HP t510 Thin Client and USB Printer Redirectiion

We have HP t510 thin clients connecting to server side XenCenter and running Windows 7 virtual sessions hosted on the server. We are trying to connect a USB lablewriter printer to one of the thin clients. On the t510 device, XEN Connection General Settings Manager/Local Resources/Local Device Redirection is selected for Printers/Printer Mapping. Also on the t510 device under Peripherals/USB Manager, Protocol/All USB is set to Citrix and Devices has the USB printer selected/checked and set to Redirect.
We have also tried within the assigned Windows session, a registry key has been created under HKLM\SOFTWARE\Citrix\ICA Client\GenericUSB\Devices, using both a generic redirect for all usb printers as well as device specific using the VID and PID hardware information of the printer.
When we have booted into the Windows session and have installed the USB drivers/printing software and physically conencted the usb printer, it is not being recognized by Windows at all. Device Manager is not showing any unknown devices or anything.
Has anyone seen this same issue? Is there an easy workaround? Will there need to be a hardware policy written in XENCenter?
Thank you,
Gregory Hall

Hi Mitchell,
You might get better assistance on the HP Enterprise Business Forum since you have a business class PC.
I'll also ask a moderator to escalate your issue.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Similar Messages

  • Synchronization HP t5335z Thin Client and USB GPS trip recorder

    Can't connect USB GPS trip recorder to my terminal server through HP t5335z Thin Client. Any suggestions?

    Hello Tony-CCS,
    Your system is one of our business units.
    Your question may be better answered on our business forums.
    Here is a link to the business forums.

  • How to join T510 Thin Client to Domain

    I need to join my Hp T510 thin client devices to my Windows domain. (I need to place them all in a certain OU in Active Directory). Is this even possible? I have been reading around about this, and I get the feeling that some people have managed to do this, but I don't know how. Any help please? (I have been able to do it with my T520 devices, but the T510s are different). 

    I'm not aware of any particular tie-in between Windows 7 and Domain Controller and Samba and OS X Server Open Directory LDAP Services.
    Samba did provide limited Domain Controller capabilities and can use Domain Authentication, but the Apple installation from 10.6 is an old release and I've had some problems getting that older stuff to work.  You'll likely have to hand-manage Samba to get this to work, by following the directions at the Samba.org web site, too.
    The best resource I've encountered for digging around in this topic area is the archives of the Mac Enterprise mailing list.
    FWIW, Microsoft has (migrated from? abandoned? deprecated?) Domain Controller authentication in favor of Active Directory some years ago, and Apple has abandoned Samba in more recent releases; this is a dead end.  If you are using Windows Server and Active Directory, then OS X Server can be configured in what's called a Magic Triangle configuration; where you have Windows handling Windows authentication, and OS X Server handling OS X authentication, and coordinating across the two.  Or (with newer OS X releases) Apple has improved integration with Active Directory.

  • Diff between Thin client and Rich client

    Hi Everyone,
              Can someone give me a clear picture of the what is the diff between Thin client and Rich client.
    Thanks,
    Krishna

    Hi,
    thick client (rich client) has/stores all the data inside itself
    so it can do application processing without the server with data
    thin client uses resources from host computer (from server)
    and wihtout that you are not able to work with that kind of client
    does that answer your question ?
    Regards,
    michal

  • HFM Thin Client and Thick Client

    Hi
    can anyone tell me what is HFM thin client and thick client
    Thanks

    Thick client is the actual application client view. Most administrators limit that view to only them and provide a workspace (the thin client) as a method of accessing hfm. This is because more can be done in terms of metadata and security changes in the thick client than the thin client.

