HP Pavilion DV7; System will not boot; Memory Test Failed using Advanced System Diagnostic​s

Not sure exactly how, but I managed to contracted several variants of the nasty Rovnix virus and now my system will not even boot into Safe Mode after trying to restore to several different restore points.  Enabled bootlogging, but not sure how to retrieve the log.
Currently am able to get into HP Advanced Diagnostics and began Start-Up Test.  Test failed on Memory Module:
Failure ID: Q0AE6C-5LS79T-MFH15G-406N03
Any next steps or directional assistance would be greatly appreciated.  Thank you in advance!

Hello @GarrettBishop,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook computer has failed a memory test in the advanced system, and I would be happy to assist you in this matter!
Since the Failure ID has come up with Q0AE6C-5LS79T-MFH15G-406N03, I recommend contacting our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assis​t.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Similar Messages

  • HP Pavilion dv7-4065dx will not boot with continual blinking capslock

    Hi,I have a HP Pavilion dv7-4065dx laptop with Windows 7 64 bit that will not boot up or go to the Bios screen.  When the laptop is turned on, you hear the system fan start, power button light comes on, and the caps lock button starts to continually blink once every three to four seconds.  The HDD activity light is also on but is solid red with no blinking.  No changes have been made to the laptop and it was working perfectly fine just a few hours earlier.  I have attempted the hard reset of the computer and reseating of the memory cards, but the laptop still would not boot.  Any help on figuring out what is wrong with the computer would be greatly appreciated.  Thanks. HP Pavilion dv7-4065dxProduct # WQ861UA#ABA

    hp dv7-4065dx caplock key continous blinking the same problem i also faced but do the below step which solved your problem Bios corruption  power on your laptop block the fan air through cotton or any cloths 10-15 minutes (after heating) then power off and remove the cloths and power on it should be display visit hp driver and download the latest bios & bios tool first install bios tool and select usb to store connect a pendrive for  location after installed then install your latest bios  after sometime it will auto reboot and install the latest bios  we sure while updating bios power adpator must be connect   problem solved........

  • Pavilion dv7-3165dx will not boot up

    This pavilion dv7-3165dx has worked flawlessly for 8 years. Now when I turn it on, the lights come on and the fan runs, but nothing loads up, not Windows, not BIOS, nothing. The screen stays blank. I have cycled the power several times with the same result. I checked the BIOS battery, and it is good: 3.25 volts.

    Hi there @Terry49,
    Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
    I understand that your notebook is no longer starting up properly, and I am happy to help with this.
    I would start out with this process, and see if there is any change. It is possible that just the hard reset is required.
    Computer Does not Start (Windows 7, Vista, XP)
    Also check your power adapter, and if you have another one, try it out, and also try a different wall outlet.
    I hope this helps.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • How do I get recover disc for vista when system will not boot???? For Pavilion pc a6157c

    Pavilion pc a6157c   How do I get recover disc for vista when system will not boot????

    Read THIS HP Support Document concerning ordering recovery discs for your HP a6157c. Go to THIS HP webpage to order the "Vista Home Premium 32bit 73NAv3PrA1 + Supp 4 Recovery Kit" for your computer. If you are not looking to order the recovery discs or have some other issue with your computer, please provide detailed information concerning the problem.
    Frank
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

  • HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

    After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing. 
    I have tried a "hard reset" a number of times with no success. 
    When the battery is present the white LED flashes 3 times when the power button is pressed. 
    Please please help. 

    Hello Cuffy,
    Welcome to the HP Forums!
    I understand you notebook will not boot after a series of Windows updates.
    Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
    If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
    You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
    You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
    Hopefully this information helps!
    Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    The Great Deku Tree
    I work on behalf of HP.

  • My HP pavilion dv7-4069wm will not come on.

    Hello, my HP Pavilion DV7-4069wm will not come on. The screen is black and the caps lock blinks 1 time every 3 seconds. Is it my CPU or motherboard? What should I expect to pay for repair of either problem? I have very important docs & pics. Stored on this computer, can my memory be retrieved and put into another computer?

    Hi,
              Below lists the details of blink code. And you can visit the below site for more details
    Caps Lock/Num Lock LED Component Tested Error Condition
    LEDs blink 1 time
    CPU
    CPU not functional
    LEDs blink 2 times
    BIOS
    BIOS corruption failure
    LEDs blink 3 times
    Memory
    Module error not functional
    LEDs blink 4 times
    Graphics
    Graphics controller not functional
    LEDs blink 5 times
    System board
    General system board failure
    LEDs blink 6 times
    BIOS
    BIOS authentication failure
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01732674&tmp_task=solveCategory&cc=us&dlc=en&lc...
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443371&tmp_task=solveCategory&cc=us&dlc=en&lc...
    "I work for HP."
    Please click the "White Kudos" star to say thanks for helping.
    Please mark "Accept As Solution" if my help has solved your problem.

