HT1338 I am using 10.5.8 and for a particular product download I need version 10.6.8. Any advice would be appreciated
I am using 10.5.8 and for a particular product download I need version 10.6.8. Any advice would be appreciated
You need to click here, buy the DVD, install it, and run Software Update.
(74763)
Similar Messages
-
i have recently upgraded to 7.0.2 and can no longer charge my iphone 4 as i recieve the message this accessory may not be supported, any advice would be appreciated
i have also tried 4 different chargers both official apple and non officiali have tried this but still not working i found a way of fixing it by restoring the phone but this has now put my phone in recovery mode and when i try to fix it i get an error 14 which i have no clue what it means
-
My iPhone cannot make or receive calls. I tried installing iTunes order to sync everything and restore, but I am getting 0x ... 084 errors, and it won't work. I do not want to delete all of my contacts. Any advice would be appreciated.
Oh, and I can't hook up my iPhone to iTunes because it's locked with a passcode. I can't begin to type the passcode because of this stupid "Restore Needed - can't send or receive calls" thing. This is beyond silly.
-
My MacBook is almost two years old and has started running really slow. It gets bogged down when it is running different programs at the same time, like Safari and Pages. It didn't react this way until recently. Any advice would be very welcome.
Launch Disk Utility and select the icon of the internal drive (the drive itself, not the volume icons below it.) Is the SMART status "Verified?" If not, replace the drive immediately. If the status is "Verified," the drive may still be failing. Back up all data, if you haven't already done so. Reinstall Mac OS X, then run Software Update. Test with all wired peripherals disconnected. If it's still slow, you have a hardware problem.
Mac OS X 10.6 Help: Reinstalling Mac OS X -
My iPad will no longer connect to my wireless sony speaker after installing IOS 7.0.4. I have reset the speaker and reinstalled through NS Setup but still no joy. Any advice would be most welcome. Thanks.
Hi,
When Zeen's battery level goes below 5 %; it tends to Reset to Default where it looses all the connections and sync to the printer or router.
So its very important to make sure that Zeen's battery does not go to low. To avoid this I would suggest to charge Zeen regularly.
You may try the steps below as of now and check the results.
We need to Factory Reset the Zeen making sure it is connected (Docked) on the C510a printer.
Once it is docked try the steps below:-
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02844556&cc=us&dlc=en&lc=en&jumpid=reg_r1002_us...
Open the above link; and then perform the Factory Reset as shown in Solution Two.
Once completed try connecting to Wireless and check the results.
though I am an HP employee, I am speaking for myself and not for HP. -
I recently had to wipe out my phone and lost everything! I have been able to recover all apps, pics, songs. Lost alot of my contacts due to me not backing up my info to icloud more often. (my mistake) However, I cant find any of my purchased ringtones. They are not showing up in my purchase history on itunes either. I do have the receipts for all of them tho.
Any advice or info would be greatly appreciated!Ringtones are currently a one-time only download, they won't appear under the Purchased tab nor in the cloud. Have you got copies of them in the Tones section of your computer's iTunes library or in the backup of your downloads that you can use to re-sync them to your phone ? If not, and they are still in the store, then you can try contacting iTunes support and see if they will grant you a re-download : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then try selecting Purchases, Billing & Redemption
-
Im sorry to ask this questioon, but am new to apple. Should i as recommended by apple buy and install intigo av, and can anyone advise me on Rapport as offered by the bank free of charge.
Can anyone tell me how to increase the font size of the menu bar at the top of the desktop screen without changing the display setting.
Told you I was newKevsmac...
You do not want Rapport...
Read a post from one of their representatives > Trusteer's Rapport Software: Apple Support Communities
If you want to install a/v software, use either ClamXav or Sophos.
Free Antivirus for Mac - Sophos Anti-Virus for Mac Edition
Apple - Downloads - Networking & Security - ClamXav
Good article here > Thomas' Corner : Mac Virus Guide -
Games downloaded direct to iPad. They are now auto downloading to iTunes on M/s PC and taking hours to do so. If I delete those partially downloaded to PC will it affect those on iPad when I next sync iPad with PC?
Any advice appreciated - thanks.
RefloTo start things off, I like to manually manage my media and will insturct you to do the same. To enable doing this, you check off the box for it on your phone's summary on iTunes. Now tranferring media is as easy as dragging and dropping.
(1) To get songs from your phone onto your iTunes, you open up your phone's dropdown menu on the iTunes sidebar and click Music. You can be able to drag music file into your Music folder in the Library section of iTunes. You can also just right click your phone's name and click "Transfer Purchases" if you want to move everything new on your iPhone onto your computer's library.
(2) You open your Music library on your computer and simply drag highlighted songs onto your phone's name on the sidebar. When in album grid view or cover flow, you can click and drag a whole album right on. The downside of manual management is that you can easily accidentally add doubles of songs onto your phone. Of course, if you notice this on your phone, you can just swipe to the right across the song's name and you should have a nice little delete button so you can remove extras anywhere.
(3) I heard about this online and it actually is buried in the Terms and Conditions somewhere. I don't think this rule will apply if you are exchanging the music over your iTunes account devices. I think this applies to buring the iTunes material to CDs. I think these speacial media file can somehow detect what they are moved or copied onto and keep a statistic buried in their coding. This is more of a logical assumption than a fact, but what else could these terms possibly mean? If you want to know more about this, Bruce Willis was having a big arguement about this online because he wanted to give his medie to his children. You can probably find an article about this using those search terms.
