HP3070 cannot print after new ink replacement

I have replaced the Black (564XL Black) the first time a few weeks ago for my HP3070A and it can print normally.
However when the color ink levels show low levels a few days ago; I replaced them with the new inks 564XL (Y / M / C).
But the printer does not print and come up with Error Message: "Use SETUP ink cartridges".
When I put back the old Setup ink cartridges, the printer also cannot print and came up with the same error mesage.
Now I am stuck here and just cannot use the printer.
What should I do to overcome this problem?

Are you getting the same error message to use setup ink cartridges? Here is a really simple step:
Remove the ink cartridges while the printer is still powered on.
Remove the power cord from the back of the printer and also from the wall and wait one minute (a complete power-drain on the printer removes false errored states, and when you unplug the printer while it is still on, a hard reset can help stop any internal processes that are stuck).
Clean the electrical contacts on the ink cartridges and their associated contact on the printhead while you wait.
Plug the power cord back into the wall first and then plug the other end into the printer so it will power on automatically.
When the printer asks to for the ink cartridges, insert them one at a time and try to print something.
If that doesn't work, don't forget that even though your printer may be out of warranty, the ink cartridges are likely not which still grants you some free support regarding any problems you are having with the new cartridges. US residents can call 1-800-474-6836 or click here for a number in your region.
Let me know if this helps any!
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution!

Similar Messages

My eprinter will not print in proper clolour even after new ink cartridges install cleaned nossles p

my eprinter will not print in proper in colour even after new ink cartridges installed cleaned nossles as new cartridges still not printing properly
This question was solved.
View Solution.

Which printer do you have specifically? HP makes several eprinters and I want to make sure I get the best information for you that I can.
Also, have you tried doing a self test print to see if the issue is hardware related versus being software related?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Cannot print after downloading os7

cannot print after downloading os7

Hey snagger68,
Thanks for the question. The following article outlines steps for troubleshooting AirPrint:
AirPrint Basics
http://support.apple.com/kb/HT4356
If you are unable to print, or if you see the message "No AirPrint Printers Found"
Verify that the printer:
1. Has power and is turned on. If it has power, turn the printer off and then on again to see if that resolves the issue.
2. Is connected to the same Wi-Fi network as the iOS device.
3. Has the latest firmware version installed.
4. Has paper with enough ink or toner installed.
5. Is free of any errors displayed on the printer's control panel.
If necessary, consult the printer documentation or contact the printer vendor for help with the above steps.
Notes:
- AirPrint printers connected to the USB port of the Apple AirPort Base Station or Time Capsules are not supported with AirPrint.
- Some Wi-Fi AirPrint printers can take several minutes to join a Wi-Fi network after being turned on. Ensure that the AirPrint printer is connected to the Wi-Fi network before attempting to print.
Thanks,
Matt M.

Epson Stylus CX9400 - Cannot print in black ink only

I cannot print in black ink only on my CX9400 printer. My OS is Windows 7. I've never had this problem before, and it only happens with pdf documents. Please adivse me how to correct this problem. Thank you.

Dear user BVILLE22,
In 10.1.2, we have intentionally removed the option 'Print color as Black' from the print dialog due to its incorrect behaviour of converting all text to black. The correct one is to print it as Grayscale and for doing so, you can follow the two below mentioned methods:
Method 1:
1. Select your printer and click on its properties button.
2. Search for option 'Print in Grayscale', which is provided at different location for different printers. One I am attaching for reference is under 'Color' tab of printer properties
3. Click ok and then print.
Method 2:
1. Select your printer.
2. click on Advance button.
3.Select Color management section -> 'Working Gray' as color profile.
4. click ok and then print.
Hope this will solve your problem.
Regards
Sonal
Adobe Systems

Ricoh Aficio SP 240DN cannot print after Yosemite installed

Ricoh Aficio SP 240DN cannot print after Yosemite installed

I have this problem too.
I've installed the most recent drivers for these printers and unfortunately it's still not compatible with Yosemite.
I guess all we have to do is wait until Ricoh/Lanier brings out an updated driver for us

MAC OS 10.9 some users cannot print to new Ricoh MP C6502 print job is holding for authentication and cannot figure out why

I have a few IMAC and G5 users who have OS10.9 who cannot print to a new Richoh MP C6502, I downloaded and installed the new PS driver and it works on some systems but I have 3 people that goes right to Hold for Authentication. I tried deleting everything associated with this in keychain access and after I did this it comes up to enter a password and it accepts the network login credentials but still holds the print job. I even tried using guest as login and password as someone suggested but still cannot print any ideas on why?

