HP Photosmart C6300 All in one series is not printing

I have replaced all cartridges, and gone through the troubleshooting program for Ink System Failure with no success.
I have the HP Photosmart 6300 printer. I need your help.
Loreen Brigham

Hello Loreen,
Can you try printing a testpage by pressing Setup»Tools»Printer Status Report. Please scan this page and add it to your post by clicking the insert/edit picture button, so that i can have a look at it.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Although I work for HP my posts and replies are my own
Please mark the post that solves your problem as "Accepted Solution"

Similar Messages

  • Hp photosmart 3210 all-in-one - some colors not printing even after changing cartridges.

     I recently had an issue while printing a document. the content was off colored and the error message said black was low. Changed the black cartridge and things just got worse from there. Still no black, cleaned the printheads, printed another test page and no longer had magenta or lt magenta. Replaced those as well. the only had yellow, magenta and lt. magenta.  yellow was low as well, so now every cartridge has been changes.Tried to print document again and it printed in magenta and lt magenta. never have seen black again and the self test diagnostic page is printing in purple. What should be black showed up as purple with lines and yellow is a rainbow of mustard, magentas and purples. no other colors show up. WHAT IS GOING ON? have tried several times to align the printer but it always fails. Have cleaned the printheads several time and just get a mish-mash of colors  (no black) and most of the time no writing. When I try to print in black only, I get nothing.
    What can I do? It worked just fine prior to ink going out.

    Did you get a resolution to your problem?  The same has occured for me - only printing blues/yellows and greens.  Was working fine until I replace the yellow cartridge and then it stopped printing reds.

  • Detection problem of my HP photosmart C5200 All-in-One series

    Hi,
    I have an HP photosmart C5200 All-in-One series and the printer will not detect that it is connected to the computer via USB cable. I checked all the USB slots in my computer and they are work, so the problem is with the printer. I tried installing and re-installing the printer to several computers and the installation goes well until the step that asks to connect the USB cable to the printer and computer for identification. However, printer seem not to recognize that it is connected. So, it gives me the option to proceed without the connection step and the installation is complete.
    If anyone had the same problem and solved, it would be greatly appreciated to have your help.
    Thank you.

    What operating system are you using ?
    You may try the HP Install Wizard to detect and resolve your issue.
    If I helped you at all it would be great if you clicked the blue kudos star!
    If I solved your post please mark it as solved to help others.
    I'm a printer tech with HP.

  • HP Photosmart e-All-In-O​ne C310a not printing black ink?

    HP Photosmart e-All-In-One C310a will not print black ink.  I've installed new genuine HP cartridges (original cartridges were also genuine HP).  I've run through all troubleshooting processes, test pages, clean heads, alignment procedures, and other suggested forum fixes such as "removing all cartridges, powering down, removing power cord, reinsert power cord, power up and reinstall cartrdges" which seemed to work for some other HP customer, but not me.  Any ideas?  Or am I fortunate enough to have a DUD?
    Please help....

    Hope you a having a great day,
    I am reaching out to probe if you still experience this issue. If you are, take the time to try this I might help,http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c02187415&cc=us&dlc=en&lc=en&product=4231205&tmp​...
    I will do my best to assist you. If you are not experiencing this issue any longer you may disregard this post, although I will appreciate if you can take I little bit of your time and let me know.
    Thanks
    RobertoR
    You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

  • Error message on my HP Photosmart C7280 All-in-One 'Wireless Radio not Working'

    error message on my HP Photosmart C7280 All-in-One  'Wireless Radio not Working' My broadband is BT Infinity with a very strong signal throughout the house and my operating system is Windows XP. My printer will not connect wirelessly to my network, what can I do with respect to the error message 'Wireless Radio not Working'

    Hello @GeoffH777 ,
    Perfect! You are very welcome, I am very happy to hear the reset helped!
    If you  have a quick moment, please scroll back to my last message here and click the "Accepted Solution" button, so others can find our thread if they happen to run into the same issue.
    Greatly appreciated, have a wonderful day!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • HP Deskjet all-in-one F4440 will not print

    My HP Deskjet all-in-one- F4440 will not print.  I have put in a new color and a new black cartridge.  It clanks loudly when it moves back and forth.  Finally it stops and then pulls plain paper through as though printing on it - does this two or three times.  then it pulls plain paper halfway through and stops.  I have to tug and carefully pull halfway paper back out towards front to remove.

