Hp solutions centre software download for windows 7(64 bit) for photosmart 3110 printer?

How & where to get the hp solutions centre software download for windows 7(64 bit) for photosmart 3110 printer? The full hp solutions centre software features such as photo editing, etc that can be utilized for windows 7(64 bit) with photosmart 3110 printer

Hi Nogot7, you will have to share 3100 over your network.
On the XP computer .....
Open Printers and Faxes.
Right-click the printer you want to share, and then click Sharing.
On the Sharing tab, click Share this printer and then type a share name for the shared printer.
On the Win 7 computer ....
Go to Devices and Printers
Add a printer
Add a local printer
Select Create a new port:
Select Local Port for the Type of port:
Enter the network name of the XP computer ie. \\XPcomputername\share name
Install the 3100 driver when prompted (DO NOT use the CD but the Win 7 built in driver)
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

Similar Messages

  • Drivers for Windows 7 64-bit for HP Pavilion 15-p125ng

    Can any one help me with Drivers for Windows 7 64-bit for HP Pavilion 15-p125ng? I'll be very grateful for any answers
    This question was solved.
    View Solution.

    Hi:
    You should be able to use the drivers and software from this model on yours...
    http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=6936...
    When you go to install the graphics you have to install these drivers in this order and reboot after each installation.
    1. Intel chipset installation utility.
    2. Intel HD graphics driver.
    3. Nvidia HD graphics driver.

  • DRIVERS REQUIRED FOR WINDOWS 7 (32-BIT) - FOR HP Pavilion g6-2004tu Notebook

    Hi everybody!
    Today have formatted my Notebook and changed the OPERATING SYSTEM to Windows 7 (32-Bit) (Enterprise Edition)
    Need basic drivers for the my HP Pavilion g6-2004tu Notebook for the following devices, currently being Yellow Highlighted by the Device Manager:
    1. Ethernet Controller
    2. Network Controller
    3. PCI Device
    4. PCI Simple Communications Controller
    5. SM Bus Controller
    6. Some Unknown Device
    7. USB Mass Storage Device (Although it is reading the Flash Drive)
    Your help is requested and reply is anxiously awaited.
    Thanks in advance.
    Best Regards,
    Faraz
    This question was solved.
    View Solution.

    Hello mike_farhat.  I understand you're looking for drivers for your G6.
    Unfortunately there are no drivers available specifically for Windows 7 32-bit.  However, here is a link to the drivers for Windows 7 64-bit.
    Another thing you could try is to install both the HP Software Framework and HP Support Assistant.  Then you can run HP Support Assistant and the application will scan your PC and automatically download and install any drivers which are available.
    I hope this helps.  Have a great day!
    Please click the white star under my name to give me Kudos as a way to say "Thanks!"
    Click the "Accept as Solution" button if I resolve your issue.

  • Is there a "SCCM Package For Windows 7 (64-bit)" for an X220?

    Hey all,
    i found the "SCCM package for Windows 7 (32-bit) and (64-bit)" for ThinkPad X230s here...
     http://support.lenovo.com/en_US/downloads/detail.p​age?DocID=DS034785
    ...but is there one for the X220s as well? I only see ones for M82, M92p M92, and X230
    any help would much appreciated. 

    That sounds great - actually based on our early research that is exactly the route we've decided to go.
    I don't see a document linked in your post, would you mind re-linking?
    Specifically, we'll want to include drivers for lots of x210, x220 and x230 varieties - and there are a lot of them that I don't have available for testing - they are many miles away.
    Appreciate the help!
    EDIT - I found the document linked in another thread and we've used it to pull in all the drivers we require for the 4 models in our environment.  thanks!
    http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mob​iles_pdf/dml_ur_ti_mdt_2.0.pdf

  • HP Solution Center Software ungrad to Windows 7, will not set up the printer in software

    After upgrading from Windows Vista to Windows 7.  This was a clean reinstall of Windows Vista and then the upgrade was in stalled.  I downloaded the new version of the HP Solution Center full and set it up in my computer. 
    The printer is HP Officejet Pro L7580 and I have set up the print in my control panel as wireless connection and my wireless software for has been upgraded for Windows 7 and the printer is properly connected and printing.
    However when I try to set up my printer in the HP Solution Software it will not set up as a wireless connection for my computer.
    Does anyone know how to solve this problem?

    I get printer c8100 series will not work scanner at hp solution center. Please help me out?

