HP8620 connected wirelessly to home network. Using Mac Pro with 10.10.2 Yosemite.

Have wasted 1/2 day trying to get this ALL-IN-ONE to scan to computer or network drive. NOTHING works. Read a previous question to download correct version of Utility for 10.10. Did so, still does not work. Very unhappy.
-Mohsin

Hello @ansarim786 ,
I understand that you are having issues scanning with the Yosemite OS.
I have had success with using the image capture.
Scanning in OS X v10.10 Yosemite Without HP Software
Here are some troubleshooting document you can also try
Scanning with the Full Feature HP Software in OS X v10.10 Yosemite
Mac OS X: Scanning Software Does Not Open or Stops Responding
Aardvark1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!

Similar Messages

Can i use new TC to connect wirelessly to home network and plug my tv into the time capsule for internet connectivity?

My new tv needs to plug into an ethernet port for internet connectivity.
I'm hoping it can plug into my TC however my TC is wirelessly connected to my current home network... how can i get this to work?
TC version A1470 (i think, brand new)
Many thanks.
Ben

If the TC is connected to a wireless network provided by another Apple router, then the TC extends the network by default, and the Ethernet ports are enabled on the TC.
If the TC is connected to a third party network wirelessly, then it must have been setup to "join" the wireless network. When the TC is set up this way, the TC becomes a wireless hard drive and nothing more. The Ethernet ports are not enabled when the TC "joins" a wireless network.
So, a logical first troubleshooting step would be to confirm "how" the TC is currently set up. To do that.....assuming that you are using a current or recent version of AirPort Utility on your Mac.......
Open AirPort Utility
Click on the TC icon, then click Edit in the smaller window
Click the Wireless tab at the top of the window
Check the setting for Network Mode and report on that

Macbook won't connect wirelessly on home network

Hey guys,
I see that a lot of you are having the same issue I am. I have a Macbook that I got the summer of 2008. Up until Thursday, it would connect wirelessly to my E-wire router and network just fine. Then it quit. Later that night, I went up to school for a class, and it connected just fine to the wireless network up there, but will not connect wirelessly to my home network. I have since gotten a new router (Netgear) and reconfigured everything (again), including security and all updates. Airport shows that I am connected to my network, and I can load web pages when I am plugged into the router via ethernet cable (as I am now) but when I try to launch Mozilla or Safari wirelessly, I get the "Server cannot be found" error message.
I am connected to my network, I have tried shutting off Airport and restarting it, as well as quitting my browser and reopening it, and rebooting my Macbook all together. And I also went in and manually entered my IP address, which is what allowed me to connect to the network via ethernet cable in the first place.
Any theories why my Macbook (which is newer) won't connect wirelessly whereas my roommates older Macbook doesn't have any issue connecting wirelessly from right next to me? And I know that it's not an issue of too many people trying to be on the network at once, since it's just the two of us at most, and I'm the only one here right now.
Any thoughts or suggestions would be appreciated.

Is your router a model that supports a/b/g/n? If you turn off N will it work? If your N is setup at 40MHz slots it may not work as well. Can you take your wireless router somewhere else for testing? I assume you might have some issue where you are at with your Mac and that router. When you open Apple Menu/About this Mac/More Info../Network/Airport does it show your network there? From a working machine can you see your Mac from your router web interface? FYI if your router was an Apple product(Airport Express or Airport Extreme/Time Capsule) you could see all your wireless clients via the Airport Utility, even signal strength and connection speed...

Unable to connect wirelessly to home network.

Unable to connect wirelessly to my home network from my MacBook Pro. My Powerbook G4 is connected wirelessly, no problem. However, the MacBook Pro keeps failing. I have tried rebooting both the modem/router and the MBP without success. I have also tried entering in the WEP code several times without success. Need help troubleshooting this. Thank you.

