HP TouchSmart 600 and HP psc 2210 all-in-one printer

Hi SiobhanF,
I just registered and this is my first post.
I recently bought a new PC...an HP TouchSmart 600.  My printer is a HP psc 2210 all-in-one.  I need advice on whether the two are compatible and if so how to get them working together.
Thank you,
waj

This is likely caused by the failure of one of your cartridges.  Remove the black cartridge and print a test page.  Does the printer print at normal speed?  Is so the black cartridge was the issue and should be replaced.  If not then put the black cartridge back in and remove the color cartridge and print test page.  If the printer now prints normal speed the color cartridge was at fault and needs to be replaced.
Bob Headrick,  HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

  • Windows RT and HP PSC 1510 All-in-One printer connection

    Hi, I have a Windows 8.1 RT tablet (Microsoft Surface 2) and a wired HP PSC 1510 All-in-One printer. Now when I plug in the printer via the USB, there is no driver that can be found to make this printer work with my device. Anyone have this problem or any solutions? I've tried looking at HP support and nothing there has been helpful.
    Let me add that on the Microsoft Surface, you cannot run .EXE files which are the file types of the HP drivers.
    Thanks ahead
    This question was solved.
    View Solution.

    Hi,
    I afraid the printer is not supported on Windows RT, as you may find listed within the following support document:
    http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c03168175&tmp_task=prodinfoCategory&cc=us&dlc=en​...
    Regards,
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • HP PSC 2210 all in one printer - slow printing

    I have had this all in one printer for several years.  Just recently I attempted to print two pages from a PDF file and it took over 1 hour to print.  At first I thought it was the PDF but now I realize it is with anything I try to print.  I went through all the troubleshooting steps and none of them have fixed the problem.
    I have a Dell Dimension 8400 Intel Pentium Computer,  Windows XP 4 cpu 3.20 GHz, 3.19 GHz, 1.00 GB of Ram.
    It will begin to print but then it will take at least an hour to print 1 page.  I have already uninstalled, re-installed, etc...
    This question was solved.
    View Solution.

    This is likely caused by the failure of one of your cartridges.  Remove the black cartridge and print a test page.  Does the printer print at normal speed?  Is so the black cartridge was the issue and should be replaced.  If not then put the black cartridge back in and remove the color cartridge and print test page.  If the printer now prints normal speed the color cartridge was at fault and needs to be replaced.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • Windows 7 and HP psc 1317 All in One printer

    A friend has a new laptop with Windows 7 installed. I am trying to install the software for his HP psc 1317 series all in one. I have down loaded the drivers etc from the HP site but despite running it as an administrator, both from the original disc and the download, it hangs up half way through telling me to run it as an administrator which I am. (The run as command no longer exists in Win 7) As the 1317 is an old unit but worked perfectly in XP do we have to throw it away which is a shame? I have gone into setup in the software and clicked to run as administrator but to no avail.
    Message Edited by qkjb on 11-19-2009 02:53 AM

    I am not sure about the driver you are trying to install...however here is the correct drivers for PSC 1317 with Windows 7 Support:
    ftp://ftp.hp.com/pub/softlib/software11/COL30219/al-75052-1/AIO_CDB_NonNet_Full_Win_WW_130_141.exe
    I am an HP employee.
    Regards,
    Vidya
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
    ***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***

  • HP psc 2210 all in one printer hung up

    My HP PSC 2210 is stuck with an internal software hang up. It thinks it is printing a job, but there is no job, it also (correctly) wants to align the cartridges, but when I press enter to do this is says it is busy printing.
    (I have cleared any print jobs from the computer print queue).
    It will not copy or anything either , because it is trying to align the cartridges. any attempt to print test pages etc similarly fails, whether from the computer, or direct from the printer.
    I need to reset the internal memory of the HP PSC 2210 in some way.
    I have tried powering up with # and 6 held down, this effected some sort of reset, I had to choose the language again.... but I cannot get rid of the phantom print job.
    I cannot even switch the wretched thing off with the power button any more ?!
    any advice greatly appreciated

    This is likely caused by the failure of one of your cartridges.  Remove the black cartridge and print a test page.  Does the printer print at normal speed?  Is so the black cartridge was the issue and should be replaced.  If not then put the black cartridge back in and remove the color cartridge and print test page.  If the printer now prints normal speed the color cartridge was at fault and needs to be replaced.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • Psc 2210 all-in-one.

    I have an old workhorse, a psc 2210 all-in-one. Can I easily turn the color off and on? Anybody know?   Thanks.

