HSE/H1 Linking Device Not Communicating

I have a HSE/H1 linking device. It does not communicate with the
NI-FBUS Interface Configuration Utility, version 3.1. I reset it in accordance with the
manual, but it still did not work. This item is less than 1 year old and,
as such, it is covered by the warranty. Can you offer any other trouble
shooting suggestions? If not I would like to return it for repair or
replacement.

I guess your problem is that you can not find any linking device when you tried to add a HSE linking device in the Interface Configuration Utility, right?
Please make sure the LD connects a DHCP server and have a IP address, and I strongly recommend you use a 10Mbps hub(or switch) instead of 100Mbps hub.
If it still doesn't help, please send e-mail to [email protected] for further support.

Similar Messages

What is the default IP address of the HSE/H1 Linking Device?

I am evaluating an NI FBUS-HSE/H1 Linking Device. I am using a PC (not a DHCP server) to communicate to the FBUS-HSE/H1 but the PC cannot detect the device. When not assigned an IP address by a DHCP server, does the FBUS-HSE/H1 have a default IP address? If so, what is it? If not, is there a simple work-around?
Chris

Hi Chris / Sean,
I assume that you mean you got a freebee DHCP "server" & not "client", as most PCs are clients.
Any chance you could direct me to the "freebee" as I have tried a few free ones for this problem but
have had no luck.
Currently I am using an old ADSL modem that has a DHCP server, but it means another box stuck
on the network.
I am also hoping that NI will allow future versions of the LD to boot with a "default" address as most
other LDs now do (something like 10.0.0.1-254 range would be nice).
Sean - is this on the wish list for a future S/W upgrade. Just about everyone that has tried to get
one of these LDs running has come up against this "non-standard" arrangement.
Allen
[email protected]

FBUS-HSE/H1 Linking Device-- unprotected surface mount boards ?

With the HSE Linking device, I noticed that the circuit board opposite the heatsink vent is exposed to the environment.
This circuit board appears to be an uncoated surface mount (fine pitch) board.
Presumably, this would be mounted facing the "ceiling" of the industrial wiring cabinet, since you would want the processor heat to escape from the top.
Unfortunately, this means that any dust and junk in the atmosphere collects on the surface of the SMT board. It wouldn't take much in the
way of fine metal fragments to cause shorts.
So is the board coated ? Is there an "approved" way of covering the vent with an air filter to protect the device ?

Our products meet pollution degree 2 requirements. Adding a filter will not lower pollution degree. You can install the FBUS one of NI's enclosures or an equivalent enclosure to reduce exposure to dust. Enclosure used should have UL or TUV certification (approval) for Ingress Protection (e.g., IP54 min).

Scanning Device not Communicating with the Computer

Can anyone help? I go to launch my Hp Director software to scan a document and an error message appears that says "An error occurred communicating with the scanning device. Please ensure that the scanning device is connected properly and try again." This has happened before but I can't remember the steps performed on the Menu of the scanner. Does anyone know how to get the computer and Laserjet 2840 to communicate?
Thanks

AlmostThere wrote:
If the error message appears on the computer while scanning from a networked product, click this link: http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=au&product=3204785&docname=c00897542. If with USB, click this link: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00040499&cc=au&lc=en&dlc=en&product=3204785
Regards,
AlmostThere
your link @ http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=au&product=3204785&docname=c00897542 doesn't work

Iphone not communicating with computer

iPhone4 not connecting to computer - when i first accessed it it recognised it and made it so i could start using my phone but now after plugging it in again nothing is happening - it doesnt even charge!! however if i turn the phone off and plug it in then it turns itself back on again but again it does not charge or connect to itunes - i have tried services.msc in the run menu and the apple device has started so i am very confused - please help only got my phone 2 days ago!!!xxx

Hi,
Have you tried a Reset on the Phone...
Turn the Phone Off...
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
The Apple logo will Appear and then Disappear...
Turn the Phone On...
If that does not help... See the Information in these Links:
Device Not Recognised
For Mac
http://support.apple.com/kb/ts1591
For PC
http://support.apple.com/kb/TS1538
Device Frozen
http://support.apple.com/kb/ts1445

Linking devices residents in distinct segment via HSE

I would like to make a FBAP link between a H1 device under Linking Device and HSE device with FBUS Configurator.
But, FBUS Configurator seems to disturb such linking.
Now, a Linking Device and a HSE device are working on HSE.
FBUS Configurator shows those two links, and FBAP and Schedule are shown in each links.
Trying to drag&drop the HSE device's FunctionBlock into LinkingDevice's FBAP editor, it disturbs such behaviour.
Can't I make such linking ?