I apologize for the delay in responding to you. I was on the road all day yesterday.
OK. I switched the printer's Ethernet cable to a Linksys Switch (Model EZX S55W) that's part of this local network. That did not work. I swapped out the cable for one that I know works. Still no change. I switched the printer's Ethernet cable directly to a port on the router. No change. I even swapped cables here, too, but no success.
As I was doing all this, I was wondering: When I select the HP P1606dn printer in the Print and Fax "Add" dialog box, (see the image below) and the Print Using pulldown menu displays "Please select a driver or printer model" and the message "Searching for new drivers" appears under it (with the spinning wheel), why is it that the Ethernet connection to printer is critical to "finding" a new (printer) driver?
Isn't the utility searching through my system and libraries looking for a printer driver app for the printer that I identified/selected in the dialog box?
After all, if the dialog box lists the printer among those to choose from, hasn't the utility already discovered the printer via the Ethernet connection?

Photosmart printer not printing out new ink colours

Hey guys, I own a HP Photosmart b109a and have for a couple of years with no issues.
About 4 days ago we brought some new ink cartridges for the printer as it had run out of colour ink and we were wanting to print out photos since we had heaps of photo paper and had thought it would work out cheaper than going to a store and paying for heaps of prints.
It was the correct ink used but on the first print everything came in shades of blue, no other colour had printed, so after removing the printhead I noticed it had been covered in blue ink as if it had leaked, so I cleaned it as shown online, but then only the black ink would print. I tried printing things with colour only and it would print but come out blank?
No issue with the ink would pop up and cartridges were shown to be full.
After much messing around I finally found how to do a cleaning cycle but only ran one as I didn't want to waste ink and didn't know if it would work.
Eventually the blue and yellow ink started to print and my photos came up as green in colour, but still no Magenta.
After moving from house to house I no longer have the disc to this printer so can't run the HP solution centre as it refuses to find the printer which my Windows 7 has found. I can't even remember how I found the cleaning cycle to try and do it again.
I've tried running many washes and printing heaps of coloured pages but the most I got was magenta appearing as a faded yellow.
So last night I tried to soak the head in hot water overnight as someone insisted it was clogged, which it also looked to be. This morning it was again a lot cleaner but now no colour will print! Only black ink!!
Any help with what can be done!? Getting these photos printed is super important as it's due to a loss of a family member and after paying for new ink that can't be returned, we can't afford to print at a store
Thanks in advance!

No one has a solution? Might just add, an old Calidad cartridge that requires you to carefully remove the chip of an old cartridge then add it to theirs, works perfectly in my printer right now....? the other inks don't want to work though....?

Printer wont print. have new ink. trouble help say it ok but its not ok

I HAVE A HPPHOTO SMART C5180 ALL IN ONE PRINTER. IT JUST STOP PRINTING SO I CHECK THE INK REPLACE IT WITH NEW INK AN NOW IT JUST WONT PRINT I TROUBLE SHOOT IT AN IT SAY ITS OK BUT IT STILL DONT PRINT . I ALLSO REPLACE IT WITH NEW PAPER AN IT STILL DONT WORK

If resetting the que fails try deleting the printer and reinstalling (delete and allow your mac to find it again). This has worked for me in the past when I had trouble with the que.
If that fails you can search the HP website for a OS-X compatible driver for this printer model and try using that instead of the pre-installed driver selected by OS-X.
Good luck. Let us know how it turns out.

Cannot Print After Installing Latest Security Upgrade

Yesterday I downloaded and installed the new Security Upgrade from Apple. Today after restart I cannot print with my Brother HL-1440 printer. I downloaded and reinstalled the printer driver. Still doesn't work. Thank you Apple.
Any suggestions will be appreciated.

Blawrimore,
Have you had a chance to read through the support docs at the Printers website?
I found these two that may pertain somewhat to your problem that you may want to look at:
http://solutions.brother.com/Library/faq/printer/prfaq0797/prfaq0797.html
and
http://solutions.brother.com/Library/faq/printer/prfaq0796/prfaq0796.html
Looks like you are supposed to delete unnecessary printer drivers of other manufacturers and to be sure you "reselect" the printer in Print Center after downloading their drivers.
And, I'm sure you downloaded the correct driver, but certainly wouldn't hurt to double check that it is the correct driver. (that sounds like something "I" would do.....)))
Sorry if these don't help any,
littleshoulders [:-)

Printer cannot print after disabling SNMP

I need to disable SNMP for network security reasons. After doing so from the web configuration page of my P2035N printer, network users cannot print to this printer. It shows as 'offline', even on the web page. We have tried restarting the printer, as well as the print spooler on the server. It is connected via TCP/IP, IPv4.