  • Windows 8 and Canvio Desk 3TB: System will not boot when external hdd is connected

    http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-e-g/HP-PAVILION-A6109N-amp-windows-8-System-w...
    Hi,
    just recently upgraded to Win Pro on my HP PAVILION A6109N.  I also bought a toshiba canvio desk 3TB.  What I notice is that if I reboot my pc with the extermnal HDD connected, my system will not boot.
    I have check my BIOS boot settings and the order of the boot.
    I have tried disabling USB Legacy Support in the BIOS
    I have reformatted the external HDD
    but still my desktop will not boot if the external HDD is connected....If I disconnect the external HDD...the system will boot up ....
    I am at a loss....*** scratching my head ***

    Update:  The only solution for me was to format the drive as ext3 and plug it into one of my Asus RT-N66U USB ports, as most routers don’t yet recognize 3TB drives as NTFS.  It’s not much help to people who don’t have a router with this capability, and it also slows transfer rates to ~12MB/s.
    Given the short length of the cable, your only other options are to have the 3TB Canvio sitting right next to you so you can unplug from a front USB port before each boot, or place it towards the rear of your desk and crawl under the desk to disconnect it from your PC prior to each boot. 
    It's a pity because Toshiba produce great internal HDD's, but my experience when it comes to external drives is they're simply junk.  I wish I had read the reviews before purchasing.

  • System will not boot up

    MB: KT6 Delta-LSR
    CPU: XP2500 Barton
    GFX: Asus V9520 Magic/T 128mb
    RAM: 1028 pc3200 ddr400 (2x512) Geil Branded
    HDD: Maxtor 40GB 2mb Buffer
    Put it all together formatted the HDD, installed windows, network was working perfectly. (on ASUS via600 board)
    Next day turn it on and nothing, zilch not even a flashing cursor top left of screen, dont even boot to DOS. screen is completely blank.
    Tested CPU, GFX, RAM and PSU in another base unit and they work fine, yet put them all together and nothing.
    1st I thought it was the mainboard so I sent the ASUS board back and ordered the KT6 Delta nice looking board. But still exactly the same problem.
    Lights on case are lit all fans are turning ect yet still the system will not boot up i dont even get a flashing cursor top right of my screen.
    There is no light with this mainboard for some reason.
    All components work when fitted to another mainboard in a different case.
    NB: one thing I have noticed is that there are two power sockets on this board,
    1. The usual 20 pin socket (which I am connected to)
    2. A 4 pin socket near to the CPU (whilst my PSU has a plug that will fit this sockect also, I am unsure as to connect instead of/as well as or leave unplugged.

    Like I have stated before, it is the compatibility issue related towards your chip fsb and your memory fsb. I know that not everyone has money to go buy another stick of memory, I don't. But maybe you could exchange from the place you bought and say that it was a mistake? The cheapest route without getting the fsb chip to match the fsb of the memory stick is to get PC2700 memory. Have you tried going for this yet? I'm sure that your motherboard may not be shot, my board didn't get shot after trying to the two different fsb. You have to understand, motherboards are picky when it comes to running the hardware. If there is a conflict, it won't run right, I could run at a lower fsb and get it to work fine, but it wasn't at it's full potential, and I wasn't going to waste my time trying to find the fsb that would work correctly. So, I just let my friend have the stick back. This is why I'm asking you to try a lower speed stick of memory, because I have experienced this. But so far you haven't even seemed to notice my replies, could you take a quick overview of what I have said? Sorry if I come off as rude, just I am taking the time to write these replies and really am trying to help from my knowledge base. I have experienced this type of problem of what you are talking about personally.
    Ok, so maybe I might not know it all, seeing that other people replying here have the same mb spec and chip fsb and memory like your trying to run, they might know more when it comes to that area for sure, just I didn't have luck trying to run a faster stick of memory compared to my chip, even though my board could run it, I couldn't get it to work, at all. I would just get a black screen, I thought I shot my GPU. Then I reset CMOS and the bios would flash, then when it would start pulling from harddrive, boom, black screen again. I had my friend tinker with my volt. to the right volts of the memory stick, still couldn't get nothing. This is why I am a little skeptical about you being able to run it at all in the long run. Hopefully you can find a way, maybe it is your manufacturer of your stick, but my conclusion is, if it isn't going to work with one, or two of same speed, try lowering it. Like I said, I tried it on this setup right now, and I didn't have to replace the chip or mobo, or gpu, so those should be fine.

