HP P6310f Hangs at Startup, Won't Recognize

Yesterday my HP p6310f running Windows 7 froze up.  I had no choice but to power it off.  When I powered it back on, it hung at the Start Up screen and none of the F keys would work to get into set up, boot menu, diags, etc.
I opened the case and moved the jumper to reset the CMOS.  This time when I booted it up, it came up to a repair screen.  I tried to run repair, which it said would take over an hour.  I left it running all night and this morning it had not finished and I powered it off again.  Now when it boots up it doesn't recongize any hard drive, any CD drive, nothing.  Sometimes it will let me in setup, sometime not, but when it does it does not recognize hard drive or CD drive so I can't use my restore discks.  I've reseated all the cables to no avail.  I'm suspecting a bad motherboard (Pegatron M2N78-LA), but before I shell out some big bucks to replace the motherboard was wondering if there are other troubleshooting tips I can try?  At least I want to make sure it is the motherbord before ordering.  Thanks for any help. 

suiramix wrote:
Today, I had  the same symptoms with HP P6310F desktop (14 months old), it will not pass HP splash screen ...tried reset CMOS, removed RAM, changed SATA cables and power supply ..Nothing except removing SATA cables from hard drive and DVD drive , the computer will boot normally and press F10 goes to BIOS setup. Connected external DVD drive using USB and boot up Linux Live CD without any problem !!!
At this point  I suspect a faulty SATA Controller (MCP 78S GeForce 8200 -AHCI rev.a2).
I will try to upgrade the BIOS from 5.14 to  5.16 !!
Any suggestions ???
I have 2 Hp P6310f  right now!! Both seem to have similar problems with start up!!
Unable to find Hard Drive or Boots fine then Freezes!!
I ran the diagnostic's tools (F9) an all pass!! Only after letting the system cool down though!
After a little more troubleshooting!!!  I have found that the south bridge gets extremely hot!!
If I then run the diagnostic's tools (F9)  i get an error (Unable to find boot device)!!
 If I let systems cool for awhile and then reboot They fire right up But then freeze up again when the chip gets hot.
I removed the heatsync an cleaned a reapplied some Artic Silver Didn't seem to help at all!!
The heat syncs are still extremely hot!!
So i don't know if this is the same problem others are having But this is what i have found so far!
Seems to be a problem with the Motherboard!!!

Similar Messages

  • IMac G5 hangs on startup, won't boot from disc

    Hello,
    My brother's computer has been acting up and I've been unable to fix it for him...so I was hoping I might be able to get some advice here.
    Problem: hangs on startup. It goes to the gray screen with the Apple logo and the spinning progress wheel like it normally would, but never gets past that. You can hear the hard drive working and eventually the fan comes on.
    What I've done:
    1) attempted to boot from OSX disc, same result
    2) attempted to boot from Apple hardware test disc. this brings up an open firmware terminal style prompt but does not boot from the disc. using the prompts i reset pram and did the "reset all" command which restarted the computer but it continued to hang
    3) opened it up and pulled the only ram chip out and put it in the other slot. Unfortunately we don't have another chip to test out, but if you guys think it is a likely culprit I'll go buy him one to see if that fixes it.
    Any advice will be appreciated. Thanks!
    -Alan

    Do you hear the drive spinning up? Have you tried a safe bootAfter the startup tone, hold down the <shift> key until you (hopefully) reach the desktop, it will be longer than normal, because Disk Utility's "repair" is invisibly run; it also will bypass any login items. If the system gets to the desktop OK this time but stalls when the shift key is NOT held down, the problem may be some login item that will need to be removed, using the Accounts panel of System Preferences and its Login Items section.
    You could try to repair the machine using Target Disk Mode to access it.

  • 2 things: iPhoto isn't automatically copying all my imported photos into an iPhoto album folder AND ever since i upgraded my MacBook 120GB to Snow Leopard, iTunes won't recognize my iPhone.

