HP StorageWorks 20 Modular Smart Array Support / 335921-B1 storage

hey Friends...
i have a storage - HP StorageWorks 20 Modular Smart Array Support / 335921-B1 storage and i have changed the storage connection with other Server..but my problem is driver....when i check device manager it seems HP U320/sata bulk 1 SCSI ARRAY DEVICE hasnt a drive...so i cant connect my storage.
i need help about it. best regards.

Hi:
You may also want to post your question on the HP Business Support Forum -- Disk Array section.
http://h30499.www3.hp.com/t5/Disk-Array/bd-p/itrc-195#.UqtyU-l3u9I

Similar Messages

HP 2312fc DC Modular Smart Array Firmware upgrade

Dear All,
Please guide me hwo to update firmware for HP 2312fc DC Modular Smart Array and provide link to download firmware.

Hello denniswier,
Your question about your server would be better answered by our business department.
Here is a link to the business forums.
Have a good day.

HP Smart Array Disk Mounting(?) help

I have just installed Solaris 10 (x86) on a HP Proliant DL380 G4, this involved applying the driver updates for the RAID controller to allow the Solaris install to work (there have been lots of posts about the RAID controller driver being required for the install to work)
The machine has two raid controllers the onboard 6i controller and the additional HP 6400 controller we've added to hook up the Smart Array disks
I need to know how to mount or add or configure the disks in the smart array. I think i have the driver installed for the 6400 raid controller but the next step i am not sure of. The BIOS let me configure the discs to be a RAID 5 and I was expecting to see the discs in Solaris.
Is anyone able to offer a suggestion ?
Having a HP server with a Smart Array / Storage Works device should be fairly common but Google hasn't turned up anything useful.
Further information (may or may not be useful).
In the Server BIOS i have the following information for the disk array controller:
Logical Drive #1 RAID 5 1955.8GB
Direct Attached Storage
Controller HP Smart Array 6400, Slot 3
The individual disks are (i have 8 in total):
SCSI Port 1, ID 0
SCSI Port 1, ID 1
SCSI Port 1, ID 2
SCSI Port 1, ID 3
SCSI Port 1, ID 4
SCSI Port 1, ID 5
SCSI Port 1, ID 8
SCSI Port 2, ID 0
I don't know what happened to SCSI Port 1 ID 6 and 7.
In /dev/dsk/ i have quite a few disks listed but htey don't seem to map onto the 8 disks, or the one disk logical disk i was expecting solaris to see.
I thought my disk would be something like
c1t0d0 - is the disk which Solaris install found (i think)
c2t0d0 - this is a symbolis link to devices/pci@0,0/pci8086,3599@6/pci8086,329@0/pci1014,la7@2/pciell,409c@4/sd0@0:wd
Is this my second disk ??

Hi:
You may want to copy and paste your post from here onto the HP Business Support Forum -- Proliant Storage Systems.
http://h30499.www3.hp.com/t5/ProLiant-Storage-Systems/bd-p/itrc-265#.UlwBSJAo69I

Solaris 8 install: Compaq Smart Array 431 Controller

How do I get Solaris to recognize the Smart Array 431 controller? It can't find any suitable disks under installation.

I was also wondering why this support was removed since it was in 2.5.1, 2.6, and 2.7? I wish to upgrade my servers to 2.8 however no support for the Array controller. I looked around and Microsoft NT/2000 looks like the only NOS that still contains support for the Compaq Array Smart Controller (EISA). Is it because Microsoft is a Monopoly, or people buy it because they still support legacy hardware/software?