Not a problem. I appreciate whatever assistance you can spare.
I popped an Ethernet cable into the MBP and am downloading the 10.7.5 update. Says it's going to take about an hour. Going to see if that fixes the problem. Seems many Lion users have complained about wireless problems, so it appears I'm not alone.
As far as the other utilities you describe, I can't find anything that fits that description. I have something called AirPort Utility, but when I launch it, the window contains no columns, just a gray window with a globe and a prompt telling me that no AirPort base Stations have been found and that it's searching for one. I see nothing in my Applications or Utilities called Connection Doctor.
Here's hoping the 10.7.5 update remedies the problem. If not, I fear I might have to keep my MBP "tethered" via an Ethernet cable until I can find a fix for this.
Thanks again for your help.

Hello I use Mac pro with OSX 10.9.9 I am trying to download flash player but I keep getting this "Install Adobe Flashplayer" is Damaged and can't be opened anyone got any ideas please

Hello I use a macbook pro with OSX 10.9.5. I am trying to download Flash player but keep getting this message "Install Adobe Flashplayer" is damaged and can't be opened.You should eject the disk image.Any ideas please?

You should make sure you do a complete uninstall of the flash player first and then install the latest FP14 version from this link - Use http://download.macromedia.com/pub/flashplayer/current/support/install_flash_player_osx.dm g
In order to do a complete uninstall - Uninstall Flash Player | Mac OS

[SOLVED] Lenovo W500 fails to connect wirelessly to home network

Hi Arch community. I can't get the built in wireless adapter to work but I can't seem to figure this out. I did drop the laptop a few days ago from about 70cm, but it is able to scan for access points, so I am assuming that the built in wireless adapter still works.
My laptop is a Lenovo W500 and the router is a Netgear Wireless ADSL Firewall Router DG834G.
On the router I configured it to use this security option:
WPA-PSK+WPA2-PSK - If selected, wireless clients may use either WPA or WPA2. This option is sometimes called "Mixed Mode".
$ uname -a
Linux lumjum 3.17.6-1-ARCH #1 SMP PREEMPT Sun Dec 7 23:43:32 UTC 2014 x86_64 GNU/Linux
The relevant lines from lspci -v are:
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Device 20ee
Kernel driver in use: e1000e
Kernel modules: e1000e
03:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300
Subsystem: Intel Corporation Device 1011
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
I followed the guide here https://wiki.archlinux.org/index.php/Be … _wifi-menu
# ip link set wlp3s0 up
# ip link show wlp3s0
3: wlp3s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1492 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether 00:21:6a:51:c0:0e brd ff:ff:ff:ff:ff:ff
# dmesg | grep firmware
[ 13.022655] iwlwifi 0000:03:00.0: loaded firmware version 8.83.5.1 build 33692 op_mode iwldvm
[ 18.315062] psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
# iw dev wlp3s0 scan | grep SSID
SSID: s54msc35m
# wpa_supplicant -i wlp3s0 -c <(wpa_passphrase "s54msc35m" "mypsk")
Successfully initialized wpa_supplicant
wlp3s0: SME: Trying to authenticate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Trying to associate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
wlp3s0: SME: Trying to authenticate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Trying to associate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
wlp3s0: SME: Trying to authenticate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Trying to associate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
wlp3s0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
wlp3s0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="s54msc35m" auth_failures=1 duration=10 reason=WRONG_KEY
wlp3s0: CTRL-EVENT-SSID-REENABLED id=0 ssid="s54msc35m"
wlp3s0: SME: Trying to authenticate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Trying to associate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
wlp3s0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="s54msc35m" auth_failures=2 duration=23 reason=CONN_FAILED
so that didn't work so next I continued to follow the guide and tried:
# echo 'ctrl_interface=DIR=/run/wpa_supplicant' > /etc/wpa_supplicant.conf
# wpa_passphrase "s54msc35m" "mypsk" >> /etc/wpa_supplicant.conf
# ip link set wlp3s0 up
# wpa_supplicant -D nl80211,wext -c /etc/wpa_supplicant.conf -i wlp3s0
Successfully initialized wpa_supplicant
wlp3s0: SME: Trying to authenticate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Trying to associate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
wlp3s0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
wlp3s0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="s54msc35m" auth_failures=1 duration=10 reason=WRONG_KEY
wlp3s0: CTRL-EVENT-SSID-REENABLED id=0 ssid="s54msc35m"
wlp3s0: SME: Trying to authenticate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Trying to associate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
wlp3s0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
wlp3s0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="s54msc35m" auth_failures=2 duration=23 reason=WRONG_KEY
wlp3s0: CTRL-EVENT-SSID-REENABLED id=0 ssid="s54msc35m"
wlp3s0: SME: Trying to authenticate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Trying to associate with 00:18:4d:5d:ef:0a (SSID='s54msc35m' freq=2447 MHz)
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
wlp3s0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
wlp3s0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="s54msc35m" auth_failures=3 duration=46 reason=WRONG_KEY
Both times these two lines show up
wlp3s0: Associated with 00:18:4d:5d:ef:0a
wlp3s0: CTRL-EVENT-DISCONNECTED bssid=00:18:4d:5d:ef:0a reason=3 locally_generated=1
Does this mean it does connect successfully and then I do not understand why it disconnects afterwards?
Many thanks in advance!
Last edited by kso (2015-01-07 09:10:38)

