HP PSC 2175 problems in Windows 8

Hello everybody.
I own a HP PSC 2175 since 2002; I've used this printer in Windows XP, Windows Vista and Windows 7 before moving to Windows 8 (and soon to Windows 8.1). I've always been very satisfied with this device.
According to the informations posted on the Microsoft Windows Compatibility Center web site, this all-in-one printer is fully compatibile with Windows 8; HP web site indicates the list of drivers and provides informations about installing the driver for this device by using Windows Update in Windows 8.
Everything was fine during the installation, but I've suddenly noticed that the printer cannot scan via TWAIN, so it's impossibile for me to scan a document either via the Windows Fax and Scan app or via Windows Paint or via other programs (like Adobe Acrobat and Adobe Photoshop).
I use to visit the HP support page for the printer and check for newer and updated versions of the driver, but there is not such.
Should I have to think about replacing this printer with a newer one?
Thank you.
Bye.
Luigi Bruno

Have you tried reinstalling the printer all over again? Try that.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Similar Messages

HP PSC 2175 Problems....

I am trying to set up my PSC 2175 printer through my print server on my network and am about to pull my hair out!
No matter what i do i cannot seem to get it to work; here is what i have done.
I downloaded the new software from HP and hooked up the printer via USB. I was able to make it print from there so then i unplugged the printer from the computer and hooked it into my print server in the hopes that i could go to that printer in my list and switch it from USB to network printing. Unfortunately, this was not the case. I can't switch it.
So, then i add a new printer and hook it up to the print server and it found it with no problem except the proper driver is not able to be chosen for this networked printer. When i had it plugged in via USB it said HP all-in-one 3.1.0 or something along those lines but when i do it through the network it makes me pick a generic postscript pritner option; i don't want that so i go down the list to HP which brings up another list. However, here is where it once again derails. There are plenty of HP printers in the list but no all in one PSC printers. I go to the website and it says that Tiger supports it and you don't need any additional software but i am not seeing it on the list.
I have reset my printing system and re-installed the HP printer driver package from my Tiger disc but still that does not fix the problem.
if you have any ideas i would be more than happy to work with you to try and figure this out because i am about to the end of the line with this.
Thanks
joe

Have you tried reinstalling the printer all over again? Try that.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Windows Printing w/ HP PSC 2175, prints, but settings are weird?

I have an hp psc 2175 printer connected to a PC computer running on XP on my wireless/wired network. (I have a linksys wireless-g router; i connect wirelessly, and the PC is hooked in through one of the four ports on the back WRT54G). I am trying to set up windows printing so that I can print wirelessly through it. I have already set it up without any problems on three other PC laptops and they all print fine. I had initially had some problems with my mac, but then I downloaded the hpijs and ESP ghostscript from http://www.linuxprinting.org/macosx/hpijs/ , however, now that it does print, it is as if it is using three times the ink on each page!! Every page that prints from my computer is as if the words are allin bold. This does not happen from any of the PC laptops, just from my Powerbook. Is there anyway I can change the settings on the remote printer, or what should I do??
Thank You

I have an hp psc 2175 printer connected to a PC
computer running on XP on my wireless/wired network.
oh-oh. Danger, Will Robinson! Danger!
(I have a linksys wireless-g router; i connect
wirelessly, and the PC is hooked in through one of
the four ports on the back WRT54G). I am trying to
set up windows printing so that I can print
wirelessly through it. I have already set it up
without any problems on three other PC laptops and
they all print fine.
This is because HP's Windows drivers support sharing over the network. (Most of them do, anyway. Some don't. But the printers which can't be shared over the network usually have some kind of a warning in the fine print on the box or on the online blurb.)
I had initially had some
problems with my mac,
This is because HP's Mac drivers do NOT support sharing over the network. (There are exceptions, but most HP inkjets don't do OS X sharing out of the box.) Note that HP does not warn Mac users about this.
but then I downloaded the
hpijs and ESP ghostscript from
http://www.linuxprinting.org/macosx/hpijs/ ,
however, now that it does print, it is as if it is
using three times the ink on each page!!
That's strange. It's not supposed to do that. There's something set funny in the printer setup.
Every page
that prints from my computer is as if the words are
allin bold. This does not happen from
any of the PC laptops, just from my Powerbook. Is
there anyway I can change the settings on the remote
printer, or what should I do??
The HPIJS drivers use CUPS and GhostScript. That means that you can play with the settings (IF you know what you're doing!) from the CUPS printer page on your Mac. (Open a web browser, type in http://127.0.0.1:631/.) This site may be of some assistence. <http://www.cups.org/> This PDF file may also help. <http://www.oreilly.com/catalog/lunixpanther/chapter/ch05.pdf>
And then there's this: <http://www.mandrake.demon.co.uk/Apple/osxprint.html>
Note that you'll have to be handy with the command line to use either of the last two.

