HT1212 my ipad is disabled but the disabled word is not in red,what can i do/
hello everyone can u help me with my problem?
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup).
If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.
You may have to force iPad/iPod into Recovery Mode
http://support.apple.com/kb/ht4097
Similar Messages
-
Ipad is disabled and forgotten pin number. What can I do??
Ipad is disabled and forgotten pin number. What can I do??
You have to restore the device within iTunes. You want to use the same computer that you always sync with so that you can restore your iTunes content. You can restore with any other computer, but you will lose everything on the iPad.
Instructions can be found here.
http://support.apple.com/kb/ht1212
You will probably need to restore using Recovery Mode. You can read about it here.
http://support.apple.com/kb/ht4097
Or you can follow these Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad. -
I want to restore my new ipad to my old ipads back up, but the back up is not listed in the drop down menu.
OK, report back once it is done even if it works so that others with similar problems can find solutions.
-
Hi, I forgot the password of my iphone4s I tried more than ten times and it lock me out with a message to connect the iPhone with itunes on the screen but the itunes doesn't recognise it. What can I do?
Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device
1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
2. iOS- Forgotten passcode or device disabled after entering wrong passcode
3. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
4. iOS- Understanding passcodes
5. What to Do If You've Forgotten Your iPhone's Passcode
6. How to Recover Forgotten iPhone Restrictions Passcode | The iPhone and iPad
7. Restoring iPod touch after forgotten passcode
8. RecBoot: Easy Way to Put iPhone into Recovery Mode - if all else fails.
Forgotten Restrictions Passcode Help
1. How to Recover Forgotten iPhone, iPad Restrictions Passcode
If this method does not work, then you will need to fully Restore your
device as New
Also, see iTunes- Restoring iOS software. -
I am not able to turn off voice over. I have tried to do settings -> General -> Accessibility -> VoiceOver and then triple clicked it but the VoiceOver won't turn off. What can I do? I have even tried to reset the machine keeping the data, no use.
A few people have reported problems with the hand gestures since IOS 8. It's not normal, I have don't have the problem on my iPad 4. I doubt it's a major problem but if it happens regularly I'd have it checked out by the Genius bar at the Apple Store.
-
I have windows 7 64 bit but the new itunes will not install because it can't find itunes64.msi. I have searched evertwhere on my pc. In addition, I can't uninstall the itunes and reinstall for the same reason. I can't upgrade for my icloud account.
Try the following steps:
1. Go to Microsoft website to fix install and Unistall problems. Click "Run now" from Fix it to remove all iTunes & related installer files:
http://support.microsoft.com/mats/Program_Install_and_Uninstall
Be aware that Windows Installer CleanUp Utility will not remove the actual program from your computer. However, it will remove the installation files so that you can start the installation, upgrade, or uninstall over.
2. You should remove all instances of iTunes and the rest of the components listed below:
it may be necessary to remove all traces of iTunes, QuickTime, and related software components from your computer before reinstalling iTunes.
Use the Control Panel to uninstall iTunes and related software components in the following order:
iTunes
QuickTime
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support (iTunes 9 or later)
Follow the instructions from Apple article listed here: http://support.apple.com/kb/HT1923 to remove all components
3. Reboot your computer. Next, download iTunes from here:http://www.apple.com/itunes/download/ and install from scratch -
When you install Premiere Pro as the admin on an iMac the audio functionalities work well but a second admin account on the same machine does not work. What can I do to fix this?
It is a bad idea to hack computer passwords when you don't own the computer
Good luck with the school and the parents. -
I want to buy the special complete subscribtion for 36,89 € a month. The requirement to have at least CS3. I own CS5.5 but they say I am not authorised. What can I do?
contact adobe support, http://helpx.adobe.com/x-productkb/global/service-ccm.html
-
I have installed facebook on my iphone4 but the app doesnt come up on screen, what can i do?
Have you restarted your phone?