Working on the assumption that you had an older version of the Canon CAPT driver installed on this Mac before you installed 10.8, I suggest that you open Finder and trash the following files. Note that if you haven't done the reset that Greg has suggested, you will need to open Print & Scan and remove the current LBP6000 printer.
Mac HD > Library > Printers > Canon > CUPSCAPT (trash this entire folder)
Mac HD > Library > LaunchAgents > jp.co.canon.CUPSCAPT.BG.plist
Mac HD > Library > Caches > Canon > CUPSCAPT > CCPD > ccpd.conf
With the above files removed, restart your Mac and then run the CAPT v3.60 installer again. Then add the LBP6000 in Print & Scan and then see if you can print without error.

Cannon LBP6000 printer cannot print after installing os x 10.8.3

After installing os x 10.8.3, the lbp6000 cannot print. I have downloaded and installed the latest driver from cannon. It showed copies are ready to print. But there is no actual printout. The print job just sit in the print que. Any ideas?

Working on the assumption that you had an older version of the Canon CAPT driver installed on this Mac before you installed 10.8, I suggest that you open Finder and trash the following files. Note that if you haven't done the reset that Greg has suggested, you will need to open Print & Scan and remove the current LBP6000 printer.
Mac HD > Library > Printers > Canon > CUPSCAPT (trash this entire folder)
Mac HD > Library > LaunchAgents > jp.co.canon.CUPSCAPT.BG.plist
Mac HD > Library > Caches > Canon > CUPSCAPT > CCPD > ccpd.conf
With the above files removed, restart your Mac and then run the CAPT v3.60 installer again. Then add the LBP6000 in Print & Scan and then see if you can print without error.

Why won't printer acknowledge new ink cartridges

i have windows 7 (64 bit).. HP Officejet 6500 Wireless.. I can print from computer and can copy ok but i have changed all ink cartridges and the printer isn't seeing that it has new ink.. it shows all colors are out?

I think you have the wrong forum.
I'll answer anyway.
Are the new cartridges new original HP cartridges? If not they might not report ink levels correctly.
Please mark the post that solves your problem as "Accepted Solution"
Sometimes it takes several posts back and forth to get to a solution - please be patient.
I am employed by HP

I cannot print after updating my MacBook Pro from OSX Tiger 10.4 to OSX Snow Leapord 10.6. Can anyone help me?

I cannot seem to print after updating my MacBook Pro from OSX Tiger 10.4 to OSX Snow Leapord 10.6. Can anyone help me?

Try re-adding your printer in System Preferences/Print & Fax. Not sure what type of printer you have, but if it was old and relying on an Appletalk connection, Snow Leopard dropped that support.

W2K Cannot Printe after installing MS10-061

On Windows 2000 with Adobe Reader 9.3.2 or 9.3.3 or 9.3.4 after Microsoft security patch MS10-061 we cannot print any PDF to any printer as a user.
Microsoft Security Bulletin MS10-061 - Critical
Vulnerability in Print Spooler Service Could Allow Remote Code Execution (2347290)
Login with local admin privledge and it is able to spool the document and prints successfully.
Login with user privledge adobe gives the following errors.
The Document could not be printed.
Followed by
There where no pages selected to print.
All other applications print successfully Office apps, notepad, etc.
Un-install MS10-061 KB2347290 and printing functionality is restored.
We have tried multiple computer models with multiple printer drivers\models.

Further testing shows that Notepad and word pad are unable to print as well so the issue is not with Adobe Reader the issue
is with the Windows 2000 Print spooler.

Adobe Reader cannot print after installing SAP GUI 6.40 with patch level 25

Hello,
We are in the midst of rolling out sap gui 6.40. Noticed that after installing the gui 6.40 with patch level 25, users cannot print adobe documents. However they can read.
Anyone experienced similar issues? Kindly assist.
Adobe version is 8.
Regards
Sachin

Changes some windows configuration to rectify the above issue.
Thanks
Sachin

HP3070 cannot print after new ink replacement

Similar Messages

Maybe you are looking for