  • Print to lpt1 where remote desktop client has usb printer

    I have a client with an usb printer and need to print an UPS label report from Microsoft Dynamic NAV on an remote server that prints only to LPT1. I've set the client printer as shared printer and selected LPT1 and USB ports.  When the client is connected
    to the server through remote desktop, the redirected printer can print a test print but running the report from the application on the server will not print  to the client's printer.  The report shows that it was sent to LPT1 but there are no errors
    or print jobs in the printer queue.  I've also tried to use "net use" to set up the shared printer to LPT1 but that didn't work either.  And I've installed the printer on the server to LPT1 as well and that did not work either. 
    Any help is greatly appreciated.  The server is Windows Server 2008 R2 and the client is Windows 7.
    Thanks,

    Hi,
    As this thread has been quiet for a while, we assume that the issue has been resolved. At this time, we will mark it as ‘Answered’ as the previous steps should be helpful for many similar scenarios. If the issue still persists, please feel free to  reply
    this post directly so we will be notified to follow it up.
    BTW,  we’d love to hear your feedback about the solution. By sharing your experience you can help other community members facing similar problems.
    Thanks for your understanding and Support!
    Regards.
    Dharmesh Solanki
    TechNet Community Support

  • AE and USB Print / Scan / Copy with HP PSC-2410

    My Airport Express finds my HP printer immediately upon plugging the printer into the AE USB port. Printing to it from various macs around the house has been wonderful...but...In order to use the HP's other functions, such as scanning and copying, it seems that the printer must be directly connected to a mac in order for these functions to work.
    Another poster said that he could not check his ink levels on an Epson printer through an AE USB connection, but could once he directly connected the printer to his Mac.
    It seems that the AE will only act as a print server and will not allow for any other features to be shared.
    Anyone else find this to be the case? Is there a fix? It is a pain to have to unplug from the AE and plug into the Mac every time I want to scan something.
    Thanks!
    STEVE

    ...but...In order to use the HP's other functions, such as scanning and copying, it seems that the printer must be directly connected to a mac in order for these functions to work.
    That is true. The USB port on the AirPort Express suppports only printing.
    Another poster said that he could not check his ink levels on an Epson printer through an AE USB connection, but could once he directly connected the printer to his Mac.
    That is also true. Those utilities depend on a direct USB connection to the printer. See KB 107430, AirPort Extreme, AirPort Express: Can't use USB printer utilities while printer sharing.
    It seems that the AE will only act as a print server and will not allow for any other features to be shared.
    That is exactly correct.

  • Bt Infinity hub and USB printing

    Hi all.
    I have recently got BT Infinity and the new homehub required. I am liking the service though the new hub does not allow me to plug a printer into the USB port on the back.
    I know the homehub does not officially support printing, but my previous homehub (version 2) allowed me to plug a printer into the usb port and use 192.168.1.253 as an ip address.
    When I plug the same printer into the new infinity hub the homehub page says that nothing is connected to the usb port. If I plug a flash drive into the port it is recognised straight away.
    When I plugged my printer into the usb port of the old version 2 homehub the hub page recognised the printer was plugged into the usb port and even gave the name and model of the printer.
    Has anything changed that for the infinity hub that would make adding a usb printer impossible? Does anyone else with infinity have a usb printer plugged into the back of their hub? If so how did you get it to work?
    Any help/info on this matter would be grately appreciated.

    Having the same issue.
    What a shame I have to leave my old wireless router plugged in just so that I can use the shared printer.
    Is there a reason this is disabled?

  • DSL-2750B and USB Printer Support

    I just got a DSL-2750B modem/router. In the specs on this page it says it supports a USB Printer:
    https://teleproducts.verizon.com/fileshare/plm/brochure/DL2750BVOL_brochure.pdf
    On the D-Link Site the manual for this router shows screens to configure it. but those screens don't match the screens I get when I log in to the router. The ones on the router are all branded with Verizon.
    If I open the Verizondrive icon showing up in my network I see a folder for Drives and one for Printers.  I have tested a USB drive in the USB port on the router, but can't configre a USB printer.
    I have talked/chatted with the DSL support folks and they can't help. They told me I had to go to premium support and pay for the call.  That doesn't seem right that I have to pay for information on how to configure a device you sold me for a feature that your web site says the device has.
    Please tell me how to configure a usb printer for this DSL-2750B