If so, try a reset. Press and hold the home & sleep/wake buttons until the screen goes blank, ignoring the power off slider if it comes up.
Check for the app again after the phone starts back up.
~Lyssa -
i need help i drop my cell in the water and it show me no sim i buy a new sim. but the seim it show me no sim . what can i do?
aredina, It's disheartening to learn that your phone was dropped. When a device is exposed to water, it's very common to receive error messages such as "No SIM". It sounds like the SIM card slot or copper readers may be damaged. Have you covered your phone with insurance http://vz.to/o9N7Nb? If so you can file a claim, here http://bit.ly/07CrqPK. We're happy to examine your phone for you at any of our local stores http://bit.ly/3SdsA , as well.
TanishaS1_VZW
Follow us on Twitter @VZWSupport -
my macbook pro was first installed with leopard and bootcamp 3.2 under windows 7. After update to lion it is no more possible to update bootcamp to 3.3. or 4.0. The report: The installation source ist not correct. What can i do?
auf Deutsch:
Auf meinem Macbook pro war Leopard und bootcamp 3.2 unter windows 7 installiert. Nach dem update auf lion kann bootcamp nicht mehr upgedatet werden. Weder auf 3.3. noch auf 4.0. Folgende Fehlermeldung kommt: Boot camp Dienste: Das installierte Produkt stimmt nicht mit der Installationsquelle überein. ... Was kann ich tun?It means what it says. The "computer person" formatted it wrongly/ unsuitably. it needs to be formatted again.
Error "Case-sensitive drives not supported" or similar install error | Mac OS
Mylenium -
I keep getting an error, and the Java Update will not install. What can I do?
Never mind. I kept trying, and finally when I opened "About This Mac" and clicked the software update from there (as opposed to the "Software Update" just below), the Java update finally worked.
-
HT1212 my ipad is disabled and will not accept my passcode
following an update my ipad is disabled and will not accept my passcode
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary. -
WWhen I press the email of a contact, the new message box appears with the address but the send icon is not highlighted. Even after typing a message, I can not send it. This is on both I Phone 5 and I Pad Air 2. this just started and not sure what I did. Help please?
Read this thread, it's a bug that many are experiencing:
Cannot send emails from contacts -
I recieved an email from itunes stating that someone was trying to use my apple acct. so I was going to email apple but noticed that the email address was not apples. What should I do if anything? Thanks
dont give your password. in fact change your apple id password. treat the email as spam/phishing
Peace, Clyde
Maybe you are looking for
-
Extraction using infoset query.
Hi, I have an extractor in R/3 which is using infoset for extraction. The infoset contains some logic for extraction. I want to debugg the infoset. As the infoset is not attached to a query how can i debugg the code written in infoset. Thanks & Rega
-
Why does Windows 7 say that PRS-T2 is NOT COMPATIBLE with Windows 7 and not install it?
I have downloaded and installed the Reader for PC and System updates that came out in March of this year (I believe). But since I had to do a clean reinstall of Windows 7 several months ago, I cannot install the reader. Can anyone help me?
-
AD to OID integration problems bootstraping.
I am trying to integrated OID to AD and am having problems bootstrapping. The following is the bootstrap command and resultls: dipassistant bootstrap -port 389 -profile ActiveChgImp -dn cn=orcladmin -passwd password Bootstrapping in progress..... Boo
-
How come the apps that I downloaded will not sync onto my Ipod touch?
Well recently I was really wanted to have apps on my ipod touch. (Its iOS is 5.1.1) When I try to sync on an app to my ipod touch it doesn't sync in the apps!! What can I do!?!? ._.
-
LSMW to Load Cert Profiles (QC01) & handling Blank Fields
I have been trying to create an LSMW to Create New Certificate Profiles (Transaction QC01). As their doesn't seem to be any other way of doing it I have been creating the LSMW with Standard Batch Input Recording. The first problem I had was that ea