HP PSC 1410 All in One

My HP Solution Center for this device, with no warning, failed to operate. I can click on the desktop icon or in "All Programs" and get no response. However the HP Photosmart Essential 3.5 , inttaslled at the same time, opens as usual. I can still print and copy with the device.
My operating system is Windows 7 professional. I can still scan with my alternate scanner HP Scanjet G4050, but I have to set it up each time as I only use it for bigger and more accurate (I think) scans. This is used with a desktop.
jw

Hello and welcome to the HP Forums!
I see you're experiencing software issues. I would like to help with that!
I would recommend performing a power reset on the printer. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would then suggest downloading and running the HP Print and Scan Doctor.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Similar Messages

HP PSC 1410 All in One HANG INDEFINITELY with Remote Downlevel Document

Hi, after a few days of setting up my PSC 1410 All In One Printer, which is hooked up to a Compaq Presario V3000 running on Windows XP SP3 with AMD Turion 64x2 processor; and shared print to a Sony Vaio VGN FW33G, and a Mac Pro running on Snow Leopard OS X 10.6
Just yesterday, my printer was jammed with a "Remote Downlevel Document" which I can't remove after using these methods I've researched:
1. "Right Click and Cancel" x [indefinite] times
2. "Right Click and Refresh" x [indefinite] times
3. "Restart" x [indefinite] times
4. "Restart" with printer hooked on/off to the USB x [indefinite] times + [indefinite] combinations of whichever comes first
5. "Unhook USB and Click Start>Run "net stop spooler" and Rehook USB and Click Start>Run "net start spooler" x [indefinite] times
6. Did virus scan for suspicious virus using Anti Vir
7. And in between, combinations of the above x [indefinite] times
8. Search on the internet which obviously there's no real solution
Please help.
Regards,
Bobby

Am (attempting) to print direct from my MacBook - admittedly I did not install any printer drivers during the Leopard (clean) install and am a bit confused as to whether I'm now using the right one, but from what I can gather from the threads like this now littering this forum it wouldn't have made much of a difference. I had infact presumed my problem was just that - that I hadn't the right driver.
Like I hinted at previous; I can reconnect the HP to my old G4 running Tiger and print with no trouble whatsoever.
Trying to print from Leopard brings up the print dialog, and subsequent utility as it should but then nothing - as if the MacBook's not talking with the HP (though it happily recognises it as being there and what model it is etc.).
I have not yet attempted to print over the network, mainly because I couldn't succeed as is. Or tried to scan as it happens (I hardly ever use the built in scanner as I have a better one and the PSC is my backup - I scan a lot in my job).

HP PSC 1410 All In One, have driver problems...............................

I have an HP PSC 1410 All in one printer that I cannot print items from my computer on. When I try to print something from my computer my computer tells me that no driver for the printer is detcted but when I open "MY COMPUTER" and click Devices, it shows the printer listed as operational and that it is functioning properly.

I tried installing the driver and couldn't so I called HP and found out the printer is obsolete and no drivers are available........ they don't support that model anymore , So I'm screwed................

HP Psc 1410 all in one series Printing pink

Printer - HP Psc 1410 all in one series
Operating system - Microsoft windows Vista 32 bit
Ive installed the driver and the software but when i print colour the colour is pink. When I print in black and white it prints fine jsut colour is all pink.
Jamie

Please click here for a possible solution to your problem:
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&product=441115&docname=c00313147
Let me know if that helps.
Please click on KUDOS if you find my solution helpful.

Not able to install scanner part of 'HP PSC 1410 all-in-one'[SOLVED]

Despite trying instructions in the wiki, checking earlier reports of this problem on the forum and trying on reports from google, I am not able to install the scanner part of 'HP PSC 1410 all-in-one'. The command 'sane-find-scanner' finds it but 'scanimage -L' does not. Also xsane and simple-scan program do not find it. Any help will be appreciated.
(I also tried these entries in the udev sane rules:
ATTRS{idVendor}=="03f0", ATTRS{idProduct}=="4d11", MODE="0664", GROUP="scanner", ENV{libsane_matched}="yes"
"SUBSYSTEM=="usb_device", ATTRS{idVendor}=="03f0", ATTRS{idProduct}=="4d11", PROGRAM="/bin/sh -c 'K=%k; K=$${K#usbdev}; printf bus/usb/%%03i/%%03i $${K%%%%.*} $${K#*.}'", NAME="%c", MODE="0666", GROUP="scanner", ENV{libsane_matched}="yes"
but they do not work).
Some previous threads:
https://bbs.archlinux.org/viewtopic.php?id=107474
https://bbs.archlinux.org/viewtopic.php?id=65431
Not able to install sane-dev from AUR; 'makepkg -s' gives error:
==> WARNING: Cannot find the git binary required to determine latest git revision.
Last edited by rnarch (2012-03-28 05:05:09)

