HP PSC 1410 All-In-One no longer prints

I have an HP 1410 all in one. I also recently updated to Mac OS X 10.5 Leopard. My printer no longer prints. It will show up in the print queue and the status will say printing but nothing will happen. After a few seconds it claims the printer is ready to print and stops any jobs in the queue. I have tried resetting the printer, tested all the connections, power cycled it both with the power switch and power cable, restarted my computer multiple times, I've tried updating the drivers (but I'll try again here in a minute), and I'm out of ideas. Any suggestions?

Am (attempting) to print direct from my MacBook - admittedly I did not install any printer drivers during the Leopard (clean) install and am a bit confused as to whether I'm now using the right one, but from what I can gather from the threads like this now littering this forum it wouldn't have made much of a difference. I had infact presumed my problem was just that - that I hadn't the right driver.
Like I hinted at previous; I can reconnect the HP to my old G4 running Tiger and print with no trouble whatsoever.
Trying to print from Leopard brings up the print dialog, and subsequent utility as it should but then nothing - as if the MacBook's not talking with the HP (though it happily recognises it as being there and what model it is etc.).
I have not yet attempted to print over the network, mainly because I couldn't succeed as is. Or tried to scan as it happens (I hardly ever use the built in scanner as I have a better one and the PSC is my backup - I scan a lot in my job).

Similar Messages

HP PSC 1410 All in One HANG INDEFINITELY with Remote Downlevel Document

Hi, after a few days of setting up my PSC 1410 All In One Printer, which is hooked up to a Compaq Presario V3000 running on Windows XP SP3 with AMD Turion 64x2 processor; and shared print to a Sony Vaio VGN FW33G, and a Mac Pro running on Snow Leopard OS X 10.6
Just yesterday, my printer was jammed with a "Remote Downlevel Document" which I can't remove after using these methods I've researched:
1. "Right Click and Cancel" x [indefinite] times
2. "Right Click and Refresh" x [indefinite] times
3. "Restart" x [indefinite] times
4. "Restart" with printer hooked on/off to the USB x [indefinite] times + [indefinite] combinations of whichever comes first
5. "Unhook USB and Click Start>Run "net stop spooler" and Rehook USB and Click Start>Run "net start spooler" x [indefinite] times
6. Did virus scan for suspicious virus using Anti Vir
7. And in between, combinations of the above x [indefinite] times
8. Search on the internet which obviously there's no real solution
Please help.
Regards,
Bobby

Am (attempting) to print direct from my MacBook - admittedly I did not install any printer drivers during the Leopard (clean) install and am a bit confused as to whether I'm now using the right one, but from what I can gather from the threads like this now littering this forum it wouldn't have made much of a difference. I had infact presumed my problem was just that - that I hadn't the right driver.
Like I hinted at previous; I can reconnect the HP to my old G4 running Tiger and print with no trouble whatsoever.
Trying to print from Leopard brings up the print dialog, and subsequent utility as it should but then nothing - as if the MacBook's not talking with the HP (though it happily recognises it as being there and what model it is etc.).
I have not yet attempted to print over the network, mainly because I couldn't succeed as is. Or tried to scan as it happens (I hardly ever use the built in scanner as I have a better one and the PSC is my backup - I scan a lot in my job).

HP PSC 1410 All In One, have driver problems...............................

I have an HP PSC 1410 All in one printer that I cannot print items from my computer on. When I try to print something from my computer my computer tells me that no driver for the printer is detcted but when I open "MY COMPUTER" and click Devices, it shows the printer listed as operational and that it is functioning properly.

I tried installing the driver and couldn't so I called HP and found out the printer is obsolete and no drivers are available........ they don't support that model anymore , So I'm screwed................

HP Psc 1410 all in one series Printing pink

Printer - HP Psc 1410 all in one series
Operating system - Microsoft windows Vista 32 bit
Ive installed the driver and the software but when i print colour the colour is pink. When I print in black and white it prints fine jsut colour is all pink.
Jamie

Please click here for a possible solution to your problem:
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&product=441115&docname=c00313147
Let me know if that helps.
Please click on KUDOS if you find my solution helpful.