Thank you Chris.
I've read the FF spec again and I've not understood deeply, but I could imagine that H1 device may not be
transparent from HSE device.
Because, the difference of LinkObject mechanism between H1 and HSE seems not to be able to link HSE
and H1 device.
Assuming it is true, nobody can understad why H1 to resident in HSE via LinkingDevice.
Or, only the NI-FBUS Configurator is not capable for such use-case ?

HT5637 How can I keep separate playlists on linked devices so we can both listen to different playlists when not on wifi

How can i keep separate playlists on linked devices so we can both listen to different music when not on a network or wifi?

Hi Nancy,
If you keep the entire iTunes folder as it was and you're still using the same platform, you'll be able to keep all your playlist and metadata.
Nancy2000 wrote:
Just curious why when you have songs and playlilsts on the IPod it doesn't just sync with the computer? It only syncs from the computer to the IPod not visa versus.
Well, iTunes will only transfer content from the computer to your iPod. However, there's some ways to get around this. Read this carefully:
If you have purchased songs from the iTunes Music Store, then those are pretty easy to transfer to your computer. You'll just need to follow [this instructions|http://docs.info.apple.com/article.html?artnum=305465].
All your other songs (for example, those ripped from your CD's), you'll need to use any 3rd party program to transfer them to your iTunes library!
Some can also transfer your playlists, videos, ratings, podcast...
*To use with iPod Touch/iPhone and other iPods:*
[iGadget|http://www.ipodsoft.com/site/pmwiki.php?n=igadget.Homepage] (Mac and Windows)
[iRepo|http://www.purpleghost.com/index.php?q=irepo] (Mac and Windows)
[iPod Access|http://www.findleydesigns.com/ipodaccess/index.html] (Mac and Windows)
*To use only with other iPods:*
[Media Widget|http://www.bootstrapdevelopment.com/showproduct.aspx?t=b#features] (Windows only)
[iDump|http://www.download.com/iDump/3000-2169_4-10407429.html] (Windows only)
[Senuti|http://www.fadingred.org/senuti> (Mac Only)
Hope this helps! If you still have doubts, please reply.
Best Regards,
!http://signatures.mylivesignature.com/54486/122/A57996D55BE7ABB4A67DE686D381A27 4.png!

I have 3 iTunes accounts which I had set up each time I bought a device not realising they all linked up (blonde!!). Can I consolidate them into one account without losing tunes,pics etc??

I have 3 iTunes accounts which I had set up each time I got a new device not realising I should use the same one. Is there a way to consolidate the accounts without losing tunes etc as at the moment my iPad, new iPhone and iPod are all getting different downloads : (

It's impossible to merge two iTunes accounts

Photosmart 7515 connect via USB but not wireless, Device not found on Network

Purchased a 7515 all-in-one, was able to setup wirelessly to MacPro but has lost ability to connect wirelessly. This happened with OS X Lion and nor MountainLion. Have a TimeMachine Airport. Printer connects to network but during setup from MacPro, repeatedly get "Device Not Found on Network" after stepping through wireless installation setup screens. I have reset router, printer, firmware updates, software updates.... at wits end. I have followed the instructions on the below resource page link with no luck. Use WPA-PSK encryption (Automatic AES or TKIP) on network and diagnostics on printer pass.
Please help anyone!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02946597&tmp_task=solveCategory&cc=us&dlc=en&la...

