HPE-510t does not boot with AMD FirePro W5000 (Windows 8.1)

I just purchased an AMD FirePro W5000 (TDP = 75 W) to replace my nVidia Quadro 600 (TDP = 40 W) in my 2011 HPE-510t (i7-2600, 12 GB RAM). Dell U2913WM monitor.
My machine will not start with the new card inserted. I upgraded the stock 300 W power supply to a 450 W Antec VP450F, but that didn't change the startup situation. I tried DisplayPort and Dual-Link DVI-D.
Anyone been able to get the AMD FirePro working in an HP desktop of this generation?
Thanks,
Mike
This question was solved.
View Solution.

Hi Mike,
I am glad that you finally have success. The issue is probably that the PC BIOS level is too low.
The passmark numbers look very good.
BTW -- I had the ASUS P8P67 motherboard and donated it another forum member. It wouldn't support an EVGA UEFI BIOS based graphics card. I ended up replacing the ASUS P8P67 with the ASUS Z87.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Similar Messages

K9AGM3-F does not boot with PCIe 4x device in PCIe 16x slot

K9AGM3-F motherboard does not boot with PCIe 4x Intel PRO/1000 PT dual port network interface card installed into PCIe 16x slot on motherboard. The boot process stops in BIOS screens. The motherboard works flawlessly without this NIC. K9VGM-V + Intel PRO/1000 PT boot successfully. I tried three K9AGM3-F motherboards and two Intel PRO/1000 PT NICs in different combinations, the results are always the same. It appears to be some kind of BIOS problem.

Quote from: Fredrik Åsenius on 09-April-08, 22:52:27
Minor point, probably irrelevant: I said you install the driver f i r s t. Then you put the physical card in.
The driver is completely irrelevant because the driver is a part of operating system, but as I already wrote before the boot process stops long before the OS start.
Quote from: Fredrik Åsenius on 09-April-08, 22:52:27
No stability issues otherwise?
PSU is always good to know.
The PSU is irrelevant too because the same NICs work in the PCIe 1x slot of the same motherboard with the same PSU.

T60 does not boot with Intel T7600G CPU

I replaced my Intel Core Duo T2400 with Intel Core 2 Duo T7600G CPU in ThinkPad T60(1951-CTO) laptop. However, laptop does not boot with Intel Core 2 Duo T7600G CPU. It doesn't even complete the POST: https://db.tt/8UL8FlE0 As seen in the video, I plugged in the power adapter at 0:02 and pressed the power button at 0:06. One can hear a little click made by optical device. If I press the power button again at 0:16, this click does not happen. BIOS version is 2.27. I have reset the BIOS settings by disconnecting the CMOS battery, but this didn't help. Once I replace the T7600G with my old T2400 then I'm able to boot the laptop.
Any ideas what might cause such behavior? Shouldn't there be beep codes in case of CPU issues? What else to try?

TuuS wrote:
600X wrote:
Since you came from a T2400, does your T60 even have a Rev. 3 motherboard? If it does not, then no Core 2 Duo will work, only Core Duo's.
I don't claim to be the top authority on T60 motherboards, but I believe any will use a Core 2 T7600, 7400, 7200 if the firmware is updated.
My own experience mirrors what TuuS has stated. I have yet to see a T60/p from any walk of life with a recent BIOS that will bark at a proper Core 2 Duo CPU.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

HT1349 my iphone 4s does not sync with my laptop using WINDOWS XP

my iphone 4s does not sync with my laptop using WINDOWS XP
As a matter of fact it does not show as deivce under my laptop
Additionally Itunes gets hang when i connect my iphone to the laptop
any reasons- please help

sgnfromek wrote:
As a matter of fact it does not show as deivce under my laptop
Of course not... it's not supposed to. There is no issue with that.
iDevices only show as cameras so that pictures/videos taken with the device can be copied off.
What troubleshooting has been tried to get iTunes to recognize the device?
Different sync cable?
Multiple USB ports?
Reset or restart or the device?
Rebooting the computer?