  • System will not boot with Seagate 3Tb expansion drive plugged in.

    I have a  HP Pavilion HPE h8- 1214 Desktop ,  I recieved a Seagate 3TB expasion drive as a gift but when plugged in, the system will not boot. It turns on but thats it.  It never gets to the boot sequence. I have it plugged into the top 3.0 usb slot and have tried all of the other slots as well with no sucess. But if I leave it unplugged the system boots right up. I can then plug it in and it works fine. I have plugged it into my wifes HP All- In- One and it boots fine and works.  I have a WD 2TB drive that works fine as well on my system . I have searched Segates support for hours and all they say is to change the boot sequence. Have tried that, no go.  What they dont get is no matter what I do if that drive is plugged in it never gets as far as booting and reading the boot sequence. Please help. Thank you! 

    Hi NcBunky,
    Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
    I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
    When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
    Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
    System now boots with the external USB 3.0 drive attached.
    Jaco
    ****I am not an HP employee****
    Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
    +++++++++++++++++++++++++++++++++++++++++++++++++++++
    H8 1380t CTO, Intel i7 3820
    16 GB DDR3
    Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
    Envy Phoenix 810-150se, Intel i7 4820k
    16 GB DDR3
    Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
    HP 560z CTO AMD Phenom II X6 1090T
    16 GB DDR3.
    Radeon HD 6570
    Win 7 Home Premium upgraded to Win 7 Pro.
    HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
    12 GB DDR3
    Nvidia Graphics
    Win 8 Pro
    Errare humanum est.

  • The system will not boot

    Hello, I am trying to install windovws after the restart can not install Yosemite because can`t please format the hard disk.Please help because just yesterday bought macbooc

    FYI...the top partition is too full. You need free space. You will need to remove the bottom partition then make the top partition larger. Make sure you have 10% or more free space. If you use Parallels or VMware you don't have to partition your drive. If you use the vm software you can run Windows wihtout having to reboot into bootcamp each time you want to use it.
    See this link for help after you resize your top partition.
    https://www.apple.com/support/bootcamp/
    I forgot to ask...
    If the system will not boot, how are you seeing Disk Utility. Are you booted from the Recovery Drive? If yes, then you will need to erase the internal drive and reinstall Yosemite on the internal. When you erase, make it one partition. You can add a second partition later that's smaller.
    Note: you posted in the OS X 7 Lion instead of the Yosemite forum. In the future, asking on the correct forum gets the best answers.
    Parallels   http://www.parallels.com/
    VMware Fusion   http://www.vmware.com/products/fusion/

  • Operating reference system will not boot.

    hi! bought the iphone 4s in Italy and it does not work. Operating reference system will not boot. Change of firmware and restore did not help. How can I change it while in Russia. Can I send in the mail store??

    Hi NcBunky,
    Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
    I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
    When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
    Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
    System now boots with the external USB 3.0 drive attached.
    Jaco
    ****I am not an HP employee****
    Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
    +++++++++++++++++++++++++++++++++++++++++++++++++++++
    H8 1380t CTO, Intel i7 3820
    16 GB DDR3
    Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
    Envy Phoenix 810-150se, Intel i7 4820k
    16 GB DDR3
    Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
    HP 560z CTO AMD Phenom II X6 1090T
    16 GB DDR3.
    Radeon HD 6570
    Win 7 Home Premium upgraded to Win 7 Pro.
    HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
    12 GB DDR3
    Nvidia Graphics
    Win 8 Pro
    Errare humanum est.

  • Reset CMOS, system will not boot

    This is a long story but I will try to keep it short:
    I just bought a new 875P Neo-FISR and a 3.0 GHz Prescott, which from reading the other posts could have been a mistake. I installed the CPU, memory, and the video card and pressed the power button and received a "CMOS Data Wrong" error. So I tried to correct the problem but when I saved and exited then the system would not boot back up. So, I reset the CMOS via the jumper and tried again. After MANY attempts I change just the month in the date setting. And what do you know...it would not boot back up. The D-Bracket LEDs were: 1-flashing red/green, 2-flashing red/green, 3-red, and 4-red
    I must have read almost every post in this forum and tried many things such as:
    disconnecting all componets except for video, ram, and cpu
    the during boot to recover the BIOS
    removing mobo from case, maybe a short
    moving the memory to different slots
    moving the PSU to a different computer...it works
    disconnecting the PSU from the mobo and and removing the battery overnight. The first night I did not disconnecting the PSU from the mobo and I found that did nothing.
    Tryed everything that I could think of and some stuff that others thought of but nothing worked. However the last item...removing the battery...did change things some. Now nothing happens, and I mean nothing...no lights, no fans, no buzzing...nothing.
    Any ideas would be greatly appreciated. The only recourse I have left is to RMA the board.