Not able to install scanner part of 'HP PSC 1410 all-in-one'[SOLVED]

Despite trying instructions in the wiki, checking earlier reports of this problem on the forum and trying on reports from google, I am not able to install the scanner part of 'HP PSC 1410 all-in-one'. The command 'sane-find-scanner' finds it but 'scanimage -L' does not. Also xsane and simple-scan program do not find it. Any help will be appreciated.
(I also tried these entries in the udev sane rules:
ATTRS{idVendor}=="03f0", ATTRS{idProduct}=="4d11", MODE="0664", GROUP="scanner", ENV{libsane_matched}="yes"
"SUBSYSTEM=="usb_device", ATTRS{idVendor}=="03f0", ATTRS{idProduct}=="4d11", PROGRAM="/bin/sh -c 'K=%k; K=$${K#usbdev}; printf bus/usb/%%03i/%%03i $${K%%%%.*} $${K#*.}'", NAME="%c", MODE="0666", GROUP="scanner", ENV{libsane_matched}="yes"
but they do not work).
Some previous threads:
https://bbs.archlinux.org/viewtopic.php?id=107474
https://bbs.archlinux.org/viewtopic.php?id=65431
Not able to install sane-dev from AUR; 'makepkg -s' gives error:
==> WARNING: Cannot find the git binary required to determine latest git revision.
Last edited by rnarch (2012-03-28 05:05:09)

Git was not installed. So I installed it and ran 'makepkg -s' again. It ended with following error:
installing saned.conf in /etc/sane.d/saned.conf...
installing dll.conf in /etc/sane.d/dll.conf...
for dir in artec_eplus48u gt68xx snapscan epjitsu ; do \
/bin/sh ../mkinstalldirs /home/sane-dev/pkg/usr/share/sane/${dir} ; \
done
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/artec_eplus48u
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/gt68xx
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/snapscan
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/epjitsu
/bin/sh ../mkinstalldirs -m 775 -g uucp /home/sane-dev/pkg/var/lock/sane
Usage: mkinstalldirs [-h] [--help] [--version] [-m MODE] DIR ...
Create each directory DIR (with mode MODE, if specified), including all
leading file name components.
Report bugs to <[email protected]>.
make[4]: *** [install-lockpath] Error 1
make[4]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[3]: *** [install-data-am] Error 2
make[3]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[2]: *** [install-am] Error 2
make[2]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[1]: *** [install] Error 2
make[1]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make: *** [install-recursive] Error 1
==> ERROR: A failure occurred in build().
Aborting...
Please note the line: Report bugs to <[email protected]>. Is it a bug? Sane-dev was successfully installed by others, eg: https://bbs.archlinux.org/viewtopic.php?id=65431
Last edited by rnarch (2012-03-26 01:11:57)

HP PSC 1410 All in one Printer not installed

In windows 8 after complete and lastest installation of Driver of HP PSC 1410v All in one, in the Control Pannel, Device and Printer Tab only scanner icon is showing no any printer icon and no other HP Icon, so i can use scanner only of this model but not printer. After reading suggestions I install the windows 7 driver in windows 8 after solution of fatel error here is also only scanner is showing no facility for printing, please help me where I am wrong or whats solution fast plzzzzzz.

Hello Jai_pareek,
Welcome to the HP Support Forums! I see you would like to install your HP PSC 1410 to your computer running the Windows 8 Operating system. You tried downloading the Windows 7 driver but are now getting a fatal error. Please go ahead and start with the steps listed below:
1. Unplug the USB if using a direct connection.
2. Remove the HP PSC 1410 software from your computers Control Panel's Uninstall a program option.
3. Restart the computer.
4. Make sure ALL the PSC 1410 software is gone from the programs list as well as your HP folder listed under the All programs in your Start Menu.
5. Now go ahead and download the software and drivers for your PSC 1410 (DO NOT plug in USB until the software prompts you to):
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-110055-2&cc=us&dlc=en&lc=en...
6. Go ahead and print a test page.
7. If you are unable to print a test page, please run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
Please let me know if this was successful! I will watch for your reply.
Thank you,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

My HP psc 1210 all-in-one, suddenly stopped printing any text. it will print the graphics.

I believe I have tried everything. The HP psc 1210 series all-in-one refusses to print text. nor will it scan or copy. I have done all the troubeshooting that I can find. Still will not print from PC or copy. I think it will scan to the computer. Icon with gray circle around it, states it is offline, yet from the control panel, printer and faxes, shows it as being online and ready. What else can I do to remedy this problem? Thank you in advance.