    Hi there,
    Could you provide the community with a little more information to help narrow troubleshooting? Are there any error messages or flashing lights? What operating system are you using?
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • HP Photosmart 2610 All-in-One, Manual Two-Sided Printing, HP e-mail support Ticket no: 8028153835

    HP e-mail support, Ticket no: 8028153835 
    I purchased my HP Photosmart 2610 all-in-one printer in 2005. It was previously installed on a HP Laptop, Windows XP, and all the features worked.
    It is now on a PC running Windows Vista Ultimate 32. When I tried installing the printer software CD, it wouldn't load because of the Vista OS. I then loaded the HP Photosmart 2600 series full feature printer driver (Vista OS compatible) from the following HP website link:
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-47754-1&lc=en&dlc=en&cc=us&...
    Now I cannot get the Printing Preferences to allow Manually Duplexing (two-sided) printing. This option was available on the original printer software.
    I've tried the solutions on: HP Image Zone Help / Two-Sided Prints which indicate:  Click the Finishing tab / In the Document options area / select the Print on both sides check box (this box is not available).
    When I run the printer from the Control Panel as Administrator, the printer Properties / Device Settings show Manual Duplexing: Enabled.  When I go to the printer Properties / Advanced / Printing Defaults, neither the Finishing / Print On Both Sides check box is available nor will the Printing Shortcuts tabs allow the Print On Both Sides option to appear (only shows Print On Both Sides: Off).
    HP e-mail support told me to install this patch to correct the problem:
    http://h10025.www1.hp.com/ewfrf/wc/genericSoftwareDownloadIndex?softwareitem=mp-69848-1&cc=us&lc=en&...
    When I try installing the patch, it won't load because it wants the original CD software. So I'm back to my initial problem of trying to load the original printer software that won't load because the CD is for Windows XP OS. I am at an impasse between the Software CD that I have, and what is available on the HP website.
    What is your solution?
    This question was solved.
    View Solution.

    cschmidt41 wrote:
    I use Windows 7 Home Premium 64 bit and the Deskjet 6500 is not one of the choices. Any subs?
    Also, if it were, do you download the driver?
    The driver is supplied through Windows Update.  Go to the Devices and Printers folder, Add a Printer, then select Windows Update.  It will take a few minutes to update the list, then the Deskjet 6500 series will be a choice under HP (not Hewlett-Packard).
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • HP Photosmart Premium All-in-one c310a - How to print in black and white

    I want to print a color pdf file in b&w on my HP Photosmart Premium All-in-one c310a printer. When I go to "features" -> color options -> grayscale -> in the drop down box, there is only one choice - "high quality". There's no "black ink only" choice as I have seen in forums on similar printers.

    If you have the full feature drivers installed for this printer and there isn't a Black Ink Only option under Print in Grayscale, then this printer lacks the feature.  Typically the Black Ink Only options follows the drivers for some deskjets and most officejets, because of the office environments they are intended for.  Where as Photosmart printers are more aimed at printing photos. 
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.

  • I have an hp photosmart c7280 all-in-one series printer won't print. error message, system problem

    I have an HP Photosmart All-in-One C7280 series printer/fax/copier/scanner. I have been having issues with printing for the past few weeks. It is a wireless printer, with a jack into the wall (for fax) and it is plugged into a power source. I never used to have issues with it before, but recently, it won't print when I send a document to it to print. It will print its configuration pages, reports, etc if I select them from the Printer's menu but not when I send a doc to it to print. First it was saying it was offline, but I figured out how to override that by operating as an administrator and selecting "Use Printer Online" from the dropdown menu when I right clicked on the printer from the control panel. But now it says "Error: Printer failed to print document. System error".
    Noooo clue what to do now. This is the only color printer we have so we kind of need it to work. We bought this printer off the shelf at a office store (before I started working here) and so we don't have any designated technichians to work on it. I asked the guy who services our Image Runner Copier to look at it but he had no clue what was wrong with it. Hopefully someone can help?

    goestherain,
    I need to know what operating system you are using to helps narrow troubleshooting a bit, what OS are you running?
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • HP C6300 All-in-One Series

        I e-mailed HP Support on March 2, 2009 and received an automated e-mail that my inquiry had been received and then within a half hour or less I received a response from Samara who gave me a very clear and concise solution to my problem.  Being very new to Windows Vista, I had a few doubts that I could find any answers on my own, so the information provided in the e-mail was awesome and worked immediately.  I no longer have the problem, the All-In-One (C6300) works beautifully and I am extremely happy.  I love HP Products anyway and was so glad the Support was there and the fact that it was sent to me so quickly and efficiently impressed me very much.  I would not hesitate to recommend any product from HP and I have to say that they have one of the best Support Teams that I have ever dealt with - superior education and ability. I know now that if there is a problem, HP works with you to solve it and then does a follow-up to ensure it is still functioning.   Again, I was so ecstatic over this because I had become frustrated trying to figure it out by myself and to receive answers and THE solution was above and beyond on the part of HP.  Thank you so very much, and special thanks to Samara.