  • DRIVERS REQUIRED FOR WINDOWS 7 (64-BIT) - FOR HP Pavilion g6-1201sm Notebook

    Hi everybody!
    Today have formatted my Notebook and changed the OPERATING SYSTEM to Windows 7 (64-Bit) (Home Edition)
    Need basic drivers for the my HP Pavilion g6-1201sm Notebook for the following devices, currently being Yellow Highlighted by the Device Manager:
    1. Ethernet Controller
    2. Network Controller
    3. PCI Device
    4. SM Bus Controller
    Your help is requested and reply is anxiously awaited.
    Thanks in advance.

    http://www.ma-config.com/en
    http://techpp.com/2010/01/12/identify-and-find-drivers-for-unknown-devices-in-windows/
    good luck

  • No drivers for windows 7 64 bit for PI21AG

    I just paid $170 for a Cisco Aironet  802.11a/b/g Wireless PCI Adapter ( AIR-PI21AG-A-K9 ).
    I was suprised to discover that it doesnt have drivers for windows 7 64bit. for the price of one of these it should be able to be supported on windows 7.
    ive tried to run it on compatibility mode for vista and still nothing. this is very fustrating for an expensive product.

    Hello,
    I have the same issue; the Vista drivers don't work for me, the computer hangs; what's worse is that they even hang a computer with Vista.
    What can I do? This is very frustrating
    thanks

  • Is there a driver for windows 7 64 bit for faxphone L80.?

    is there a win 7 64 bit driver for faxphone L80?

    Hello rickr,
    No, unfortunately a Windows 7 x64 driver is not available.  We apologize for the inconvenience this may cause.
    Please contact us to find out about other options that may be available to you.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • Need a drivers (Compaq 3611au) for Windows 7 64-bit

    Hi,
    I've recently installed WIndows 7 64-bit ultimate edition. I'm using Compaq 3611 AU laptop. I tried to download and install drivers for Windows Vista 64-bit but it only installed Display drivers successfully. I cannot find drivers for audio and other devices. Also my DVD also stopped detected after I connnected Idea Netsetter 3G.
    Can anyone send me complete driver set for Windows 7 64-bit for Compaq 3611 AU?
    Thanks in advance.
    Viresh
    This question was solved.
    View Solution.

    Hi, Viresh:
    I can't stay awake anymore and am going to call it a night.
    I have a dv6810us that has the conexant smart audio 221 chip. I upgraded my notebook like you did to W7 64 bit.
    I used this Vista 64 bit conexant audio driver from my notebook's support and driver page and it worked perfectly right from the beginning.
    Give it a try, and I will read the results tomorrow. Hopefully it will have worked for you.
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloa​dIndex?softwareitem=ob-63949-1&cc=us&dlc=en&lc=en&​...=
    Paul

  • Hp deskjet 5940 drivers for windows xp 32 bit

    hello!
    who can help me find a driver for windows xp 32 bit for my hp deskjet 5940?? the drivers that you download from hp website is for xp 64 bit!
    thanks
    Ans

    thanks for your help!
    I tried this but it does not work for my windows xp 32 bit!
    I have tried many a driver but I can not find anyone!
    I do not know what to do ...

  • Laserjet 1300 Driver for Windows 7 64 Bits

    Come on HP - I need the driver for Windows 7 64 bits for my HP Laserjet 1300 series.
    I installed a generic driver which works OK for some applications.
    But when using my Stenograph application the box that should be printed
    around the text on the printed page is NOT correct: I only see the top and left side of the box shifted by 3 inches.