    I tried one stick in all of the slots with and without the sound card. That did not work either.
    The voltage for my memory is 2.6 so that is what I tried. But if I can get it to boot up again I will try 2.7.
    Tks.

  • Pavilion g6 ID46 will not boot

    Product: Pavillion g6 ID46
    Serial # [edited by Moderator]
    Product # A6Z74UA#ABA
    OP sys: Windows 7 Home Prem OA
    My husband's Pavillion G6 will not boot. What happened: returned to the computer after being away for a while, shook the mouse to wake it up, and the screen "exploded into lots of colors and moving pixels." Screen went black, then a "would you like to start over in safe mode" screen popped up. He attempted a safe start, but it failed and gave him a Bios Application Error 501. He tried to restart the computer, but it hangs on the "Starting Windows" screen with the 4-color icon.
    I have:
    Removed the battery and tried to restart. No good.
    Took hard drive and and reseated it. Ditto.
    Tried to start in Safe Mode, before and after what follows below. "Loading files" always get stuck on Windows\System32\drivers\CLASSPNP.SYS
    Burned and ran a Repair disc. Took 4 hours and the program ran to the end when I was asked to restart. Computer hung on the "Starting Windows" screen. (I have let this screen run for over 5 hours without it changing.)
    Ran the System Repair program twice, same results.
    Ran Start Up Tests. Passed Primary Hard Disk Self Test, Hard Disk SMART Check, and System Memory Test (100% passed)
    Tried restoring BIOS using Windows + B and power with several attempts. Power button LED stays on, about 20 seconds later a small LED on 'caps lock' button begins flashing white Twice. Black screen and nothing happens after 5 minutes. Looked this up and 2 blinks is supposed to be BIOS corruption.
    Error Log lists these: Hard disk 1 Quick 303, Error 501, and Error 03F0.
    I do not have a great deal of computer smarts, so appreciate any help you can give, especially if the help is in simple and easy to follow terms.
    Mahalo in advance!
    This question was solved.
    View Solution.

    Hi @KikoKea ,
    Thank you for visiting the HP Support Forums. I needed to edit your post and remove the Serial Number present. In Accordance with our Rules of Participation:
    Protect privacy - yours and others'. Don't share anything about yourself that you would not want to see on a road-side billboard. Don't post contact or other personal information-your own or anyone else's-or any content that you receive in one-to-one communications without the author's consent. For example, don’t post your computer’s serial # or contact information publicly, and do not allow someone you don’t know to remotely take control of your computer.
    If you need people to contact you directly, either ask them to send you a private message or subscribe to the thread so you will be notified when there are replies. You may also click on your name anywhere in the forum and you will be taken to your profile page, where you can find a list of threads you have participated in.
    Sharing personal email addresses, telephone numbers, and last names is not allowed for your safety. If you have any questions feel free to send me a private message in reply.
    Thank you
    George
    I work for HP

  • New system will not boot up.

    I am in the process of building a new system and it will not boot to the post. The power gets to the cpu fan and case fan for about 5 seconds then shguts off. I have to clear cmos to get the same response. Please help, I have pulled everything from the case and tried to boot with just the cpu and memory. Same result.

    Quote
    Originally posted by FastEddie
    The Antec Bug involves their True Power line of psu's and involves a problem with the +5vsb.  It's caused quite a few problems with many different boards, from stability issues, to boot issues, to freezing in cmos setup issues.  Here's a couple links:
    Antec Problems with Neo 2 Platinum
    Antec RMA
    Read these through.
    Would be nice if you guys had different psu's to try.
    I recently had the "reboot loop during startup" problem with an Abit AI7 and the Antec  TruePower 480.  However, the problem didn't start to occur until several months after it was new.  After replacing the PS with a 430 amp Enermax the problem went away.

  • Black screen system will not boot

    My pavillion dv7 will not boot up. i can hear fan running but it will nit open. I have tried to go into recovery system but ti no avail. Black screen.

    Any flashing lights and beeping sounds?
    Sorry because of different timezone I might not be able to help/reply you right away.IF that happens I deeply apologize!
    **Click the White thumb if you like the answer.**
    **Please mark Accept As Solution if it solves your problem and only solves your problem, if you have any more questions please ask, this also helps others to solve related issues.**
    Feel yourself like home here, we are all happy to help, if you have an question reply or start a topic or pm me or an expert.

Maybe you are looking for