HT1175 how do you set the airport time capsule as the primary base station rather than as a network client?

how do you set the airport time capsule as the primary base station rather than as a network client?

The Time Capsule needs to connect to a simple modem......not a modem/router or gateway type of device that is often furnished by Internet Service Providers.
So, the first logical question here would be......
What is the make and model number of the device that you call your "modem"?

Similar Messages

  • Does the airport time capsule eliminate the need for my cisco linksys wireless router?

    does the airport time capsule eliminate the need for my cisco linksys wireless router?

    I understand that your network now looks like this:
    Modem > Security Router > Cisco/Linksys router > Devices
    If you do not want to use the Cisco/Linksys router and use a Time Capsule instead, then your network would look like this:
    Modem > Security Router > Time Capsule > Devices

  • How to set up AirPort + Time Capsule On the Same Network but make it so only i use it?

    Ok so i am planning on getting the AirPort + Time Capsule in a few weeks, and i have seen many peole talk about how there is a right way and wrong way to set it up because apperently the bad way makes it run slow? Well i have two questions, one is how do i set it up the right way to use it to the full potential to use the new beamforming feature? And my second question which is kind of a problem is that I have internet already but my other brothers use it and i told them about pitching in buy it and they dont want to because they think its pointlesss, so what i want to know is if I can connect it to my existing wi-fi but at the same time like create a diffrent network so that only i can use it? (ex. have my wifi, 2WIRE123 for example, and then some how connect the ethernet cable to the airport + time caplsule and create a new network like 2WIRE124 so they would both basiaclly be using the same internet connection but separated to 2 diffrent networks?) Thank You.

    so what i want to know is if I can connect it to my existing wi-fi but at the same time like create a diffrent network so that only i can use it?
    Sorry, but no.
    If you can connect the AirPort to the 2Wire router using a permanent wired Ethernet connection, then you can configure the AirPort to create a new wireless network with its own wireless network name and password.

  • How can I set up my time capsule as the primary base station with a centurylink router? I'm trying to extend my coverage, increase signal strength, and be able to connect a printer.

    I recently moved and now I'm trying to set up my Time Capsule as the primary base station or router with an existing network that has a Centurylink modem/router. The TC still has the settings for my old network. I also have backups on it. I have the data backed up to another HD so it's not an issue to return it to factory settings if doing so deletes the back ups. Do I need to restore it to the factory settings to set it up? Also, what settings would I select on the TC (and the Centurylink modem/router) in order for the TC to serve as the router, instead of the Centurylink router? I want to be able to use the TC to back up my Mac's, print wirelessly, and improve overall performance. I tried setting the TC up and ended with 2 different networks. Can anyone please help me with this?

    The TC has to plug into the existing modem router by ethernet.. you cannot use wireless.
    You have a choice of which is router.. only if Centurylink agree to bridge their modem router.. this has to be done by the ISP and often they do not allow it.
    Is your broadband cable or adsl or fibre or ???
    If it is cable and you are allowed to purchase your own cable modem pick a pure modem version with no router in it.. plug the TC into it by ethernet.
    Setup the TC in DHCP and NAT mode.. (depending on broadband type).
    You must reset the TC to factory to do the setup.. no files are lost at all.
    Here is my current recommended setup.. with Yosemite life has become harder than ever.
    Factory reset universal
    Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
    N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
    Setup the TC again.
    ie Start from a factory reset. No files are lost on the hard disk doing this.
    Then redo the setup from the computer with Yosemite.
    1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
    eg TCgen5 and TCwifi for basestation and wireless respectively.
    Even better if the issue is more wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round.
    2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
    3. Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place when Yosemite cannot remember its own name for 5 min after a reboot makes for poor networking. If the TC is main router it will not be an issue.
    4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric.. but this change will mess up your TM backup.. so be prepared to do a new full backup. Sorry.. keep this one for second round if you want to avoid a new backup.
    5. Mount the TC disk in the computer manually.
    In Finder, Go, Connect to server from the top menu,
    Type in SMB://192.168.0.254 (or whatever the TC ip is which you have now made static. As a router by default it is 10.0.1.1 and I encourage people to stick with that unless you know what you are doing).
    You can use name.. SMB://TCgen5.local where you replace TCgen5 with your TC name.. local is the default domain of the TC and doesn't change.
    However names are not so easy as IP address.. nor as reliable. At least not in Yosemite they aren't. The domain can also be an issue if you are not plugged or wireless directly to the TC.
    6. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
    There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
    You might need to do some more work on the laptop itself. eg Reset the PRAM.. has helped some people. Clean install of the OS is also helpful if you upgrade installed.
    Tell us how you go.
    Someone posted a solution.. See this thread.
    Macbook can't find Time Capsule anymore
    Start from the bottom and work up.. I have a list of good network practice changes but I have avoided Yosemites bug heaven.
    This user has had success and a few others as well.
    RáNdÓm GéÉzÁ
    Here is why Yosemite has fundamental issues.
    http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

  • Setting up Airport Time Capsule for the first time

    Following directions, when open the Airport Utility, there is no continue button to proceed...
    Where is the continue button to move on to create a new wireless network?

