HP Pavilion DV6750er Laptop no longer go into passive cooling

After flashing BIOS version F.58A laptop stopped completely disable the cooler cooling, although the laptop cool and clean heatsink (tested). Can I get an older version of firmware, when the notebook works better for power.
Laptop has less to operate from the battery. Please Put a previous version of BIOS, for me it is very important.
Intel Core 2 Duo Wi-fi Intel 3945ABG NVIDIA GF8400GS

Hi,
If the battery of the HP laptop is not in a good condition, sometimes booting problems might happen. To remove any static charges accumulated in the battery, you would have to remove the battery and press the Power button for about 25-35 seconds. Then reset the battery. Even after this, if your laptop is not booting up then you could perform the battery calibration and press F8 key to boot in safe mode.
Get more information to fix Hp laptop booting issues :
http://supportforhp.iyogi.com/laptop-not-booting.html
Hope this information helps you.
Set peace of mind as your highest goal,and organize your life around it.

Similar Messages

Pavilion dv6885se Laptop Has a Blank Screen

Hello,
Having a problem woth my laptop. First the PC specs.
HP Pavilion dv6885se laptop
Intel Core 2 Duo T8100 @2.10Ghz
Vista Home Premium 32-bit
250GB HD
NVIDIA GeForce 8400M GS Video
Starting yesterday (1/8), the laptop would not boot up. It shows a blue screen (not Blue Screen of Death) that gives the option to repair or restore the system. I chose to repair because the restore was going to wipe the hard drive clean and reinstall the base system (factory specs).
I did this numerous times until finally at startup, I pressed the ESC key. Then there was only a black screen. Powering off and back on left the system in the same state: It was on, but no video. I connected the laptop to an external monitor, but still no video. Then after power off/power on a few more times, the screen came up all white. I watched the screen a few minutes and noticed that it was slowly “drawing” multiple colored lines vertically on the screen.
I went to hp.com to search for help. I did see one bit of help. The thread stated something about “crashing the BIOS”. To reset it, power off the laptop. press and hold the ESC key before powering back on. This restored the video somewhat. I was able to see the screen on the external monitor. I was back to the blue screen with options. I did the repair option numerous times and rebooted numerous times until finally the system was up and running.
While the laptop was still connected to the external monitor, tried changing some of the display settings. During all of this time while the laptop was plugged into the monitor, the laptop lid was closed. I just happened to open the lid, and the laptop screen came on. The laptop screen would never come on after power on, but would come on after changing display options and opening the lid.
Today, that no longer works the laptop is on, but the only video is using the external monitor.
Any ideas on what this could be? Also, if it is the laptop screen, would it be better to get it fixed or replace the laptop? Thank you.
Warmest regards,
Fred Tolan

Hello fredtolan.
This sounds like you may be experiencing a GPU issue or a larger motherboard issue. The fact that you're having display issues on both the integrated and external monitors would point to this.
Had you experienced any other problems prior to this? BSODs or freezes?
I would like you to perform a hard reset first. This reinitializes the hardware and can solve a wide range of issues. Try the following.
Shut down the notebook.
Remove battery and AC power.
Press and hold power button for 15-20 seconds three times.
Replace battery and AC power.
Attempt to boot notebook and post the result.
I would also like you to test the RAM and hard drive using the built in diagnostics. You may not be able to do this as I'm not sure if the pre-Windows loading screens will display on the external monitor. Follow the steps in this document and make sure to post the results if you're able to run the tests.
I hope you have a great weekend!
Please click the white star under my name to give me Kudos as a way to say "Thanks!"
Click the "Accept as Solution" button if I resolve your issue.

Hard drive not recognized on startup. hp pavilion ze4900 laptop

Receive the following screen message when I try to start. hp pavilion ze4900 laptop
Intel UNDI, PXE-2.0 (build 082)
Copyright (C) 1997-2000 Intel Corporation
For Realtek RTL8139(X)/8130/810X PCI Fast Ethernet Controller v2.13 (020326)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.
What does this mean?
Did you find an answer to this problem?