There may be 2 separate issues here.
-For the offline portion, check this document out:
Printer is offline
-For just printing graphics, this would make me think that the Black cartridge is empty/low on ink/malfunctioning. Try printing a black and white picture. That would let you know if it is the cartridge or not.
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

Re: how do i install a hp psc 1410 all in one printer without the disk?

how to install?

lection wrote:
how to install?
Install what? If it is the PSC 1410 then what operating system? Do you have a 32 bit or 64 bit version? See my post here.
If a different printer model please start a new thread after reading this post and then provide some details. What printer model? What operating system? How is the printer connected - USB, wired LAN, Wireless LAN, bluetooth?
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP PSC 1410 All-In-One printer problem!

I have a PSC 1410 for a while now and I reinstalled Windows 7 recently and now the printer's not detected but I can scan documents. What could be the problem? It was working fine before I reinstalled Windows 7 and I've obviously installed the drivers.

Click here for troubleshooting tips for blinking lights on the PSC 1400 series printers.
Regards,
Bob Headrick, Microsoft MVP Printing/Imaging
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP PSC 1410 All in One

My HP Solution Center for this device, with no warning, failed to operate. I can click on the desktop icon or in "All Programs" and get no response. However the HP Photosmart Essential 3.5 , inttaslled at the same time, opens as usual. I can still print and copy with the device.
My operating system is Windows 7 professional. I can still scan with my alternate scanner HP Scanjet G4050, but I have to set it up each time as I only use it for bigger and more accurate (I think) scans. This is used with a desktop.
jw

Hello and welcome to the HP Forums!
I see you're experiencing software issues. I would like to help with that!
I would recommend performing a power reset on the printer. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would then suggest downloading and running the HP Print and Scan Doctor.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

PSC 1350 all-in-one not completing print jobs wirelessly with windows 7 64 bit

I have a acer 5542 running windows 7 (64bit), connected wirelessly to an Orange Livebox hub, to which my HP PSC 1350 printer is connected (via USB cable) therefore using the Livebox as a USB printer server. This configuration has worked very well for my 2 XP laptops for the past year or two. I set up the printer on the windows 7 laptop by connecting it directly, via the USB cable, letting windows install it, and download the latest drivers, (although HP say they have no specific 64bit drivers for this printer, but the drivers they have, and that windows downloaded, work fine!) then i changed the port to the livebox ip address.
All this worked fine (as on the xp machines), I printed out a spreadsheet, which worked fine untill it approached the end of the page, then just stopped. I troubleshot the printer which didnt return any sprcifics, Just that the print job had failed, and that it had rectified the problem, then the printer starts reprinting the same document, to the same point, (about 95% complete) and again stalls, and so the cycle continues. I have tried it with various different documents and photos, to the same ends. But if i connect the laptop directly to the printer, via USB, it completes the jobs fine
I have posted on microsoft answers forums, but the one answer i have recieved (re installing everything) did not solve the problem. Although i am not too savvy on computers, i kind of get the feeling it is a spooling issue. (not processing or holding onto the last part of a print file! But its only a feeling!)
any help would be very much appreciated

Hi there,
I understand you're looking for drivers for your PSC 1210 on Windows 7. I will certainly do my best to guide you in this issue.
At this time there are no HP drivers available for this printer for Windows 7. You can still use the printer with Windows 7, you will just have to use the drivers available within Windows 7. That document will walk you through what you need to do in order to get printing again, and will also show you how to scan with this Windows driver.
Hope this helps, have a great day!!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

HP 6110 All-in-one no longer prints...print jobs sit in queue

My printer worked fine last week and now I went to print somethign and it just sits in queue. I tried uninstalling/reinstalling the drivers, running the HP Diagnostic (which says everything seems fine) but nothing prints. Any ideas on how to get this working again? I also tried to print on my other laptop and that doesn't work either - so it's not an issue with this particular computer.
Any ideas would be greatly appreciated!

I have a similar problem but only with my vista pc. All print jobs sit in the queue, don't print. No problem printing on my mac. Please jhelp!

PSC 1510 All in One won't print black

Had printer for couple of years. Suddenly has decided doesn't want to print black. Tried everything. Have noticed other HP models on forum have same problem. One tag mentioned taking colour cartridge out and then it prints in black. Tried this but printer goes into fault mode as soon as I take colour cartridge out.
Any other ideas?