2960X-48FPS-L does not boot with IOS 15.2-2E

Hello,
i got a bunch of 2960X switches. But some of them do not boot with the new IOS Version. The older 15.0-2 EX do boot.
Does anybody have a clue why this happens? During the Bootprocess it just stops to load:
File "flash:/c2960x-universalk9-mz.152-2.E.bin" uncompressed and installed, entry poin0x3000
executing...
Loading "flash:/c2960x-universalk9-m
Thank you for your help.

On the ones that cannot boot 15.2(2)E, can you break the boot cycle using the "Mode" button?
If the answer is "yes", then try the following:
1. Copy the IOS BIN file from a working switch to a USB flash drive;
2. In ROMmon, force the switch to boot the IOS from your USB flash drive;
3. If it does not work, try a different IOS, like the EX3 for instance. Try the same process, boot the BIN from your USB flash drive.
4. If it works, try a different IOS, like EX3, for instance. Downgrade the IOS from 15.2(2)E to EX3 and see if the switch can boot normally.
This exercise will determine where the fault is coming from: IOS bug or a hardware batch problem.
To determine if you'e got a hardware batch problem, you may need to look at the serial number of the switches working and not working. From left to right, look at the 4th, 5th, 6th and 7th numerals. This will determine the year and month your appliances were made.

Microsof VX 3000 or 6000 Webcam does not work with Lync 2013 under Windows 8.1

Hi,
The problem is that i cannot use the Microsoft VX-3000 or VX-6000 with Lync 2013 under Windows 8.1.
If i go in settings under Video i can see the preview from the webcam just fine, so it works there no problem.
Wenn i try to enable my camera in a conference it does not work, i get an error: Your video cannot be started.
Now, there are no Windows 8.1 drivers for the Webcam so i installed the latest Windows 7 drivers. Because of that this webcam does not work with apps, that is fine i understand the driver problem and the way the new apps work.
But this Webcam works with skype under Windows 8.1 and it works with Lync 2010 client.
The same Webcam works just fine with Lync 2013 under Windows 7.
Is there anything i could do so that i get this Webcam to work with Lync 2013 desktop client under Windows 8.1?
Thanks

Hi,
According to your description, it may be caused by driver.
You can try to install the latest version of Display Driver to fix the display issue.
Since there is no driver for Windows 8.1, I suggest you wait for updating.
You can also post a case on Windows 8 forum, thank you for your understanding:
http://social.technet.microsoft.com/Forums/en-US/home?forum=W8ITProPreRel%2Cw81previtpro&filter=alltypes&sort=lastpostdesc
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

P67A-GD65 does not boot with LSI 9240-8i HBA

Hi All,
When I installed my LSI 9240-8i I was able to boot to the ICH10 Raid as long as the Marvell Raid controller was disabled. Once I updated the LSI card to the latest version of the firmware I cant boot at all. I've cleared the CMOS, I've disabled everything in the BIOS (raid controllers, 1394, NIC, etc). All not no avail.
Thus Far I've tried:
-Booting to OS on the ICH10 RAID gets me into Windows 7 (x64): Resulted in the LSI controller showing, "This device could not start. (Code 10)" under Device Manager.
-Updating Firmware: Resulted in the mobo hanging on POST at code "92".
-Upating BIOS from 1.B to 1.C5 Beta: Resulted in mobo hanging on POST at code "92".
-When I move the card to my Dell Prescision workstation, the LSI RAID controller works like a charm!
Observations:
MSI P67A-GD65 BIOS v. 1.B
-LSI Firmware
20.10.1-0037 (APP-2.120.54-1235)   15-APR-11   - BROKEN
20.10.1-0029 (APP-2.120.24-1181)   - 04-MAR-11 - BROKEN
(Same as above, but I list it anyways)
MSI P67A-GD65 BIOS v. 1.C5
-LSI Firmware
20.10.1-0037 (APP-2.120.54-1235)   15-APR-11   - BROKEN
20.10.1-0029 (APP-2.120.24-1181)   - 04-MAR-11 - BROKEN
MSI PLEASE HELP!
I am running:
Mobo: MSI P67A-GD65 1.C5
CPU: I7 2600k
RAID: LSI 9240-8i
Thanks!