I worked hard on this response and would appreciate if you marked it correct if it served as any help to you. Thank you in advance. -
My Macbook Pro shows the Apple and spinning wheel at startup but will not continue the startup. Does anybody know how to get past this, so the computer continues to startup?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
I did the update to take out bugs etc; now when I try to open an app, it asks for my Itunes ID before it will open; this is a pain; has anyone else had this problem or knows how to correct this, assistance gratefully appreciated, thanks
Please tell me that it has NEVER been jailbroke. If it has never been jailbroke, here are some standard repair procedures:
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, read this. -
I am using chat-r wireless and facetime is not working but when i put rogers fido or any other carrier sim in it work. Anyone know what the problem?
I'm guessing it's a compatibility problem similar to that that T-Mobile in the US has. I'm not familiar with chat-r wireless, but I'm guessing it's not a supported carrier for the iPhone. If they can't tell you how to fix it, I'm guessing it's just plain not going to work.
-
I am using an Mac PPC version 10.5.8 and I am trying to download the correct version of Flash Player. I did once but I had to install a "Clean Install" of my computer and when finished I had put back the new Flash Player I just installed well every time I try install the new player it is place in my Trash Folder and I can not get Player to work. I did everything I was to install it correctly but it still does not install it correctly. Can some help me. Bob
Some MacBook Pro versions cannot be upgraded past 10.6.8; others are maxed out at 10.7.5. newer models can go all the way to 10.10. So it is important to know exactly what version you have--there may be close to 40 variants produced since the MB made its debut in 2006.
You can safely give us a snapshot of your model and its current config that will allow us to deternmmine your model and its upgrade potential, plus show it you have any software that may impede any upgrades. Please download and install this free utility:
http://www.etresoft.com/etrecheck
It is secure and written by one of our most valued members to allow users to show details of their computer's configuration in Apple Support Communities without revealing any sensitive personal data.
Run the program and click the "Copy report to clipboard" button when it displays the results. Then return here and paste the report into a response to your initial post. It can often show if any harmful files/programs are dragging down your performance.
Remember that, on leaving OS10.6.8, you lose the ability to run older softare written for older PowerPC Macs (yours in Intel-based). Programs such as Office 2004 will no longer work (min of Office 2008 needed to work on newer OS versions), and AppleWorks will stop working completely -
I am using Windows 7 Home Premium 64-bit OS.I've never had this problem before... today I opened iTunes and it prompted me to download the newest version. I use iTunes all the time and have updated it multiple times with no issues. During the installation process it gave me an error message that said:
Runtime error!
Program C:\Program Files\iTunes.exe
R0634
An application has made an attempt to load the C runtime library incorrectly.
Please contact the application's support team for more information.
I quit the installation, uninstalled iTunes and rebooted my computer. I now receive a similar message with a slight difference:
Runtime error!
Program C:\Program Files (x86)...
R0634
An application has made an attempt to load the C runtime library incorrectly.
Please contact the application's support team for more information.
I did not leave anything out from the error message. It doesn't point to a specific file, it just ends with "(x86)..." Every time I boot up my computer, this error message pops up on my desktop.
How do I repair this issue? I have found multiple suggested solutions but am unsure which one is the best, and I don't want to try a bunch of different things for fear I may make the problem worse. I would like to try and fix this myself if possible but I need to know if that is really possible or if I need to take my computer to someone for repairs. Any suggestions will be greatly appreciated!!Hi lustyln,
I'm having a little trouble understanding all of what you are trying to explain. From what I can tell, it sounds like your PC has a lot of software problems and you want to know what is supposed to be there and what isn't.
For reference, here are your product specifications:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01893242&lc=en&product=4043282
To get your PC software back to how it was when it was first purchased, run a system recovery:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01867418&lc=en&product=4043282
I hope this helps.
...an HP employee just trying to help where I can, but not speaking on behalf of HP. -
Hi
I'm using a 3GS (4.3.3) and itunes 10 2.2.12
When trying to sync my music my phone begins the syncing process, back up and preparing etc. Once it begins actually syncing it seems to get stuck on song 2 of 1500. After about 5-10mins a message appears saying song 2 of 1500 can not be copied because it can not be copied or read. Thats it. It doesn't try to sync the rest it just stops. The music is definitely available and it seems to have no problems syncing any podcasts. Any help would be appreciated. ThanksRemove the song in question from the sync list and see if the rectifies the problem.
If it does, then iTunes believes the song no longer exists on your drive and that will need to be corrected. -
Looking to create editable PDF forms with drop downs and text boxes for use on a Mac computer and iPad. Which product do I need to purchase? Do not need anything fancy
Basically you would need Acrobat. However, it is now also possible to create basic form fields using just the free Reader. In fact, I've been working on a tool that allows you to do it, so if you're interested in it please contact me privately.
Maybe you are looking for
-
Producer consumer vs state machine
Hi there, I have been on and around for quite a while to understand how can I re-design an application, which was originally built using a mix of sequence structure, while loops and event structures. And now I am making a newer version of the same ap
-
Hi, The problem page is located at http://gauravchandra.info/gpi/mediaCentre.html I am using flash query string to pass a value into a variable so that the flash file loads at a particular frame. If you see the object and embed element, I have writte
-
Publishing Captivate quiz using RoboHelp HTML 9
I am trying to publish a quiz made with Captivate 4 using RoboHelp HTML 9 webhelp pro output. The quiz is saved on a network drive and I tried to link out to it from Robohelp but that did not work so I imported the quiz html file into Robohelp and I
-
Adding 2 byte arrays (6 bytes each ) -any specific API available
hi friends I m fixed up with a problem . i want to add to arrays of six bytes each . how can i go for this . is there any specific API available for the same. current method i m using is an function which add first bytes of 2 arrays and then check ou
-
Creating an online help screen?
I am creating documentation for my company, and the ideal way to present it would be through an online help screen. When users are connected to the website, they would click a link, and a help screen would pop up. I can make the various pages in Dre