HP Pavilion dv8t-1100 Hard Drive Diagnostic failure - but runs fine?

I have a HP Pavilion dv8t-1100 CTO Entertainment Notebook PC (Windows 7 Professional 64-bit) that seems to run just fine. On a whim, I ran the pre-boot diagnostic check and received the following error code that the hard drive test had failed.
Q7NK1R-52M62E-XD002J-60WW03
Nothing in my PC's performance prompted me to run the diagnostic test, I simply ran it as a double check for the heck of it.
Is this something to be worried about? Of course an error code is always something to look into but since the PC seems to be running just fine is this a true error or simply a nuisance that should be ignored?
I can not remember making any signficant changes lately to the installed software and have made no changes to the hardware at all.
Any help would be greatly appreciated.
MJD

Hi,
I would resaet (not reset) the HDD or you may want to try this first:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443463&cc=ad&dlc=en&lc=en&jumpid=reg_r1002_in...
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

HP Hard Drive Diagnostic Failure Code VC7C3D-6NF7NV-MFPWWJ-60SJ03 -- What does it mean?

Hello, I recently used HP diagnostics (freshly updated) to run an extended diagnostic on the hard drive (Samsung/Seagate ST500LM012). The diagnostic failed within the first minute with the following failure code: Failure Code: VC7C3D-6NF7NV-MFPWWJ-60SJ03 What actions should this failure code be prompting? I did a search on the web for this rather elaborate failure code, but the search returned nothing. The system boots and runs with no problems, but the hard drive does have some bad blocks that have been recently picked up by "chkdsk /r" and added to the bad cluster file. A lot of device resets were being being logged to the Windows Event Log, issued by "amdsata" to the hard drive (/Device/Raid0), but since upgrading the amdsata driver to the most recent version from AMD's web site a day ago, the errors have stopped. So far as I can tell, everything else seems to be in order. Any help from someone at HP (who can hopefully look up the failure code) would be very much appreciated. Thanks, EAT

the meanings to those codes are not made public and only Apple certified technicians have access to them.

Wi-Fi adapter replacement for HP Pavilion dv8t-1100 CTO laptop

I have an HP Pavilion dv8t-1100 CTO Entertainment Notebook PC laptop. It seems as though the Wi-Fi is going out. After a while I the Wi-Fi connectivity stops functioning and I have to plug in an EitherNet cable to continue on-line. So how do I find out what the part number of the machine is, and where do I order a new one? Thanks.

Hi @MikeatHPformum
Welcome to the HP Support Forums!
In answer to your questions about the WLAN adapter and how to order a replacement, take a look at the attached serivce manual for the notebook family. HP Pavilion dv8 Entertainment PC - Maintenance and Service Guide
On page 51 of 148, or if you prefer page 4-17, the section on the WLAN adapter starts and shows the supported part numbers, as well as the replacement procedure.
And to order the parts check out this page.
HP Notebook PCs - Ordering HP Certified Replacement Parts
Let me know if you need any more help.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

HP Pavilion DV7 2206TX - DVD drive reads DVDs but not CD's

My HP Pavilion DV7 2206TX - DVD drive reads DVDs but not CD's.
When I insert a CD, the drive tries very hard to read the CD but gives up after about a minute.
I get no error message. I do not see the Auto play message.
Windows Explorer does not recognize the DVD drive.
When I insert a DVD, I get the Autoplay menu, Windows Explorer recognize the drive and the DVD. I can play the DVD using any number of Video players.
I would welcome advice relating this problem.

your HP Pavilion needs a new DVD driver. I ran into many problems such as this when troubleshooting computers in school.
A DVD drive should play CD at any time: While a CD driver will not play a DVD disc. Do not think there is a problem with sofware because it will only throw your troubleshooting skills out the window and it will confuse you.

I have a new Windows tablet computer with limited hard drive space, and cannot transfer my itunes library to the hard drive. Can I run t media from an external hard drive? If so, how do I transfer my files?

I have a new Windows tablet computer with limited hard drive space (32 GB), and cannot transfer my itunes library to the hard drive. Can I run itunes from an external hard drive? I have tried to follow some of the directions on this site, but am having no success. Thanks.

iTunes will run fine with the media on an external drive.
However, I suggest that a tablet computer with a tiny hard drive is not ideal as the primary computer for managing an iTunes library, even a small one. If you have another machine, perhaps a big, boxy, inexpensive old desktop with a decent amount of storage, that might be a better choice.
http://support.apple.com/kb/HT1364

I bought a new external hard drive for backups, but time machine won't do a full back up. I think it is remembering backing up onto previous external hard drives, which I don't own anymore. How do I do a new full backup?

