HP Pavilion DV7 1120eo doesn't boot (Error Code 1 / CPU)

Hi,
I have a DV7 that doesn't want to boot.
When I try to boot it up, the screen just stays black and the caps lock indicator blinks one time between each "pause", which should be an error code for broken CPU(?!).
I asked the HP Support team on Twitter how reliable the error codes are, and according to them they should be reliable.
So I repleaced the CPU with another one, but still the error code shows when I try to boot.
I'm just wondering if you may know what could be wrong? Could the CPU socket itself be broken?
I found a long hair laying in between the CPU and CPU socket, but I reckon that it can't be the problem, or else something would've gone wrong like 3 years ago - since it must have been there since the computer was manufactured.
Anyway, I hope I can get some clarity or advice on things to try out.
Best Regards
Alexander

Baking in the oven can work but it is a crude, temporary fix. Unless you have access to high tech diagnostic and repair tools, a bad motherboard is a bad motherboard and is a "replace only" item. There are services on the internet where shops with the tools will fix your motherboard and the cost is very reasonable if you can remove the motherboard yourself and just ship that, instead of the whole computer. We are talking in the range of $60US. Even if you have to send the board to the US, the cost is very competitive with a replacement board.  Here is a replacement board on eBay that ships worldwide from China:
http://www.ebay.com/itm/HP-Pavilion-DV6-DV6-1000-D​V7-DV7-1000-Series-laptop-AMD-Motherboard-509404-0​...
This repair service would be $108 with shipping:
http://www.ebay.com/itm/Motherboard-Repair-Service​s-HP-Pavilion-DV7-1000-486542-001-506124-001-/3008​...

Similar Messages

  • HP Pavilion dv7-4165dx SMART Hard Disk Error Hard Disk 1 (301)

    My HP Pavilion dv7-4165dx when first turned, the screen reads "SMART Hard Disk Error" "Hard Disk 1 (301)

    blackeneds
    Your System supported HDD to 1 TB Page 2 , 55 and 107http://h10032.www1.hp.com/ctg/Manual/c02657339.pdf
    Sata III works
    Say thanks by clicking the "Kudos! Star" which is on the left.
    Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue.

  • HP Pavilion dv7-4065dx will not boot with continual blinking capslock

    Hi,I have a HP Pavilion dv7-4065dx laptop with Windows 7 64 bit that will not boot up or go to the Bios screen.  When the laptop is turned on, you hear the system fan start, power button light comes on, and the caps lock button starts to continually blink once every three to four seconds.  The HDD activity light is also on but is solid red with no blinking.  No changes have been made to the laptop and it was working perfectly fine just a few hours earlier.  I have attempted the hard reset of the computer and reseating of the memory cards, but the laptop still would not boot.  Any help on figuring out what is wrong with the computer would be greatly appreciated.  Thanks. HP Pavilion dv7-4065dxProduct # WQ861UA#ABA

    hp dv7-4065dx caplock key continous blinking the same problem i also faced but do the below step which solved your problem Bios corruption  power on your laptop block the fan air through cotton or any cloths 10-15 minutes (after heating) then power off and remove the cloths and power on it should be display visit hp driver and download the latest bios & bios tool first install bios tool and select usb to store connect a pendrive for  location after installed then install your latest bios  after sometime it will auto reboot and install the latest bios  we sure while updating bios power adpator must be connect   problem solved........

  • Pavilion dv7-3165dx will not boot up

    This pavilion dv7-3165dx has worked flawlessly for 8 years. Now when I turn it on, the lights come on and the fan runs, but nothing loads up, not Windows, not BIOS, nothing. The screen stays blank. I have cycled the power several times with the same result. I checked the BIOS battery, and it is good: 3.25 volts.

