HT1222 When playing something recoded on cam no sound from mic.

When I go to play a video I recorded the sound that should be coming from the mic dosent yet other sounds will play, please help

Hello supercow74,
After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning audio issues:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Keep in mind that the article it for iPhones, but the same rules apply for iPads.
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

Similar Messages

HT4623 I have just finished the upgradation to an iOS 6.1.3 and have lost sound in Music and Videos. I am using an iPhone 4S. My iPhone doesn't produce sound when playing Youtube or local camera videos. However ringtones and notifications sound works fine

I have just finished the upgradation to an iOS 6.1.3 and have lost sound in Music and Videos. I am using an iPhone 4S. My iPhone doesn't produce sound when playing Youtube or local camera videos. However ringtones and notifications sound works fine.It is quite strange as well. Have you encountered this issue before?If yes then what's the solution?

I had major issues with the iPhone 4s battery, however it’s resolved.
The tech who set the phone up at the Apple store did so with little training.
if you have a mobile me account. First go and move all your data to the cloud by going on your computer and logging in at me.com/move. The cloud has replaced mobile me, so there is no need for those two accounts
Also make sure that for any of your email accounts you set them up to fetch, not push. My tech person set them all to have the email servers push data to the phone. The new iphone4s antenna is extremely strong so it will continually try to access stuff that is pushed–***** a lot of battery life doing this. It makes it worse if you have exchange 2010 accounts. Something about changes made to exchange really suck battery life from devices that access such accounts.
turning of locator and the push notifications from facebook--they have a lot!

RMBP - Fans run at 5500rpm when downloading something at speed of 4MB/S from the net

RMBP - Fans run at 5500rpm when downloading something at speed of 4MB/S from the net
when i download something from the internet and the speed of the download is 4mb/s the fans start turning at the top speed and stays at that rate until the download is finshed .... it is very disturbing
is anyone experincing this ? or its only my poor RMBP??
p.s not only 4MB/S but also 5MB/S or 6MB/S or more ...
using mountion lion

ok if no one want to answer at least tell me if this could break my mac

The contact list I get when emailing a photo inside camera is different from "contacts" or the one in my email account and it has incorrect email addresses in it. how do I change it or get rid of it.

How do I edit the contacts list that comes up when emailing a photo in the camera ap.

In the future, you might get better results if you post your own thread rather than responding to one that is this old (a year and a half).
When the contact that is not in your contact lists shows up, tap teh arrow beside it inteh list. The information pop up will give you the opportunity to remove it from the "Recents" list (or add it, if you choose).

All my videos downloaded from Itunes will no longer play. I can hear the sound from them however, the screen goes bright green and begins to flash. Can anyone help with this problem.

Green screen on videos. I have a MAC, please help.

Morning brandyfields05,
Thanks for using Apple Support Communities.
For No video or flickering, take a look at this article:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573#1
Reset the system
You can reset the Mac's parameter RAM and SMC.
Reset the resolution
Start by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
          1.          Start up in Safe Mode.
          2.          From the Apple () menu, choose System Preferences.
          3.          Choose Displays from the View menu to open the preferences pane.
          4.          Select any resolution and refresh rate that your display supports.
          5.          Restart your computer.
Best of luck,
Mario

Only the front 2 speakers working with a 5.1 set up when playing mus

I have a xtreme gamer card, with the 2.5.0006 driver installed which worked fine up until recently. Recently only the front 2 speakers play when playing music. All 5 produce sound when tested from either the creative console or windows sound manager. So all 5 are correctly connected, yet when music is played only the front lef and front right speakers are used.
I'm using vista 32-bit.
If there is already a thread on this particular problem (all 5 work on a test and it's a 5. not 6. system) then I apologise but would still like a link. Thank you for your advice.

You should email Creative support and report the problem.
CMSS-3D has problems with the latest beta on Vista x64, but you're running 32-bit Vista on their release drivers, which is supposed to work fine.
If you get a message saying 'would you like to disable audio enhancements?' and you click 'yes', you are disabling CMSS-3D from working, which is the function that transforms normal stereo music into multi-speaker music.
You can try re-enabling it manually:
Open Sound Control Panel.
Select your output device (e.g., Speakers.)
Hit the Properties button at the bottom of the Sound Control Panel.
Select the Sound Blaster tab.
Uncheck the 'Disable Sound Blaster enhancements.'
Hit OK, and OK.
Go into the Creative Audio console, make sure you're in Entertainment mode, and go into the CMSS-3D panel, set your settings here as you like it.
Pray.
Test.
That may not work, especially if the driver / operating system was reporting problems with CMSS-3D in the first place; you may end up getting garbled sound or an error message again.
Send your details to Creative so they can try to work on it, because it sounds like driver issues to me.