It means the hard drive has likely died. It is going past where the hard drive would be in the boot order into network (PXE) boot. To double check, tap F10 as you power up and see if you can find the hdd in the BIOS. If not you just need a new hdd.

Laptop no longer recognizing songs in external hard drive. Only ones in internal hd. Says file cannot be found and exclamation pt. to left of song.

My laptop no longer recognizes my songs in the external hard drive. It still plays the ones stored on my internal hd fine. It's just started doing this.
The song's names still appear in the music library, but when I try to play the song, anexclamation pt. comes up to the left of the title, and it says the file cannot be located.
OS is Windows 7 Home Premium
Thanks.

PhilinGood wrote:
Thank you Tal, sounds like a nice resolution of the username difference problem, i will try this as soon as i get home, but are you sure this will not duplicate all the exhisting songs in my library? Most of my songs were renamed/rated and have a "number of times played" number, which does matter in most of my smart-playlists...
Thank you in advance.
When I tried my suggestion, I had around 3 three separate folders on my computer which had music in them. The music in these folders was dragged and dropped into iTunes when I was adding it onto my iPhone.
I had foolishly moved some of the music from the other folders and into the music/iTunes folder iTunes then showed the exclamation mark beside these tracks and showed the not found or words to that affect window/popup. I then placed the folders (that contain the music) back to their location which there were at when I originally dragged and dropped them into iTunes, after this the exclamation mark and the not found window naturally did not appear anymore.
I then done the following:
iTunes 9:
Choose File > Library > Organize Library.
A message will pop up.
Place a check next to "Consolidate files" and click OK.
After I had done this, all the folders that contained the music that were in the 3 separate folders, were then placed in one folder, which in my case was,
C:\Users\MY USERNAME\Music\iTunes\My iPhone\iTunes Media\Music
Sometimes (depending on the device) it can be (your username)/music/iTunes/iTunes music

Pavilion dv4405nr laptop hard drive and recovery

Hi,
My daughter's Pavilion dv4405nr laptop's HDD (Samsung MP0804H Spinpoint M Series 80GB) is dead. It doesn't boot, and BOIS HDD test gives error 7. I took the HDD out, and connected it to several PCs (home, work) using two HDD universal adapters (like a BYTECC, and a NewTech) I left it spinning for about 6 hours. The PC sees the mass storage device, but it never shows up in MyComputer with a letter assigned. By right-clicking the working HDD and checking its properties, it lists all HDDs and I can see the damaged one listed w/o a letter assigned. I click to load volume information but all displays zeroes. I downloaded a Seagate-Samung utility to test the drive, and got the same error I had gotten with the laptop's BIOS utility.
Can this HDD be recovered? Is there a utility that can recover it?
If the answer is no: I connected the HDD back into the laptop, and set the boot sequence to DVD drive. I inserted the "All-In-One Recovery DVDs" for this laptop, but they didn't boot. Aren't the recovery DVDs bootable?
Your help and suggestions will be greatly appreciated.
Sincerely,
Richard

It looks like this unit came with Windows XP. It really depends on when in XP's production cycle the unit was released on how recovery works.
I am afraid the HDD is beyond salavaging at this point and the hard drive will need to be replaced. The recovery more than likely will fail on the bad HDD.
Early units came with recovery disks, one of which was labeled Operating System, and some used the F10 recovery and required making the recovery disks using a program (these units did not come with disks).
Is there a disk labeled as Operating System or Disk 1 of X?
If it is Disk 1 of X, then you would start with it, but start with Operating System if there is one labeled that.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

On my iphone 5s, in "photos" when I touch to enlarge, random new photos taken with 5s appear as old photos taken with 4 years ago - that aren't even on the laptop that I plug into. How do I correct this?

On my iphone 5s, in "photos" when I touch to enlarge, random new photos are showing as old photos. For example, let's say I'm looking in an album at a photo of a dog I took today. If I touch to enlarge- that photo of a dog is suddenly a photo of a family member taken three years ago (on my old iphone 4). This is random and has happened to about a dozen photos. This has caused me to accidently delete new photos thinking they were old ones until I figured out this was some sort of glitch. The old photos that are posing as new photos aren't even on my laptop that I plug into - they've been on my external hard drive for awhile so I don't even know how they're linking! Any suggestions??

