of Ram and I am using high speed internet connection. Because it was crashing so much, I used the uninstall program for Flash player to uninstall Flash, I checked my registry and removed anything I saw that was Flash. I then uninstalled Google Chrome and Mozilla Firefox, then I reinstalled the most recent versions from their websites. I did the same for FlashPlayer and Shockwave Flash. I went to the Adobe website and had them check to see if it was working and it shows I have FlashPlayer 10.3.181.36. The page that shows  which version of flash player goes with Windows XP states that I should have 10.3.181.34 (This is what I thought I had before I updated, I was having the same problems). When I went into my computer to see what version I have, it shows 11.5.9.620 Activex and both Flash Player and Flash Player Object is listed as 10.3.181.34. My firewall for Windows is set to medium. I also am running Norton Internet Security. It takes anywhere from 3-6minutes for some of my games to load, and I have to refresh at least 3-4 times in order to play. When I do start to play it freezes frequently and I use escape to free it up. This has been going on for a month. I have no idea what to do. I am not very computer savy and I have been learning as I go.

  • Keyboard wireless key not working after upgrading to windows 8.1

    Hello,
    I am having hp pavilion dv6-6165tx notebook, where keyboard having a wireless button that turns ON and OFF all wireless devices, After upgrading to windows 8.1, HP Connection Manager is not getting installed, as well as Key is not working, key color turns red and white but no action is performed.
    Kindly suggest me some solution.
    Note: HP Doesn't provide drivers for windows 8/8.1 ONLY WINDOWS 7 for hp pavilion dv6-6165tx.
    Thanks.

    Hi @Jayesh_Bhadja ,
    Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion dv6-6165tx Notebook and the Wireless keyboard not working correctly. Here is a link to troubleshoot the keyboard.
    The HP Connection Manager is something that is for Windows 7 not Windows 8.1. I would uninstall this from your Notebook.  Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating. It has a troubleshooting tool in this.
    Make sure all your updates have been completed. I would try restarting my Notebook a few times.
    If that does not help I would uninstall the keyboard from the Device manager.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • Ethernet LAN not working after upgrading to windows 8.1

    After upgrading from Windows 8 to 8.1, my Ethernet LAN is no longer working. Wireless LAN connectivity is OK. I have run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I do not see a 8.1 driver listed for the Ethernet LAN.

    You're very welcome. See if the recovery manager still works so you can roll back to W8. Please read this guide for how to use it. http://support.hp.com/us-en/document/c03489643 If it doesn't then you will have to order a set of recovery disks from HP, or you can install this plain W8 OEM software this guy has posted on a link. Lots of folks have used it successfully, which is why I posted it. https://docs.google.com/file/d/0B0W9PBigPy94aVJWSndyTFNFMzg/edit?pli=1 Then use this tool to make the iso file bootable to a DVD or 4+ GB USB flash drive. http://www.microsoft.com/en-us/download/windows-usb-dvd-download-tool Yes, that really stinks why you and I could not upgrade without an issue. I disabled about 5 or 6 devices in the device manager and the code 12 would not go away. I have no clue why the PC works fine on W8 but not on W8.1. My notebook is a few years older than yours and it worked fine on W8.1 but not on W10. Go figure...

  • USB device keeps disconnecting/connecting after upgrading to Windows 8.1

    I have a device(Pedal for Sim Racing) connected via USB, everything is working fine in Windows 7 and 8 but after upgrading my machine to Windows 8.1 the device keeps disconnecting and connecting for like every 2 seconds. But after I open the Property Sheet
    in Game Controllers panel the disconnection issue was gone, if I reconnect the device the issue persist. Other people who have similar device also encounters the same issue after upgrading to windows 8.1. The issue persist with or without the device driver
    installed. 
    Any idea, what might cause this? 
    Best regards
    mark