Hi everyone, I got it finally after some more headbashing! It turns out I can't run networkmanager along with wpa_supplicant at the same time. I don't understand why though.
Before I happened to install networkmanager along with network-manager-applet via pacman.
# pacman -S network-manager-applet
# pacman -S networkmanager
# systemctl enable NetworkManager
# systemctl start NetworkManager
So I just stopped it
# systemctl disable NetworkManager
# systemctl stop NetworkManager
and then uninstalled it
# pacman -R networkmanager
# pacman -R network-manager-applet
Then wpa_supplicant works! Thanks.

Using MAC Pro with Lightroom CC as a travel computer.

Would like to put the catalog onto my removable hard drive to move it back onto my desktop. Lightroom gives me error message saying I cannot put catalog on network drive or removable drive. This does not make sense if you are using the laptop as a temporary load and review while traveling. What can I do to get lightroom to allow me to put all the catalog and info on my removable hard drive?

That should work just fine. I have done this many times. Just copy the catalog file and images onto a portable hard drive and you should be able to just double click the catalog to load it. What kind of drive is this? How is it formatted? Make sure it is formatted "Mac OS extended (Journaled)". Often times disks come windows formatted from the store and that might throw your mac off. If you reformat be aware that it will erase everything on there now.

I just moved from a G5 PowerMac to a Mac Pro with one drive running Yosemite and one running Snow Leopard, Do I need Lion to be able to upgrade iPhotos

How can I see my iPhotos from a G5 PowerMac on a MacPro running Yosemite and Snow Leopard? Is Lion a more advance system that Snow Leopard?

The last iPhoto version you can run with Snow Leopard is iPhoto 9.2.4, and Yosemite needs iPhoto 9.6.
Move your photos to your Yosemite partition, if you want to use iPhoto with Photo Streams and other iCloud features.
As you are asking about Lion, you can run iPhoto iPhoto 9.2.3 or iPhoto 9.2.4 both with Lion and SnowLeopard, but there is no iPhoto version, that runs both on Yosemite and Snow Leopard, or Lion and Yosemite.

Can't even connect to my home network.

Title says it all, bought a 64gig iPad wifi today...little did i know tons of users are having wifi problems...my problem doesnt seem to fit the others though. Most of what i've read people can connect for a bit, and after being in sleep mode then it has problems. I can't even connect to my home network. Works fine with my ipod Touch, laptop, etc. I dont have any form of security set up on my router what so ever. I plan on buying a new router soon (for reasons other than this iPad crap.) I'd really like to see some kind of resolution to this problem before i need to do that though.
I tried all that i could out of the trouble shooting stuff. nothing worked. I even tried setting up a static IP for it. What else can be done? i really dont want to have to return it since its such a nice piece of tech.

Umm... one of the questions that's been asked is whether his iPad will connect anywhere else, If it will, the issues is between the iPad and the particular configuration he has at home. If not, the issue is with the iPad.
Since we don't have an answer to that question yet, your inference that anyone is telling him to "phone ahead to every business or hotel he plans on visiting to request that they replace their "clunky old router" " is unjustified and unhelpful.
Please, continuously blaming every ipad wifi issue on the same router that happily works with every other device is getting old. What standards does iPad support that these clunky old routers do not?
Since, as you've said in another post, you're experienced in the ways of the internet, you will know that it's quite common for new kit to have problems connecting to old kit.