Git was not installed. So I installed it and ran 'makepkg -s' again. It ended with following error:
installing saned.conf in /etc/sane.d/saned.conf...
installing dll.conf in /etc/sane.d/dll.conf...
for dir in artec_eplus48u gt68xx snapscan epjitsu ; do \
/bin/sh ../mkinstalldirs /home/sane-dev/pkg/usr/share/sane/${dir} ; \
done
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/artec_eplus48u
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/gt68xx
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/snapscan
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/epjitsu
/bin/sh ../mkinstalldirs -m 775 -g uucp /home/sane-dev/pkg/var/lock/sane
Usage: mkinstalldirs [-h] [--help] [--version] [-m MODE] DIR ...
Create each directory DIR (with mode MODE, if specified), including all
leading file name components.
Report bugs to <[email protected]>.
make[4]: *** [install-lockpath] Error 1
make[4]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[3]: *** [install-data-am] Error 2
make[3]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[2]: *** [install-am] Error 2
make[2]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[1]: *** [install] Error 2
make[1]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make: *** [install-recursive] Error 1
==> ERROR: A failure occurred in build().
Aborting...
Please note the line: Report bugs to <[email protected]>. Is it a bug? Sane-dev was successfully installed by others, eg: https://bbs.archlinux.org/viewtopic.php?id=65431
Last edited by rnarch (2012-03-26 01:11:57)

HP PSC 1410 All-In-One no longer prints

I have an HP 1410 all in one. I also recently updated to Mac OS X 10.5 Leopard. My printer no longer prints. It will show up in the print queue and the status will say printing but nothing will happen. After a few seconds it claims the printer is ready to print and stops any jobs in the queue. I have tried resetting the printer, tested all the connections, power cycled it both with the power switch and power cable, restarted my computer multiple times, I've tried updating the drivers (but I'll try again here in a minute), and I'm out of ideas. Any suggestions?

Am (attempting) to print direct from my MacBook - admittedly I did not install any printer drivers during the Leopard (clean) install and am a bit confused as to whether I'm now using the right one, but from what I can gather from the threads like this now littering this forum it wouldn't have made much of a difference. I had infact presumed my problem was just that - that I hadn't the right driver.
Like I hinted at previous; I can reconnect the HP to my old G4 running Tiger and print with no trouble whatsoever.
Trying to print from Leopard brings up the print dialog, and subsequent utility as it should but then nothing - as if the MacBook's not talking with the HP (though it happily recognises it as being there and what model it is etc.).
I have not yet attempted to print over the network, mainly because I couldn't succeed as is. Or tried to scan as it happens (I hardly ever use the built in scanner as I have a better one and the PSC is my backup - I scan a lot in my job).

HP PSC 1410 All in one Printer not installed

In windows 8 after complete and lastest installation of Driver of HP PSC 1410v All in one, in the Control Pannel, Device and Printer Tab only scanner icon is showing no any printer icon and no other HP Icon, so i can use scanner only of this model but not printer. After reading suggestions I install the windows 7 driver in windows 8 after solution of fatel error here is also only scanner is showing no facility for printing, please help me where I am wrong or whats solution fast plzzzzzz.

Hello Jai_pareek,
Welcome to the HP Support Forums! I see you would like to install your HP PSC 1410 to your computer running the Windows 8 Operating system. You tried downloading the Windows 7 driver but are now getting a fatal error. Please go ahead and start with the steps listed below:
1. Unplug the USB if using a direct connection.
2. Remove the HP PSC 1410 software from your computers Control Panel's Uninstall a program option.
3. Restart the computer.
4. Make sure ALL the PSC 1410 software is gone from the programs list as well as your HP folder listed under the All programs in your Start Menu.
5. Now go ahead and download the software and drivers for your PSC 1410 (DO NOT plug in USB until the software prompts you to):
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-110055-2&cc=us&dlc=en&lc=en...
6. Go ahead and print a test page.
7. If you are unable to print a test page, please run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
Please let me know if this was successful! I will watch for your reply.
Thank you,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Re: how do i install a hp psc 1410 all in one printer without the disk?

how to install?

lection wrote:
how to install?
Install what? If it is the PSC 1410 then what operating system? Do you have a 32 bit or 64 bit version? See my post here.
If a different printer model please start a new thread after reading this post and then provide some details. What printer model? What operating system? How is the printer connected - USB, wired LAN, Wireless LAN, bluetooth?
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP PSC 1410 All-In-One printer problem!