    Hi there @Terry49,
    Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
    I understand that your notebook is no longer starting up properly, and I am happy to help with this.
    I would start out with this process, and see if there is any change. It is possible that just the hard reset is required.
    Computer Does not Start (Windows 7, Vista, XP)
    Also check your power adapter, and if you have another one, try it out, and also try a different wall outlet.
    I hope this helps.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • HP Pavilion Elite e9240f won't boot -- beep codes

    When I try to boot my hp desktop I am getting beep codes.  As best I can tell it's one long then 8 short.
    I have not replaced or changed any hardware or software.
    I have used compressed air to blow out all the fans I saw.
    It's been an intermittent error that I thought was related to heat.  I'd turn it off, let it sit for the night, and it would work in the morning.
    The last time it worked, I was wondering about a virus so I ran an avast full system scan.  It found one file in the 1 tb drive (sorry, don't remember name, just that it was a .tmp file) and it said to move it to chest I believe so I did that.  It then suggested doing a boot scan so it restarted and has since given the same beep code errors.
    I have unattached the cables for the cd and dvd drives, as well as the hard drive, and I still get the error.  I've removed the video card and still get the error.  I've held the power button down so that the led light inside the computer shuts down.  I seem to get fans to run but nothing else.
    I made a system repair disk from another Windows 7 Professional (which I think this one is) and that won't work (I can't seem to boot into that) because it doesn't seem to get to an HP screen to boot into the cd.
    Thoughts?
    Thank you

    Hi,
    This is the HP troubleshooting link for POST error codes.
    You could try reseating memory modules or removing one at a time and testing for a successful POST.
    Jaco
    Errare humanum est.

  • Windows boot error code 0xC00000e9

    When booting from windows 7 Installation DVD source in my Windows server 2008 R2 there is an error pertained-Error code 0x00000e9-File: \Boot\BCD (An unexpected I/O error has occured).What is this error? What is the remedy for this?MumthazMuhsin

    Hi,
    Did you want to install Windows 7 on your Windows server 2008R2?
    The error message: An unexpected I/O error has occurred. Status: (0Xc00000e9)
    is a hardware error pertaining to your system’s BIOS.  Basically it is telling you that the computer is not able to reliably communicate with the hard drive.
    I suggest to update BIOS to the latest version, and try to rebuilt BCD follow these steps in this thread:
    http://social.technet.microsoft.com/Forums/en-US/winservergen/thread/0e6a7b6a-70de-41af-b2c8-5f8f3c86cef7/
    Hope that helps.
    Regards,
    Leo  
    Huang
    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

  • Z77A-GD80 Boot Error Code 55

    Okay, let me start with my setup.
    CPU: i5 3570K
    MOBO: Z77A-GD80
    RAM: 4x16GB 2133 Patriot Viper 3
    PSU: Corsair AX850
    GPU: EVGA GTX 690
    My rig is able to boot when more than 2 DIMM slots are used. It will post Error Code 55 and just try to reboot repeatedly with no luck. I tried the following method that worked on my old ASRock Extreme6.
    1. Turn system off
    2. Take all RAM out except A1
    3. Clear CMOS
    4. Set XPM Profile1
    5. Repeat steps 1-4 adding another stick of RAM until all 4 are installed.
    To no luck, this method wasn't successful with the GD80.
    Any suggestions?

    Quote from: xmad on 07-September-12, 04:36:35
    Do you have bios 1.0 installed?
    1.1 was terrible for allot of us with the z77a-gd80.
    Try: https://forum-en.msi.com/index.php?topic=160715.0
    Use the forums flash tool.
    >>Use the MSI HQ Forum USB flasher<<
    Then try with xmp disabled afer a full cmos clear.
    Ps. Did you try each stick individually and each dimm by itself as well? (Check for bad memory / dimm/pathway etc)
    I will flash BIOS to 1.0 this afternoon.
    Yes, I tried each DIMM slot and all memory sticks work. I changed MOBOs from ASRock Extreme6 to the GD-80.
    Thanks for the suggestion, I post results tonight.

