HT1338 Intel HD Graphics 288 MB graphics card +FCPX

Intel HD Graphics 288 MB graphics card in my Macbook pro, can I use new FCPX ? Can You update a macbook pro graphic card, to a more UTD graphics ard for FCPX?

Have a go at the link below to you give you a better idea on how much it would/should sell for.
http://www.mac2sell.net

Similar Messages

Repeated error from Intel integrated Graphics card in my brand-new B320

Hi
I am getting repeated errors from the Intel Integrated Graphics card (on the Intel i3 chip as I understand it) in my brand-new B320.
I checked via a tool from Intel that my drivers were up-to-date (version 15.22.1.2361).
I checked via Device Manager Update Drivers that my driver was up-to-date.
I attempted to uninstall and re-install my driver BUT the uninstall reverted me to a VGA Adapter (so my screen was then running in a low res 800x600 mode!) and I could not even then see the Intel Integrated Graphics card in Device Manager to be able to re-install the driver against (even if I ran scan for new hardware): I had to restore to a System Restore Point - so the problem has of course come back.
I have even had one error where the screen then went completely blank and nothing would bring it back: I had to power off the PC (Ouch!)
PLEASE advise how I rectify this incredibly frustrating problem step-by-step.

hey johnestlea,
i was going through the download list of the B320 here : http://consumersupport.lenovo.com/us/en/DriversDownloads/drivers_list.aspx?CategoryID=156819
And could not find any driver with the version 15.22.1.2361 for the Intel Integrated Graphic Card. Where did you get that version ?
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Replacing Intel hd Graphics card with ATI Radeon Graphics card

Hi, I am using an hp G62 b51SI notebook with an intel hd graphics card. However, am thinking of changing it or supplementing it with an ATI Radeon Graphics card for increased gamiing performance. Is it possible to do so?
This question was solved.
View Solution.

Hi:
Below is the link to the service manual for your notebook.
http://h10032.www1.hp.com/ctg/Manual/c02542102.pdf
The supported motherboards with HP part numbers can be found in chapter 3.

Intel i740 graphic card support in solaris 8

-does anybody know if i can use the old intel i740 8mb graphic card
on this solaris 8, because at the beginning of the instalation the
boot manager does not recognize my graphic card, and i have to set
a simple svga card support ....
i am waiting for an answer soon ...... than you !!!

Hi,
I have searched through our databases and did find that there was
considerable development of the Intel i740 Graphics Adapter driver.
Unfortunately, this driver was never released for late 2.6 or 2.7
and I cannot find any evidence of current driver development.
There may be Third party drivers available currently from http://www.xig.com as I am aware that they do write drivers for this card.
Regards
Derek SUN-DTS

Intel gpu graphic card dose over heat ?

i have a really bad experience with hp pavilion Dv6, i have many problems with GPU and overheating in the end the GPU corrupted and now i have to buy and replace new motherboard but the only mother board available now is the one with INTEL Graphic card not ATI , my question is if i replace the motherboard, does i going to suffer from the overheating problem again ?? is it better to replace my motherboard with the one that has intel GPU since that may reduce the overall temperature ??
note: my laptop is out off warranty.

The Intel integrated video will definitely run cooler than the ATI video model. The graphics performance will be quite a bit lower, but the Intel is good enough for anything except gaming and CAD and other intense graphics stuff.