    So i have a 120GB MacBook that's about 4 years old (just updated to Snow Leopard--been working in Iraq, i'm a little behind).
    Never had a problem with it.
    I also have an iPhone 4 which i've had for about a year (up-to-date software as of about a month ago).
    Never had a problem with it.
    I've had iTunes for years of course (up-to-date).
    Never had a problem.
    1.
    Now my iTunes won't recognize my iPhone since the Snow Leopard update.
    iPhoto will recognize my phone, but iTunes won't.
    Went through all the preferrences and i can't find anything that isn't set properly.
    iTunes Helper is used during startup.
    Everything seems fine.
    Any help?
    2.
    I use a WD external hard drive to back my Mac up every week or so.
    I recently realized that half of my pictures from iPhoto are not copied to the external.
    They haven't been transfering over.
    So i snooped through my folders and as it turns out, iPhoto hasn't been copying the pictures i import from my iPhone to iPhoto and saving them as .jpg files in the pictures folder (or iPhoto album or whatever) like i think it's supposed to.
    My pictures folder has approx half of all my pictures in it, meaning at some point (probably 2 years ago) iPhoto stopped making the file copies of my imported pictures.
    I do not know why.
    No idea how to fix it.
    If i were able to fix that (with your help), would all the pictures that haven't been copied automatically copy to my pictures folder once i had the issue resolved or would there be a lot of dragging and dropping?
    I've been clumsily and sloppily copying all my pictures to a new folder on my desktop and manually transferring that folder to a thumb drive (which i keep in my pocket) and my external (just so i have them in some form) in case my computer crashes or a mortar shell lands on my room and blows my computer up.
    Can anyone please help me with any of this?
    I can't just stoll down to the Apple store to ask the Genius Bar (I'm in Baghdad) and i don't have Apple Care so no one will help me on the phone when i call Apple.
    Thanks so much.

    hey mill1640,
    Did you ever get your iPhone to register with iTunes? I just upgraded as well to Snow Leopard, and my my isn't recognized at all also.
    If you did get this resolved, I would appreciate a little suggestion in the right direction.
    Many thanks,
    Josh

  • Yoga 2 Pro won't recognize my Seagate external hard drive

    I have a Yoga 2 Pro that won't recognize my Seagate Backup Slim 2TB USB 3.0 external hard drive. 
    I ordered one from Amazon and it didn't recognize immediately when I plugged it in. The disk drive shows up in Devices and in Device manager with the Yellow caution triangle, but it never shows up in drives under my computer or in Disk Management (Where you change partitions, etc.)
    So I ordered a replacement from amazon, I thought it was broken. I had tried it in a different computer and the same thing happened so I assumed it was the drive. On a whim I tried it on the alternate machine again except this time I bypassed the USB hub and plugged it directly into USB 2.0, it worked!
    I installed a Paragon HFS+ software (it's for Mac Only Seagate drives to work with windows, even though this drive is NOT Mac only) and the installation failed, and my computer started messing up. It wouldn't completley power off nor restart. It just hung at the shutting down screen indefinitely. 
    Finally, I let the computer die, turned it back on, plugged in the hard drive and it worked. But I had already ordered the replacement. So I had to return the original and go tthe replacement and now it won't read at all. 
    Since I plugged it in, my computer will NEVER shut down, it will just sleep unless the battery dies, it won't restart either, it'll just hang at the restarting screen. 
    The drive still won't work, and the touchscreen doesn't work sometimes after a reboot. (Because I have to force shut it off everytime I want it off.)
    I went into power settings and turned everything on max power (To help my battery die faster) and even changed the USB power option thing to disabled. I still don't know how I got it to work that ONE time and now I'm stuck. Any help or advice?

    Oh I also had a message that came up when I tried to reconnect it to my comptuer. This is what the message stated:
    The disk you inserted was not readable by this computer.
    and my only options I have are
    Initialize..., Ignore, Eject
    what are my options of getting my data restored? I don't care so much about the drive, I am concern about my 2TB of data on there. Please anyone help me with this!!!!! I am open to suggestions to get my data back.