  • HP Pavilion DV7; System will not boot; Memory Test Failed using Advanced System Diagnostic​s

    Not sure exactly how, but I managed to contracted several variants of the nasty Rovnix virus and now my system will not even boot into Safe Mode after trying to restore to several different restore points.  Enabled bootlogging, but not sure how to retrieve the log.
    Currently am able to get into HP Advanced Diagnostics and began Start-Up Test.  Test failed on Memory Module:
    Failure ID: Q0AE6C-5LS79T-MFH15G-406N03
    Any next steps or directional assistance would be greatly appreciated.  Thank you in advance!

    Hello @GarrettBishop,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how your notebook computer has failed a memory test in the advanced system, and I would be happy to assist you in this matter!
    Since the Failure ID has come up with Q0AE6C-5LS79T-MFH15G-406N03, I recommend contacting our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assis​t.html
    I hope this helps!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Re: MSI 970A Boot Error Code 99

    Hello, wow shooffnyc I&#39;m having almost the same issue and with a very similar build.
    At startup I get POST error 99 if I have anything other than my mouse and keyboard connected via USB so my webcam and USB stick all need to be unplugged then after res...

    Hi guys, i upgrade my GP60 2QF to win 10. All works good but FN+F8 (WiFi) and FN+F9(Bluetooth) doesn´t work. Other FN keys working right. I reinstall SCM but doesn´t help. Can anyone help me ? ... sorry for my bad english :D

  • ITunes doesn' recognize iPhone; Error Code -18

    Has anyone experienced this problem? Suddenly iTunes doesn't recognize my iPhone. it shows up in iTunes simply as "apple iphone" and I get an error message telling me I have to reset to factory setting (wont let me do anything else and does not show my music/video's, but DOES open iPhoto). when I try to reset to factory settings, I get a second error message telling me can't reset to factory settings due to unknown error (-18).
    I have quit and reopened iTunes. I have restarted computer. I have restarted iPhone. I have the latest version of iTunes and the latest version of iPhone OS. Anyone have any ideas?
    Thanks much!

    Having the exact same problem with my iPhone 4S.
    This started happening right after upgrading iTunes to 11.1.5 - never encountered this issue before.
    Tried doing the same thing you mentioned above with no luck at all.

  • Z87-G45 Gaming - Boot error code A2 (stalled)

    Hey folks,
    I just purchased this board with an i5-4670k
    I have a weird issue with the boot process.  It doesn't occur at bios default values, only when I change them.
    Here is the steps I do prior to get this stalled on BIOS load screen
    1- I change the OC settings to get to either 4.2 or 4.4GHZ (1.29v for CPU 4.4ghz and 2v for input)
    2- hit F10, save and restart
    3- Boot normaly into windows.
    4- Launch AIDA64 to stress test the system for 8h.  Yes I did the 8 hours at first.  It successfully passed the stress test.
    5- I browsed a little bit.
    6- I played battlefiled
    No issue so far.
    7- I shutdown the computer.
    8- I then restarted it, and BOOOOMM.  It stalls on the black screen, prior to the Dragon screen, with a A2 code in the lower right corner.
    So I know the the OC is fine, since the stress test is OK for that long.  I tried it several time, but only stressed it for 30min, then reboot and BOOMMM again.  :/
    So can someone, from MSI, help me?
    Thx
    System info:
    MB: Z87-G45 Gaming
    BIOS: v1.6 (Which I falshed from the BIOS menu)
    CPU: i5-4670k
    RAM: Corsair 8GB (1866MHz)
    DISK: Kingston SSD 120GB, WDC 1.5TB SATA3, LG BD/DVD