HT4199 i resenty up dated my iphone 5, now my phone will not connect to my home network. my kids phones, laptops and macs all connnect to my home network. i have an hotspot router it connects to that but not my homes network, i reset all network setting,

l resently up dated my iphone 5 and now it want connect to my homes network, i have a hotspot router that it connects fine to. all other devisers connect to the home network, l reset all network setting and reentered password (password is correct) and still no go. whats up with this. Thank Mike

It's possible your wi-fi router needs to be reset, or the firmware needs to be updated.
Follow the steps in this article: iOS: Troubleshooting Wi-Fi networks and connections - http://support.apple.com/kb/ts1398

MacBook no longer connects wirelessly to internet after using ethernet

So: here at home I have an airport extreme and a time capsule. The airport extreme connects to the cable modem, and the time capsule extends the wireless network created by the extreme. I was trying to do an initial time machine backup from the MacBook, so I plugged it in with an ethernet cable to speed things up. After using the cable, the MacBook will simply not connect to the internet if I connect wirelessly to the network. When wireless accessing the network, I can see the time capsule's shared drive, etc, but I can't connect through to the wider internet.
Any suggestions?

have you tried doing a power cycle on your modem and airport?

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme..

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme.

This will work.....IF....you also have an Apple AirPort router configured to provide your wireless network.
In other words, you need to have two Apple AirPort routers to extend a wireless network.
When the AirPort Extreme is configured to "extend" the wireless of the "main" AirPort, it will provide more wireless coverage and the Ethernet ports are enabled, so you could connect your Mac Pro to any of the Ethernet ports and use that as a network and Internet connection.

Finding out devices connected to my home network (Time Capsule)

I have a mid-2013 mac pro and I am using time capsule, I suspect that I have some unwanted guests in my home network:-) how can I see devices connected to my home network?

The new TC and the new Mac OS airport utility are totally useless..
You can do it the old fashioned way with netstat scan from terminal or via the network utility (which is also now hidden so search for it).
Grab Fing for your phone or ipad.
https://itunes.apple.com/au/app/fing-network-scanner/id430921107?mt=8

Connecting to existing home network via Airport Express

I had my Macbook Pro connected to our home router which allowed me access to our home network and the internet. On this network we had connected both my MBP and my flatmates PC (which is connected directly to the router via network cable).
Through this configuration i was able to both access the internet AND access files on the PC. I have recently purchased and airport express to eliminate the need for the network cord. Since setting up the AE i have been able to connect to the internet no problem by creating a wireless network and using all the automatic settings, however in the process i have lost my ability to connect to the home network and my flatmates computer. In fact, under "networks" in finder the home network has disappeared. Also in network prefences i am getting a warning saying "The cable for Ethernet is not plugged in".
Is anyone able to tell me what im doing wrong?
thanks ....
Message was edited by: seysearles

The problem is that the AirPort Express (AX) is creating a subnet.
To prevent that, configure the AX to act as a bridge (so that it is NOT sharing a single IP address).

Airport wont connect on my home network when its password protected but..

Airport wont connect to my home network when its password protected. It will connect to my network if i go into my linksys router and set the network to "not password protected". If i put on the security and choose a pass phrase it always says connection failed when i try to connect to the network. anyone got any suggestions on what to try ?
ps and yes i am putting in the password right

Hi Nickerjones
When you enter your password for the Linksys router, is it generating a separate code phrase? By this, I mean if you enter "password", the Linksys converts this to a code that might look something like "ju457re76en7pq" for example. The code is generated based on an algorithm that Linksys uses for their products and should be visible in the set up page. Sorry, I haven't used Linksys for several years so I can't remember all the details.
Other manufacturers use different algorithms for their products, so if you entered "password" on an Apple product, it would likely convert the phrase to a different code, which the Linksys would not recognize. If you can locate the actual code that the Linksys generates when you enter your password and use that same exact code when you enter the password for your wireless on Airport, you may have your problem solved.

HP8620 connected wirelessly to home network. Using Mac Pro with 10.10.2 Yosemite.

Similar Messages

Maybe you are looking for