    Sometimes the utility has issues..
    It is easier IMHO to do it manually.
    See here for manual setup of the TC.
    Airport Utility shows "unexpected error - please try again" when connecting to Time Capsule
    Repeated pretty much here.
    Airtport Utility can't find Airport Time Capsule on either of my 2009 Macs
    Tell me where you run into trouble if it still happens.

  • How do you set up multiple time capsules in my home?

    I have one time capsule for my information and my roommate has another.  They are in the same room.  How do I set them up so our information doesn't get confused?

    I doubt you will have confusion.. if they have different names.. then network wise they will be fine.
    ie You set up your TC named TCTom / TCJulia.. and the other person has his/her TCHarry / TCHarriet.. then clearly they are different..
    You can have wireless issues though. If they connect via the same network.. then use ethernet and turn off wireless. Or make a pact and share wireless on one. ie the TC can be plugged into each other.. but wireless only working on one.. they will both be equally accessible and work equally well.

  • HT1178 I just bought an Airport Time Capsule. I already have a AirportExtreme for my wireless network for my home. Which would be better; connect the time capsule up to the extreme or use it as the primary base station?

    Is it better to connect my Time Capsule up to my existing wireless network or use the Airport Time Capsule as the base unit and start over again by creating a new network?

    There is no end of answers to this..
    But if you want AC wireless.. assuming you bought a new TC.. and the Extreme is the older N model.. then simply make sure the TC is as close as possible to where wireless AC client will be used.. and connect it back to the main router whichever that is, by ethernet.
    If both are AC then it will make no difference.
    As long as you can connect them both by ethernet and not use wireless extend.. it won't make much difference.
    The worst case is where you use wireless extend and expect high speed but totally lose it because of your bridge link.. if that is the case you wasted your money and you can return the TC and buy a hard disk and plug it into the AE.

  • How can i use the airport time capsule as a external hard drive?

    how can i use the airport time capsule as a external hard drive?

    Why do you recommend not place things like iTunes libraries or photo libraries on the drive? It was what I am looking for...
    I suggest that you ask the experts over in the iPhoto Support Community about their opinions on placing an iPhoto or Aperture library on the Time Capsule....even if you plan to use a wired connection for your Mac and the Time Capsule.
    But, if Terrence Devlin answers, be prepared for a lecture about why you should not ever do this.
    If you place the iTunes library on the Time Capsule, be prepared for iTunes to give you messages about not being able to find the library.
    In addtion, LaPastenague has the answer for you in a nutshell......corruption problems.
    Bottom line....the Time Capsule is for your backups.....not "everyday" files and especially not libraries.

  • How do I set up my time capsule to operate as a wireless hub when it is not plugged into the internet?  I want to be able to share wirelessly the information on the time capsule. thanks!

    How do I set up my time capsule to operate as a wireless hub when it is not plugged into the internet?  I want to be able to share wirelessly the information on the time capsule. thanks!

    I would prefer to answer in your post. as I have tried on two occasions to help.. so far this is the first time I can see you stated  you are using Lion.
    1. Did you download and install the 5.6 utility..?
    I said to do it.. you never said yes.. I did that.
    Please do it. .. you will get no place before you do.
    2. Did you bridge the TC.. ?
    If so it will work perfectly.. please post a screen shot of the summary page from the 5.6 utility. If something is wrong I can work it out from there.
    3. Or ring apple support and get them to walk you through the setup.. there should be phone support for the first week or two.

  • HT3275 How do I correct this problem: "Time Machine couldn't complete the backup to "Robert's Airport Time Capsule."  The backup disk image "/Volumes/Data/Robert's iMac.sparsebundle" is already in use.

    How do I correct the following problem?
    "Time Machine couldn't complete the backup to "Robert's Airport Time Capsule".
    The backup disk image "/Volumes/Data/Robert's iMac.sparsebundle" is already in use.

    xor. wrote:
    I switched off the TM  for 10 seconds and my laptop still complains about the backup image ...  is in use.
    Some ideas?
    There is some more details here.
    C12 http://pondini.org/TM/Troubleshooting.html
    Tell us more if you cannot get it working.

  • How does one sync the new time capsule with the old airport extreme and airport express in order to extend range?

    How does one sync the new time capsule with the old airport extreme and airport express in order to extend range?