Quote from: NovJoe on 23-May-11, 10:16:19
Looks to me that it is the LSI firmware issue as the card works fine until you updated its firmware.
Do card with the card's vendor.
Hi NovJoe,
Thats just it. It looks like its an MSI BIOS compatability issue all along. Before I upgrade the firmware, the card works in my Dell Precision Workstation, but does not work on the MSI mobo; shows Device could not start (Code 10) error. After I upgrade the Firmware, the MSI mobo will not POST, but the Dell still boots up with the card perfectly.
Its definitely NOT the card. If both the 9240 and 9260 cards work perfectly in other computers then there is something wrong with the MSI mobo or BIOS.
Please help.
Thanks!

24" iMac AlSiO does not boot with iPod video on USB dock

Hello all,
I have already reported this as an issue with Apple.
I noticed that when I turn on my new iMac with the video iPod on the dock connected via USB, I only see the gray screen and the OS does not start. However, once I remove the iPod from the dock, then the Apple logo will show up, and the circular moving tiny line counters will ensue before the login screen appears.
Just wondering if anyone else is running into this problem.

Thanks for the suggestions den.thed and elmac.
I have done the following:
- Selected the Mac OS X on the MacHD as the startup disk and locked that from further changes. Restarting the iMac did not work.
- Verified and repaired permissions. Restarted the iMac and it did not work either.
In addition, I also tried:
- Restoring the video iPod and leaving it without contents. Rebooting the iMac worked.
- Syncing iTunes with the iPod after the restore. The rebooting problem appears again.
It seems like some synced items on the iPod are causing the issue as odd as that sounds.
I did not have this problem with my G5 iMac.
Since there is a workaround, I'll just live with that for now.
Thanks again.

Securing old 10.4 xserve with hot spare - new xserve does not boot with 10.

dear you,
I am in the murky situation of having to secure a single, non redundant productive scenario which is running on one xserve (model identifier 1,1; dual core 3GHz; boot-rom XS11.0080.B00). due to several reasons the server needs to be cloned, so that a separate xserve with a daily cloned boot-device can take over if things go south with the productive one.
unfortunately the newly bought xserve quadcore single 2.26GHz refuses to boot from the image taken from the production machine. tried to downgrade firmware, did not help. new machine crashes during startup (empty grey screen).
anybody knows any help? moving the production machine to 10.5 or newer is NO option.
an option could be two elder xserves I have here additionally. how do I find out which xserve model will boot with an image from the production server?
thank you all for any idea in advance,
thaijay
Message was edited by: thaijay
Sorry, failed to let you know the productive server is running 10.4.11. please let me know which other details I can post/will help us with this issue

This is never going to work via cloning.
The server you're cloning has to be one of the original Intel-based XServes. Each successive revision adds requirements to the OS to the point where they have a minimum OS version. In the case of the latest generation servers, they won't run on anything earlier than 10.5.6 (IIRC). To put it simply - 10.4 doesn't know how to drive the latest generation hardware.
In any case, cloning is rarely a good idea for servers anyway. You would do better to look at the services you're running and look at backup/failover plans for them rather than trying to clone the entire server. Many services such as Open Directory, DNS, MySQL and more have built-in replication systems that are designed to replicate their data across many machines. Other client-facing services such as AFP, web, FTP, etc. can be set to failover (where the second machine takes over the service when the primary machine fails).
Such replication/failover techniques are far more reliable than a daily clone, and they're also faster. Replicated data could be maintained up to the minute, compared to a day old data if you need to boot up the clone.
If you really, really want to go the clone route, then reverse the roles - setup the new machine as the primary server with all the services and clone this machine to create your failover system. 10.5.6 will run the old/original XServe, it's just a matter of updating your services to the newer version.

