HT1338 i cant get to the startup disk

i cant go to the startup disk so i can reclean my labtop

Since nobody seems to know or if this is just like every other question I have ever asked to a Apple community and people just don't want to answer. I will answer it so someone knows. Call me a windows geek or heck, even a linux junkie, but I do like to help.
To get the disk to show up on XP (I assume that Vista is the same way or even easier) you go into control panel and open the Airport Utility Disk. This option is not located in the start menu and I can't seem to find it in the Manual. Once you have the Airport Utility Disk open, just select both options and type in the passwords you set for it when you were setting the Time Capsule up.
Would be nice if a few others were helpful as well.

Similar Messages

HT201394 I updated and restarted my iphone 5 now i cant get passed the startup? I have changed password many times and i have tried to skip it but it shuts off?

I updated and restarted my iphone 5 now i cant get passed the start up? I have changed password many times and i have tried to skip it but it shuts off?

I have same issue

Can i get the startup disks online for free for a used macbook i just bought?

can i get the installation stuff that i need to wipe all of the previous owners info off of my used macbook 13" laptop, so i can start over like new? my laptop did not come with all the startup disks or anything when i bought it.

No. Contact the seller, or phone AppleCare and buy replacements.
(106577)

I'm getting this error with bootcamp "The startup disk does not have enough space to be partitioned"

Here's the story...
I had a dual boot configuration on my mac with Mac OS X Lion and Windows XP (made with bootcamp).
I decided to reinstall windows.
I deleted the windows partition using BootCamp.
Tried to recreate the Windows partition with Boot Camp and got: "The startup disk does not have enough space to be partitioned You must have at least 10 GB of free space available"
After reading several posts on this forum I decided to defrag the hard drive and try again.
The defrag did not work and I'm still getting the error, I have 22 gb of free space on my drive.
Any suggestions?
Also, I tried repair disk and repair permissions
Hmm, my external harddrive says on the box "OS X 10.5.8 or higher (32-bit kernel only)" Could the 32-bit requirement be an issue? Is lion 64-bit?

Boot Camp must be able to allocate a contiguous block of space on the drive. If it cannot find 10 GBs of contiguous space, then you cannot create the Windows partition.
You will have to backup your OS X partition to an external drive, boot from the external drive, use Disk Utility to repartition and reformat your hard drive back to a single volume, then restore your backup to the internal hard drive.
Get an empty external hard drive and clone your internal drive to the external one.
Boot from the external hard drive.
Erase the internal hard drive.
Restore the external clone to the internal hard drive.
Clone the internal drive to the external drive
Open Disk Utility from the Utilities folder.
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.
Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears. Select the icon for the external drive and click on the downward pointing arrow button.
After startup do the following:
Erase internal hard drive
Open Disk Utility in your Utilities folder.
After DU loads select your internal hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed. Do not quit Disk Utility.
Restore the clone to the internal hard drive
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the internal hard drive. Source means the external startup drive.
Note that the Source and Destination drives are swapped for this last procedure.

I'm trying to up grade the os but I keep getting the startup disk is full I ordered more memory I was told this will not help. What do I do?

I'm trying to up grade the os but I keep getting the startup disk is full I ordered more memory I was told this will not help. What do I do?

I think as drive capacities increase, the old 10-15% becomes less accurate. The amount of free space you need doesn't really have anything to do with the drive size. So, increasing your drive size shouldn't mean that you need to have more free GB (which using a % of drive space would mean). You need free space to accommodate page outs (the amount of which would depend on how much RAM you have installed and how memory intensive the applications are), sleep images (again, this would max out at your total amount of RAM), and a bit to minimize fragmentation.
With desktop drives commonly in the 2TB range today, it is certainly not necessary to have 200GB+ free in order to maintain proper operation. I generally find about 30GB to be the minimum I'm comfortable with. Mind you, I pretty much always have way more than that available. But, if I'm working on a system and the amount of free space is at least 30GB, I would generally not site drive space as the cause of any performance issues. I'd say that 30GB is a minimum for a stable system (with 8GB or RAM installed). Of course at that amount, you would still need to free up space if you were to want to install or download any significant amount of data.
With servers being more likely to run into the 16GB of RAM range, more storage would be necessary. Most servers should be well stocked with storage, but the actual needs would vary greatly depending on what's being "served".
The 10-15% thing came about when we used to talk about drive capacities in hundreds of MBs and RAM in terms of KB (not MB and certainly not GB). More drive space is always a good thing, but as drive capacities continue to sky rocket, we don't need to dedicate larger amounts of storage on systems with the same specifications. A set amount of space is required for proper operation regardless of the capacity of the drive installed.