  • Mac won't recognize my password to let me download anything

    I recently downgraded from Yosemite Beta to Mountain Lion and now my mac won't recognize my login credentials. Curious thing is it does recognize them to let me login at startup. But it won't let me download anything because it says my password is wrong. I changed the password and again it recognized it to let me login but not to download anything. What's going on?

    Where are you trying to download from? Apple ID password?

  • Itunes won't recognize my ipod old or new one

    Itunes won't recognize my Ipod classic. It woudn't recognize the old one, Apple store said it was the Ipod so I bought a new one but it won't recognizethat one either

    Hello crickettspeed,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iPod not appearing in iTunes
    http://support.apple.com/kb/ts3716
    iPod: Appears in Windows but not in iTunes
    http://support.apple.com/kb/TS1363
    Try the iPod troubleshooting assistant:
    If you haven't already done so, try the steps in the iPod Troubleshooting Assistant (choose your iPod model from the list).
    If the issue remains after following your iPod's troubleshooting assistant, follow the steps below.
    2. Restart the iPod Service
    3. Restart the Apple Mobile Device Service
    4. Empty your Temp directory and restart
    5. Verify that the Apple Mobile Device USB Driver is installed
    6. Change your iPod's drive letter
    7. Remove and reinstall iTunes
    8. Disable conflicting System Services and Startup Items
    9. Update, Reconfigure, Disable, or Remove Security Software
    10. Deleting damaged or incorrect registry keys
    Best of luck,
    Mario

  • DVD Burner won't recognize discs

    I recently installed an lg gsa-4166b dual layer dvd burner to my emac and for some reason it won't recognize cds or dvds. Whenever I try to burn anything and put in a blank disc I get the message "no disk inserted". I'm running Mac OSX 10.4.11 and even installed the PatchBurn utility, but still no luck. Can someone help me?

    Oh really? Now that is interesting, because in fact I also have a Western Digital MyBook Pro external HD. Actually 2. They worked fine until the last month or so, and one of them had a bad disc so I had to have it replaced on warranty. Now the other one is acting strange -- won't mount. WD had me upgrade the firmware and reinstall the latest drivers. But it's still not acting right.
    And you are also correct about the disc playing. Normal DVD's, CD's and CD-ROMs play fine. It's just blank CD-R's etc that come up as "unreadable."
    I bought these two WD MyBook Pro 1 TB drives on 10/20/2007 however, and I don't recall that I had a disc burning problem that long ago. Maybe it's been that long since I burned a disc? I'm not sure...
    Incidentally I've had another problem for a really long time, which is a very long Mac OS startup. I am not sure when it started but it might have been about the time I bought these drives and installed the software. See threads:
    http://discussions.apple.com/thread.jspa?threadID=1765645&tstart=0
    and
    http://discussions.apple.com/thread.jspa?threadID=1880557&tstart=0
    Yesterday two things happened. One, Apple sent through another automatic update requiring a reboot, but I didn't catch what it was. Two, WD had me upgrade the drive firmware and software drivers. Suddenly my bootup problem has gone away. So the question is, was it Apple's update or WD's firmware upgrade?
    And lo and behold, I just entered one of the same blank Fujifilm CD-R discs and it mounts without a problem. I can now burn discs again. I have a feeling the WD firmware upgrade fixed a lot.
    Yeesh! I think I shall be buying drives from someone else in the future.
    Thanks for this very insightful tip.

  • G4 DVD drive won't recognize OS 10.4 upgrade disc

    I have a a PowerMac G4 (AGP graphics) with a CPU type PowerPC G4 (2.9). I have a upgrade disc for OS 10.4. When I load it into my Quantam Fireballlp LM27.3 DVD drive, the drive won't recognize the disc. It attempts to read it and then ejects it. I have an external USB 2.0 DVD RW burner plugged into a USB 1.0 port, and it recognizes the disc, but I can't select it as the startup disc.
    How do I get my system to read the upgrade disc so I can upgrade to OS 10.4? I've run a lens cleaner several times with no change.
    Thanks!