I've tried both ways. My Computer locates the device but doesn't see the old photos, only listing the new photos.
I no longer have the iphone3; I just transferred the photos from the 3 to the 4.
Was there a format change or file type change or did the transfer process create something different? I can still see and access the old photos if I go to that album on the phone. But that's the only place where I can see them or access them.

HP Pavilion G6 Laptop Stuck on 0%

Hello, I have recently encountered a major problem in charging my HP Pavilion G6 laptop. I had not been using my laptop for a week as I had been using it frequently beforehand. I charged it and when I booted it up it said it had 0% while it was still connected to the charger. I left to to charge for longer and even though it said it was charging, the laptop remained on 0% of power. It still works (Very slowly now), but if I remove the charger the laptop immediatly shuts down due to it displaying that I have 0% of charge. I assume the problem lies with the battery, but before I buy a new battery I'd just like to know if this problem can be explained and can it be solved with a more practical method? Thank you.

Hi there, glad you posted your question here before buying another battery. From what I've found, there are still a few steps you can try first
Please take a look through this whole guide, hopefully it'll help kickstart that battery and the connections back to life:
Battery Does not Power Notebook or Hold a Charge
*** If my reply was helpful, please click on the "Kudos Thumbs-Up" on the right, as a way to say "Thanks!".
If this reply also fixed your issue - please click the "Accept as Solution" button, so that others can find the same answer. ***

WHY won't my Photo Stream pictures load to my Dell laptop any longer???

WHY won't my Photo Stream pictures load to my Dell laptop any longer??? All my settings seem to be correct...this is driving me crazy! Can anyone HELP?! This has been going on since Nov. 1st.

My photos used to automatically load to my dell laptop from my phone into My Photo Stream. Now they do not. I havenever had this problem before.
Yes, yes and yes.

Forgotten my BIOS password on my hp Pavilion dv2718 laptop!

I have forgotten my BIOS password on my hp Pavilion dv2718us laptop. When I access Setup through F2 and then try three times unsuccessfully, I get code 08653. The specifics of my laptop are:
HP Pavilion dv2718us laptop
Phoenix BIOS ID F.27 11/27/2008
Windows Vista Home Premium 32-bit SP2
Please help ... gww
This question was solved.
View Solution.

Decided to go ahead and pull the CMOS battery and clear the password which worked fine. When I went into the BIOS, I realized that the first password given me - (generic Phoenix) pkxdirv actually worked because I had pressed F2 and not F10. F2 apparently only brings up the Diagnostics part of the setup, at least on this laptop. Thanks for the help ...

Hi, I have a HP pavilion dv4 laptop computer. My E:\ CDDVDW TS-L633M cd drive has stopped working

Hi I have a HP Pavilion Dv4 laptop computer. My E:\ CDDVDW TS-L633M cd drive has stopped working. When I insert a new CD or an exiting cd into the cd drive, the computer displays a message to insert a cd into the drive. i Know that the cd that I'm inserting into the drive should be readable, but the computer doesn't recognize it. When I run the HP support assistant, and choose the HP Optical Disc Drive Check, I get the message "Insert media in : E:\ hp CDDVDW TS-L633M
If you want to do write testing, insert blank writeable media, Otherwise, read-only testing will be performed. When I insert a disk with a program that I want to install on the computer into the cd drive and click the next button, I get a window that says:
"Media Identification:
Wait while the media is being Identified."
Then another window is displayed with the message:
"Media Identification
No disc has been detected."
But I know that the disk is formatted correctly for my cd reader to recognize it.
Please Help,
-Ron