Smart Array P400 and 516814-B21

Smart Array P400 in Slot 6 Bus Interface: PCI Slot: 6 Serial Number:[Personal Information Removed] Cache Serial Number:[Personal Information Removed] RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 512 MB Total Cache Memory Available: 464 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 1 Size: 558.7 GB Fault Tolerance: 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 128 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Unique Identifier: 600508B1001047395356543259490033 Disk Name: /dev/cciss/c0d0 Mount Points: None Logical Drive Label: A37771AEP61630G9SVT2YI734D Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 300 GB, OK) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 300 GB, OK) Mirror Group 1: physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SAS, 300 GB, OK) Drive Type: Data physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 15000 Firmware Revision: HPD6 Serial Number:[Personal Information Removed] Model: HP EF0300FATFD Current Temperature (C): 22 Maximum Temperature (C): 78 PHY Count: 2 PHY Transfer Rate: Unknown, 3.0Gbps physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 15000 Firmware Revision: HPD5 Serial Number:[Personal Information Removed] Model: HP EF0300FARMU Current Temperature (C): 25 Maximum Temperature (C): 55 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 15000 Firmware Revision: HPD6 Serial Number:[Personal Information Removed] Model: HP EF0300FATFD Current Temperature (C): 23 Maximum Temperature (C): 76 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 15000 Firmware Revision: HPD6 Serial Number:[Personal Information Removed] Model: HP EF0300FARMU Current Temperature (C): 27 Maximum Temperature (C): 87 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown As you can see, disk models. Write speed of not more than 5MB / s If you make an array of disks only one model - more than 300MB / s What can be done?

Hi:
You may also want to copy and paste your issue on the HP Business Support Forum -- Disk Array section.
http://h30499.www3.hp.com/t5/Disk-Array/bd-p/itrc-195#.Urmg1-l3u9I

SCSI Lead for DL380 G5 - HP Smart Array 6402 to HP MSA30 Ultra 320 IO

can anyone help please?
I need a short SCSI lead to connect HP Smart Array 6402 to MSA30. Both ends are the same size really small and slim.
Can anyone help please?

Hi:
You may also want to post your question on the HP Business Support Forum -- DL Servers section.
http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/bd-p/itrc-264#.UuUlN-nna9I

MIBs required for "HP Smart Array P420/1GB FBWC"

Hi,
One of our customer purchaged "HP Smart Array P420/1GB FBWC
" to integrate that we required the following details.
-          MIB
-          Alarm Documentation
-          Alarm List
-          Features like AlarmUpload
                 Is it supported?
                 If yes how to perform(eg., set based/get based etc.,)
Could you please help in getting the above details for "HP Smart Array P420/1GB FBWC"
Thanks in advance.
Ezhil

Hi:
You may also want to post your question on the HP Business Support Forum -- ProLiant Storage Systems section:
http://h30499.www3.hp.com/t5/ProLiant-Storage-Systems/bd-p/itrc-265#.VG4Bo3ktC9I

Oracle Ent. Linux drivers for HP Smart Array B110i Sata Raid Controller

Trying to install Oracle Ent. Linux (OEL) release 4 update 8 on HP DL 180 G6 server. Where we can find OEL drivers for the sata raid controller ?
(HP Smart Array B110i Sata Raid Controller)
Thanks in advance.

The HP support side shows a Linux certification matrix at: http://h18000.www1.hp.com/products/servers/linux/hplinuxcert.html
From there you can also download the necessary drivers and instructions or use HP smartstart CD which prepares the system for the OS you need to install. Oracle Enterprise Linux is binary compatible with RHEL. You will need to click on "Archive" to see support for Enterprise Linux version 4 and older.
Also interesting should be Red Hat Enterprise Linux Technical Exceptions at
http://h18000.www1.hp.com/products/servers/linux/supportmatrix/rhel/exceptions/rhel-exceptions.html

Can my server work without smart array controller

I have HP Proliant ML570 server with P400 smart array controller card. I suspect smart array controler is not working. Can I remove array controler card and continue to work without any raid config. Please suggest.

Hi:
I recommend you also post your question in the HP Business Support Forum -- ML Servers section.
http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/bd-p/itrc-264