Psc 2175 windows 7 64 bit - stopped printing

I have an HP PSC 2175 all-in-one printer/scanner/copier. I use an HP Spectre 13 ultra book w/ Win7 Pro, SP1. Windows says the driver is working, printing to port USB001 (virtual printer port) The printer used to work fine, then it stopped. I suspect a windows update broke the driver somewhere, but since the driver is now bundled with the OS I cannot uninstall and reinstall. All I can do is remove the printer and then re-add it, which hasn't worked.
The symptoms are that when printing from Word or PDF a few lines might print in huge font across the top or bottom of the page, and a bunch of blank pages spit out. Using HP Print and Scan Doctor it says it's going through fixing errors, but the test page spits out 2 blank pages. Windows test print spits out 3 pages, 2 blank and one with a single line in huge font across the top. Printing a test print from Notepad also produces 2 blank pages.
Now even Devices and Printers under Control Panel is unresponsive. I'm submitting this, I guess I'll reboot. If anyone has any suggestions I'd appreciate it.
Thanks
This question was solved.
View Solution.

Hello there
Could you try running the Print and Scan Doctor tool? It should fix the issue or at least detect where the problem is coming from. Let me know the results!
Have an awesome Tuesday
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Problems with HP PSC 2175 & HP OfficeJet 6110

I have been unable to get my HP PSC 2175 or OfficeJet 6110 All In One printers to work with my Airport Extreme base station. I have been trying to add the printers on a 12" G3 iBook and G5 iMac (with Panther OS) and a 14" G4 iBook (with Tiger). Neither one will work with the printers connected to the Airport Base Station.
The computers would not even recognize the HP PSC 2175 printer through Rendevous or Bonjour. We switched printers and have been trying the OfficeJet 6110, it is recognized in Rendevous on the G3 ibook and G5 iMac, but they will not add the printer because they cannot find the printer driver, even though I have installed the software for hte printer, and downloaded the newest driver. The 14" G4 iBook will also recognize the 6110 in Bonjour, and apparently finds the driver, but when you try to print, nothing happens... the print job keeps stopping, and will not print.
Any ideas on what the problem is or how to get these printers to work with the Airport Base Station... gosh this is frustrating! Hardly any printers seem to work with the Airport!

The computers would not even recognize the HP PSC
2175 printer through Rendevous or Bonjour.
Is the printer listed in the Airport Admin Utility?
We
switched printers and have been trying the OfficeJet
6110, it is recognized in Rendevous on the G3 ibook
and G5 iMac, but they will not add the printer
because they cannot find the printer driver, even
though I have installed the software for hte printer,
Use the process outlined here:
HP Printers (and others) not on compatibility list and Airport Extreme Printing
http://www.ifelix.co.uk/tech/1300.html
Using the HPIJS drivers.
iFelix

My psc 2175 has a problem with ghost paper jams

my psc 2175 displays paper jam yet there is no paper jam. when i press enter the page that was partially out is drawn back into the printer and then is discharged.

My niece had something similar on her original MBP, and she was told that it was the result of pressure being exerted on the display, like would happen if it were carried in a bag with books. Can you think of any circumstance where your Mac might have been pressured, possibly while in its bag?
My guess is that this is a problem with the display rather than with the graphics card. Have you tried an external display? Graphics card problems tend to also manifest themselves on an external display.
This does not look like the typical spot that you see when there is a bright light shining from the other side of the display. You can certainly cover up the apple with something opaque to eliminate any possibility of this artifact being related to anything shining through the it.
Since the apple is in the middle of the display, it may also represent a point at which external pressure could cause more deflection, and possibly do some damage.
You might try running the extended version of the Apple Hardware test, just in case something might show up in the form of an error code.
Good luck!

My HP PSC 2175 printer spits out blank paper while I try to print.

I have Windows XP service pack 3. My printer(HP PSC 2175 All-in-one) use to work well until few days before. I leave the printer unused for few days and now when I came back to use it , it simply picks up paper scans( a ledger like light runs to and fro at the top end of paper) and spits the paper out.This only happens when I try to print. I can still make black copies well from the same machine. I only have Note pad and Word Pad. It does the same with both. I tried with pdf document too. It still persists its problem. But if I open the Hp service tool box through printing preference and print the test page it prints.
I have tried every thing that I can do. I've repalced the new cartiage, uninstalled the existing driver softer and installed new from hp website. Updated them and what not.
Can you tell me what is wrong with my printer? pls.