Hi Ron,
First, try the automated fixit from Microsoft on the link below.
Windows 7
Vista
Check if the drive is now working.
If the drive is not working, click the Start Menu, open the Control Panel and click on Device Manager. Next click to open DVD/CD-ROM Drives. Right click the drive and select uninstall. Do not delete drivers if asked. When the device has uninstalled click on the 'Scan for Hardware Changes' icon ( usually just below Help on the toolbar ). Let windows reinstall the drive and see if it now works.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

My HP Pavilion dv5 laptop

On my HP Pavilion dv5 laptop MY 2ND HP LAPTOP..NEVER AGAIN.I went to log in two weeks ago and it has a blue hallo screen saying trying to load files...I put out the word and was told it was NOT the hard drive (this time) I got a virus, this person got me back my Windows 7 , however, I do not see my HP icons, or tool bar or any info AT ALL ABOUT HP, How do I download all of my HP tools and software, such as my WEBCAM????? Also, I now notice that while typing all of a sudden the cursers stops flashing and it falls back into the body of my typing and starts my typing back somewhere else ...VERY STRANGE...Can any one help me????I sure would appreciate any help....Thank you in advance.....Signed CHRISTL

Why are you blaming HP for a virus and improper recovery of Windows 7?
How to properly recover a HP Notebook
If you did not make your HP recovery media, You can order recovery media here
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00810334&cc=us&lc=en&dlc=en

Hp pavilion dv6 laptop black screen

Hi all please is any one help me I have my hp pavilion dv6 laptop.
The laptop is working,have the necessary sounds after i
turn it on,but the problem is that the screen stays always black
..I connect the laptop to external monitor and it shows that everything is working properly. But It not working on laptop screen what should I do heplllllll

Hi
I'll try helping you with this,
You'll have to give it for repair - display assembly replacement. The display panel might be at fault here as your system works good when connected to external monitor.
But before that,
Do a hard reset first --
Turn off the computer by pressing SHIFT KEY while you click SHUT DOWN.
Remove the computer from any port replicator or docking station.
Disconnect all external connected peripheral devices such as USB storage devices, external displays, and printers.
Unplug the AC adapter from the computer, shut down system.
Remove the battery from the battery compartment.
Press and hold down the Power button for about 15 seconds to drain any residual electrical charge from the capacitors that protect the memory.
Insert the battery and plug the AC adapter back into the notebook computer, but do not connect any of the peripheral devices.
Press the Power button to turn on the computer.
Next:
To confirm, connect it to other monitor & do a full extensive hard drive & memory test from BIOS, tap quickly F2 or F10 soon after powering on the system.
If all tests are passed, contact HP service center.
thanks,
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

My HP Pavilion dv6 laptop wont turn on

My HP Pavilion dv6 laptop does not turn on. Problem with my laptop started couple weeks ago. At that time, when computer goes to sleep mode after inactive for some time, power light and led lights stays on but screen is black. I can not do anything else but to press power button for few second and force turn off. If I turn on computer right away then computer will have black screen and nothing happens. If I remove battery and wait for few minutes and connect the power cord directly to computer and turn on then it will turn on normally and work until it goes back to sleep again. But now, its not even turning on at all. So far I tried hard reset, plugged in to different monitor and RAM test but no luck. Again when I turn on, caps lock and num lock lights blink and fan turns on and power lights, volume lights and wifi lights stays on but nothing on screen. Thank you in advance for any help.

Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP Pavilion dv6 Notebook and having issues with performance. Here is a link to computer will not start. I would start at the top and work my way down. Mine was fixed with reseating the HDD. Others have had it fixed with just reseating the Memory. Here is a video that shows you how to remove and reseat the HDD and memory. Please note remove any and all USB devices. Disconnect all non-essential devices, as these could cause some issues. You could reset the BIOS with this document selecting the reloading the BIOS default settings. Which has helped others as it restores the default settings. Plug the power adapter directly into a functioning wall outlet. Do not plug it into a power strip, surge protector, or secondary power source as this could cause and issue. Please let me know how this goes. Thanks.

How do I best integrate existing laptops for a new server? Can I use the existing home folders on the laptops and make them into Network Users?

How do I best integrate existing laptops for a new server? Can I use the existing home folders on the laptops and make them into Network Users?