    TexasDSL wrote:
    I have spent a couple of hours looking for the same information without success. I agree: this seems to me to be basic iinstruction, and Verizon support should provide it without charge .Is anyone at Verizon support listening? Thanks in advance for your help.
    I think perhaps you are a bit confused. This is a peer-to-peer support forum. Posters are fellow end-users like you unless noted as a Verizon Employee via rank and/or avatar.
    If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

  • WebLogic 10.0 JMS Thin Client and JVM 1.4

    As mentioned in [WebLogic JMS Thin Client|http://download.oracle.com/docs/cd/E11035_01/wls100/client/jms_thin_client.html#wp1026979], it can be used on JVM 1.4 client, but it seems that wljmsclient.jar and wlclient.jar compiled using java 1.5 compiler with no 1.4 compatibility.
    Where can I get a 1.4 complied version of this jars for WebLogic 10 ?
    Edited by: user10385140 on 02.10.2008 2:32

    Hi,
    The doc is correct that the 1.4 JVM is supported for thin 10.0 clients, but note that 1.4 is not supported for 10.3 (the latest version). If you confirm that there's a problem, I recommend contacting customer support. Meanwhile, as a work-around, you can use a client jar from an earlier version (such as 9.2 at the latest MP).
    The latest updated version of the 10.0 client doc is at http://edocs.bea.com/wls/docs100/client/basics.html, the link you provided points to an older version of the edoc.
    You might want to look at using a generated "full client" rather than a thin client unless a smaller jar size is important in your use case. The reasoning is stated in the updated edoc.
    Regards,
    Tom Barnes
    WebLogic JMS Developer Team
    Edited by: TomB on Oct 2, 2008 6:52 AM

  • What is thin client and Fat Client

    Hi Experts,
    I would like to know about Fat Client and Thin client in detailed words.
    Thanks and Regards.
    Chilla..

    Hi Chilla,
         The thin clients are clients that reduce the load on servers.
    Let me explain hw thin clients will get works.
         Thin clients are stores,all required library files in you local system,so that the  corresponding applications which are using will be used the library files in your local system and it get execute and where as in the case of Fat clients the library files are not stored in your local system.
       Please let me know if you have any doubts regarding this.
    Thanks and Regards,
    Chandu.

  • Difference bewteen thin client and thick client

    Hi:
    can someone explain the difference between the thin client app and thick client app?

    Thin Client: Little to no logic on front end. Typically a 3 tier architecture. Example is a web browser
    Thick Client: Typically a client-server type architecture where some business logic/processing occurs on the front end

  • Wyse Thin Clients and 2008 R2

    We have updated our site server to Windows 2008 R2 and now we are experiencing sporadic issues with our Wyse thin clients D90D7. After the server OS upgrade, some of our thin clients are experiencing memory leaks.  Anyone come across this?
    Thank you!!!

    I would recommend that you contact Wyse Technical Support for assistance. Maybe there are some fixes to install on the application side.
    This posting is provided AS IS with no warranties or guarantees , and confers no rights.
    Ahmed MALEK
    My Website Link
    My Linkedin Profile
    My MVP Profile

  • OracelAS Report services, Thin Client and JBoss

    Dear all:
    I have to run my oracle reports using Jboss. What I understand is this that I need to have Oracle AS, and oracle Thin Client to accomplish this. Please tell me from where I can find Oracle thin Client on oracle website.
    My second question is this that I have installed Oracle AS but the opmn.xml file has no <ias-component > for report server, please tell me why it is not there...
    I would be grateful for ur help