    PJ
    Thanks for your post which I frankly welcome!!!
    In the future it might be useful to share the details of the problem you had and the solution that was provided by HP email support. This way fellow users on the forum may benefit from the solution
    regards
    DaniW
    HP Forum Admin
    --Say "Thanks" by clicking the Kudos Star in the post that helped you.
    --Please mark the post that solves your problem as "Accepted Solution"

  • HP PhotoSmart PSC All-in-one 2410 driver not found

    HP claims to have and distributes a mac osx 10.4 driver for the 2410. I DL it, installed it but unfortunately the install process ends by looking for a 2410 on the network, not on my USB connection. After quitting the process, there is absolutely no driver available during Tiger "install a new printer". The GIMP and HPijs did installed drivers but none seems to be compatible with the 2410.
    Anyone found a Tiger compatible driver for this All-In-One HP 2410?

    Hello All,
    I have an HP PSC 2410 printer. I used the original install disk, which came with the printer and it works fine. All functions (ie. printing, scanning, faxing, etc.) work. I did have an issue of not being able to print after upgrading to Mac OS X 10.4.4. However, after manually uninstalling all the HP software (following instructions I located on HP's web site), reinstalling and then rebooting the computer, all functions of the 2410 work.
    I originally purchased the printer in 2003. So the software drivers are from that time frame. I did download the latest version of "HP Zone" and installed it as well. Again, all software works with Mac OS 10.4.4.
    Martin C. Meadows
    Power Mac Dual G5 2.3 GHz   Mac OS X (10.4.4)   1.5 GB RAM

  • Photo Smart 6510e ALL IN ONE SERIES. Only prints one page.

    photosmart 6510 with windows 7. Had problems so reinstalled and now only prints one page even when set to print all

    Hello bluebell21,
    Welcome to the HP Support Forums!
    I understand that you are having a printing issue with the Photosmart 6510 since you have re-installed the printer software.
    I would first suggest to run the Print and Scan Dr. This look into drivers, software and communication problems that could have caused this. Let me know the out come, what passes, fails, is fixed, etc.
    Cheers,
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • HP Photosmart C4380 All-in-one won't network print

    I ran the test, and my wireless radio is not working. i just wanted to know my options and where i stand.
    is it possible to fix or do i have to contact hp etc? I bought it sometime in 09, so it shud be within warranty if i can find it.
    thanks ,

    First I would reset the printer.  Turn it off, unplug power from the back of the printer (not the wall), wait 30 seconds, plug in, turn on.
    Now reset the Network Settings:
    1. Press the Wireless button on the front of the HP All-in-One.
    2. Press the button next to the icon on the display until Restore Network Defaults
    is highlighted, and then press the button next to OK.
    3. Confirm that you want to restore the network defaults.
    Run the Wireless Network Test again.
    If you registered your printer, HP will have the purchase and warranty date.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • HP Deskjet All in ONe L7650 will not print black only --

     Started doing this with previously working black cartridge, updated software--prints, but blank page comes out when set to black ink only; prints other colors. 
    Changed black print cartridge and still will not print black.  Diagnostic page prints other colors.
    Printhead health shows good for all colors.

    What brand of printer cartridges (not printhead) did you use the last time you changed them?  I don't know if it was because one or both of my printer cartrdiges went dry, but I put new cartridges in (not printhead) and it improved somewhat--I kept trying to clean the printheads but it seemed to never get resolved.
    I refuse to have to buy new printheads.  I tried several cycles of "align printheads" "clean printheads" and never got a decent print out, but I did get to the point of all the colors printing although magenta printhead makes printing errors and so I never know what I am going to get with color anymore.  
    It seems to be at its worst when printing in "draft" but in normal or best (with more ink coming through) it seems better--the higher ink volume seems to cover some of the problems with the printheads.
    So, I am justing using it "as is" and not replacing the printheads--because it is a waste and yes, could almost get a new printer for this cost.
    I wish I had never gotten this All in One and just stuck with the old 970 csi and the old UMAX scanner, which was a better scanner, but thought I would "save some space" by getting this since it scans legal, which I needed.
    Just keep trying to reseat the printheads (also trying to reclean them, which seems to make it worse) and keep printing out those "tools" alignment and cleaning procedures.  
    But no help from HP.

  • HP 7510 All-in-one - alignment failed - not printing centered on page

    HP 7510 All-in-one.  I am getting alignment failed message at initial set-up.    all colors print but text is not centered on the page.
    Help!

    Hi jillybeads99;
    Hope you are having a great day and sorry to hear that you are having this issue;
    Are  you still experiencing this issue?
    If you are, Try this uitility click here
    I will do my best to assist you.
    If you are not experiencing this issue any longer you may disregard this post, although I will deeply appreciate if you can take I little bit of your time and let me know.
    Hope it helps; 
    RobertoR
    You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

Maybe you are looking for