    Does the printhead take a swath and then delay 10-15 seconds before the next swath?  Does the delay also happen when you make a copy?  If so likely one of the cartridges has failed.  Try removing the color cartridge and printing (not copying) a page.  Does the page print at normal speed?  If so the color cartridge is at fault and should be replaced.  If not then remove the black cartridge, put the color cartridge back in and try printing a page.  If the printing now completes in approximately normal time then the black cartridge was at fault and should be replaced.  
    If the failed cartridge is an original (not refilled or reman) HP and not empty you can check the warranty information as shown here.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • HP Officejet and PSC Full Feature Software for HP PSC 1210 All in one printer

    Hello ,
                 I have  HP PSC 1210 All in one printer but i am using windows 7 system.how can i find
                                                                                'HP Officejet and PSC Full Feature Software'
    compatible for windows 7, in hp.com i sould find the above software for windows xp but for windows xp its not working, my printer physical keys are not working so i need software to do everyything from print to scan, copy etc from my windows 7 laptop itself. pls help with sofware for windows 7

    Hi,
    There is not a full feature software Win 7 download available for the HP PSC 1210. The following document includes instructions on how to install the in-OS Win 7 driver with instructions on how to scan:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01796879&cc=us&dlc=en&lc=en&os=4062&product=907...=
    I work for HP.

  • After the latest update printing off the web has moved from readable to font size 6. How to I get back to font size 10 or 12? hp psc 2210 all-in-one?

    When I print coupons or e-mail from my hp psc 2210 all-in-one the font has changed to 6 where before it was size 10 or 12. I have made no changes in my printer settings nor any other changes that I am aware of. This happened after the latest update of Firefox.

    I have a carriage jam on my HP Officejet 5510 which I cannot correct.. I have tried everything I know to do. There are two black pieces that will not spring down when the cartridges travel across. I th en get a carriage jam message.
    Do these pieces need lubricated?
    How can I get t hem to go down when the carriage goes across?
    Thanks for any information or help options
    Karol

  • My 2210 all in one printer keeps giving the message "Remove and check cartridge"

    My 2210 all in one printer keeps giving the message "Remove and check cartridge." Although I go through procedures outlined in manual, message keeps reappearing. Suggestions?

    Hello again!
    Still having problems but here's more info: Checked "Resume" but  Message next to the job says ERROR but that 'Pinter is ready'.
    However, on the PRINT & FAX page in System Preferences it has 'Idle' next to the psc1317 (default) printer.The computer scans the document but wil not print it. With printer off I disconnected the power cable and the USB from the computer then re-connected after 1 minute.  When I turned the printer back on it printed the test sheet but not the document.  I have also unistalled then reinstalled the hp1317 Snow Leopard software and driver and computer says that all software is up to date. Apart from a dodgy connection I have no idea where to go from here!

  • PSC 1510 All in one printer - won't print even black and white when colour cartridge not recognised

    My PSC 1510 All in one printer is flashing the "check printer cartrige icon" and both "Black" and "Colour" icons at the bottom left of the printer.
    It won't print at all, even when I select grayscale (black and white). The help pages tell me that if I remove the colour cartridge the printer will switch to backup mode and I'll still be able to print in black and white (though not copy or scan). But this is not the case, and I can find no way of switching manually to backup mode. The help pages have no useful explanation of backup mode. I've also tried cleaning the cartridge (which I'm pretty sure isn't empty) but that makes no difference.
    Can anyone help? I'd be very grateful.  

    gabri21 wrote: I have a very similar problem with my PSC1510 but only the colour cartridge light is blinking. I am also unable to find any useful information to set up printing in back up mode. Can anyone assist in resolving this problem for us?
    With only one cartridge light blinking I would suspect the cartridge, they do rarely fail (much more often for reman cartridges, see here).  Clean the cartridge contascts as shown here.  If that fails and the cartridge is an original HP then check the warranty date as shown here.  If the cartridge is in warranty return it to your dealer for a warranty replacement.
    The printer will automatically switch to backup mode if the black (or color in some printers) cartridge is removed.  I do not know if this works with the PSC 1510, some all-in-on devices insist on having both cartridges present.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • Paper Jam for HP PSC 1610 All-in-One Printer

