HP Officejet Pro 8600 fax confirmation time and date fields has all zeros

My fax confirmation sheet for the time and date of my HP Officejet Pro 8600 prints all zeros. How do I reset the time and date for this function?

Hello rschne,
Welcome to the HP Forums.
I see that you are having an issue with the date and time being all zeros on the fax confirmation.
Is the time and date set on the front display of the printer?
Please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
Write me back when you have time and I will be happy to assist further.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Similar Messages

HP Officejet Pro 8600 fax from computer will not fax more than one page without canceling job

HP Officejet Pro 8600 MFP running on Windows 7 64 bit. I purchased this printer almost a month ago. The install was simple and straight forward with no apparent problems but when trying to fax from computer the program seems to be only able to fax one page faxes. Any multiple page faxes will show a message "spooling" for 10 to 15 seconds then it will cancel the entire fax. I have tried this in both wired and wireless modes with the same results. I have sent 30 page plus faxes from the printer without any problems, it is only the fax from computer that seems to have memory issues. Any solutions out there?

Have you tried updating the firmware on the printer?
If not, here is a link to the most recent firmware:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=bi-101905-4&cc=us&dlc=en&lc=en...
Try that and let me know if it helps to resolve your issue.
Best of luck,
Kyle
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

HP Officejet Pro 8600 Plus N911g Devices and Printers Page Is Slow to Open

Hello, I have HP Officejet Pro 8600 Plus, model N911g, installed as a wireless printer. I have Windows 7 64-bit. My Devices and Printers page takes over two minutes to open. While I am waiting, if I go to Print Spooler Services and click Restart, the page opens right away. Once the page is open, in the HP Officejet Pro 8600 Plus device, I ran Troubleshooter and it took about 1/2 hour to finish, and it reported and supposedly fixed a problem in the Print Spooler service. The assigned Port looks like a recovered port. However, if I restart the PC and try to open Devices and Printers again, the delay is still present. I had trouble installing the HP program including the Scan to PC functionality, because response time was so slow. Now it's installed and working, but the HP program is quite slow to open. The spinning circle spins and then stops, almost like it has given up opening the program. Then several minutes later the program opens or the requested action begins.

Check the document I linked below. Step 6 might be the solution you are looking for but it will not hurt to start from the top.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02817031
Binary_Zen (worked at HP )
Click the white Kudos star to say thanks
Please mark Accept As Solution if it solves your problem

HP OFFICEJET PRO 8600 FAX phone cord

I am trying to setup the fax capability on my HP Officejet Pro 8600 all in one printer.
I have digital phone service and my phone cord runs from my internet modem.
I did the setup and the test failed due to 'Phone Cord COnnected to Correct Port on Fax: FAIL'
Test Report advises to put active phone cord in in the '1-line' port and then run the printer supplied cord in the other port ('2-ext') and connect that to the phone base. When I do this I do not get a dial tone.
If I switch the cords (put the active phone cord in '2-ext' port and HP cord in '1-line' port and to the phone base) I get a dial tone but the printer fails my fax setup test saying 'port not connect to correct port'
HELP ?

If you just need fax once in a while, and you already have a scanner to scan any document into digital form. You might want try a *free* internet fax service, like fax.com, they send your document to a fax machine, and even receiving faxes goes to your email.

Officejet Pro 8600. faxes being sent or received are being cut off.

I have a OfficeJet Pro 8600. Most (8 out of 10) faxes being sent or received are being cut off. I or they only receive half the sheet. HELP!!!

Hello bonnie753, and welcome to the HP Forums, I hope you enjoy your experience!
I see you are having fax issues. I would like to assist. Are you using the fax line that come with the printer? Are you plugged direct into a telephone wall jack or are you running into a modem? Do you have anything between the printer and the wall jack on the fax line?
I would suggest performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would also suggest changing a few settings under your fax menu on the front panel of the printer:
-Go to your setup menu
-Select Fax settings
-Set fax speed to slow
-Turn off Error Correction Mode
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Officejet Pro 8600 Plus ...paper TRAY wont close all the way?

My Officejet Pro 8600 Plus paper tray will not return to the proper position. This has happened TWICE now, and always about 3 weeks into using it...
I returned the first printer and replaced it with the same because we love the features and ease of use. But now, AGAIN??
I tried printing with it hanging out this time..it will print, but ....COME ON! It makes it real hard to pull out the tray that my paper lays on after printing!
I called HP support the first time, he couldnt help me. Just said replace it. There has to be something I can do a button or something? I cant see it..does anyone else know?