No sound when playing movies

Need trouble shooting advice. When playing movies I'm getting no sound / playback freezes. Tried uninstall and downloaded newest version still no improvement. Music playlists work fine.

Hello nsidout,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Troubleshooting iTunes for Windows Vista or Windows 7 video playback performance issues
http://support.apple.com/kb/TS1718
Best of luck,
Mario

When i try to upload a .mts file from my Sony camera to Premiere Pro CC it refuses to play the audio! Ofcourse i could convert every single clip but it takes tons of time. How can i make Pr play audio track properly?

When i try to upload a .mts file from my Sony camera to Premiere Pro CC it refuses to play the audio! Ofcourse i could convert every single clip but it takes tons of time. How can i make Pr play audio track properly?

Does it not play at all or cannot you get the audio in the timeline?
Did you copy the entire card to the hdd and then imported the file via the Media Browser?
Did you source patch the audio tracks?

Cannot found url error when i try to play my camera recorded video from my iphone 4S running ios 5.01

I got an error cannot Find url when i attempt to play my camera recorded video from my iphone 4S 32 gig. I try to restart my phone but still no luck. There was no problem previously, but suddenly i got this problem with no reason. I also unable to copy the video to my computer using itunes. So please helppp...
Thanks a ton!!
Note: My iphone 4S is running ios 5.01.

See if it helps to delete the firmware file and download a new one:
Rename, move, or delete the iOS software file (.ipsw)
iTunes uses "ipsw" files to restore your iPod or iPhone. If those files are unusable, then try deleting them, renaming them, or moving the file to a different directory. This will cause iTunes to download a new copy of the IPSW. When a restore issue is specific to a user, it is likely due to an unusable .ipsw file. If removing the .ipsw file does not resolve a user-specific restore issue, then the issue is caused by other user-specific security software settings or iTunes preferences. Creating a new user will also cause new .ipsw restore files to be downloaded in the new user. You can find the ".ipsw" files in these locations:
Mac OS X
iPhone
~/Library/iTunes/iPhone Software Updates
iPad
~/Library/iTunes/iPad Software Updates
iPod touch
~/Library/iTunes/iPod Software Updates
Note: The tilde "~" represents your Home directory.

I get an error message when I connnect my digital camera to my Ipad 2 to dump pictures. Something about the device (camera) takes too much power?

I get an error message when I connect my digital camera to my Ipad 2. Something to the effect that the device takes too much power...Any ideas how to remedy?

Kevin-
I've read that Apple reduced the current limit for their Camera Connection kit, with one of the iOS updates. It is a known problem, so they may have made an adjustment with a later update. Be sure you have the latest version (4.3.3) on your iPad 2. If you continue to have the problem, report the details to Apple at
<http://www.apple.com/feedback/>.
One thing to try is to use your camera's memory card directly with the Camera Connection kit. (Use a card-to-USB adapter if the card is not SD.)
Fred

When I'm playing piano tiles it will not let me play the sound, same with when I'm playing something on any social media

When I'm playing piano tiles it will not let me play the sound, same with when I'm playing something on any social media

Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

Problem with MSI Nvidia GeForce 6800 LE (128MB) when playing 3D games

Games problem
I have bought a new MSI Nvidia GeForce 6800 LE (128MB) a couple of months ago and have been have loads of trouble when playing games.
In windows, the graphics card works fine. The computer never crashes and everything is speedy. Movies on DVD, Xvid, Divx all play fine without problem, the most I get is the occasional freezing and then windows will be normal again.
The problem arises when I try to play a 3D game. When I load up the game it goes into the menu screens ok, the computer will load up the 3D engine and it will play for around a minute nice and crisp then the screen will go blank and computer will lock up. Then all the drives will go quiet and the computer will make 3 beeps with the PC speaker. Pressing CTRL+ALT+DEL at this point does nothing, nor does the reset button. I have to turn the power on and off.
I really have no clue why this is happening, I have taken the covers off and kept it in a cool area, hoping that it was something to do with over heating, my computer is not overly cluttered and this has made no difference.
I have also unplugged the CDR, DVDR, USB ports, one Hard drive (storage) to see if it was something to do with the power no getting to the Videocard and then tried to play a game and the same problem arose.
I have two games that I have tried, Tiger woods 2005 and doom III, both of which crash in the same manner.
I have tried to be as detailed as I can with the descritopn of my computer below and the power details I'm not sure about so I posted a picture of the power unit to help.
Many thanks for your help in this matter, I'm desperately trying to get some worth out of this card and feel frustrated that its going bonkers only when trying to play games :/
Please tell me if you require further information about the system.
Neehar Shah
Model : Intel(R) Pentium(R) 4 CPU 3.20GHz
Speed : 3.21GHz
L2 On-board Cache : 512kB ECC Synchronous ATC (8-way sectored, 64 byte line size)
System BIOS : Phoenix Technologies, LTD 6.00 PG
Mainboard : Legend QDI PLATINIX-8
Total Memory : 511MB DDR-SDRAM
CPU
Model : Intel Corporation 82845G/GL/GE Brookdale Host-Hub Interface Bridge (B1-step)
Front Side Bus Speed : 4x 200MHz (800MHz data rate)
Total Memory : 512MB DDR-SDRAM
Memory Bus Speed : 2x 200MHz (400MHz data rate)
BOIS
Manufacturer : Phoenix Technologies, LTD
Version : 6.00 PG
Date : 06/19/2003
Plug & Play Version : 1.00
SMBIOS/DMI Version : 2.30
(EE)PROM Size : 256kB (2Mbit)
Video System
Monitor/Panel : SyncMaster 171S/ 175S/ 170S, SyncMaster Magic CX175S-AZ/LX175S
Adapter : NVIDIA GeForce 6800 LE
OEM Device Name : Nvidia Corp ??? (0042)
OEM Hardware ID : FUN_0, VEN_10DE, DEV_0042, REV_A1
Device Name : Micro-Star International Co Ltd (MSI) ??? (0042)
Product ID : VEN_1462, DEV_9751
Revision : K / 2 (161)
Physical Storage Devices
Hard Disk : Maxtor 6Y080L0 (76.3GB)
Hard Disk : ST3200822A (186.3GB)
CD-ROM/DVD : AOPEN CD-RW CRW2440 (CD 40X Rd, 24X Wr)
CD-ROM/DVD : PLEXTOR DVDR PX-708A (CD 40X Rd, 40X Wr) (DVD 5X Rd, 5X Wr)
Peripherals
USB Controller/Hub : USB 2.0 Root Hub
FireWire/1394 Controller/Hub : OHCI Compliant IEEE 1394 Host Controller
MultiMedia Device(s)
Device : MPU-401 Compatible MIDI Device
Device : Standard Game Port
Device : Creative SB Audigy
Device : Creative Game Port
Operating System(s)
Windows System : Microsoft Windows XP/2002 Professional (Win32 x86) 5.01.2600 (Service Pack 2)
Network Services
Adapter : Realtek RTL8139/810x Family Fast Ethernet NIC

Firstly, thank you for all your prompt responses, I really appreciate it. From the sounds of it, the PSU is ****
antec
From what I have read, the Antec PSUs have good reliability and ratings. I looked around and saw this one: Antec NEOPower 480W ATX PSU for around £65. I also went read that article posted by Dr Stu, which then stumbled on more articles about PSUs.
I have a couple more questions….
The rating of my system (http://www.jscustompcs.com/power_supply/Power_Supply_Calculator.php) with all the components running came out to be 422W. So do you think that the Antec NEOPower 480W ATX PSU would be sufficient for the computer considering I might add more RAM in the future?
Or should I buy the 500W+ one then?
Does anyone know if the Antec PSUs are quiet? My current q-Tec one makes me feel I'm in an aeroplane.
lucky I read the forum!
I was in Maplins (computer shop) at lunch and thought, that shiny 650W Q-Tec looks nice and there looks like loads of power, that much do the trick. i got to the counter and thought.....let me wait, till i get home from work and read some more on the forum about this PSU issue.
Thanks god I didn’t buy that S***. having read some of the reviews, i would have wasted loooots of money for nothing.

Windows 7 Crashes/Freezes when playing ANY Video files

lets see can anyone get their head around this one as it is driving me round the bend.
So... I have a media centre PC connected to my HDTV by VGA cable. I ran the PC on XP for a long time but last December, I upgraded it to Windows 7
along with my laptop.
Cue 5 months of seamless media usage and network integration - it
worked like a dream and I played both HD and SD content with ease.
About two weeks ago, I was watching an HD '.mkv' file in Windows Media Centre and about 10 minutes into the video, the video file just Froze - both the video and the audio. I had to power down and restart the machine and started the video file again. About
5 minutes after re-starting the video file, it hung again (not at the same place in the video). I then went and watched the video on my laptop where
it worked fine.
A few days after this (first time I had used it again since it hung up) I began watching an SD '.avi' file. About 1 minute into the video the display lost it's signal (the little built in 'no signal' graphic came up) and after a further 15 seconds, the audio
cut out as well.
This latter behaviour is now happening every single time I try to watch any kind of SD or HD video of any file extention. This problem is also independant of what video player I use (windows media centre and windows media player classic) After a minute or so
the display cuts out and the audio quickly follows it.
Suffice to say, I was a little annoyed but knowing a good bit about computers I
decided to try and solve the problem taking the following steps.
1) I uninstalled all my codecs and reinstalled the latest version of the K-Lite Codec pack. The latest version has support for windows 7 so I doubt its a compatibility issue here. After doing this the problem still persisted, exactly the same as before.
2) I checked the date of the drivers for my video card (MSI nVidia 6200) and seen that they were dated sept 2009. I went onto the nVidia site and found the latest win7 drivers dated april 2010 - I installed these but still the problem is there.
3) I then thought, maybe its a problem with the actual video card hardware itself. When I built my machine the parts supplier accidentally
sent me two of the same video card so I swapped out the existing one for a brand spanking new version of the same card. The problem is still EXACTLY the same.
So yes -I am rather annoyed and frustrated at the moment as I have absolutely no idea what is wrong with the machine and how it went from working to not working almost overnight.
I'd like to add also that the display is perfect when doing anything else on the computer - I can surf, play youtube videos, listen to music etc and it is absolutely no problem.
Put on a video and it cuts out the display like I have explained.
halp.