    Hi-
    Well, if you know someone who has a Mac, or, if you have another machine, try the disc in another machine. There is a possibility that the disc itself is bad. I would consider this a strong possibility, since the drive recognizes other DVD's, and the Panther install disc.
    If the disc tests good in another machine, then you will need to consider replacing the drive for a newer model. A new combo drive is only about $30-$40. The Pioneer DVR-112 would be a good consideration.
    http://eshop.macsales.com/item/Pioneer/DVR112DBK/
    As for the "helpful" not working, there seems to be a problem within the system (known by the hosts, yet allowed to continue....). For now, I will gladly accept your thanks! (and, you're welcome!)

  • My mac won't recognize my external hardrive!!

    I have a Maxtor One Touch II 300GB external hardrive with all of my pics and backups, and ever since I installed Leopard it won't recognize the drive. I've read other forums and know it's because it's password protected and Seagate or Apple has come up with a solution yet. So I did the only other thing I could...re-install Tiger with my backup disc which was 10.4.7 for my Mac mini Intel. Now it still won't recognize the drive! The software doesn't automatically startup and even after starting it manually it doesn't recognize. I'm guessing because when I re-installed Tiger and it asked me to archive the newer version it must have kept the same coding or whatever. I don't know much about coding so I'm lost there. I have my Powerbook G4 with Leopard on it, but of course it won't recognize that drive on there either. Right now I have a few options I could re-install Tiger on my powerbook and erase everything, but I can't find the install disk and I'm not sure the install disk from the Mac-mini will work because it's for the Intel processor hopefully that won't matter. Another option is to try and see if my wife's HP with Vista will recognize it, but the drive is formatted for Mac so I'm not sure if it'll work and ask for a password. I'm stuck at frustrated right now...if I could just get a computer to recognize it, take the password off... I would shell out the money to get a new drive recognizable by Leopard and transfer the data over. I DO NOT WANT TO ERASE THIS DRIVE!! I know it still works, but I can't access it.  Anyone got any ideas?

    Follow the instructions in the section of this FAQ which is relevant to your situation.
    (21534)

  • Ipod shows folder with exclamation point and computer won't recognize

    My ipod resets itself each time that I try to turn it on, and then flashes the folder with the exclamation point. I have tried to restore it and update software but the computer won't recognize it. A few days before it broke the ipod would skip through some songs that it was unable to play for some reason, and now it makes a clicking sound when trying to start up. Did it die, or is there a way to fix this?