Zadora wrote:
Unofrtunately useless information. By trial and error I have found the only way to replace the tray is to lift the entire printer from the front at about a 20 degree angle and then the tray slides in. Very defective design. Never buy another HP.
It is possible you have a defective unit, I would suggest you Contact HP for service.
It may not be any consolation for you, but the tray works fine on my Officejet 8600 Pro Plus.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP Officejet Pro 8600 - Faxes from Win 7 computer are cancelled

When attempting to fax from the computer (i.e. word doc) the fax is cancelled.
I have a wireless network, but the computer I am faxing from and the HP 8600 are connected to the router via RJ45 connections.
I can fax OK from the HP8600 control panel, and all other printing functions work OK from this computer and other wireless connected PC's.
I am running Windows 7 Home Premium SP1 on the computer I am trying to fax from.
I have read other forum entries that seem to indicate that only a USB connection allows faxing from the computer. Is this correct, or am I missing a driver for ethernet connected devices? Thank you.

Hey there @rich126 ,
I have been researching the issue you're having with your faxes from Microsoft Word being cancelled, when attempting to send a fax from your PC. I haven't found any concrete information stating that faxes will not work if an ethernet connection is being used, nor have I found any stating that it should work.
Could you try connecting a USB and then try faxing from your PC again and let me know what happens?
If you notice any other errors or messages please include them too and I will continue to look into this for you.
Uninstalling and reinstalling the printer may help, if you wish to give that a shot.
Enjoy the rest of your day
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Officejet Pro 8600 fax problem

I need to connect my fax to our office phone service. I must dial "9" first to get an outgoing line. How can I program the fax to do this?
Thankls.

Hello halrms,
I see you are trying to fax with a phone line that a "9" needs to be dialed to gain access to an out bound line. You should be able to find the answer to this here: Faxing with Long-Distance Access Codes, Calling Cards, or Internationally.
I didnt not have a chance to try this, but see no reason as to why it will not work.
Screen shot taken from above link.
Let me know if this worked.
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Officejet Pro 8600 Plus will not print but is connected and says that the print job is 100% Complete

Hi All,
I'm printing from a MacBook Pro using OSX Lion. It says that Officejet Pro 8600 Plus is connected and that the print jop is
100% complete except that nothing comes out of the printer. I've done all of the test prints and they've printed just fine.
I tired all of the troubleshooting steps listed on the support guide and still nothing. HELP!

Not a reply but another plea for help.
There seem to be so many people with wireless problems that a) it seems silly to start a new thread and b) which one to enter my own plea.
-Printer bought about 2~3 weeks into Sept 2012
-Installed onto Macbook Pro running Lion (full updated at that time)
-Both wireless scanning from printer to computer and initiated from computer worked fine.
-Printer, with full choice of duplex, layout etc, worked fine. (Even left 5star feedback somewhere!)
-Set up eprint. That OK, too. Fine from iPad2 and SE Arc S printing photos.
-Somewhere along the line it stopped communicating with my MBP
-Out of interest, since there seemed to be no problems with an Acer laptop running Vista, I booted the MBP from an external drive on which I'd done a backup of my 10.6 system iMac (>300Km away: can't try that). Installed HP software from disc. Seemed fully functional. Odd. Very odd.
-Restarting with Lion on MBP, tried again. Looks as if it might work, but loses connectivity. Tried manual address on printer.
-Booting from 10.6 system again, reinstalled Lion on MBP (wondering if conflict between HP and Apple updates)
-Reinstalled HP software from disc.
Still didn't work.
-Brought Lion up to date. Downloaded most recent dmg file from HP. Looked for updates. Have applied firmware update to printer
8600 doesn't list my MBP as available computer to scan to
[But all the test pages done whilst in HP Utility, and others, get sent through]
Am getting rather fed-up with all this; never, ever before have I had so much printer problem.
There seem to be a number of Lion users out there with the same problem. So far -but very infrequently tried- other machines/systems seem OK, therefore I am coming to the conclusion that it is an Apple<> HP conflict. If not sorted soon the printer will be returned as it is not fit for purpose. I'll revert to using my seldom problematic, non duplex A3 Brother.
Hrumph
Please help, someone! Either with a pointer to something I've not yet tried or by analysis and rapid availablity of updated software.
Thanks,
Mike W