Hello Tim,
I decided to do a clean install, a fresh new installation of windows and all its updates, I didn't get the option of
install SP1 yet.
After that I only installed Catalyst drivers: 11.5 and Realtek HD audio drivers, all downloaded on May 24 2011.
Then latest FFDShow and MPC-HC to test, both x64 versions Nothing else installed.
Only a fresh copy of windows with its updates and those mentioned drivers.
To my surprise, it happened a gain.
It still crashes after a while when playing MKV videos.
It's weird, because it doesn't happen with avi's or mp4's.
So, there must be something wrong with one of windows updates that creates this windows FREEZE.
Also there is no possibility to find out what error it is in "Event Viewer" as nothing gets recorded there. Anyone could
advise?
Thanks

Camera roll empty but shows 6.1 gb. Restored to original settings after backing up. When I restored the backup camera roll still shows 6.1 gb and is till empty. I imagine that the backup contains some corruption

Camera roll empty but shows 6.1 gb. Restored to original settings after backing up. When I restored the backup camera roll still shows 6.1 gb and is still empty. I imagine that the backup contains some corruption

Hi cfgolf,
Thanks for contacting Apple Support Communities. I agree with your assessment that something is going on with that previous backup. If you restored from that backup and the issue continues, I would recommend restoring and Set up as new. Before you restore, make sure you Transfer content so that you can sync it back after setting up as new. The instructions on how to Transfer content and Set up as new are both listed in this article.
iOS: How to back up your data and set up your device as a new device
http://support.apple.com/kb/ht4137
2. Transfer content
Before you erase your device, take a few minutes to transfer your content from your device to your computer to ensure that all your critical data is safe.
6. Set up as new
Complete the setup assistant. When prompted to set up your device, select Set Up as New iPhone and tap Next to continue.
Skip the Apple ID sign-in, in case the original issue was related to any of your content on iCloud.
Note: After setting up as new, you will need to enter the Visual Voicemail password for iPhone (on carriers that support Visual Voicemail). If you've forgotten the password, contact your carrier to help you reset it.
After erasing and setting up as a new device, your device is now in a factory configuration. Test to determine if erasing and setting up as a new device resolved the issue. Content on the device may have caused unexpected behavior.
If the issue is still present, you may want to contact Apple Support.
If the issue is now resolved, sync one type of content at a time back to the device. For example, if you had an issue playing music, add songs from iTunes and confirm they will play. If your contacts weren't loading successfully, add the contacts back. After each sync, test to see if the issue has returned.
Cheers,
-Joe

Why would my video clips be running too fast when played on the monitor panel?

I posted my problem earlier today, but re-reading it maybe I didn't explain myself well enough.
My main question is: "why would my video clips be running too fast when played on the monitor panel ?". This is occuring after I have selected my media from the Tasks Panel and placed them in correct order in the Timeline/Sceneline. I knew something was wrong when I could see that the clips were not indicating their right length when viewed in the (expanded) timeline. They were compressed into just a few seconds, whereas the clips should have been at least 5 minutes. I ran the clips in the monitor and sure enough they ran too fast, with a lot of jerking movements.
The 3 video clips I am trying to make into a HD PAL video were taken with my Nokia N8 mobile video camera. These are in mp4 format. Can this present a problem ? Note that when I play these individual HD clips on my computer in (Windows Media Player) they run fine.
After I placed the clips in my Project Panel (or before in the Organize Workspace), I have perforned no change or manipulation of the clips. They are in their original state.
Just too confirm that the clips did seem to be compressed, I burnt a DVD, the resultant video ran in a matter of seconds.
Help would be greatly appreciated.

Yes, that is what the problem was.
Although the video camera on my Nokia N8, mobile was capturing at 25fps,
for some reason once transfered over to PrE9 (via file transfer), the clip was interpreted as 500fps. Once in Interpret Footage I was able to change the fps to 25.
Thanks for the help.

HT1222 When playing something recoded on cam no sound from mic.

Similar Messages

Maybe you are looking for