OK, if there is some black after manually cleaning the nozzles then the problem is the cartridges, not the printer. I would suggest running up to 3 cleaning cycles from the front panel. If this does not fix the problem then likely you need a new HP cartridge.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Hp psc 1110 all-in-one printer-copier-scanner

Recently I've been experiencing a problem with my printer (hp psc 1110 all in one): it will print fine, then suddenly it will not print even though the print job is listed in the que. If you turn the printer on and off, it will then "flash" in the system tray, but still won't print. I've tried restarting the print job, deleting the print job, etc. but nothing will make it print except to restart the computer. Then it repeats again where it will print a job or two then stop. I've checked connections, and unloading and reloading the drivers, but none of that helps. This is a great little printer -- I'm thinking it may have to do with the computer? It is connectly locally to a stationary, but we can also print wireless from several laptops. Has previously been working great, until just recently.
Hope there is an easy fix.
ciw

HP PSC 1110 All-in-One Printer

HP PSC 2410 All-In-One - use in Windows 7 64-bit environment

Hi,
I have had this HP PSC 2410 All-In-One printer for some years now and it has worked pretty flawlessly in a Windows XP Pro SP3 environment for that time.
Some months ago, I purchased a new computer system and went to the Windows 7 64-bit OS (not interersted in Windows 8 at all) and whilst I have installed the printer successfully and it works, the software suite that came with the printer on the CD will not install for this environment and therefore I no longer have access to the various Maintenance Options that were available under the Windows XP Pro OS, such as the cleaning and Fax options.
Searching for something for the Windows 7 64-bit OS threw up two options - the driver update and the utilities tool wizard. After going down the driver update route, no software suite was available and in fact the update stated that the driver was installed by Windows 7 automatically. That seems to be the case as the printer works fine in print mode, scan mode (from the desktop menu) and it detects SD cards through the slots.
However, there is no software to allow me to fax or clean or do any of the other options available under the HP Suite that came on the CD.
Going down the Utility route got me downloading a file - HPPIW.EXE - that would look at my current printer installation and check with HP for any updates. After many attempts, the utility simply CANNOT find my printer even though it is installed, works properly and even windows sees it! No amount of recycling the ON/OFF button or rebooting the computer allows this utility to detect the printer at all. It is installed via USB on the Windows 7 64-bit Family PC and windows updates are always fully updated.
I am currently considering the purchase of a new HP OfficeJet 8600 Pro Plus to use as the family printer with the Windows 7 system - and move this HP PSC 2410 upstairs to connect it directly to my Windows XP Pro SP3 personal desktop and use the original CD to install it. My Canon IP4200 Pixma has just died on my personal PC upstairs.
However, until I do that, is there any of the Software Suite available that would work in the Windows 7 environment that would allow me to use the various functions such as Fax and cleaning that were available under the old XP environment and obtained via the CD? Was the Suite of software ever updated for Windows 7?
Thank you,
Lee James
West Sussex UK
This question was solved.
View Solution.

Hi BAW9DV,
I hate to hear you are having issues. While there will not is not a specific software utility that will complete the tasks desired, maintenance can be completed from the front panel of the unit. Windows also has an application for faxing from the computer as well that may work with this device. Please see the information below that may enable the functions desired.
Faxing:
1. Use Windows Fax and Scan
   A. Type Windows Fax and Scan into search box
   B. Configure fax machine for use. Click Here to view Microsoft documentation for use. Note: This is a 3rd party website. HP and I are not responsible for content of this site.
   C. Select New Fax
Maintenance tasks from front panel:
Running the Clean Print Cartridges Utility Click Here
Printing setf-test page Click Here
Evaluate test page Click Here
Align the Cartridges: Press setup-Press 5, then press 2
If you the work around options are not acceptable the 8600 model would most certainly meet your needs when compared with this unit. However I encourage you to contact HP to see what upgrade options are available for this unit. It will most likely be another Photosmart model/type unit, but in many cases upgrades are offered at a discounted rate to our valued out of warranty customers. Global contact information can be accessed Here.
P.S. If you upgrade through technical support, be sure to ask about carepacks. Extended warranties may also be available at a discounted rate for upgrading.
Hope this helps!
Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
Please select the "Accept as Solution" button on the post that best answers your question.
I appreciate your input !
Thank You,
I work for HP.

HP PSC 1410 All-In-One no longer prints

Similar Messages

Maybe you are looking for