    Hello,
    If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
    http://docs.info.apple.com/article.html?artnum=60983
    If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
    Make sure you do all the following “TRYs”
    A. Try to wait 30 minutes while iPod is charging.
    B. Try another FireWire or USB through Dock Connector cable.
    C. Try another FireWire or USB port on your computer .
    D. Try to disconnect all devices from your computer's FireWire and USB ports.
    E. Try to download and install the latest version of iPod software and iTunes
    http://www.apple.com/ipod/download/
    http://www.apple.com/itunes/download/
    F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
    http://www.apple.com/support/ipod/five_rs/
    G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
    http://docs.info.apple.com/article.html?artnum=93651
    If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
    Intermediate Level
    A. Try to connect your iPod with another computer with the iPod updater pre-installed.
    B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
    For Mac computer
    1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
    2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
    3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
    4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
    5. Eject your iPod and do a Reset
    6. Open the iPod Updater and click “Restore”
    For Window computer
    Go to folder “My Computer”
    Hope you can see your iPod there and right click on the iPod
    Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
    Now select “Format”
    Eject your iPod and do a Reset
    Open the iPod Updater and click “Restore”
    In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
    C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
    Tips
    a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
    b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
    c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
    Advance Level
    A. Diagnostic mode solution
    If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
    You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
    Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
    iPod 1G to 3G: "Menu" and "Play/Pause"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
    The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
    iPod 1G to 3G: "REW", "FFW" and "Select"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
    You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
    Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
    B. Format your iPod with a start disk
    I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
    If none of these steps address the issue, your iPod may need to be repaired.
    Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
    Or visit your local Apple Retail Store http://www.apple.com/retail/
    In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
    http://www.ipodresq.com/index.php
    Just in case that you are at the following situation
    Your iPod warranty is expired
    You don’t want to pay any service charges
    You are prepared to buy a new one
    You can’t accept the re-sell value of your broken iPod
    Rather than leave your iPod as paper-weight or throw it away.
    You can try the following, but again, only do it as your last resort and at your own risk.
    Warning ! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
    Last Resort Level
    1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
    In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery replacement (with pictures)
    http://www.kokopellimusic.us/KM_instructions.htm
    Have I tried this myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
    2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
    Strange error on iPod (probably death)
    http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
    Sad Face on iPod for no apparent reason
    http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
    Meeting the Sad iPod icon
    http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
    Sad faced iPod, but my computer won’t recognize it?
    http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
    iPod Photo: unhappy icon + warranty question
    http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
    4th Gen iPod Users - are we all having the same problem?
    http://discussions.apple.com/message.jspa?messageID=2235623#2235623
    Low Battery, and clicking sounds
    http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
    Sad faced iPod, but my computer won’t recognize it
    http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
    I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.

  • G5 won't recognize install disc after formatting

    Hi all,
    I recently found a G5 tower at my work that wasn't being used. It had a Debian on it so I formatted it with my OS 10.4 disc in order to install tiger but now it won't recognize any kind of startup disc.
    When I turn on the comp and hold option it gives me the window where I can choose my startup disc, but no disc is ever found. When I start the computer up with out hitting any keys or holding C it just gives me a globe icon and never finishes booting.
    Am I doing something wrong?
    Mike

    Hi BDAqua and thanks for the suggestions,
    the CMD-OPT -SHIFT-DEL key combo didn't seem to have any affect on the computer, and I'm not sure what a firmware password is.
    I actually have a couple of install discs, one for 10.3.5 that has the 2Z691 numbering on it, and another for 10.3.7 that has a 691.... numbering on it. I'm not sure which of these came with the computer but they both say power mac g5 on them and neither of them has worked so far. I've also tried using a debian for ppc install disc with no luck on that either.
    When I start the computer up it'll either show me a folder with a question mark or square with a globe in it, and when I hold option it'll look for a drive to start from but will never find one.

  • Harddrive was replaced and now my computer won't recognize the IPOD

    I recently had the hardrive replaced and now I can't seem to get it to charge, my itunes to recognize the ipod. I have tried several times restore and update. All I get is error messages "install wizard could not be completed" and "error in update manager". One thing...I have the IPOD with the color display and when I got it back and plugged it in (it worked long enough to download my music, but the display was in black and white. When I do get something on the screen it is a file with an exclaimation point and the www.apple.com/support/ipod website. HELP!!!!!