TS1702 how do i delete from the startup disk? I am trying to get Mountain Lion from the App store and it says that the purchase was not complete because i need 4.06 GB space to download OS x 10.8. and to remove items from my startup disk to increase space

how do i delete from the startup disk? I am trying to get Mountain Lion from the App store and it says that the purchase was not complete because i need 4.06 GB space to download OS x 10.8. and to remove items from my startup disk to increase space. How?
Thanks

You can use iCloud with 10.7.5. You do not need to upgrade to Yosemite. You should provide a minimum of 15 GBs of free space or 10% of the hard drive's capacity, whichever is greater.
Freeing Up Space on The Hard Drive
1. See Lion/Mountain Lion/Mavericks' Storage Display.
2. You can remove data from your Home folder except for the /Home/Library/ folder.
3. Visit The XLab FAQs and read the FAQ on freeing up space on your hard drive.
4. Also see Freeing space on your Mac OS X startup disk.
5. See Where did my Disk Space go?.
6. See The Storage Display.
You must Empty the Trash in order to recover the space they occupied on the hard drive.
You should consider replacing the drive with a larger one. Check out OWC for drives, tutorials, and toolkits.
Try using OmniDiskSweeper 1.8 or GrandPerspective to search your drive for large files and where they are located.

Imac frozen at blue screen after i went into disk utilities and cleaned my free space. I tried holding down T key as it reboots and i get a message. Start up disk full empty it how can one emptie it if you cant get past the blue screen

Imac frozen at blue screen after i went into disk utilities and cleaned free space.
I tried holding down T key as it reboots
and i get a message. Start up disk full empty it how can one emptie it if you cant get past the blue screen?
to make matters worse we bought the IMAC of amazon uk on the 4/07/011 so what can we do?
please remember how frustrating it is when asking for help when the helper telling you to type something on the screen when its frozen
Tell us when you can type some instuctions to the software how do you get to the doss prompt so to speak to do this
Thanks

i tried all this thanks
i can not get past blue screen and message Your disk is full it needs to be emptied Please not I cant proceed past this message.
no matter what you tell me
Am i right ok in thinking that
when i went into disk utilities and chose to clean my free space i left it over one hour to do its stuff
i came back and there was no progress bar just the box so i quit the program and when i opened mac mail the system just froze i forced quit mail rebooted and blue screen death
Now when free space is being cleaned is it the same as windows dose the utility write lots of 0 on the hard drive then rebbot its self to free the space
basicly is my hard drive full of 00000 is this why im getting this message because the process was interupted
I need to know if i need outside help i bought the computer on line on amazon uk what dose one do next

HT1338 i cant get in to os system. the screen just stuck in white screen and apple logo

i can not get in to my os system. the screen just stuck in white screen and apple logo

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

I am unable to start up my iMac running on 10.4.11 - the startup disk is installed and will not start up eben when I hold down the "C" Key. I do get the apple, but then it disappears.

I am unable to start up my iMac running on 10.4.11 - the startup disk is installed and will not start up eben when I hold down the "C" Key. I do get the apple, but then it disappears.

Query by serial number
Apple's warrenty database will identify the type of Mac you have. Your serial number is securely sent, but you get only the name of your machine.
https://selfsolve.apple.com/agreementWarrantyDynamic.do
This site provides more information, but lacks security.
"A serial number is a unique, identifying number or group of numbers and letters assigned to an individual piece of hardware or software. It's used for various things depending on the product / brand but what is your Mac's serial number for and more importantly... what is it hiding and what can it do for you ?"
http://www.appleserialnumberinfo.com/Desktop/index.php
or
This site provides more information, but lacks security too.
"A serial number is a unique, identifying number or group of numbers and letters assigned to an individual piece of hardware or software. It's used for various things depending on the product / brand but what is your Mac's serial number for and more importantly... what is it hiding and what can it do for you ?"
http://www.appleserialnumberinfo.com/Desktop/index.php
http://www.chipmunk.nl/klantenservice/applemodel.html
( hint by K Shaffer )

Icant upgrade mac os x 10.6.8 to 10.8.3, when i try it says the mac os 10.8.3 cant run on this startup disk what should i do?