I have a PSC 1410 for a while now and I reinstalled Windows 7 recently and now the printer's not detected but I can scan documents. What could be the problem? It was working fine before I reinstalled Windows 7 and I've obviously installed the drivers.

Click here for troubleshooting tips for blinking lights on the PSC 1400 series printers.
Regards,
Bob Headrick, Microsoft MVP Printing/Imaging
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP PSC 1410 AII IN ONE

I HAVE BEEN HAVING PROBLEM OF GETTING VERY LIGHT SCANS WITH MY 1410 ALL IN ONE PRINTER
FRONT LEFT CORNER SCANS ARE OVER EXPOSED(LIGHT/DIM) AND THE REST OF THE SCAN PAGE IS SATISFACTORY.
HAVE ALSO OBSERVED A TRANSPARENT PATCH ON SCANNING BED WHICH OTHERWISE MILKY IN APPEARANCE, ALL OVER. PROBABLY PATCH MAY HAVE OCCURRED DUE TO USUAL FREQUENT THUMB ACTION ON THE CORNER WHILE TAKING OUT THE PAPER AFTER YEARS OF SCANNING .
ANY GUIDANCE OR DIAGNOASTIC TROUBLE SHOOTING WILL BE MUCH APPRECIATED
TKS

Hi @sdomir438,
Welcome to the HP Forums!
I understand that your scans a very light with your HP PSC 1410, and I am happy to help!
Please follow this guide, Vertical Bands, Lines, or Streaks in Copies, Faxes, or Scans, as it will help with the cleaning of your scanner glass.
Hope this helps!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

HP 1410 all-in-one Scanned Pictures not Saved

Recently upgraded my pc to windows 8.1 but the HP 1410 all-in-one printer scanner will not save scanned pictures. I attempt to "scan to file" but when I click finish I receive the option to scan more pictures or end (done). W"done" when I click done the "solution center" app returns to its home screen.
All other scanning properties are functioning correctly.

Hello there! Welcome to the forums @Dadoo1211
Please first try running the Print and Scan Doctor. This diagnostic tool will check for any conflicts that could be causing the issue. The tool will show you a report at the end. If there was a problem that the tool could not fix, you will notice it in the results. Please let me know the outcome!
Thank you,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

How do I install driver for hp psc 2400 all in one series AND safe wsnmp32.dll Without a Disk?

How do I install driver(s) for hp psc 2400 all in one series ( WIndows 7 laptop) AND a safe version of wsnmp32.dll -- Without a Disk? A tech took the driver off my laptop and I now have no printer/scanner. Help!!
Much thanks!

Hello,
I see that you're having an issue installing the software. I would suggest following this document, which will guide you through several steps on how to resolve the issue.

Can I share HP PSC 1610 All-In-One series printer through Bonjour?

I have an iBook G4, and a Mac Mini (10.4.11- Tiger) with a HP PSC 1610 All In One series printer connected to it by USB. On my iBook G4, the printer comes up under Shared Printers in the Printer Setup Utility but when I click on it, and press Show Info it freezes.. so I was wondering, is there a way to connect to the printer wirelessly with the correct driver (because the driver doesn't show up in the driver list... and the driver is installed.)

Hi my printer psc 1610 hp not picking paper

HP Officejet and PSC Full Feature Software for HP PSC 1210 All in one printer

Hello ,
I have HP PSC 1210 All in one printer but i am using windows 7 system.how can i find
'HP Officejet and PSC Full Feature Software'
compatible for windows 7, in hp.com i sould find the above software for windows xp but for windows xp its not working, my printer physical keys are not working so i need software to do everyything from print to scan, copy etc from my windows 7 laptop itself. pls help with sofware for windows 7

Hi,
There is not a full feature software Win 7 download available for the HP PSC 1210. The following document includes instructions on how to install the in-OS Win 7 driver with instructions on how to scan:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01796879&cc=us&dlc=en&lc=en&os=4062&product=907...=
I work for HP.

How can I fix a check paper error on the HP psc 1210 all in one printer?

Product name/number: HP PSC 1210 all-in-one
OS: Windows 7
Error Msg: Check Paper light flashes
I have verified there are no paper jams, paper is loaded, print cartridges move freely and rollers are clean. Is there a a paper out switch that can fail?

Hi there,
This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

HP PSC 1410 All in One

Similar Messages

Maybe you are looking for