Officejet Pro 8600 - Macbook Pro and Macbook Air will not print

Products:
HP Officejet Pro 8600
Macbook Pro (Mac OS X, Version 10.7.5)
Macbook Air (OS X, Version 10.8.2)
Question:
Why did my Macs initially print fine, but now will not print at all?
Full Story:
I have a wireless network at my house that consisted of a 30mb cable internet, Netgear 900n, HP Officejet Pro 8600, 2 Dell Laptops with Windows 7, a Lenovo Laptop with Windows 7, and Dell Tower with Windows 7 - All printed just fine.
The HP Officejet 8600 was added to my network about 2 months ago.
I added a Macbook Pro and a Macbook Air about 3 weeks ago. Both Macs printed just fine for about a week. Then suddenly they stopped. I spent about 2 hours on the phone with HP Service, and they finally said it must be my router. So I called Netgear. Netgear was useless! They wanted me to agree to charges for services before they would even discuss the issue.
Due to information provided by HP's service support, and because Netgear will not support their product, I promptly purchased a new router - an Apple Airport Extreme.
The Macs recognize the printer, will print if hardwired via a USB cable, but will not print wirelessly to the Officejet Pro 8600. The PCs print fine.
The frustration that is being felt is compound by the fact that the Macs printed just fine with the Officejet Pro 8600 2 weeks ago, and now the printer just shows "idle"... even with a new router. (see image below)
Please help, I appreciate any support.
As a side note, the HP Service rep was very friendly, and definitely tried to support the HP Product, which is much more than I can say about Netgear.
Thank you,
This question was solved.
View Solution.

Hi,
More likely the issue related with Multicast, which Apple devices relies on to communicate with teh device through the network.
First try unplugging the router for 30 seconds.
Plug it back to the power and wait for 2-3 minutes.
Turn the HP printer Off and back On, then check for any difference.
If the same persists, try changing your router configuration as following
Note: the settings below are not related with the HP product, I provide you the steps as a best effor and those are only based on my own knowledge. you may try modifying the router settings at your own risk:
Open the router configuration page (can be found listed as the Default Gateway by clicking the Wireless icon on the printer, then print a network configuration report.
Click the Advanced tab.
Click the Setup option from the menu, then click on WAN Setup.
Make sure to uncheck the box next to Disable IGMP Proxying and Apply the changes.
Click the LAN Setup on the same Setup menu.
Set the RIP Version as RIP-2 and Apply the changes.
Reboot your router and then check for any change.
I hope you may find that information useful, you may also use the user guide below for further information:
http://www.downloads.netgear.com/files/GDC/WNDR4500/WNDR4500_UM_07DEC2011.pdf
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Officejet Pro 8600 Wireless Setup -Printing shows in Queue and then disappears. Not Printing

I just received the Officejet Pro 8600 as a gift and loaded the set up software and it on my wireless network. When I try to print an email or a coupon, the command goes to the printer and shows in the queue. Then after several seconds, the printing queue (job) disappears without printing the document. Does this command go through the HP ePrint function or the Network Officejet Pro 8600? It shows the HP ePrint as being on USB.
I've run all of the diagnostics, downloaded all of the new software, firmware and updates. I've spend many hours trying to get the printer to print.
Thank you for any help you can provide.
This question was solved.
View Solution.

Hi @bksechols
Welcome to the HP Support Forums. I understand that when you send a print job to your Officejet 8600 printer that it goes to the print queue and then disappears without the print job printing.
To better assist you, would you please provide some additional information?
How is the printer connected (USB cable, ethernet, or wireless)?
What operating system are you using?
Are all print jobs failing? If yes and you are using a Windows operating system, please Try the HP Print and Scan Doctor for Windows. The HP Print and Scan Doctor is a free utility (tool) that helps to quickly resolve common printing, scanning and connectivity issues.
When you send a print job are emailing the printer’s ePrint email address? If so please review The HP ePrint Print Job Did Not Print If you are sending the print job by using the print command, please review the Print Jobs from Your HP Printer are Stuck in the Print Queue document.
I look forward to hearing from you.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