Smart Array P800 Controller Accelerator issue

Hello there.
We are running a DL180 G6 with a Smart Array P800 disc controller and 8 harddrives in RAID 5.
When logging into the server using HP System Management Homepage it states that the 'Accelerator' is disabled, and this accelerator have brought us lots of grief.
This particular disc controller are using two batteries to power a disk cache, and initially we interpreted this issue as coming from faulty batteries and replaced the first one, and then both.
This did not address the error message.
As that did not address it we have since then done the following:
Verified configuration
Cleared IML
Upgraded BIOS
Upgraded iLO
Upgraded HP server firmware+drivers
Upgraded centos
Restarting the server and booting to it using ACU:
#ctrl all show
Smart Array P800 in Slot 2
#ctrl all show status
Smart Array P800 in Slot 2
Controller Status OK
Cache Status OK
Battery/Capacitor Status OK
View controller info
#ctrl slot=2 show
Smart Array P800 in Slot
Bus Interface: PCI
Serial Number: PAFGF0M9SWF1AO
Cache Serial Number: PA82B0A9SWE37U
RAID 6 (ADG) Status: Enabled
Controller Status: OK
Hardware Revision: Rev E
Firmware Version: 7.22
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 secs
Surface Scan Mode: Idle
Queue Depth: Automatic
Monitor and Performance Delay: 60 min
Elevator sort: Enabled
Degraded Performance Optimization: Disabled
Inconsistency Repair Policy: Disabled
Wait For Cache Room: Disabled
Surface Analysis Inconsistency Notification: Disabled
Post Promt Timeout: 0 secs
Cache board Present: True
Cache Status: OK
Accelerator Ratio: 25% Read / 75% Write
Drive Write Cache: Disabled
Total Cache Size: 512 MB
No-Battery Write cache: Disabled
Cache Backup Power source: Batteries
Battery/Capacitor Count: 2
Battery/Capacitor Status: OK
SATA NCQ Supported: True
Firmware version in use is 7.24, which is the latest version
Driver version in use is 3.6.28-RH3 (cciss, as hpsa is not compatible)
cciss is now part of the main linux kernel and should be upgraded with a yum update
The latest HP Service Pack for Proliant (2014.02.0B) is installed
The latest BIOS is installed (2013.07.01 A)
The iLO software is updated to the latest firmware (4.26)
A yum update have been issued.
Neither of the above have addressed the issue.
The only time this error message is cleared is shortly after a reboot - but it then re-occurs approx one day later.
Have anyone else experienced this issue or have any information in regards to how to fix it?
Any help would be much appreciated.
Regards,
Olof Nord
ccelerator

Hi:
You may also want to post your question on the HP Business Support Forum -- DL Servers section.
http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/bd-p/itrc-264
or the Proliant storage systems section...
http://h30499.www3.hp.com/t5/ProLiant-Storage-Systems/bd-p/itrc-265

Some basic HP Smart Array questions

Hopefully a simple answer to what seems to be a fairly simple question...
If, for example, you have a P800 HP Smart Array with 24 disks and a spare and you want to partition a number of database files across drives to maximise I/O performance (the transaction log file is heavy on writes and the other data and index files are heavy on reads), would it be better to:-
a) Use the 24/25 disks to create one SAS Array and three logical drives:-
SAS Array A with spare - 3 Logical drives
     Logical Drive 1 (1200 Gb, RAID 1+0)
     Logical Drive 2 (1200 Gb, RAID 1+0)
     Logical Drive 3 (1200 Gb, RAID 1+0)
b) Use the 24 disks to create three SAS arrays each with one Logical Drive:-
SAS Array A & Logical Drive 1  (1200 Gb, RAID 1+0)
SAS Array B & Logical Drive 1 (1200 Gb, RAID 1+0)
SAS Array C & Logical Drive 1  (1200 Gb, RAID 1+0)
Not sure how the Spare disk fits into Option B?
Anyway, if the objective is to maximize I/O performance, is it Option A or B?
The phrase, 'logical drive'... Does this mean that I/O is partitioned at the logical drive level or does the HP Smart array controller spread the I/O across the SAS Array? If I look at I/O counters (eg. Perfmon on Windows Server), I can see that Logical drives as in Option A seem to be separated completely as one logical drive could have a disk queue and other logical drives on top of the same SAS array will not have a disk queue.  What are the prose and cons of Option A and B? Understanding these issues will help me to come up with the right configuration in terms of arrrays and logical drives.
Thanks in advance,
Clive

Hi, Clive:
I'm not so sure yours is a fairly simple question for the HP consumer notebook forum.
You may want to copy and paste your post in the HP Business Support Forum -- Disk Array section.
http://h30499.www3.hp.com/t5/Disk-Array/bd-p/itrc-195

[SOLVED] Unable to boot after last upgrade [HP Smart Array]