    Hey!
    I decided to chip in since I have almost the same issue.
    My PC boots to Windows and runs just fine apart from the 2second A2 debug code delay. Been playing games like BF4 for a good amount of time etc.
    I just seem to be getting that same A2 debug code whenever I boot, seems to be the WD Caviar Red drive I just bought a week ago, already tried a few different sata and power cables, which dont help the case. When I unplug it the boot happens normally without any debug codes. Thing is the HDD seems to be working just fine, tested it with HD Tune Pro and CrystalDiskInfo. Also im not certain, but pretty sure that the A2 debug code only started happening after I installed a GTX 770 (day after the WD 1TB Caviar Red drive). Then again that doesnt make much sense? Since then it would most likely be an issue with the PSU, but seeing how I can play BF4 on high settings for 2hours straight it most definately isnt I think. My problem doesnt have anything to do with overclocking though, since I run everything on default.
    Any ideas? And again, sorry for chipping in your thread. Just saw the same debug code problem and thought I shouldnt do a new one.
    Specs:
    i5 4670K
    MSI z87 G45-Gaming
    MSI GTX 770 TF OC 2GB (old gfx card HD7870)
    8gb G-Skill Ripjaws 1333mhz
    2x 120gb SSD (Kingston and PNY)
    1x WD Caviar Red 1TB HDD

  • Creative Cloud Desktop App Update 1.7.0.413 doesn't install, error code 89

    I am running CS6 on Windows 7 x64. The Creative Cloud updater is insisting that I run it's update to version 1.7.0.413, but it fails each time. I had a look at the file ...Temp\AdobeDownload\LBS.log, and found the message "ACC installation failed with status: 89" (full section of the log is below). I also had a look at Troubleshoot install issues with log files | CC but did not see anything there. The updater gives me only the two choices "Install Now" or "Quit", so I am dead in the water.
    Any thoughts?
    Thanks, Bruce
    07/13/14 12:45:46:360 | [INFO] |  | ACC | LBS | ETS |  |  | 3376 | Event Guid generated is: '8a1e5a0a-be2c-4461-a5a9-6542c7c89652'
    07/13/14 12:45:46:360 | [ERROR] |  | ACC | LBS | InstallThreadProc |  |  | 3376 | ACC installation failed with status: 89
    07/13/14 12:45:46:361 | [ERROR] |  | ACC | LBS | IPCWrapper |  |  | 3376 | Error sending IPC packet to ACC: -4
    07/13/14 12:45:46:366 | [INFO] |  | ACC | LBS | ETS |  |  | 11576 | Event with guid '8a1e5a0a-be2c-4461-a5a9-6542c7c89652' is being sent
    07/13/14 12:45:46:368 | [INFO] |  | ACC | LBS | ETS |  |  | 11484 | Waiting for the async thread to get the task completed
    07/13/14 12:45:46:371 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | GetIEProxyInfo - No default proxy present on the user machine
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11088 | HTTP Request Status code 200.
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | The http request returned HTTP_Status:0 HttpCommunicator error:0
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ETS |  |  | 11576 | Async thread is completed. Now exiting from function.
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ApplicationFacade |  |  | 11484 | ACC installation end with exit code: 89
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ApplicationFacade |  |  | 11484 | ****************Closing LBS workflow*******************
    07/13/14 12:45:46:502 | [INFO] |  | ACC | LBS | LBSUtils |  |  | 8172 | Elevated LBS exited with return value: 89
    07/13/14 12:45:46:502 | [INFO] |  | ACC | LBS | ApplicationFacade |  |  | 8172 | ****************Closing LBS workflow*******************