Yes it will work. I've done it for a few users in my small office. As with anything, there are quirks that you may or may not experience. Most quirks are app-related, due to app developers hard-coding absolute paths into their apps for things like temp files (Photoshop). Strategies for resolving these sorts of quirks can be found via google. You would probably have seen these quirks already when using server-based home folders for your kids. If you haven't noticed them, then you're probably fine.
The tech note you cited should be fine. It doesn't explicitly say so, but you'll need to enable ssh on your server, at least temporarily, so you can upload your home folder to the server using scp, rsync, etc. Don't try to copy the files up to the server via Finder.
Once all your files are transferred to the server and in the right place, make sure to chown them on the server, so they are owned by the userID you created for yourself on the server.
As with anything this involved, make a good backup of your laptop first.
Note I have one user that isn't too happy with the responsiveness of the periodic mobile home syncing. She has about a decade of e-mail in her home folder, probably 50 to 100 emails per day, many with attachments. Mobile home syncing takes a long time to check and sync this huge tree of itty-bitty files, eevn with server-side file tracking turned on. The other users are happy.
The nice thing about mobile home syncing is that when a user "graduates" to an age where they've earned their own laptop, you can change them from a server home user to a mobile home user, with a minimum of fuss. Also, if you lose or break a laptop, you can add a new replacement laptop to your network, and pull-down a replica of the home folder from the server, with almost no downtime.

I can no longer log into my ichat linked to my gmail. right after opening up ichat, receive the following message: lost connection with jabber. the server has unexpectedly disconnected.

i can no longer log into my ichat linked to my gmail. right after opening up ichat, receive the following message: lost connection with jabber. the server has unexpectedly disconnected. how to troubleshoot? thanks.

Hi,
There can be many reasons why the Login is "up the creek".
Any break in the network at your end whilst logged in will cause an issue.
A sort of discrepancy between what iChat thinks the state should be and what the server thinks.
If they don't agree the server will refuse to accept.
A Crash at the server end which does not log you out properly will also do it.
Any file at any time can be come corrupted.
Luckily with the iChat .plists they are recreated if removed with an iChat Restart.
If it were AIM you can also get your Account Suspended and this will not log you in.
(It tends to happen from Chat rooms where people notify AIM about bad behaviour (as they see it) and you have to apply to get Un-suspended).
Most of the big IM services use multiple servers.
Sometimes these go out of Sync.
In the case of AIM this happens when they remove Old unused Screen Names from people's Buddy List prior to making them available for re-registration. I am not sure if this happens at Google.
You seem to be talking about an account that has worked at Work and having new computer at home.
As I mentioned the Priority thing you have not said that it has coincided with the new computer logging in (this will kick the work Computer out of Google whether you are logged in on the Web Mail page or in iChat)
IN addition to that iChat stays partially logged in for Off Line IMs
This is done in the background by a support app called iChatAgent
If your Computer is ON but ichat is not started people can still send you Messages.
Instead of saving these on the server until you login iChat will start up.
Depending if the home Mac is effecting the Work Login it may be holding sway over your Login.
Using your girlfriend's login may have booted her Off Line where she normally uses the name/login.
The AIM Side can be specifically set to allow Multiple Logins and therefore NOT allow them. If this happens you get a warning and messages to do something about it.
You do not get these in any Jabber or Google Login as the Priority setting is supposed to take care of it.
If the Login works at the Web Mail Login and on one computer then the .plist on the work computer is the most likely issue.
There is a small chance that a Corrupt Buddy Pic (Home Folder/Library/Caches/com.apple.iChat/Pictures) may be the cause.
Set this folder to icon view and also use the Finder's View Menu > Show View Options and select icon view.
This should show all pics as their icon.
Check that all display properly.
At this point I would try a COMBO version update install of the last Update you did over what you have.
This often corrects hard to trace things
The 10.5.8 COMBO is here
11:28 PM Monday; June 20, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
 Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

HP Pavilion DV6750er Laptop no longer go into passive cooling

Similar Messages

Maybe you are looking for