    I'v got this exact same problem with my Win 7 desktop.  I've also got pedals and wheel but don't see it as different than all the other USB devices.  I'm using a bunch of USB, but no hubs, including 3 external storage hard drives. But the momentary
    disconnect appears in all devices as best as i can see..even my long time trouble free head phones..keyboard..and all.  Sometimes the sound goes away and if I unplug and replug them the sound comes back, and other times I have to exit and re enter the
    game. I also get video crashes ..maybe not related.IDK..and have to restart all, because I've got three black screens in Eyefinity. For years my system was trouble free and its just slowly started getting worse. I've thought it had to do with system "sleep"
    etc but long ago went to never sleep max performance etc..Makes no difference. Keep thinking its my hardware or my house wiring etc..But can't seem to solve it. I replaced my Mobo/chip/ram maybe 6 months ago and that appears to have not helped.  It seems
    to be getting worse. I hate to start replacing parts piece by piece..cost a lot of money and sometimes doesn't help.
    When I'm playing a game I can often hear "faint" sound of USB connect disconnect happening with regularity..that little bing/boink sound etc..So it must just be constantly happening...Seems weird. Didn't have anything like this happening years
    ago with pretty much the same hardware and same Win7 with the continuing updates etc.
    What can be causing this common problem?

  • Hi,catalyst control centre has stopped working after upgrading to windows 8 .

    Hi,
    i have a hp envy-6 notebook pc(Product number: B4P24PA#ACJ,Serial number:  [Personal Information Removed] , which comes with windows 7 home basic! after upgrading to Windows 8 Pro 64-bit operating system ,my catalyst control centre ,host application has stopped workiing .
    i have tried almost everything i could do but the problem still persists
    on every time restarting pc it displays the above error message.
    regards
    abhishek rao

    Hi,
    Have you checked in the Device Manager to see if all drivers are installed since upgrading? (look for yellow exclamation points)
    Uninstall the AMD driver and catalyst control center. Install the version  located in the download section of the web support portal for your sleekbook.It will install both driver (intel and AMD) and also switchable graphics capability if it previously existed.
    Best regards,
    erico
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • No audio device installed after upgrading to windows 7???

    after upgrading to windows 7 audio is not working error audio device not install driver error...

    Hi,
    You will need to identify your CPU and chipset. CPU-z is a free and safe utility that can do that for you.
      If your system has an Intel chipset with disccrete or onboard graphics or an NVIDIA chipset with onboard graphics, then the drivers are here at this Realtek download page.
    If your notebook is an AMD CPU and NVIDIA chipset, with a discrete graphics module installed, then the driver for your Conexant CX20549-12 will be here.
    Post you results here in your thread so others rsearching for the same information can benefit from it. 
    Best regards,
    erico
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Re: NB200-134 - FN key not working after upgrade to Windows 7 Ultimate

    My FN keys of NB200-134 is not working after upgrading from Windows 7 starter to Windows 7 ultimate. I tried installing every drivers found on Toshiba website for my lappy but still it does not work.
    Help please

    Hi asalamk,
    The FN keys are controlled by Value Added Package and Flash Cards Support Utility. I think you have forgotten to install these tools
    You should check the Toshiba page again and download both tools. Start with installation of Value Added Package then restart your notebook. After this install Flash Cards Support Utility. Once again restart and all FN keys should work properly now.

  • Plug and play speakers not working properly after upgrading to Windows 8.1

    After upgrading to Windows 8.1, my plug and play speakers do not work properly.  I have uninstalled and reinstalled them, and restarted.  When I try to play music, nothing comes out.  If I turn them off and back on, music will play for approximately 30 seconds, only from one speaker, then it turns off and fades to no sound.  They worked fine until I upgraded to Windows 8.1.  The manufacturer has not been able to successfully assist me.  Has anyone else reported a similar issue after upgrading OS software?  Any suggestions?  These are fairly new speakers, less than 2 years old, and not used very much.  I do have them installed via a K-V switch, and all other devices linked to the K-V switch are functioning properly (monitor and wireless keyboard).  Any suggestions would be greatly appreciated.

    @sisboldt ,
    Hello and thank you for posting on the HP support forums.
    So that I can better help you with your sound issue.  Please post back with your full model and product number.  Use this link to help you find the information.
    HP Notebook PCs - How Do I Find My Model Number or Product Number?
    Here is another link you may find useful.  Please give it a read before posting back with your system information.
    Advice for asking the "Very Best Question"
    Thank you again for posting and have a great day.
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    D5GR
    I work on behalf of HP

  • 2015 HP Envy 23 Ips monitor with Beats Audio is not working after upgrading to Windows 10

    Hi I have upgraded OS to Windows 10 recently. from then there is no sound from my monitor. FYI.. am ussing a Dell laptop to connect to the monitor witha HDMI cable. It was working fine before upgrade and suddenly it stoped working after the OS upgrade.

    Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how your notebook computer's monitor will not produce any sound after upgrading to Windows 10, and I would be happy to assist you in this matter! According to the available list of supported drivers for your monitor, there is currently no Windows 10 software published at the moment.  In the meantime, I recommend following the steps in this document on HP Products - Where do I find Windows 10 drivers and software for my model? I also suggest connecting the monitor on a different computer to test the hardware functionality of the speakers. I hope this helps! Best Regards

  • Various programs crash after upgrade to 10.6.4

    Various programs crash after upgrade to 10.6.4 but only late in the day / evening. There seem to be no crashes early in the day.
    After a reboot the problem is fixed and things seem to work OK.
    Might this be some kind of memory-related issues?? Programs not releasing memory until eventually there's nothing left?
    I'm a Windows guy until recently so am not up to speed with Mac software / hardware yet.
    Any suggestions?
    Thanks.

    Hi, I am facing major instability in MS Office for Mac 2008 after the 10.6.4 upgrade. Programs (Word, Excel, PowerPoint), just crash randomly. Mostly when opening existing Office documents but there is no fixed pattern.
    Tried Office auto update but no joy.
    Any suggestions
    Here is the MS Error log
    Microsoft Error Reporting log version: 2.0
    Error Signature:
    Exception: EXCBADACCESS
    Date/Time: 2010-07-23 20:37:36 +0530
    Application Name: Microsoft Word
    Application Bundle ID: com.microsoft.Word
    Application Signature: MSWD
    Application Version: 12.2.5.100505
    Crashed Module Name: libTrueTypeScaler.dylib
    Crashed Module Version: unknown
    Crashed Module Offset: 0x00009bd5
    Blame Module Name: libTrueTypeScaler.dylib
    Blame Module Version: unknown
    Blame Module Offset: 0x00009bd5
    Application LCID: 1033
    Extra app info: Reg=en Loc=0x0409
    Operating System Information
    Operating System: Mac OS X 10.6.4 (Build 10F569)
    CPU: Intel Core Duo, Number: 2, Speed: 2147 MHz
    gestaltPhysicalRAMSize err = 0, result = 2047 MB
    gestaltSystemVersion err = 0, result = 0x1064
    Screen: 1440 x 900, depth = 32, ltbr = 0, 0, 900, 1440
    Microsoft Application Information:
    Error Reporting UUID: 0B338D65-7DAA-4B4A-B8B1-0C17F587C24A
    Time from launch: 0 hours, 14 minutes, 46 seconds
    Total errors on this client: 40
    Does this help at all ?

  • Many of my Apps are now crashing after upgrading my iPad 1 to OS 5. What's up?

    Many of my Apps are now crashing after upgrading my iPad 1 to OS 5. What's up?

    Free memory.     You are probably getting crashes becasue you have too much stuff floating sround in memory.  Double tap the home button to see the task bar.   Touch and hold any of those icons until they jiggle, then delete them all by touching the minus sign.
    Do this every day, or more oftern if needed to keep the system freed up.   If you are using safari a lot, make sure to fully close some of the windows by touch the x on the tabs.  Each window uses some active memory.
    From time to time, do a full reboot by holding the sleep and home button until the apple logo appears.  Ignore the red slider.  This also frees up some system resources.
    The iOS system is supposed to do this for you, but since the intro of ios 5 there are a fair number of folks crashing.

  • ICloud Group contacts disappeared after upgraded to Windows 8.1.

    After upgrading to Windows 8.1 received message "The set of folders cannot be opened.  The information store could not be opened."  When opening the iCloud contacts in Outlook 2010.  I performed the fix of signing out of the iCloud control panel and back in to resolve the above error message and was able to access my addresses.  However, all of the iCloud Group contacts disappeared from Outlook and from iCloud.  Is there any way to restore the iCloud contacts back to a point when the Group contacts still existed.

     Hi @Tomhum2010 ,
    Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP ENVY 14t-1200 CTO Beats Edition Notebook PC and issues after an Windows 8.1 update. I recommend to restore the BIOS defaults.You could restore the BIOS with this document selecting the reloading the BIOS default settings which should resolve the fan issue.
    Here is a link to the HP Support Assistant. Just download and run the application and it will help with the software and drivers on your system. If the drivers are not updated this could cause this same issue.
    If that does not help at the end of the document it shows you to do a hardware test.
    Please note remove any and all USB devices before troubleshooting. Disconnect all non-essential devices
    Hope this helps you out.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Maybe you are looking for