    Paper Jam for HP PSC 1610 All-in-One Printer:
    I had a paper jam and cleared the paper from the printer.  Now every time I turn the printer "on" it picks up the top piece of paper from the tray and runs it about ½  to ¾ of the way thru the paper feed, stops, and then displays message "paper jam clear paper and then press OK".  When I do that it simply picks up the next piece of paper off the tray and does the message again.  If I push the OK button on the printer it will simply finish the ejection and then pick up the next paper from the tray, and do the same thing.  I have examined the interior (and exterior) of the printer for paper scraps and  any other obvious sign of trouble (dirty drive wheels, missing rollers, broken springs, etc...) and can not see anything unusual. I can not print a test print because of the paper jam message.  I am running Windows XP and the printer has been working fine for months (until this recent jam).  I did all the steps from the HP fix it site including clean rollers, plug and unplugged,  carriage travel OK and more. Don't know what to do now........Any help would be great!!!!   Thank you!

    Hi my printer psc 1610 hp not picking paper

  • Hp psc 1315 all-in-one printer

    I have installed a hp psc 1315 all in one printer on my new Mac OS X version 10.9.5.
    While I can print without any problems, I don't have access to scan a document from the printer to my computer.
    Can anyone help with this?
    Thank you.

    Hello @annlf 
    Welcome to the HP Community!
    I hope to help you with the scanning concern you have today.
    Unfortunately, you will not be able to scan using HP software with your PSC 1315 (older model), on Mavericks (newer OS X), as there is no Full Feature driver (includes scanning software) available.
    However, you do have some other options to scan. See this link for your options. Scroll down when the guide loads and select "How do I scan with the driver from Apple Software Update?"
    OS X v10.9 Mavericks: Installing and Using the Printer on a Mac
    Have a wonderful Wednesday
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Installing software for my HP psc 1210 all-in-one printer on to my Mac?

    I have downloaded new software and drivers for my all-in-one printer. I am running OS X 10.5.2 on a 20" 2.16 GHz Intel Core 2 Duo. The computer recognises that a printer is present and I can print with no problems. The problem that I'm having is with the scanner function. I don't think that the HP software is registering that there is a printer present. When I go into the HP setup assistant no printer comes up in the selection window. When I go into Printer & Fax via system preferences the HP psc 1210 series comes up as the default printer. I've had this problems before but cannot remember how I rectified it. I'm sure it got something to do with erasing the driver's off the computer and starting over again. Can anyone please help me or point me in the right direction. Thanks

    Hello,
    Here is a link to a support document on hp.com on how to install on OS X Mavericks.
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03967522&tmp_track_link=ot_faqs/top_issues/en_u...
    Let me know if this was usefull by clicking on the Kudos button.
    I work for HP.
    Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
    Click the KUDOS STAR on the left to say “Thanks” for helping!

  • Installing HP PSC 1350 all-in-one printer/scanner

    In the past, I could usually solve the "Offline" or "Not Connected" problems by unplugging my printer for a few minutes, but that no longer works. So, I decided to buy another one. However, just before clicking on the BUY button on Amazon, I decided to try to fix the problem one more time. Part of the "fix" was deleting my printer from the computer and then reinstalling it. This is where I'm now stuck. I deleted it, but I can't reinstall it. I get to the ADD window, but everything is grayed out. So, how do I install my printer? I might add that the HP instructions that I was following (OSX v. 10.9 Mavericks- Installing and using the printer on a Mac) are what got me this far.

    Have you installed the v10.9 Mavericks compatible driver yet >>  Software & driver downloads HP PSC 1350 All-in-One Printer | HP® Support
    After you download the driver, open System Preferences > Printer & Scanners > Print
    Delete the current printer by selecting it then click -  (minus)
    Then click + to add the printer back in.
    That should load the driver for you.

  • HP PSC 1210 All-in-One Printer -- need Software (scanner directory), for windows 7 (64) bit

    hi,
    I am kind of done with this Printer ! lost hope in customer care and support hit with HP ! from Past 10 days searching a software to scan few doc from  my printer 1210 (HP PSC 1210 All-in-One Printer) but i dint find.... i got one from some source (166 Mb) file, but to my surprise its not compatable with Windows 7.  i am totally depressed now.... Please help me to find software for this (scanner document) I have lost the CD lont time back can i download This some where?

    Hi there,
    I understand you're looking for drivers for your PSC 1210 on Windows 7. I will certainly do my best to guide you in this issue.
    At this time there are no HP drivers available for this printer for Windows 7. You can still use the printer with Windows 7, you will just have to use the drivers available within Windows 7. That document will walk you through what you need to do in order to get printing again, and will also show you how to scan with this Windows driver.
    Hope this helps, have a great day!!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

Maybe you are looking for