I bought a new external hard drive for backups, but time machine won't do a full back up.
I think it is remembering backing up onto previous external hard drives, which I don't own anymore. How do I do a new full backup?
When I bought the new (used) iMac, I also bought an external hard drive for backups. It worked fine, but my husband stole it.
Then I bought a new external hard drive (Seagate) and it worked fine for three weeks, then died.
So I just got a new external hard drive, which was put together from an internal hard drive and a hard drive enclosure.
Time machine did the first backup today, and it should have taken 9 hours like it did on the previous first time full back up. Instead, it took 30 minutes. That can't be right. I want to start over and do a full backup to make sure everything gets onto my new external hard drive, but I can't figure out how to do that. Please help.

Triple-click anywhere in the line below to select it:
tmutil compare -E
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V).
The command will take at least a few minutes to run. Eventually some lines of output will appear below what you entered.
Each line that begins with a plus sign (“+”) represents a file that has been added to the source volume since the last snapshot was taken. These files have not been backed up yet.
Each line that begins with an exclamation point (“!”) represents a file that has changed on the source volume. These files have been backed up, but not in their present state.
Each line that begins with a minus sign (“-“) represents a file that has been removed from the source volume.
At the end of the output, you’ll get some lines like the following:
Added:
Removed:
Changed:
These lines show the total amount of data added, removed, or changed on the source(s) since the last snapshot.

I have a macbook pro. I had iphoto on it prior to my hard drive crashing. Hard drive was replaced but iphoto is no longer on. How do I get it back without paying for it?

I have a macbook pro. I had iphoto on it prior to my hard drive crashing. Hard drive was replaced but iphoto is no longer on. How do I get it back without paying for it?

Have you tried
http://support.apple.com/kb/HT4928

Can I install snow leopard on an external hard drive so I can run quicken 2006, and put snow leopard on my imac harddrive

Can I install snow leopard on an external hard drive in order to run my quicken 2006, and install lion on the hard drive of my imac?

You don't need to erase the drive and repartition from scratch. You may be able to add a second partition on the fly. The caveat here is that once you do that you cannot create a Windows partition using Boot Camp. Of course if you have no plans for Boot Camp then it isn't relevant.
To create a second partition on your existing startup volume:
To resize the drive do the following:
1. Open Disk Utility and select the drive entry (mfgr.'s ID and size) from the left side list.
2. Click on the Partition tab in the DU main window. You should see the graphical sizing window showing the existing partitions. A portion may appear as a blue rectangle representing the used space on a partition.
3. In the lower right corner of the sizing rectangle for each partition is a resizing gadget. Select it with the mouse and move the bottom of the rectangle upwards until you have reduced the existing partition enough to create the desired new volume's size. The space below the resized partition will appear gray. Click on the Apply button and wait until the process has completed. (Note: You can only make a partition smaller in order to create new free space.)
4. Click on the [+] button below the sizing window to add a new partition in the gray space you freed up. Give the new volume a name, if you wish, then click on the Apply button. Wait until the process has completed.
You should now have a new volume on the drive.
It would be wise to have a backup of your current system as resizing is not necessarily free of risk for data loss. Your drive must have sufficient contiguous free space for this process to work.
Now, you cannot add a new partition that exceeds the amount of contiguous free space at the end of the drive. Disk Utility will fail to add the partition if it cannot find sufficient contiguous free space. If that's the case then you will need to follow your state outline - backup, boot from clone, erase internal, repartition internal, restore backup to one of the partitions (or both in your case.)

Leopard cannot see hard drive on any Mac running Tiger.

Running Leopard 10.5.2 on a Mac Pro 3GHz 4-core w/6GB RAM. I cannot connect to any hard drive / root directory on any Mac on my network running Tiger (10.4.9, .10 or .11) or OS9. Yes I have an Avid Meridian in the edit suite runing OS 9.2.2. No laughing please...
I can connect to the User folder on any Mac running Tiger but not any hard drives on any Mac running Tiger from a Mac running Leopard. The hard drive cannot be accessed from a User folder even if an alias of the Tiger drive is placed in the ~/User/Public folder.
The reverse works as usual. Any Mac running Tiger can see any hard drive on any networked Mac including Macs running Leopard.
Has anyone else encountered this issue &/or found a workaround? I spent almost 2 hours with Apple Tech Support including a system specialist. They confirmed this behavior in Leopard connected to Tiger OS Macs. Hard drives can be seen between all Macs running Leopard. It was theorized by one of the Apple techs that the behavior was engineered to encourage upgrading all Macs to Leopard. BAD idea! I requested this be reported to Apple engineering.
Tiger can see any drive on the network back to OS7. Leopard cannot see previous OS version hard drives.
TIA for replies.

I suggest that you repeat the external boot process with your MBP. If it boots the MBP, the internal SATA cable probably is faulty and should be replaced.
Ciao.

Time Machine appears to be doing back-ups, but they do not appear on the external hard drive. The last one I can find is June 30. I did a utility scan of the hard drive disk and it is fine.