It sounds like the Macs and the printer just aren't communicating.
If you press the network icon on the printer, does it indicate it is connected to the network?
I recommend two additional steps that are not listed in the linked document. The printing system of the Mac may need to be reset as it will clear any software that could be interfering (such as corrupted installations).
Follow the steps as outlined for 10.7 or 10.8 in this document from HP.
The next step is to install the driver package from Apple. This can be found here.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

My lap top says boot device not found please install an operating system on your hard disk

I was on yahoo and page froze. I hit alt/ctrl/delete and nothing happened. I then hit ctrl/esc. I now have a screen saying boot device not found. please install an operating system on your hard disk. hard disk (3FO) What did I do wrong? this is a Compaq presario CQ56-112 NR Notebook Windows 7
This question was solved.
View Solution.

I would suggest going to the following link and going through the listed troubleshooting steps based on your symptoms:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443371&cc=ad&dlc=en&lc=en&jumpid=reg_r1002_us...
I am an HP employee.
Please post rather than sending a Private Message. It's good for the community and I might not be able to get back quickly.- Thank you.
Please click the White Kudos star on the left to say thanks.
Please mark Accept As Solution if this resolves your issue.

T410 broadband device not found

Hello
I am trying to get the built in broadband device work (of course i have purcached the device and installed the hardware aswell as all the required softwares and driver which means the qualcomm gobi 2000 usb composite device 9205 driver and all the thinkvantage sofwares: access connection, active protection system, keyboard customizer utility, mobile broadband connect)
What i'm experiencing is that in the wireless connection status window / mobile broadband tab , under the connection status i see that it has recognised the t-mobile network i should be able to connect to. It says that i have a working connection for minutes with a good quality signal, but when i actually try to connect through the acces connections i get the error message of "connection failed" and i have the two options: "help me fix this" and "close" after i chose the help it goes to the diagnostic tools where the connection status is "not connected" cause "service provider not found" ...then i go to the "sign-up and support" button which leads me to the mobile broadband connect window where i get the following error "no wireless mobile broadband device found" and at the background it also says mobile broadband device not found.
I have tried to reinstall all the drivers and softwares replacing them with the latest ones which didn't have any effect on my problem.
Also i have checked the BIOS settings or my computers wireless settings in-case something is wrong, but everything was set as it should.
At last i have updated the BIOS to the latest one found on your site ( which is 1.32 2010/09/17) but still no change, and i am absolutely sure that the hardware device is installed correctly onto the laptops board.
I'm attaching a capture of the sreen which contains most of the details you need to know, in case i have missed something please let me know.
http://noob.hu/2010/11/15/Capture.JPG
Thank you in advance.
Best regards.
Gergő Csorba
B.Braun Medical Ltd.
Moderator edit: Converted pic >50k to link per the Community Rules. Removed Gergő's mobile number so that he doesn't get an unwanted fan club texting and calling.

Here's the Link for the 2539-AJ6, it does indicate that you have Bluetooth. Dowload and install the latest drivers.
http://support.lenovo.com/en_US/downloads/default.page?

Zen Micro "USB Device Not Recogniz

Hi, I can tell from the forum that this has been discussed quite extensi'vely already but I thought I would check that I have done everything possible.
Basically, I have today received my Zen Micro, installed the software and then connected it to my computer and all I get is USB device not recognized.
I have uninstalled and re-installed the software, tried a different USB cable and socket, formatted and cleaned up the player and still nothing.
There is no other computer for me to test it on. Any suggestions?

Either a new USB cable or more likely a new PCI USB2 card. Chances are the USB card is faulty, but I can't emphasise enough how testing on another PC will clear up where the fault lies. All you need is a PC to test, whether it be a friends, other family member etc.
Also don't forget to search on "communication problem" in the FAQ post, and follow the link that takes you to for lots of troubleshooting advice.

Start-up problem with hp pavilion dv6t-7000‏: "Boot Device Not Found. Hard Disk (3F0)" error

I started getting start-up problems with my hp pavilion dv6t-7000‏. It happens intermittently.
The boot error is:
Boot Device Not Found
   Please install an operating system on your hard disk.
   Hard Disk (3F0)
   F2 System Diagnostics
   For more information, please visit: www.hp.com/go/techcenter/startup
Could a faulty BIOS update cause this problem?
Anyone else who may have experienced a similar problem?
I'd appreciate any help about this problem. Thanks.