    rainbowdog97 wrote:
    Thanks very much for replying to my message. I got PCL 5 from both places -- from the Windows Update list and from the HP website. If it helps, at the hp website it is at:
    http://h20000.www2.hp.com/bizsupport/TechSupport/S​oftwareIndex.jsp?lang=en&cc=us&prodNameId=238322&p​...
    You can get to it through www.hp.com/go/windows7, where I also got PCL6.
    I have a lenovo thinkpad x300, and connect to the LJ1300 with a USB. I installed PCL5, for example, and tried to print a simple text. But my printer does not respond (the light doesn't start to blink), and when I use the Print function, it gives me a message that indicates "error, 1 document".
    I will be off of my printer for a couple of weeks but want to be up and running soon. I had hoped installation of Windows 7 wouldn't be dramatic.
    Thanks once again.
    The links you cite take you to a page where there are links to:
    HP Universal Print Driver for Windows PCL5 x64
    HP Universal Print Driver for Windows PCL6 x64
    HP Universal Print Driver for Windows PostScript x64
    As the name suggests, those drivers are intended to substitute for the "real" driver that is specific to a given printer. They primarily are intended for use where a network administrator is responsible for a variety of HP printers on a single network. See http://h20338.www2.hp.com/Hpsub/cache/343033-0-0-2​25-121.html  Personally, I found the "Universal Print Driver" impossible to install and configure.  Congratulations on installing it -- even if it doesn't work.
    On the same page that you linked to, there is a link under the heading "Driver" that leads to "Product Support for Windows 7."  That link basically leads nowhere useful for Windows 7.  The conclusion that you're led to by these pages is that the only choice for Windows 7 is one of the Universal Print Drivers.   This conclusion is erroneous.
    I can't reconstruct how I found it, but if you go to the link in my previous post (http://h20000.www2.hp.com/bizsupport/TechSupport/D​ocument.jsp?lang=en&cc=us&taskId=120&prodSeriesId=​...) you'll get to an HP support page for using HP printers with Win 7.  Essentially, this page divides various HP printers into 6 categories and describes your options for each category:
    HP and Windows 7 printer driver options available for the selected product
    HP print driver available
    Windows 7 print driver available
    HP LaserJet AIO/MFP product options
    Product will be supported
    Selected product is not supported in Windows 7
    The Laserjet 1300 is listed as a Category 3, which means that a driver specific to this model is built-in to Windows 7.  This is not the Universal Print Driver.   The catch is that the driver for the Laserjet 1300 isn't available in Windows 7 out-of-the-box (at least, that's what happened in my installation).  It only shows up if you permit Windows Update to update the list of built-in printer drivers.
    I suggest that you completely uninstall your LJ1300.  Disconnect the LJ1300. Then, right click on its icon in Printers and Devices and select "Remove Device."  Then click on any other printer listed and then click on "Print server properties" in the menu bar.  Click on the Drivers tab and Remove the Universal Print Driver (or whatever else looks like it's related to the LJ1300.  Uninstall anything to do with the Universal Print Driver from Control Panel >  Programs > Uninstall a program.
    Now, you can take one of two approaches:
    What I did was just plug the printer in and turn it on.  If you've managed at some point to update the list of built-in printers, Windows should just identify and install the printer like any other USB device.  Otherwise, you should get a popup asking you to give permission to search the web for a driver. Grant the permission.  Windows will find the correct driver and install the printer.
    Alternatively, go to Devices and Printers and start the Add Printer wizard.  Tell it you're installing a local printer to LPT1.  You'll get to the list of built-in printer drivers.  Select HP in the left pane and scroll through the right pane.  If you find the PCL5 driver for the Laserjet 1300, cancel the process and then add the printer as in the paragraph above.  If you don't find an entry for the Laserjet 1300, click the Windows Update button.  After a couple of minutes, the process will be finished, and now when you look there will be the PCL5 driver for the Laserjet 1300.  Cancel the process and add the printer as in the paragraph above.
    Good luck.

  • C4380 hp solution centre software for mac os 10.9

    Just purchased a new Macbook Pro with OS 10.9. I have a HP C4380 printer. I have downloaded the driver software and the printer is working. However, I need to know where I can download the actual "Solution Centre Software" so that I can scan documents etc. Looked everywhere. It used to be available as I have done this before for a windows PC. Very frustrating??

    Hi,
    The HP Solution Center software is only available for Windows, for Mac there are otehr applications for a such.
    Folow these steps to find more about scanning on Mac OS X 10.9 with your printer:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03967506&tmp_task=useCategory&cc=us&dlc=en&lc=e...
    Regards,
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • How do I uninstall Solution Centre Software

    PhotoSmart 2610 All-in-One Printer on Vista PC. Solution Centre software is corrupted . I want uninstall and reinstall so how do I remove it.