    This is actually the full text of the LBS workflow (the beginning was omitted from the original post).
    07/13/14 12:42:40:107 | [INFO] |  | ACC | LBS | ApplicationFacade |  |  | 11484 | ****************Starting LBS workflow*******************
    07/13/14 12:42:40:117 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | LBS launched in SELF-UPDATE mode
    07/13/14 12:42:40:117 | [INFO] |  | ACC | LBS | IPCWrapper |  |  | 11484 | Initializing Communication Channel with ACC with pipename: {F6EB1303-80E4-4C66-A7C5-00596AB0F809}
    07/13/14 12:42:40:342 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | ACCC System requirements check passed
    07/13/14 12:42:42:002 | [INFO] |  | ACC | LBS | ProductInfo |  |  | 11484 | Product Sap Code not specified in the product information file
    07/13/14 12:42:42:002 | [INFO] |  | ACC | LBS | ProductInfo |  |  | 11484 | Applet Version not specified in the product information file
    07/13/14 12:42:42:002 | [INFO] |  | ACC | LBS | ProductInfo |  |  | 11484 | Applet ID not specified in the product information file
    07/13/14 12:42:42:002 | [INFO] |  | ACC | LBS | ProductInfo |  |  | 11484 | Product locale not specified in the product information file
    07/13/14 12:42:42:002 | [INFO] |  | ACC | LBS | ProductInfo |  |  | 11484 | Product name not specified in the product information file
    07/13/14 12:42:42:003 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | Bootstrap LBS is successful
    07/13/14 12:42:42:013 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | Bootstrapper Lock acquired
    07/13/14 12:42:42:023 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | LBS Lock acquired
    07/13/14 12:42:45:466 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | PDM completed with error in downloading PIM with error 0
    07/13/14 12:42:45:568 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | Successfully downloaded pim at path C:\Users\Bruce\AppData\Local\Temp\{B61FBBED-59CE-46F5-9434-F97602EF8723}\CCLBS\PDIM\Adobe PIM.dll
    07/13/14 12:42:45:594 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | pim validation successful
    07/13/14 12:42:45:654 | [INFO] |  | ACC | LBS | WorkflowManager |  |  | 11484 | PIM loading is successful
    07/13/14 12:42:45:664 | [INFO] |  | ACC | LBS | InstallThreadProc |  |  | 3376 | Installing latest Adobe Creative Cloud
    07/13/14 12:42:45:722 | [INFO] |  | ACC | LBS | ETS |  |  | 3376 | Event Guid generated is: 'b1395ac2-b690-4c0c-b413-d463c2151798'
    07/13/14 12:42:45:731 | [INFO] |  | ACC | LBS | ETS |  |  | 11576 | Event with guid 'b1395ac2-b690-4c0c-b413-d463c2151798' is being sent
    07/13/14 12:42:45:735 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | GetIEProxyInfo - No default proxy present on the user machine
    07/13/14 12:42:45:836 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 10296 | HTTP Request Status code 200.
    07/13/14 12:42:45:836 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | The http request returned HTTP_Status:0 HttpCommunicator error:0
    07/13/14 12:43:43:832 | [INFO] |  | ACC | LBS | ETS |  |  | 3376 | Event Guid generated is: '5ea7a9c4-bc9a-4636-b173-fab8bc23bf35'
    07/13/14 12:43:43:839 | [INFO] |  | ACC | LBS | ETS |  |  | 11576 | Event with guid '5ea7a9c4-bc9a-4636-b173-fab8bc23bf35' is being sent
    07/13/14 12:43:43:844 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | GetIEProxyInfo - No default proxy present on the user machine
    07/13/14 12:43:43:889 | [INFO] |  | ACC | LBS | ETS |  |  | 3376 | Event Guid generated is: '24719e9d-510a-4795-a4de-77eee3b02aca'
    07/13/14 12:43:43:944 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 10296 | HTTP Request Status code 200.
    07/13/14 12:43:43:945 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | The http request returned HTTP_Status:0 HttpCommunicator error:0
    07/13/14 12:43:43:945 | [INFO] |  | ACC | LBS | ETS |  |  | 11576 | Event with guid '24719e9d-510a-4795-a4de-77eee3b02aca' is being sent
    07/13/14 12:43:43:951 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | GetIEProxyInfo - No default proxy present on the user machine
    07/13/14 12:43:44:045 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 10296 | HTTP Request Status code 200.
    07/13/14 12:43:44:045 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | The http request returned HTTP_Status:0 HttpCommunicator error:0
    07/13/14 12:43:46:123 | [INFO] |  | ACC | LBS | IPCWrapper |  |  | 3376 | Sent IPC packet to quit ACC with data: <message><name>QUIT</name></message>
    07/13/14 12:45:46:360 | [INFO] |  | ACC | LBS | ETS |  |  | 3376 | Event Guid generated is: '8a1e5a0a-be2c-4461-a5a9-6542c7c89652'
    07/13/14 12:45:46:360 | [ERROR] |  | ACC | LBS | InstallThreadProc |  |  | 3376 | ACC installation failed with status: 89
    07/13/14 12:45:46:361 | [ERROR] |  | ACC | LBS | IPCWrapper |  |  | 3376 | Error sending IPC packet to ACC: -4
    07/13/14 12:45:46:366 | [INFO] |  | ACC | LBS | ETS |  |  | 11576 | Event with guid '8a1e5a0a-be2c-4461-a5a9-6542c7c89652' is being sent
    07/13/14 12:45:46:368 | [INFO] |  | ACC | LBS | ETS |  |  | 11484 | Waiting for the async thread to get the task completed
    07/13/14 12:45:46:371 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | GetIEProxyInfo - No default proxy present on the user machine
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11088 | HTTP Request Status code 200.
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ETS |  | HTTPConnector | 11576 | The http request returned HTTP_Status:0 HttpCommunicator error:0
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ETS |  |  | 11576 | Async thread is completed. Now exiting from function.
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ApplicationFacade |  |  | 11484 | ACC installation end with exit code: 89
    07/13/14 12:45:46:494 | [INFO] |  | ACC | LBS | ApplicationFacade |  |  | 11484 | ****************Closing LBS workflow*******************
    07/13/14 12:45:46:502 | [INFO] |  | ACC | LBS | LBSUtils |  |  | 8172 | Elevated LBS exited with return value: 89
    07/13/14 12:45:46:502 | [INFO] |  | ACC | LBS | ApplicationFacade |  |  | 8172 | ****************Closing LBS workflow*******************