Hi
Please find the link given below might help you to fix your issue.
Resolve Boot Device not Found Error Message
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

TS1369 Hello! I have an Ipod Shuffle 2nd Generation and it is not recognized by my Windows 8 based laptop. An error message of 'USB device not recognized' is shown. I have the latest ITunes version installed, and tested the dock in other pc's.

Hello!
I have a problem connecting my Ipod Shuffle 2nd generation to my Windows 8 based laptop. The computer doesn't recognize the Ipod and issues an error message saying 'USB device not recognized'. I tried uninstaling ITunes(latest version) and all other Apple software and reinstaling it back again, checked my USB hubs in the 'Device Manager' section of the Control Panel, you name it.
I could really use some help solving this.
I've turned to the troubleshooting section in Apple Support but it has nothing concerning situations in wich the device isn't even shown in the 'My Computer' folder.
Help a brother out, will you???

Found a solution in another forum http://en.kioskea.net/forum/affich-63733-ipod-not-detected-on-computer (a few posts down).
It was for an IPOD so you can see those details in the link.
Found how to reset a shuffle and inserted it into these instructions - did not have to follow his last steps.
- Turn off computer.
- Plug Shuffle into usb.
- Then you must reset your shuffle
To reset iPod shuffle:
Disconnect iPod shuffle from the computer (if connected).
Move the switch on the iPod shuffle to the OFF position. Note that when iPod shuffle is off, the green stripe by the switch is not visible
Disconnect iPod shuffle from the computer (if connected).
Move the switch on the iPod shuffle to the OFF position. Note that when iPod shuffle is off, the green stripe by the switch is not visible.
- Start computer and it should install the usb driver for the ipod automatically.
- Your i pod will say do not unplug so don't. then open itunes and it will be there.
I did not have to do these thing below – did not get error message and shuffle was displayed in Itunes. / LMc
Just remember to not only eject ipod from itunes but stop usb.
Go to the program icons near the clock and right click the usb icon and "safely remove hardware" will appear and click it.
Stop it and select "apple ipod".

HT200109 Why do all my other Apple devices not care if the movie I rented from iTunes if it was downloaded directly to that device or not, but the stupid Apple TV won't allow you to play rented movies unless you rented it directly from the Apple TV?

Why do all my other Apple devices not care if the movie I rented from iTunes if it was downloaded directly to that device or not, but the stupid Apple TV won't allow you to play rented movies unless you rented it directly from the Apple TV?
Great, so now I have to airplay it by linking my computer to my Apple TV and then the movie has to buffer! So, all that time I spent downloading the HD video has to technically "download" again by buffering. The more I use Apple TV, the more I feel like this item was not created by Apple. I don't even use it for what I originally purchased it for. If I would have known that anytime I wanted to sync a movie from my computer to Apple TV by using airplay that it would have to buffer the movie, I would have never ever ever ever ever purchased this waste of time device. So the video has to technically play all the way through one time first so Apple TV can "remember" the movie to play it back in real time afterwards.
Am I missing something here? Am I doing something wrong that can be fixing my problem? I should have known that the Apple TV had so many things backwards when simple things like when you are using the remote and you reach the bottom of your list, in order to cycle back to the top of your list you have then press the directional buton back the other way rather than most modern day devices that will automatically cycle you back to the top or to the other side when you reached the bottom or end but keep on pressing the button. That **** annoys me when I am doing a search for a movie and have to type the name in manually and have to cycle back and forth to the letters. It makes me feel like I am using a rotary phone or something!

I was told by someone to try and purchase something directly from my Apple TV and that will help authorize my Apple TV. So I picked something that was free and it downloaded.
Then I went back to the Movie that would not work and it played just fine.
So it seemed to work. I will have to try it on other movies and TV shows later.

HSE/H1 Linking Device Not Communicating

Similar Messages

Maybe you are looking for