    I have installed the Oracle AS and the reports services... I have also installed the Stand Alone J2EE Thin Client (http://www.oracle.com/technology/products/reports/htdocs/getstart/examples/Tools/index.html)
    My current web project uses JBoss and I have to show oracle reports keeping the current environment.
    I have followed the steps provided on the doc mentioned in the above link.
    first i did the following steps ( please refer to the text of that readme doc below)
    (//text of readme doc, I have done these steps
    1. Deploy THINCLIENT_HOME/reports/j2ee/reports.ear on the J2EE application server.
    2. Add the following JAR files to the classpath of the J2EE application server:
    * THINCLIENT_HOME/reports/jlib/rwrun.jar
    * THINCLIENT_HOME/jlib/zrclient.jar
    3. Use THINCLIENT_HOME/vbroker4/lib/vbjboot.jar while starting the application server.
    but i cannot understand what is written just next to the above llines in that doc I am pasting those points from that doc
    (text of readme doc:
    The following section provides detailed instructions on carrying out the above 3 configuration steps with OC4J Standalone Distribution 10g (9.0.4). You need to consult your J2EE application server's documentation to carry out the same steps for your application server.
    1. Add the following to OC4J_HOME/j2ee/home/config/server.xml
    <application name="reports" path="<THINCLIENT_HOME>/reports/j2ee/reports.ear" auto-start="true" />
    2. Add the following to OC4J_HOME/j2ee/home/config/http-web-site.xml
    <web-app application="reports" name="web" root="/reports"/>
    3. Add the following to OC4J_HOME/j2ee/home/config/application.xml
    <library path="<THINCLIENT_HOME>/reports/jlib/rwrun.jar"/>
    <library path="<THINCLIENT_HOME>/jlib/zrclient.jar"/>
    according to what i understood i went to OC4J which is under my Oracle_Infra directory and then completed the above steps
    after that I ran the command (according to this doc):
    java -Xbootclasspath/p:<THINCLIENT_HOME>/vbroker4/lib/vbjboot.jar -jar oc4j.jar
    the result of this command is following
    06/02/09 14:57:37 Oracle Application Server Containers for J2EE 10g (9.0.4.0.0) initialized
    and then it never comes back to command prompt
    Now after all these steps...i don't understand what to do next and my problem is still there which is How to deploy reports made by oracle reports from my web project links
    please help
    Waqas

  • NetWare Queues and USB Print Servers

    Hello good people,
    We usually use HP JetDirect en3700 (J7942A) USB print servers when we have
    to, which work well.
    However, there is severe constraint in the supply chain at the moment.
    Do any of you have a suggestion for an alternative USB print server that
    supports printing from a queues environment? Willing to look at any brand
    or manufacturer.
    Thanks.
    Andrew

    Jdvb,
    > one of my LPT printers stopped working, and well, USB printers are more
    > available.
    > How do I get a USB printserver to service my NetWare 6.5 queue.
    >
    > I have ordered a D-link DPR-1061 printserver, though I am unsure of how
    > to set it up in Nwadmin or something similar.
    > My suplier stopped support for NetWare and I am basically clueless of
    > how to work with NetWare.
    >
    > The Novell Netware printer works primarilly on IPX.
    >
    > I am unsure of how to make it work, the printserver also supports
    > unix/Appletalk which I also see as options in Nwadmin when I add a
    > printer.
    > Though when I load Pserver and then the printserver it fails to load
    > the driver for either appletalk/unix.
    >
    > please help
    > Please help.
    You need to install and configure NDPS (iPrint). The procedure is covered
    in the docs and queue-based and NDPS can coexist. You then create a
    printer in NDPS, have it service the queue. For output you use ypur
    printer, configured as LPR.
    - Anders Gustafsson (Sysop)
    The Aaland Islands (N60 E20)
    Novell has a new enhancement request system,
    or what is now known as the requirement portal.
    If customers would like to give input in the upcoming
    releases of Novell products then they should go to
    http://www.novell.com/rms

Maybe you are looking for