Xinerama with a Mobile Intel 945GM graphics card

Hi,
I'm trying to write a xorg.conf to enable Xinerama. But as you've already guessed it isn't working.
Xinerama works perfectly fine, if i use xrandr.
Could please look over my config and tell me what's wrong?
Thanks in advance!
Informations you may need:
Im using the xf86-video-intel-legacy driver.
This is my xorg.conf:
Section "Monitor"
Identifier "Main Monitor"
EndSection
Section "Monitor"
Identifier "Second Monitor"
VendorName "ACR"
ModelName "Acer X233H"
HorizSync 30.0 - 94.0
VertRefresh 49.0 - 75.0
Option "DPMS"
Modeline "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync
EndSection
Section "Device"
Identifier "0 Intel 945GM"
Driver "intel"
BusID "PCI:0:2:0"
Screen 0
EndSection
Section "Device"
Identifier "1 Intel 945GM"
Driver "intel"
BusID "PCI:0:2:0"
Screen 1
EndSection
Section "Screen"
Identifier "0 Default Screen"
Device "0 Intel 945GM"
Monitor "Main Monitor"
SubSection "Display"
Depth 24
Modes "1280x800"
EndSubSection
EndSection
Section "Screen"
Identifier "1 Default Screen"
Device "1 Intel 945GM"
Monitor "Second Monitor"
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "0 Default Screen"
Screen 1 "1 Default Screen" LeftOf "0 Default Screen"
# Option "Xinerama" "true"
EndSection
Section "DRI"
Mode 0666
EndSection
# vim: sw=4 ts=4
And this is my /var/log/Xorg0.log:
X.Org X Server 1.6.0
Release Date: 2009-2-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.29-ARCH i686
Current Operating System: Linux skynet 2.6.29-ARCH #1 SMP PREEMPT Wed Apr 8 12:47:56 UTC 2009 i686
Build Date: 10 April 2009 07:03:14PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Apr 13 22:49:02 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Default Layout"
(**) |-->Screen "0 Default Screen" (0)
(**) | |-->Monitor "Main Monitor"
(**) | |-->Device "0 Intel 945GM"
(**) |-->Screen "1 Default Screen" (1)
(**) | |-->Monitor "Second Monitor"
(**) | |-->Device "1 Intel 945GM"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Loader magic: 0x1a40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7
(--) PCI:*(0@0:2:0) Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xdc100000/524288, 0xc0000000/268435456, 0xdc200000/262144, I/O @ 0x00001800/8
(--) PCI: (0@0:2:1) Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xdc180000/524288
(II) Open ACPI successful (/var/run/acpid.socket)
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 2.3.2
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
965GM, 965GME/GLE, G33, Q35, Q33, Intel Integrated Graphics Device
(II) Primary Device is: PCI 00@00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.1.0
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 5.0
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 945GM
(--) intel(0): Chipset: "945GM"
(--) intel(0): Linear framebuffer at 0xC0000000
(--) intel(0): IO registers at addr 0xDC100000
(II) intel(0): 2 display pipes available.
(==) intel(0): Using EXA for acceleration
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA using monitor section Main Monitor
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): Output LVDS has no monitor section
(II) intel(0): I2C bus "LVDSDDC_C" initialized.
(II) intel(0): Attempting to determine panel fixed mode.
(II) intel(0): I2C device "LVDSDDC_C:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) intel(0): initializing int10
(II) intel(0): Bad V_BIOS checksum
(II) intel(0): Primary V_BIOS segment is: 0xc000
(II) intel(0): VESA BIOS detected
(II) intel(0): VESA VBE Version 3.0
(II) intel(0): VESA VBE Total Mem: 7872 kB
(II) intel(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip Accelerated VGA BIOS
(II) intel(0): VESA VBE OEM Software Rev: 1.0
(II) intel(0): VESA VBE OEM Vendor: Intel Corporation
(II) intel(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics Controller
(II) intel(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) intel(0): found backlight control method /sys/class/backlight/acpi_video0
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): No SDVO device found on SDVOB
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(0): No SDVO device found on SDVOC
(II) intel(0): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOC" removed.
(II) intel(0): Output TV has no monitor section
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): EDID vendor "ACR", prod id 147
(II) intel(0): Using EDID range info for horizontal sync
(II) intel(0): Using EDID range info for vertical refresh
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(0): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(0): Modeline "1280x800"x0.0 83.50 1280 1352 1480 1680 800 803 809 831 -hsync +vsync (49.7 kHz)
(II) intel(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(0): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
(II) intel(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz)
(II) intel(0): EDID vendor "ACR", prod id 147
(II) intel(0): Output VGA connected
(II) intel(0): Output LVDS connected
(II) intel(0): Output TV disconnected
(II) intel(0): Using user preference for initial modes
(II) intel(0): Output VGA using initial mode 1280x800
(II) intel(0): Output LVDS using initial mode 1280x800
(II) intel(0): Monitoring connected displays enabled
(II) intel(0): detected 256 kB GTT.
(II) intel(0): detected 7932 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Will not try to enable page flipping
(==) intel(0): Triple buffering disabled
(==) intel(0): Intel XvMC decoder disabled