    Thanks for the additional information.
    Unfortunately, the AirPort Utility application in the Lion and Mountain Lion operating systems, which is used to configure the new Time Capsule does not support the older versions of the products that you have.
    Even if it did, there are no settings on the older AirPorts to "Extend a wireless network", so they are not compatible with the new Time Capsule if you intend to extend the network only using wireless connections.
    If you have the ability to connect each AirPort to the Time Capsule using a permanent wired Ethernet cable connection, it might be possible to use a complicated workaround to install an older version of AirPort Utility to configure the older AirPorts to work with the new Time Capsule.
    If you have another Mac there that is using the Leopard or Snow Leoapard operating system, things would likely be simpler. I have not done this type of procedure to mix a new Time Capsule with older AirPorts, so I would not be able to say whether this would work or not.

  • How do you set a default Home Page in the Safari Applet?

    How do you set a default Home Page in the Safari Applet?

    How do you set a default Home Page in the Safari Applet?

  • HT1145 I am setting up my Time Capsule for the first time, all of my connections are right but, AirPort is not recognizing the Time Capsule or my network!

    I am setting up my Time Capsule for the first time, all of my connectiions are correct but, AirPort Utility is not recognizing my Time Capsule or my network?

    Try connecting your iMac to the Time Capsule with an Ethernet cable to see if that allows AirPort Utility to "see" it.

  • XBOX ONE. I have the xbox one and the airport time capsule and cant connect to most xbox live games and zero parties. I have 0 experience in all this but somehow was able to change NAT to open but still wont connect. HELLLPPPP

    Okay folks, I need your help out there.
    So the nerdy side of me went and picked up the XBOX ONE on release day. Its awesome by the way, BUT..... I cant seem to connect to most xbox live games and absolutely ZERO parties. At first I just thought it was something to do with the xbox itself and would eventually fix itself, but i was wrong. After looking into it on microsoft, i found out that it had to do with my NAT settings on the airport itself. I guess apple and xbox are not compatiable for xbox live and it makes it difficult to have an open NAT setting and is a huge PAIN.
    I was able to pinpoint one that the airport time capsule was blocking the IPV6 something or another. Anyways, I unblocked that, and reset the modem and time capsule and jumped on the xbox and now have open NAT settings but still cant connect to multi-player.
    Upon further searching, i was told to uncheck the UPNP on my time capsule as well, but have no idea how to find that.
    I know it seems confusing, but thats the best i can describe it.
    tthanks all

    Be a long long time before I see an Xbox One.. but whoever told you to uncheck the upnp in the TC.. tell them their dreamin' .. upnp is not support by Apple in any computer or router, never has been.. Apple deliberately wrote their own version called NAT-PMP to do the same thing.. dynamically open ports at the request of an application or client computer.
    So there is nothing like that to uncheck.. and as a matter of interest.. there no box to check or uncheck for NAT-PMP either.. since apple do not believe in end user adjustment of settings.. they simply do not exist.
    You will have to manually forward all ports required by the Xbox via the TC. For multi-player games you probably need to open more ports than the standard to allow just xbox live. You will need to check the ports required and open them.
    OR
    Buy a standard vista UPNP compatible router.. and use that.. and simply put the TC in bridge in the network.
    I have not seen posts yet about xbox one.. but there are plenty about xbox and ps3 and the fact that Apple really doesn't give a hoot about games consoles.
    This is a good basic post for older xbox.
    https://discussions.apple.com/thread/5385065?tstart=0

  • I changed my ISP, how I can Setting up my Time Capsule ?

    Recently, I changed my ISP, how I can Setting up my Time Capsule again?

    Hello. I jus tbought mine and will be setting up shortly. So I am only guessing here, based on how my airport extreme base station acted when I switched once. When you connect the ethernet to it, it should simply find the signal,a nd prompt you for the password information that you set up with the new ISP.
    If not, please report back how it goes..

Maybe you are looking for

  • ITunes error while trying to open

    After installing iTunes on this computer I have received the same error multiple times while trying to open it. The error is simply "iTunes has encountered a problem and needs to close. We are sorry for the inconvenience" and then gives me the things

  • In copmlete items in catalogue, only complete items were transfered

    Hi SRM Gurus, We are using SRM 1.0 with Requisite catalogue. We are able to connect, shop and add to their shopping cart. However, after they click the Transfer button, the items do not transfer into their system. The shop displays an error "Incomple

  • HT201209 I bought €40 worth of iTunes and it says I have to use the French storefront what do I do and will it work?

    I bought €40 worth of ITunes cards from France but when I go to redeem it, it says that I have to use the French storefront I don't know what to do and will it change into pounds if I change it over to the French storefront so can you please help me

  • Hyperion Shared Services jar file css-9_3_1.jar in different locations

    Dear All, We found that HSS jar file, css-9_3_1.jar, can be found in many different locations as shown below. Doing a Unix diff, they are not all the same. I just wondering why was that. Currently, there seems no problem. But, I just worry that there

  • Issue with a Procedure

    declare -- Local variables here i integer; begin -- new_pack.set_value(false); new_pack.get_value; end; In the above code, The procedure returns the last passed set value  even when i comment the setvalue procedure and retrieve the value from get _va