Icant upgrade mac os x 10.6.8 to 10.8.3, when i try it says the mac os 10.8.3 cant run on this startup disk what should i do?

First we need to know which one of the 9 different models of MacBook you have. To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info. When System Profiler comes up check the Model Identifier and post it back here.
The Early 2006 model 1,1 Core Duo can only run a maximum of 10.6 Snow Leopard.
The models Late 2006 Core 2 Duos 2,1 through Early 2008 4,1 can only run a maximum of 10.7 Lion.
The Late 2008 model 5,1 Aluminum Unibody through the Mid 2010 White Unibody model 7,1 can run 10.8 Mountain Lion and 10.9 Mavericks.

I keep getting this message, I decided to delete whatever I can to free up some space. Then I get my few GBs I have left on the startup disk. Then after a day, I get the message again. I check the startup disk size and notice I have "zero kb" left. ??????

I keep getting this message, I decided to delete whatever I can to free up some space. Then I get my few GBs I have left on the startup disk. Then after a day, I get the message again. I check the startup disk size and notice I have "zero kb" left. ??????

Click your Apple menu icon top left in your screen. From the drop down menu click About This Mac > More Info > Storage
Make sure there's at least 15% free disk space.
Restart your Mac after freeing up disk space then check Stoage again.
Another way to view avialable space:
Control click the MacintoshHD icon on your Desktop then click Get Info.
In the Get Info panel you'll see: Available & Capacity
Again, make sure there's at least 15% free disk space.

My Macbook air keeps getting a message saying that the startup disk is full. I don't have picture, music, or movies on it. Im not sure whats wrong with it.

My Macbook air keeps getting a message saying that the startup disk is full. I don't have picture, music, or movies on it. Im not sure whats wrong with it.

The first step is to check and see how much space really is there. From the desktop right click on the drive in the upper right corner (at least it's there by default) and select "Get Info" to see how much space it reports as free.
It's not just media files that eat up disk space, though they are often a major contributor. Do you happen to be running one of the virtual machine programs (Parallels or VMWare Fusion)? When you create a guest drive there you normally have a fairly decent amount of disk space dedicated to it and that can fill the drive.
As well, a quick fix that may buy you some time is to empty the trash if you've not done so recently. Click on the trash folder in your dock and then in the window that comes up select the option to empty the trash.
If you can free up some space, there are programs that will help you find what files and directories are using disk space. I've used Space Gremlin (in the App store) for that sort of thing, though there others. If you run that sort of utlity you'll get some idea about what is really eating up the drive space.

HT3680 My 3 year old iMac is freezing and I get a message "startup disk almost full for running applications. delete files..." Where do I find the startup disk and what should I delete?

My 3 year old Mac is having trouble and freezes up from time to time lately. I get a message saying "startup disk almost full, delete files ..." something about having enough room for applications to function. I know my startup disk is the Macintosh HD, but what kind of files do I need to delete and how much space do I need to free up? In my "about this mac" area, it says I have 4.89gb free out of 319.21 So I am confused why I need to do this.

You're less than 2% free and should always have at least 15% (my SWAG). Best is to get an ext FWHD and move stuff from the startup disk to it and delete it from that. Best things to move are movies, music, and photos, using the apps that manage those things.

Trying to get rid of error "The startup disk cannot be partitioned or restored to a single partition". Recovery HD visible.