    Hi,
    A colour iPod without a workable system files, will display in play and white. I suggest that you should do a format first, before the Restore.
    Please read the following for some suggestions
    Hello,
    If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
    http://docs.info.apple.com/article.html?artnum=60983
    If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
    Make sure you do all the following “TRYs”
    A. Try to wait 30 minutes while iPod is charging.
    B. Try another FireWire or USB through Dock Connector cable.
    C. Try another FireWire or USB port on your computer .
    D. Try to disconnect all devices from your computer's FireWire and USB ports.
    E. Try to download and install the latest version of iPod software and iTunes
    http://www.apple.com/ipod/download/
    http://www.apple.com/itunes/download/
    F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
    http://www.apple.com/support/ipod/five_rs/
    G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
    http://docs.info.apple.com/article.html?artnum=93651
    If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
    Intermediate Level
    A. Try to connect your iPod with another computer with the iPod updater pre-installed.
    B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
    For Mac computer
    1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
    2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
    3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
    4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
    5. Eject your iPod and do a Reset
    6. Open the iPod Updater and click “Restore”
    For Window computer
    Go to folder “My Computer”
    Hope you can see your iPod there and right click on the iPod
    Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
    Now select “Format”
    Eject your iPod and do a Reset
    Open the iPod Updater and click “Restore”
    In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
    C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
    Tips
    a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
    b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
    c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
    http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
    Advance Level
    A. Diagnostic mode solution
    If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
    You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
    Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
    iPod 1G to 3G: "Menu" and "Play/Pause"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
    The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
    iPod 1G to 3G: "REW", "FFW" and "Select"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
    You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
    Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
    B. Format your iPod with a start disk
    I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
    If none of these steps address the issue, your iPod may need to be repaired.
    Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
    Or visit your local Apple Retail Store http://www.apple.com/retail/
    In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
    http://www.ipodresq.com/index.php
    Just in case that you are at the following situation
    Your iPod warranty is expired
    You don’t want to pay any service charges
    You are prepared to buy a new one
    You can’t accept the re-sell value of your broken iPod
    Rather than leave your iPod as paper-weight or throw it away.
    You can try the following, but again, only do it as your last resort and at your own risk.
    Warning ! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
    Last Resort Level
    1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
    In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
    http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
    2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
    http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
    Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
    2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
    What should I do with my iPod? Send it or keep it?
    http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
    Strange error on iPod (probably death)
    http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
    Sad Face on iPod for no apparent reason
    http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
    Meeting the Sad iPod icon
    http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
    Sad faced iPod, but my computer won’t recognize it?
    http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
    iPod Photo: unhappy icon + warranty question
    http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
    4th Gen iPod Users - are we all having the same problem?
    http://discussions.apple.com/message.jspa?messageID=2235623#2235623
    Low Battery, and clicking sounds
    http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
    Sad faced iPod, but my computer won’t recognize it
    http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
    Sad iPod solution
    http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
    Re: try to restore ipod and it says "can't mount ipod"
    http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
    iPod making clicking noise and is frozen
    http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
    I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.

  • Reader 9 won't recognize printer

    I just installed Reader 9 on my system (Vista Home Premium), and now I can't print anything because Reader won't recognize my printer. I get this error message whenever I try to print:
    Before you can perform print-related tasks such as page setup or printing a document, you must first install a printer.
    I did not get this kind of behavior from Reader 8, so I must assume there's a major error or bug in the code that's causing this. My printer (an Epson Stylus CX4800) is properly installed and works for all other apps but this one. Has anybody else experienced this on their systems?
    I'm using Reader 9.0.0 for Windows Vista with Vista Home Premium (SP1).

    No good. Did a nozzle check and head cleaning through printer properties while in Reader, and it still refuses to recognize the printer. Not only that, but for some reason it defaults to XPS Document Writer as the main print option at startup, and I can't change that to stay with the Epson instead. This is very puzzling and rather annoying, since I'm now without a print capability until they decide to do a bugfix update.

  • Had to reinstall Panther - now CD won't recognize OS9 disks

    I have a B&W G3 with 2 hard drives in it. Had to replace the larger of the two, and of course it was the one with my startup system (or one of them.) I could boot from my 9.2 startup disk which was on the other hard drive. I made a copy, using the disk utility restore function, on to a backup drive so that I didn't lose everything on the crashed disk. Then I replaced the hard drive, partitioned it and reinstalled Panther all the way to the most recent update. I was able to capture just about 98% of all of my previous system setting, extensions, etc., yet now when I put in an older CD (that was comaptible with OS9) it says it is "unrecognizable" and wants to inititialize or eject. When I go to system profiler it says there is no OS9 drivers for the CD. It is the original CD ROM from Apple, a matshita CDR. How can I recapture the driver? Where would it be?