Time Machine appears to be doing back-ups, but they do not appear on the external hard drive. The last one I can find is June 30. I did a utility scan of the hard drive disk and it is fine. What do I do?

Click the Time Machine icon in the menu bar. The time of the last backup is shown in the drop down.

I reinstalled osx 10.8.2 from recovery disk, now verify disk says my hard drive is there but wont boot into it regardless which partition i select to boot into , everytime it boots me into the recovery, i need help!

Mb pro running like garbage with 10.8.2 tried a reinstall of osx from recovery utility now the utility says my hard drive is ok but wont boot into it keeps booting me back into recovery tried restart option to select disk tried using the select startup disk from recovery, gives a message asking if i really want to boot to it and in that message is the only rime it shows a question mark on the drive dont know what to do cant find similar issue

Your rushing and not making much sense.
Your machine was running like garbage, so you tried to reinstall 10.8---did you do this or not?
Disk Utility says your drive is ok, that's good.
But when you boot it keeps booting Recovery HD, so perhaps the firmware has made a mistake, it can forget.
You held the option key down to boot into Startup Manager, why didn't you select OS X for the boot volume?
When you get into OS X you change the Startup Disk in System Preferences, that should take care of the Flashing Question mark issue.
attemtping to ireinstall osx from recovery partition bar is full on install screen, but im now at -6hours remaining
So now your reinstalling OS X like you set out to do before, it does take some time as it has to download from Apple's servers.
If your Internet connection is slow and/or Wifi is slow then it will take awhile.
So you should have the Flashing Question Mark and Reinstall Only OS X covered.
You should be able to boot the machine, but your performance issues may be something else and still remain.
Why is my computer slow?
Step by Step to fix your Mac
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents#/?p er_page=50

HT201250 I want to use Time Machine to back up my pictures because my hard drive is full but I'm wondering if once I back up the pictures then delete them will time machine delete them off the back up too?

I want to use Time Machine to back up my pictures because my hard drive is full but I'm wondering if once I back up the pictures then delete them will time machine delete them off the back up too?

Evetually yes.
If your pictures have been in the same location (same folder, same subfolder, ...) for more than a week, then copies if them will remain in your TM backups until it fills up. They are then vulnerable to being deleted.
If they've been there for less than a week, TM could delete them as early as a month from now. If they've been there for only a few hours, chances are TM will delete them tomorrow.
This is why TM is not the best tool to use to archive data that you will be deleting from your main hard drive. Copy them to a dedicated external drive, or burn DVDs.

Hard drive packed up, but had Time Machine backup. I installed new sad and upgraded to Mountain Lion., but I can't find iPhoto library and photos or iTunes songs? Is there an answer to this? Graham

Hard drive packed up, but had Time Machine backup. I installed new ssd and upgraded to Mountain Lion, but I can't find iPhoto library and photos or iTunes songs? Is there an answer to this? A backup run did not install either photos or songs. Graham

Thanks so much but none of that helped. It was driving me crazy because it would back up another external drive. I just changed the name of the drive from iPhoto/iTunes Library to Media Libraries and IT WORKED!! I guess for some reason it didn't like the drive being called iPhoto or iTunes ???? I don't understand but I have tried so many solutions and exchanging things out but the name change did it????!!!
Thank you for your help and replying to this. Guess I made my own issue!

Is there a way for my macbook air (running Lion) to access an external hard drive on my Imac (running snow leopard) specifically for Iphoto and itunes?

Is there a way for my macbook air (running Lion 10.7.2) to access an external hard drive on my Imac (running snow leopard 10.6.8) specifically for Iphoto and itunes?

Yes. For those two applications specifically there is sharing. This presumes both computers are on and connected to the same network.
In iPhoto, enable sharing by (on the iMac) going to the iPhoto menu > Preferences > Sharing > check Share my photos. You can either share the entire library or only selected albums. Now on your MacBook Air, in iPhoto, go to the same preference pane and select Look for shared photos.
iTunes has something similar. In the iTunes menu > Preferences > Sharing > check Share my library on my local network. On the other computer, look in the left column for SHARED and select the iMac. You can now play that music on the MacBook Air.
There are other ways to share files but for those two applications this is the simplest way.
Best of luck.

How can I get all of my music off of my laptop and onto an external hard drive? I bought a new hard drive for it but it got turned into a Time Machine drive...

how can I get all of my music off of my laptop and onto an external hard drive? I bought a new hard drive for it but it got turned into a Time Machine drive... I want to have all of my music on the external hard drive, and NOT on my macbook pro. Thanks everyone

Hello lramospsych,
To move your iTunes media library to a different location, take a look at the article below to walk you through that process. Make sure that you have everything organized before you move everything over.
iTunes for Mac: Moving your iTunes Media folder
http://support.apple.com/kb/ht1449
Regards,
-Norm G.

HP Pavilion dv8t-1100 Hard Drive Diagnostic failure - but runs fine?

Similar Messages

Maybe you are looking for