PC does not boot with Ipod Nano

My configuration:
Shuttle SK83G, Athlon64 3000, Windows XP Pro, Logitech DiNovo wireless desktop.
My problem:
If my Ipod Nano is connected the PC will not boot. The bios screen shows up and then nothing happens. I even can not access the bios. If I remove the ipod the PC will eventually start windows. But in absolute slow motion (I can see how the Windows startup screen fades in step by step).
If I connect my Nano after booting, everything is perfectly fine. Also with my Ipod Mini connected, the PC boots up without a problem.

it's not just a Nano problem, but a USB port problem
That's correct. USB is famous for this. Something in the BIOS (probably) is telling it to try and boot from the nano, but of course it can't find a valid OS there. And the solution is just what you suggested. Don't boot with the nano connected.

K7N2 Delta2-LSR - SATA disk does not boot with IDE disk connected

I have K7N2 Delta2-LSR with SATA 160GB drive and CD burner connected as primary master.
When I'm connecting any IDE hard disk, the mainboard detects it corectly, but I'm not able to boot from SATA drive.
I tried to turn off IDE drive detection in BIOS (set [None] instead of [Auto]) and SATA boots!!! And Windows XP and Linux can see both disks!!!
Is it a BUG in BIOS?
Maciek
K7N2 Delta2-LSR (with latest BIOS Sep 18, 2004)
Athlon XP (Barton) 2800+
SATA drive WD 160GB
GF4MX440
FSB333, DDRAM 512MB/400
PSU 350W, works stable with 2 HDs and CDRW.

Strange my board boots fine from SATA with a PATA HDD connected. XP and Linux will see any disks connected to the motherboard and powered up in your system even if disabled in the bios apart from those connected to a separate raid controller which should be enabled. Both these operating systems address the hardware directly once their drivers are loaded so will ignore the settings you have in the bios. This behaviour is normal and not a bios bug. The main boot disk has of course to be enabled in the bios for the boot loader to operate. The boot priority with the new south bridge is PATA first followed by SATA and XP uses this too. To ensure that XP boots from SATA properly the PATA drive must be disconnected during the install process. You also need to ensure that the SATA disk is the only active partition connected to your system. If the PATA disk has been used to boot an operating system previously there may still be an active partition present on the drive. If that is the case removing the active partition should cure the problem but if the present arrangement works for you then fine.

P35 Neo ram problems. Does not boot with 4 sticks

Greetings!
This thread is little related to: https://forum-en.msi.com/index.php?topic=110095.0
Okey so I bought this rig last friday(will post specs later). 4x 1gb ram sticks, shows up as 3.3gb. Was gona install 64-bit Vista today, but got some problems.
I left my computer on during night just to check if it runs fine. I wake up around 6am, turn power on to my monitor. Screensaver, move mouse, desktop and BOOM: Bluescreen(something about memory). Ok so I shutdown my comp, try to reboot got no signal. Removed 2 ram sticks(A2,B2) and yey it works. I plug them back in and again nothing. I test them 1 by 1 on both of the free slots, no problems detected.
Why won't my P35 Neo boot with 4 gigs of ram? And why did it work for 2days? :P
My guess is that the bios is still not ready yet(using 1.2v).
Specs: OCZ 700W GameXStream, P35 Neo-FI, C2D E6750, 4X PQI 1024Mb DDR800Mhz, Leadtek 8800 Gtx

Quote from: NovJoe on 07-August-07, 10:18:34
If I understand correctly, you are saying that you can install Vista and XP to the system but not able to boot into the OS'es when you have 4GB of RAMs installed?
I would recommend you to test the RAMs with Memtest86.
Yes, I could install Vista and XP just fine. Also at first I could boot them with 4gigs just fine. Now my system won't POST with 4 gigs.
I've tested each one of the ram sticks and they are error free.

MDT - Custom Reference Image does not work with Task Sequence, normal Windows 7 Enterprise Iso media works fine.