    Daisy:
    Since you already have everything in place on separate partitions, and it is so much of a hassle moving stuff around, I suggest you leave things alone until you need to something by way of re-installation.
    In terms of backing up a firewire external HDD would be prefereable as you could then use SuperDuper or Carbon Copy Cloner to clone to the firewire external, which you can then use as an emergency startup drive. It makes backing up a lot easier. SuperDuper is very easy to use and efficient. CCC works well, too, but is slightly more complex.
    Re: Had to reinstall Panther - now CD won't recognize OS9 disks
    Posted: Aug 22, 2007 11:05 AM
    So, Cornelius, what you are saying is that I am making it harder for things to function smoothly? The reason I have been doing the partitions is to save time when running something like Disk Utility. It goes a lot faster on a 20GB than it would on a 100GB, or am I wrong in assuming that?
    Now I have the daunting task of removing everything that I have finally gotten in place to the backup drive, and reformatting my MAC! UGH! Is there an easy way to do this without re-installing the major programs I use? When I was getting the data off of the previous bad drive, I dragged and dropped them onto the backup disk (a Simpletech 160GB USB) and that was very time consuming. I think it was slow because I have the old USB 1.1 and the backup is a USB 2.0. I did not use the backup software that came with it, because I was in panic mode and accidentally erased the program when I formatted the backup drive. Now I have it, but haven't used it yet. Even so, I was able to drag and drop most of the files and it worked fine, but I had to reinstall the OSX, QuarkXpress, and Indesign. This has been going on for a couple weeks and I am still tweaking things to get it right.
    When I used the "restore" function it put the drive on the backup but not in a folder. When I dragged and dropped it went across like folders. Do you have any advice for me to make this less painful?
    +One more point - if I did use the install OS9 drivers the first time, and it didn't, what would it do if it was only one partition? Would I get them back or not?+
    You can check to see if the OS 9 drivers are installed by going to Apple Menu > About this Mac > More info > Hardware > ATA. In the lower section of the main panel go down the list and look for OS 9 drivers installed. It will say yes, or no.
    Good luck.
    cornelius

  • Circle with slash/won't recognize DVD or external drives

    I have this model:
    Model Name:          MacBook Pro
      Model Identifier:          MacBookPro5,5
      Processor Name:          Intel Core 2 Duo
      Processor Speed:          2.26 GHz
      Number Of Processors:          1
      Total Number Of Cores:          2
      L2 Cache:          3 MB
      Memory:          8 GB
      Bus Speed:          1.07 GHz
      Boot ROM Version:          MBP55.00AC.B03
      SMC Version (system):          1.47f2
      Serial Number (system):          7304001D66D
      Hardware UUID:          134FD99D-DF06-5912-A8B9-255280C48DCC
    It often fails to boot with the circle with slash. Tried safe boot (works), tried booting from optical drive with original system disc (won't recognize or eject-tried all of the eject techniques), and ran disk repair in target mode (found nothig wrong). Can't run hardware check for obvious reasons. It does not see external drives connected to FW or USB ports.I am starting to suspect a bad logic board. Any thoughts?

    I can no longer startup from a CD/DVD
    Be sure you're inserting the DVD that came with your Mac Pro. If you are trying to boot from other optical media be sure it is compatible with Intel Macs and specifically the Mac Pro. You are probably trying to boot off a discs that does not have a suitable OS on it.
    or my external FW drive which has 10.4.8 also installed on it (pre-intel)
    Same goes here. Your FireWire drive does not have a suitable OS installed in it. You need to install an Intel version of Mac OS X. Additionally you will probably need to repartition your drive using the GUID Partition Table. Until you do both of these Startup Disk will not let you select it.

Maybe you are looking for