    If the Hp Solution center is corrupted
    ..better to completely uninstal;l and reinsatll the software because sonme drivers for your printer might have been corrupted as well...
     try this one....
    Uninstall any remaining Hp printer program from your system..
    1. Click windows logo or start button- on the search box or run - type in %temp%, press enter
    2. look for the 7z folder on the TEmp folders.
    3. Open &z folder and look for util- open util look for ccc folder- open ccc folder loofk for uninstall3.
    4. Procedd to Uninstall level 3- restart the computer -go back to %temP% trhen delete tye 1st 7z folder-- to the same process for the remaining 7z folders- open util-ccc-uninstallL3- restart Pc and delete te 7z folder
    5. Once your'e done- go to add or remove programs or programs and features to uninstall remaining Hp printer software.. then restart you pc again..
    Follow these steps before re-installing the printer:
    Click Start , and then click Run . The Run dialog box opens.
    In the Run dialog box, type msconfig , and then press Enter .
    If the User Account Control window opens with the message 'Windows needs your permission to continue ,' click Continue to close the window.
    In the System Configuration window, click the Startup tab, and then click Disable All .
    Click the Services tab, click the Hide all Microsoft services checkbox, and then click Disable All .
    Click Apply , and then click OK .
    When prompted to restart the computer, click Restart later .
     Restart the network devicesFollow these steps to restart all the devices on the network.
    These steps include turning off the computer. Consider bookmarking this page for ease of reference.
    Press the Power button to turn off the product.
    Click Star,  click Shut Down , and then click Shut Down from the drop-down list.
    Turn on the wireless access point (router).
    Press the Power button  to turn on the product.
    Press the power button on the computer to turn it on.
    When the computer turns on, a System Configuration Utility message opens on the computer. Select the Do not show this message again check box, and then click OK .
    proceed to the installation.......then prove functionality...if successful continue these steps
    Re-enable startup programs and services
    Click Start ( ), and then click Run . The Run dialog box opens.
    In the Run dialog box, type msconfig , and then press Enter .
    If the User Account Control window opens with the message 'Windows needs your permission to continue ,' click Continue to close the window.
    In the System Configuration window, click the Startup tab, and then select the check box next to each program that should run when you turn on the computer. If a program should not run when the computer is turned on, leave the check box clear.
    CAUTION:Do not disable any Microsoft services.
    If no changes should be made to startup programs or services, click the General tab, and then select the Normal Startup checkbox.
    Click Apply , and then click OK .
    When prompted to restart the computer, click Restart .
    Although I am working on behalf of HP, I am speaking for myself and not for HP.
    Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
    If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
    Happy Troubleshooting : )

  • Not able to use HP Solution Centre after installing on Windows 7

    Widows 7 Office Jet 6500 N
    I have reinstalled drivers on 6 occasions, each time a diffenetnt problem. I now have it installed to work on a network and all seems OK except  I have no Solution Centre only HP Document Manager.  It asks me to complete the installation by connecting a USB cable. When I do that it gives me full HP Solution Centre but messes up my printers, insatlling Copy1 and I find I cannot print again. (I have also installed on a XP computer on the same network without any problems, all works properly with Solutions Centte etc)
    Any ideas if I can have the HP Solution Centre as well please
    Thanks  Robert

    Hi
    Thank you for your reply.
    I am not sure that it actually answers me problem.
    I now have the printer and Windows 7 computer set up and working.  The only way I can work the printer for scanning etc is thorugh an icon called HP Document Manager which whilst fine it does not have the refinements that I have ben used to when using the icon HP Solution Centre in the past.  This allosw easier usaeage of scannong etc, ink levels, settings and so on. It is this that I would like to reinstate.
    I am not using a Wireless Network rather a Wired Network
    Thanks
    Robert

  • I can't download itunes 10.3.1 for Windows 7 64 bit

    I can't download itunes 10.3.1 for Windows 7 64 bit.
    I tried the suggestion to delete existing iTunes before installing the updated version.
    I receive a message that a file is in use when I try to delete iPOD.
    I started Task Manager to stop services for iTunes as suggested but it is not listed.
    How do I install iTunes 10.3.1 for Windows 7 - 64 bit?

    I got the same message about the network resource that I can't access.  The only difference is that I couldn't install Itunes 10.3 because I can't remove the old version of Bonjour.  I couldn't get rid of anything in add/remove programs, but I went into my program folders and deleted everything that had to do with Itunes.  I also ran a Windows Cleanup Utiltiy.  Nothing will work.  I still can't remove Itunes, Bonjour, Quicktime, MobileMe Control Panel, Apple Mobile Device Support, Apple Application Support, or Apple Software Update in add/remove programs because they are on a network resource that I can't access even though I deleted them from the program folders.  This is very frustrating!

Maybe you are looking for