Hi,
It looks like you've tried some of the troubleshooting steps listed in this document, but there are a few more to try first. Click on the + besides the XP section and follow the steps in order. See if this helps, if it doesn't I'll look for some more.
Printer Prints Blank Sheets
Say Thanks by clicking the Kudos Star in the post that helped you. Please mark the post that solves your problem as Accepted Solution.
I am employed by HP

HP PSC 2175 All-in-one prints blank pages from word, chrome and notes

My HP all-in-one printer PSC 2175 all-in-one has suddenly decided to print blank pages.
So far I've tried printing from Word, Notes and Photoshop but come up with nothing.
It prints test pages and diagnostic pages without any problems and it makes direct copies without problems.
The diagnostic tool can't find anything wrong.
I've run all the software I could find on Swedish HP.
I've reinstalled the printer, reinstalled Word, repaired Windows, nothing helps.
I have Windows XP, fully updated.
Any suggestions?
HP PSC 2175

I am having this problem too - just prints blank pages. Ran the tests checked cartridges settings sanity nothing.Scans fine.I currently have three duff printers in my office which is more than frustrating...

HP PSC 2175 spits out blank paper while I print.

I have Dell GX520 Desktop PC with Windows XP service pack 3 and HP PSC 2175 all-in-one printer. Since few days I m having trouble printing with my printer. When I try to print it simply picks up the paper scans it and spits out blank paper instead of printing it. There is no any error message or flashing light or any thing in the printer.
But still I can make copy or print the test page from it. The only thing is I can't print any document from WordPad or NotePad or through Adobe Reader. I don't have Office on my PC.
I have tried every thing that I can do. Uninstall the driver and reinstalled it downloading from HP website,updated the drivers manually, replaced new cartridges and what not. But I still have the problem. It would be so helpful if you have any solution to this problem.

I'm having the same problem....
The computer is a hp pavilion.
When trying to print, It loads the paper, It checks the paper position, then it just ejects the paper.
I opened the print job que and watched it.
When the print job ques up, it shows the job...then deletes the job before printing it.
It has been working fine up until a few days ago.
Any help would be appreciated.

HP PSC 1100 drivers for Windows 7

Are there already HP PSC 1100 drivers for Windows 7?
I cannot use the scanner with my new Windows 7 machine.
Thanks!

The PSC 1100 drivers should be pre-installed on Win 7 itself. If just plugging in the printer doesnt work, then go to the Devices window, click on Add A Printer, and when you come to the drivers window, click on Windows update to get the latest drivers from Windows update. This is a legacy product, so HP most likely wont release software and drivers separately.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee.

HP PSC 2175 stopped printing from computer

I have an HP PSC 2175. It's worked just fine until the other day. Now it won't print anything from the computer. I can print a test page from the printer itself, but it won't print a test page went sent from the computer. I have uninstalled and reinstalled the drivers. Tried rebooting both my computer and printer and nothing happens. I use Vista and the printer is connected via USB. Not sure what the issue is, but I NEED my printer to work! Any suggestions?

I am struggling with the same problem with my HP2355. I was in touch with HP support with a Mac expert. He told me that there are no driver updates available for this all in one product and he told me to look for an open source driver (sic!). My all-in one is printing and copying, but he doesn't make a scan since I upgraded my Macbook Pro to Leopard. The only thing I (you?) can do is waiting for versiontracker to come up with an open source driver. PC people (Vista) had the same problem, it is a small consolation, but I bought yesterday a Canon (inktjet printer) instead of a HP. HP for sure knows how to retain customers. good luck Gerard.

When printing/copying pages come out blank on hp psc 2175

When I print or copy the printer processes a page like it is printing but the pages are blank. The ink cartridges are new and the print head (?) goes across the page like it is printing. The printer is an hp psc 2175 and I am using windows 7. The last thing I did on this printer before it would not print/copy was to scan several documents using Windows Live Photo Gallery and this scanned correctly. What can I do to get it to print/copy again?
Thanks!
This question was solved.
View Solution.