  • 6910p wont boot / error code?

    HP compaq 6910P displays when powered on -lBe-$-lBe$_ . A backwards accent is over the small e and the dash and small l are connected when powered on. Checked the HD and memory in the bios and all is AOK. Can't boot up, no drive letter displayed. Running windows vista and don't have a boot disk. Does anybody know what this means?

    Hi,
    You can get a VISTA repair and recovery disk here.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • KM3M-V wont boot error code 1 long beep two short

    As above but after the 1 long beep and two short beeps it gives off 2 deeper tone beeps! Is it the onboard graphics card thats at fault? if so I'll need to get the m'board replaced, have tried different ddr memory and no difference, processor is an Athlon 2400+ XP
    Cheers

    Quote from: vanaaken on 22-March-05, 00:34:53
    Its a PC I've built for a friend, no bios or hardware update had been performed all he did was come in one night and turned it on, and it did that, it has 512Mb DDR 2700, Athlon 2400+ XP and uses everything onboard eg sound and graphics, no it doesn't have a d bracket unfortunatly! Have tried disconnecting all the drives and even swapping the memory and it still gives the same code.
    how long has your friend had the system? did he do anything to it before it started doing this?
    you say you swapped the memory, does the system have two sticks, if so try just one on its own. if you only have one stick in it, then try some memory out of another machine. do you have an AGP card you could try? maybe some nasty dust is settled inside AGP slot, try blowing out with air duster

  • Z77A-gd65A boot error code 15 rebthing i removed all except cpu and ram and oot

    my pc used to work fine yesterday i shut it down and started it today and it kept cycling rebooting at code 15 on debug i changed to bios B and the same thing did clear cmos both ways even removed  the battery the same also removed all except cpu and ram but still the same result please help !

      I have no idea how you possibly could corrupt bios A if you weren't running Live Update or manually attempted to flash. if bios is really corrupted follow: >>Flashing a Corrupted bios when the alternate bios still works<<

Maybe you are looking for