My HP OfficeJet Pro 8600 won't connect to my wireless router

This is bizarre. I have had my HP OfficeJet Pro 8600 for about 6 months. It has generally worked fine, and we have used it wirelessly only. But now it refuses to connect to the router. It can FIND the router, and it can find other networks in the area, but it won't connect to the router. I ran the Wireless Network Test, and the results say:
Wireless On - Pass // Wireless Working - Pass //
Network Name (SSID) found - Pass // Wireless Networks Detected - 9
Printer Settings Consistent with Wireless Router Settings - Pass / No Filtering - FAIL //
So it recommends solution as follows: "1 If MAC Address filtering is enabled, and you would like to keep it enabled, you must add the Mac address of your printer to the list of permitted devices for your router before continuing."
Except, guess what, I don't have MAC Address filtering enabled. I wouldn't know how to do that, much less check for it.
Also, before today, this was never a problem. HELP!
Thanks....
If you are interested, here's more detail and background.
Before today, the only problem we have had is that frequently our Apple laptop (OS X 10.6) has trouble connecting to the printer. This has been odd because the printer is connected to the network, and so is the laptop, but the laptop can't find the printer - it thinks the printer is "offline" (even though it's not). Usually, if I wait a while, it will find the printer, and it will resolve itself work fine. If not, we sometimes have found that it can fix itself if you restart the laptop -- restarting the printer does not make a difference. In fact, I did exactly that today, and it resolved itself. And I printed. Fine, right?
But then I wanted to do more printing, and the problem of the laptop not finding the printer came up again, so I decided to really "get to the bottom of this." I don't remember exactly what I did, but somehow I was persuaded by the online help, that the correct solution would be to go into my System Preferences / Print and Fax, and click on the "-", which de-installs the printer, with the idea of re-installing the printer. But then when I tried to re-install the printer, it could not find the printer. Ugh! Wierdly, it found an 8600 Scanner, but not an 8600 printers. After installing and de-installing the 8600 scanner a few times, I eventually deinstalled everything, and I decided to start from scratch. I got my HP disk, and installed all the software again from the beginning (even though it was already there), and then it looked for my printer, but couldn't find it. So then I got a USB cord, and plugged that in.
So, now I have a situation where I do have a working printer via the USB cord, but no wireless connection at all. In particular, since the Office Jet Pro 8600 won't connect to the router, I don't know what else to do. My Apple MacBook pro is 2 feet away from the printer, and it is connected to the router just fine (as is my blackberry), and I have never before had a problem connecting to the wireless router by the printer.
Any suggestions?

There are two things that can trip the mac filtering test to fail: actual MAC address filtering setup (sounds like this is not the case) and using wireless channel 6 or automatic for wireless channel in the wireless network settings (in the router). Since it does show failed for MAC filtering and you do not use this option, try changing the wireless channel in the router to 1 or 11. Those two channels provide the best compatibility with printers due to less interference. Almost everything defaults to auto or 6 for the channel and this causes a lot of interference. This change should not affect anything at all. To do this, you may need to contact the router manufacturer as the process differs from router to router.
What brand and model is the router?
Has anything in the network settings changed at all?
What version is the Mac OS X? There may be additional steps to take as it sounds like there are two separate issues involved and this could be revisited later.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Intermittent wired network connection on HP OfficeJet Pro 8600

I've searched the forums and I haven't seen a problem/solution quite like I am experiencing, so I am starting a new thread.
I have a HP OfficeJet Pro 8600 that will only keep an intermittent connection to my router. Lately, it has been more often not than connected. I usually have to disconnect and connect the Ethernet cable to the back of the printer several times before it will show a connection, and then, only for a little while before it drops the connection again. When connected, everything works fine (printing, faxing, scanning).
When the printer is disconnected, the network status has a yield sign with an exclamation point inside. There are no blinking lights on the back where the network cable connects. When it connects (by me plugging and unplugging), the lights start flickering. I've tried several cables including known good ones to rule that possibility out. Cycling the power has no consistent affect. The router is otherwise working fine.
Here are other details that might help:
Model: HP OfficeJet Pro 8600 (N911a)
Firmware: up-to-date
Software drivers: up-to-date
Router: CISCO E3200
Connection: wired network
Static IP address reserved (not connecting with DHCP)
MAC filtering off
Main Computer: Windows 7 Service Pack 1
Wired Connection to the router
Can someone suggest a solution? My best guess is that the network card in the printer is bad, but I am willing to try an easier solution. Thanks.