Hi,
Our MDT server is acting strange!
I have previously had this system running without problem - i could both capture and deploy computers as is and no changes have been made to mdt.
But my latest capture does not work. When i capture my reference maching in my VM environment it completes without errors and i can import the latest wim file.
When i deploy the tast sequence, it install the custom Wim image, but it ends up with "login" screen as the administrator i have entered for the capture/deploy sequence, but it goes to stop at this point and applications is not installed.
If i change the ISO in the task sequence under Install OS step, to a clean Win7 install media then the capture completes and install applications.
I have also tried to:
Capture reference without password
Capture reference without Windows updates
Customsettings.ini, bootstrap, BDD.log and SMSTS.log to be found here: https://onedrive.live.com/redir?resid=ED5029A20300B814!365&authkey=!AALV1b2ubD0laEE&ithint=folder%2cini
Hope you will be able to assist,
Regards,
Anders

if you have noticed your smsts.log, there is same error multiple -
Executing in non SMS standalone mode. Ignoring send a task execution status message request
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
User did not specify local data drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume A:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume D:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume X:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume Z:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
TSM root drive = TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
We do not find an available volume to store the local data path
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSNextInstructionPointer=1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a TS execution environment variable _SMSTSNextInstructionPointer=1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSInstructionStackString=0
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a TS execution environment variable _SMSTSInstructionStackString=0
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Save the current environment block TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
pszPath[0] != L'\0', HRESULT=80070057 (c:\qfe\nts_sms_fre\sms\framework\core\ccmcore\path.cpp,58)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Filesystem::Path::Add(sEnvPath, EnvDataFileName, sEnvPath), HRESULT=80070057 (e:\nts_sms_fre\sms\framework\tscore\environmentlib.cpp,639)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to save environment to (80070057)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
TS::Environment::SharedEnvironment.saveEnvironment(szPath), HRESULT=80070057 (e:\nts_sms_fre\sms\client\tasksequence\executionengine\executionenv.cxx,842)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to save the current environment block. This is usually caused by a problem with the program. Please check the Microsoft Knowledge Base to determine if this is a known issue or contact Microsoft Support Services for further assistance.
The parameter is incorrect. (Error: 80070057; Source: Windows)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
SaveEnvironment(), HRESULT=80070057 (e:\nts_sms_fre\sms\client\tasksequence\executionengine\executionenv.cxx,420)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to persist execution state. Error 0x(80070057)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to save execution state and environment to local hard disk
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Start executing an instruciton. Instruction name: Gather local only. Instruction pointer: 1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSCurrentActionName=Gather local only
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSNextInstructionPointer=1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
what about the mass storage driver in your boot image, is it updated?
Md.Waseem Please remember to click “Mark as Answer” on the post that helps you. Thank you.

My hp 6500a does not print with my laptop running Windows 8.1 (size mismatch)

I am trying to print from a PC running Windows 8.1 to my HP 6500A all in one printer. It will not print anything except 6x4 photos. If trying to print a document on A4 size, I get the message of size mismatch. I tried it on a second PC (again with Windows 8.1) and it still does not print.
This question was solved.
View Solution.

Are these your settings?
Please mark the post that solves your issue as "Accept as Solution".
If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
I am not a HP employee.

Power switch does not illuminate with the power on , windows 8.1 HP Pavilion 15-B153NR

Power switch does not stay luminated when power is on. Stays on when I press F5. How do I get it to stay on full time when the power is on. I have two of these and the other one does stay lit when ever power is turned on.

Hello , Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel. I read your post about the power light, and wanted to assist you! Check the BIOS version for both machines, and see if they are the same. If different, then try installing the BIOS that the working machine has, on your notebook. You can get the BIOS drivers for your product from this site: Drivers - HP Pavilion TouchSmart 15-b153nr Sleekbook Try checking the Power Management Options for both machines as well. You can use this document to help you, if needed: HP Notebook PCs - Managing Power Options (Windows 8) Please let me know if this information was helpful by clicking the thumbs up below.
Regards!

HPE-510t does not boot with AMD FirePro W5000 (Windows 8.1)

Similar Messages

Maybe you are looking for