When the printer is not printing black ink and printing out blank sheets ... beware the cartidge sometimes does not insert in proper alignment even though you hear the click. Look closely at the cartridge after you insert it. Make sure it is not slightly tilted. And make sure it is dead center, not further to one side than the other because it will not make proper contact. Also 2 more good suggestions here... http://h30434.www3.hp.com/t5/Ink-Toner-Cartridge-Printhead/HP-Officejet-6500-Wireless-will-not-print...
PS- the HP 1210 will print without the color cartridge installed!
Also it is not that hard to refill cartridges yourself. Look how much ink you get for so cheap... http://www.amazon.com/gp/search?ie=UTF8&tag=ie8search-20&index=blended&linkCode=qs&camp=1789&creativ...
--ThatPat

I have a psc 2175 all-in-one that seems to have a bound up (or stuck) scanner/copier bar assembly

please help me, i have a psc 2175 all-in-one & it seems to have a bound up (or stuck) scanner/copier bar assembly. it keeps make a repetitive noise as if it is trying to move but it only moves about half an inch & goes back & tries to do it again & again. i can't afford a new printer at the moment & i really need to copy a couple of forms before i have to work in the a.m.- thx in advance.

Hi - Try the steps in this document. Specifically, you might try solution 3 first.
Hope that helps.
Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
I am an HP employee.

Installation problem on windows server 2008 r2 datacenter edition 64bit

hi
today, i tried to install the current maxdb 7.8 release on my virtual server with a windows server 2008 r2 datacenter 64bit edition os. at the first installation, i got an error message something with "rte runtime error". at this point, the installation stopped.
because of this error, i tried to uninstall the failed installation. this was not possible, in the uninstaller, i didn't see any components, so i can't uninstall.
so i tried to delete the files manually: the entries in the start menu, and the application's path under "program files"... first, i need to kill a process named "serv.exe", that creates a tcp daemon under port 7200... after killing it, the deletion of the dir in program files was successful.
this is very very weird, now my server is "contaminated" with an uncomplete uninstallation of maxdb...
why maxdb 7.8 has problems on windows server 2008 r2 datacenter 64bit edition???
thanks for feedbacks!
regards, jan

> no, because i canceled this virtual server - another method to solve this problem. (i have really no time for things like that..!)
If you take the time to give exact error messages then someone will be certainly able to help
> on windows server 2003, there are NO problems.
Windows 2003 != Windows 2008 - they use a different kernel, a different security system (UAC) and other features that may prevent a succesfull installation in the first place.
I installed a MaxDB 7.8 just today on Windows 2008 R2 and it worked fine.
Markus

Oracle database 11g release 2 installation problem on windows 7 (64-bit)

First of all my windows is not genuine, but on my friend's desktop oracle download and installation worked fine, he chose "create and configure database" options, and it works very well on his desktop, though his windows is also illegitimate. In my case, when I select "Create and configure database" option and pressed 'next",
(Go to my blog to see it with snapshots: Computer Science: Oracle database 11g release 2 installation problem on windows 7 (64-bit))
it asks to select class, I select "Desktop class" and pressed "next". The moment I pressed "next", the whole setup thing disappeared like it was never started. I searched for all possible reasons for why its not getting installed on my laptop, I used registry cleaner s/w, deleted 25 GB of data to create free space if it were the problem, increased the virtual memory to increase the space for RAM, I did almost everything to get this setup working, but I found no success with the "Create and Configure database" option
and
then
I chose a "database software only" option and chose to store in a folder w/o spaces. This way, I got database s/w only and then later I found "Database configuration Assistant (DBCA)" from windows START button and clicked to create and configure database manually. The steps are pretty much interactive and doesn't involve much brainstorming.
The values I filled for
1) Global Database Name : orcl
2) System Identifier : orcl
3) I chose common password for both SYS and SYSTEM
4) while on Enterprise Manager Configuration step, It asked me to create and configure listener in oracle home, so for that too, I typed "netca" in windows START menu and clicked it. There I added a listener.
5) I chose a Storage area which was the Oracle-home itself i.e. where our installation files goes , in my case it is : C:\oracle_base\product\11.2.0\dbhome_1\oradata
6) Then after few more nitty-gritty clicks, we are set to go !
Finally to write SQL code and to create your first TABLE , type "sqlplus" in windows "START" menu and click it when it appears. A command-prompt like window appears , which will ask you for username and password, so here they are :
Username : sys/ as sysdba
Password : (its the one you created in step 3 stated above )
After this you are ready to write your first SQL command.

Is this your solution to your original post at Oracle database 11g release 2 installation on windows 7 (64-bit) ?
Pl be aware that you should not create any custom objects in SYS or SYSTEM schema - you should create any such objects in a separate custom schema.
About Database Administrator Security and Privileges

HP PSC 2175 problems in Windows 8

Similar Messages

Maybe you are looking for