Hi, are there any other peripherals using the RJ45 ports on the router?
Are you using a static IP address for the 8600?
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

Windows 7 / HP OfficeJet Pro 8600: Unsuccessful Network Installation

OS: Windows 7 Professional 64-bit
Printer: HP OfficeJet Pro 8600
My goal is to enable the "Scan to Computer" feature of my HP OfficeJet Pro 8600 on Windows 7, which doesn't find my computer when I try to use it from the printer's front panel touchscreen. The printer's connected to my local wifi network.
In the setup program on the included CD, I've opted NOT to install any software aside from the "HP OfficeJet Pro 8600 Basic Device Software", which installs fine. I also opt NOT to install the "ePrint" web services or allow it to connect to the network for updates or share usage statistics or any of that.
During the setup program, the "Network Check" correctly finds the printer on my local wifi network, but the following "Network Printer Installation" part always fails, resulting in "Unsuccessful Network Installation", no other details. The result is the same if I retry with Microsoft Security Essentials' "Real-time protection" off, or with Windows Firewall off. No other anti-virus is running.
The "HP Scan" program fails immediately with the error message "The HP OfficeJet Pro 8600 was not found."
Under Control Panel > "Devices and Printers" I see an HP OfficeJet Pro 8600. Windows installs and prints with this printer just fine without the provided CD.
Under Control Panel > "Device Manager" the printer is NOT listed under "Imaging Devices".
My Windows Image Acquisition (WIA) service is running.
Any clues?
This question was solved.
View Solution.

(I never managed to solve this, how did this get marked "Solved?")
I'd be happy with either means of starting a scan. Here are some things I've tried since my last post (sorry, I gave up on this for 2 months and am now trying to get it working again):
I've got the printer connected by USB as well as on the network, and running the software installer with the USB connection option just gets stuck forever at the "Connect the USB Cable" screen. The USB cable is connected.
Under "Scanner Actions" on the HP Printer Assistant application, clicking "Manage Scan to Computer" reports: "Scan to Computer is enabled. You can start a scan from the printer. Your computer is not listed as an available computer on the printer's control panel. Please restart your printer and try again." Tried restarting/unplugging the printer, but that doesn't change anything.
The HP Print and Scan Doctor's first screen reports the State as "Installed" for USB and "Not Installed" for the network. It returns these results for the various steps of "Fix Scanning":
Device Manager: Pass
Driver check: Fail ("The Scan driver is unable to communicate with the product.")
Windows (WIA) scan: Fail (no information given, other than instructions to reboot)
HP Twain scan: Fail ("Scanner communication cannot be established..." dialog)
Registry: Pass
HP Scan: Pass
Since my last post I've also updated the printer's firmware, which seemed to work fine. It's now on firmware version CLP1CN1304AR.
The Windows event log reports several warnings from the software installer saying "Failed to connect to server. Error: 0x800401F0" with Event ID 1015, is this important? Tried it again with Windows Firewall off for both public and private networks, no difference.

Unable to find network printer HP OfficeJet Pro 8600

HP Officejet Pro 8600
Windows 7 64bit
updated router firmware
Troubleshoot all item s listed by HP and with Windows
I have been unable to print wireless from my laptop. Wireless network test results gives me a pass in all categories. Network name is the same on printer and laptop. IP address on printer and tcp port are the same. Tried firewall on and off. AVG antivirus on and off. Unplugged printer, router, usb, restarted laptop. Nothing has solved the problem.
I can see that the printer has an ip address. My router has an ip address and my laptop has an ip address. Should they all be different? I am using the ip address from the printer to set up the wireless printing when asked to enter the address.
This has been the most frustrating process I have ever delt with. It should not be this difficult to set up. Please help.
Thank you in advance for a quick solution.

Shurlee, I want you to do is re-run the wireless setup wizard on your printer. Then uninstall it, and reinstall it again using the software I am going to link you to below. From what you describe it sounds like either an installation issue or an issue with your network. If this helps feel free to mark my post by hitting the star below my name which gives me a kudos - kinda like a job well done on here.
First if you use a USB cord, make sure to remove it. Do not plug it back in until the software directs you to. Then go through the Devices and Printers, Programs and Features and Device Manager folders and insure that all copies, files, and programs related to the printer are removed. Then as directed, restart the computer.
In the START menu type "%temp%" and press ENTER. Here I want you to press Ctrl+A and hit DELETE. Some of the files will not allow you to delete them, skip those files and delete the majority that allows it.
Download these files and install them. By the way these are for the N911a, but if you have the 8600 Plus or Premium you will need different drivers.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=4323659
Install that and let me know the result!
Have a great day!

HP Officejet Pro 8600 fax confirmation time and date fields has all zeros

Similar Messages

Maybe you are looking for