Hello guys.
After last upgrade I'm unable to boot. I have fileserver with 2 discs in HP Smart Array RAID 1.
While booting, kernel is unable to find my raid (should be cciss) and therefore lvm2 hook fails to find root partition. While going into recovery, I can chroot without an issue, lsmod shows that cciss driver is properly loaded, disk exits in /dev/cciss/, logical group and volumes are detected properly.
No matter what I do, I just can't get cciss module into kernel. Putting in MODULES in mkinitcpio.conf's MODULES="" didn't help. I'm listing my initramfs images and there is no cciss.ko. I'm also searching for module in my filesystem and can not find it.
Any help will be appreciated.
Last edited by edke (2012-06-04 10:39:20)

Thank you for your quick reply.
DSpider wrote:First of all, have you tried the Fallback entry? Because initramfs-linux-fallback.img is supposed to have a full range of modules.
Of course, no change.
DSpider wrote:
Second, after editing /etc/mkinitcpio.conf you need to regenerate your initramfs.
# mkinitcpio -p linux
But the MODULES section needs to have something in there...
Here's mine:
MODULES="pata_amd sata_nv ehci-hcd ohci-hcd ext2 ext3 ext4 vfat snd-hda-intel"
You probably need "mdadm" or "mdadm_udev" in there too, I'm not sure... I don't use RAID, but maybe these will help:
https://wiki.archlinux.org/index.php/Mk … Using_RAID
https://wiki.archlinux.org/index.php/So … ID_and_LVM
HP Smart Array is hardware RAID, therefore I don't need mdadm. Right module should be cciss, but this is somehow not working. Adding this into MODULES does not add cciss module to image.
When I'm booting from Arch install for recovery and chroot, cciss is loaded and my HP Smart Array disk is visible.

Install solaris 10 on Proliant 1600 - Compaq Smart Array 221

I'm trying to install solaris 10 06/06 on a Proliant 1600 with smart array 221.
I boot from the cd and choose the first option (Solaris), then I get this warning:
WARNING: failed to program IO space [0/20/2] BAR@0x20 length 0x20
and the system hang up.
Does anyone know to what it is related to?
Thank you
Andrea V

I have the save problem when installing Solaris 10 on my System.
my configuration:
Proliant 1600
Compaq Smart Array 221
1 CPU 550mhz
512M RAM
It would be nice if somebody could help.
Edit:
The system crashes in the same way when I try to boot the "install check CD 1.1."
Message was edited by:
darthich

Availabilty of firmware version 6.40 for Smart Array p410 controller on the HPSC portal

Hi,
May I address a query in reference to the availability of storage firmware version 6.40 for the Smart Array p410 controller on the HPSC portal.
When I search for the 6.40 version for the HP Smart Array P410/256 2-ports Int PCIe x8 SAS Controller
- Microsoft Windows Server 2008 x64 I don't see the download.
http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=4091409&spf_p...
Many thanks.
Best regards,
Ryan

Hi,
May I address a query in reference to the availability of storage firmware version 6.40 for the Smart Array p410 controller on the HPSC portal.
When I search for the 6.40 version for the HP Smart Array P410/256 2-ports Int PCIe x8 SAS Controller
- Microsoft Windows Server 2008 x64 I don't see the download.
http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=4091409&spf_p...
Many thanks.
Best regards,
Ryan

Compiling rdesktop with Smart Card support?

Hello,
I've tried like the dikens to compile "rdesktop" (an open source solution to connect Windoze PCs using Microsoft RDP protocol). I can compile and run the source code, but I find it impossible to compile in smart card support. I've tried everything to get the "pcsc-lite" components to compile in - but I'm too much of a makefile noob I'm afraid.
Anyone know how to do this?
There's a related discussion at http://discussions.apple.com/thread.jspa?messageID=8652963.
Any help appreciated
~Matt

Hi,
Thank you for posting in Windows Server Forum.
In a Remote Desktop scenario, a user is using a remote server for running services, and the smart card is local to the computer that the user is using. In a smart card logon scenario, the smart card service on the remote server redirects to the smart card reader
connected to the local computer where the user is trying to log on. You can refer following article for details.
Smart Card and Remote Desktop Services
http://technet.microsoft.com/en-us/library/ff404286(v=ws.10).aspx
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support

HP StorageWor​ks 20 Modular Smart Array Support / 335921-B1 storage

Similar Messages

Maybe you are looking for

HP StorageWorks 20 Modular Smart Array Support / 335921-B1 storage