Hello,
I've been stuck for some hours now trying different things to install Windows 7 on my Macbook Air, and I think now is the time to call for some custom help.
I'm using OS X 10.9.5 Mavericks.
So some months ago I just wanted to run Linux on my laptop so I installed rEFInd, shrunk the Macintosh HD partition by 25GB and booted on a linux live USB flash I burned using dd.
Then I used gparted to create my linux partitions.
It worked just fine, even though disk utility from OS X seemed quite unhappy about this (it seemed to have incorrect informations about the filesystem on these partitions, seeing them as journaled Mac OS while they were clearly not). At this point already, the Recovery HD from mac showed up in disk utility, which I found weird but didn't bother me.
But recently I needed windows on my Mac. So after a few tries for the triple boot, I managed to create a bootable USB stick with boot camp, which already showed me the message "The startup disk cannot be partitioned or restored to a single partition" and hence refused to partition/install himself.
So I thought "OK, that's no big issue, I can just partition with disk utility and then boot on the USB stick and everything will work fine". But when EFI booting on the USB flash drive I got stuck at the beginning of Windows installer with no keyboard or mouse support.
After some hours spent googling, I was unable to find a working fix for that, and as there was no support for my case (where I used bootcamp to create the bootable flash but NOT to partition/reboot) I decided to give bootcamp a try.
So I erased my linux partitions, and cleaned up everything I could on the HD with disk utility. That means I now have two partitions showing in disk utility : Macintosh HD and Recovery HD.
When using disk utility from terminal, the list is :
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *121.3 GB   disk0
   1:                        EFI EFI                     209.7 MB   disk0s1
   2:                  Apple_HFS Macintosh HD            80.0 GB    disk0s2
   3:                  Apple_HFS Recovery HD             650.1 MB   disk0s3
But boot camp still isn't happy, and the message "The startup disk cannot be partitioned or restored to a single partition" keeps popping after the intro and I can't partition/boot from bootcamp.
So, as I don't understand what is wrong here anymore, any help would be greatly appreciated!
I will be watching the thread a lot because I really would like this resolved (or windows installed one way or another) this weekend; so any questions on my past manipulations or config just ask!
Thank you.

keyboard issues are also something of a common issue.
I wish the best threads were voted to the top of forums, something! Me, I literally burned out here, but after installing 10 Preview, wanted to "see what was going on" after hiatus of a couple years and see if anything had changed (no, not really!)
Also, these new Communities are not putting "more like this" and failing to help too.
I think rewriting Boot Camp Assistant's built in help and pdf would help a lot, and needs to be clearer and go into details. And Yosemite was not it seems tested against Boot Camp, and drivers for new Macs + new OS also lag behind. Again, common and no sign of improvement or change.
One of the tricks to the "can't partition" is rather simple - of course backup is step #1 and is spelled out - SHRINK the main HFS+ partition! then stretch it back to full length. Sometimes a reboot is needed, and sometimes even do a Safe Boot - not sure what but Recovry Mode might be a good option too. That does seem to consolidate free space, move files that are locked and cannot be moved otherwise, and allow BCA to partition, jusst be sure to have enough space left and large enough for a proper Windows install (and fudge factor).

How can I remove files from the startup disk

I am getting a screen when I am trying to quit saying the "MAC OS X startup disk has no more space available for application memory" by closing the windows and removing files from the startup disk will help.
How do I do this?

That error message is misleading. Your problem is excessive swapping of data between physical memory and virtual memory.
That can happen for two reasons:
You have a long-running process with a memory leak (i.e., a bug), or
You don't have enough memory installed for your usage pattern.
Tracking down a memory leak can be difficult, and it may come down to a process of elimination.
In the Activity Monitor application, select All Processes from the menu in the toolbar, if not already selected. Click the heading of the Real Mem column in the process table twice to sort the table with the highest value at the top. If you don't see that column, select
View ▹ Columns ▹ Real Memory
from the menu bar.
If one process (excluding "kernel_task") is using much more memory than all the others, that could be an indication of a leak. A better indication would be a process that continually grabs more and more real memory over time without ever releasing it. Here is an example of how it's done.
The process named "Safari Web Content" renders web pages for Safari and other applications. It uses a lot of memory and may leak if certain Safari extensions or third-party web plugins are installed. Consider it a prime suspect.
If you don't have an obvious memory leak, your options are to install more memory (if possible) or to run fewer programs simultaneously.
The next suggestion is only for users familiar with the shell. For a more precise, but potentially misleading, test, run the following command:
sudo leaks -nocontext -nostacks process | grep total
where process is the name of a process you suspect of leaking memory. Almost every process will leak some memory; the question is how much, and especially how much the leak increases with time. I can’t be more specific. See the leaks(1) man page and the Apple developer documentation for details.

HT1338 i cant get to the startup disk

Similar Messages

Maybe you are looking for