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(**) intel(0): Display dimensions: (510, 290) mm
(**) intel(0): DPI set to (95, 168)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/lib/xorg/modules//libexa.so
(II) Module exa: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 2.4.0
ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) intel(0): Comparing regs from server start up to After PreInit
(WW) intel(0): Register 0x61200 (PP_STATUS) changed from 0xc0000008 to 0xd000000a
(WW) intel(0): PP_STATUS before: on, ready, sequencing idle
(WW) intel(0): PP_STATUS after: on, ready, sequencing on
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Reloading /usr/lib/xorg/modules//libvbe.so
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Reloading /usr/lib/xorg/modules//libvgahw.so
(==) intel(1): Depth 24, (--) framebuffer bpp 32
(==) intel(1): RGB weight 888
(==) intel(1): Default visual is TrueColor
(II) intel(1): Integrated Graphics Chipset: Intel(R) 945GM
(--) intel(1): Chipset: "945GM"
(--) intel(1): Linear framebuffer at 0xC0000000
(--) intel(1): IO registers at addr 0xDC100000
(II) intel(1): 2 display pipes available.
(==) intel(1): Using EXA for acceleration
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(1): Output VGA using monitor section Second Monitor
(II) intel(1): I2C bus "CRTDDC_A" initialized.
(II) intel(1): Output LVDS has no monitor section
(II) intel(1): I2C bus "LVDSDDC_C" initialized.
(II) intel(1): Attempting to determine panel fixed mode.
(II) intel(1): I2C device "LVDSDDC_C:E-EDID segment register" registered at address 0x60.
(II) intel(1): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) intel(0): initializing int10
(II) intel(0): Bad V_BIOS checksum
(II) intel(0): Primary V_BIOS segment is: 0xc000
(II) intel(0): VESA BIOS detected
(II) intel(0): VESA VBE Version 3.0
(II) intel(0): VESA VBE Total Mem: 7872 kB
(II) intel(0): VESA VBE OEM: Intel(r) 82945GM Chipset Family Graphics Chip Accelerated VGA BIOS
(II) intel(0): VESA VBE OEM Software Rev: 1.0
(II) intel(0): VESA VBE OEM Vendor: Intel Corporation
(II) intel(0): VESA VBE OEM Product: Intel(r) 82945GM Chipset Family Graphics Controller
(II) intel(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) intel(1): found backlight control method /sys/class/backlight/acpi_video0
(II) intel(1): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(1): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(1): No SDVO device found on SDVOB
(II) intel(1): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" removed.
(II) intel(1): I2C bus "SDVOCTRL_E for SDVOB" removed.
(II) intel(1): I2C bus "SDVOCTRL_E for SDVOC" initialized.
(II) intel(1): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" registered at address 0x72.
(II) intel(1): No SDVO device found on SDVOC
(II) intel(1): I2C device "SDVOCTRL_E for SDVOC:SDVO Controller C" removed.
(II) intel(1): I2C bus "SDVOCTRL_E for SDVOC" removed.
(II) intel(1): Output TV has no monitor section
(II) intel(1): I2C device "CRTDDC_A:E-EDID segment register" registered at address 0x60.
(II) intel(1): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(1): EDID vendor "ACR", prod id 147
(II) intel(1): Using hsync ranges from config file
(II) intel(1): Using vrefresh ranges from config file
(II) intel(1): Printing DDC gathered Modelines:
(II) intel(1): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
(II) intel(1): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(1): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) intel(1): Modeline "640x480"x0.0 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
(II) intel(1): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(1): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) intel(1): Modeline "1024x768"x0.0 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
(II) intel(1): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(1): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) intel(1): Modeline "1280x800"x0.0 83.50 1280 1352 1480 1680 800 803 809 831 -hsync +vsync (49.7 kHz)
(II) intel(1): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) intel(1): Modeline "1440x900"x0.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
(II) intel(1): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz)
(II) intel(1): EDID vendor "ACR", prod id 147
(II) intel(1): Output VGA connected
(II) intel(1): Output LVDS connected
(II) intel(1): Output TV disconnected
(II) intel(1): Using user preference for initial modes
(II) intel(1): Output VGA using initial mode 1920x1080
(II) intel(1): Output LVDS using initial mode 1280x800
(II) intel(1): Monitoring connected displays enabled
(II) intel(1): detected 256 kB GTT.
(II) intel(1): detected 7932 kB stolen memory.
(==) intel(1): video overlay key set to 0x101fe
(==) intel(1): Will not try to enable page flipping
(==) intel(1): Triple buffering disabled
(==) intel(1): Intel XvMC decoder disabled
(==) intel(1): Using gamma correction (1.0, 1.0, 1.0)
(--) intel(1): Using HW Cursor because it's enabled on primary head.
(**) intel(1): Display dimensions: (510, 290) mm
(**) intel(1): DPI set to (95, 168)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Reloading /usr/lib/xorg/modules//libfb.so
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Reloading /usr/lib/xorg/modules//libexa.so
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) intel(1): Comparing regs from server start up to After PreInit
(WW) intel(1): Register 0x61200 (PP_STATUS) changed from 0xd0000009 to 0xd000000a
(WW) intel(1): PP_STATUS before: on, ready, sequencing on
(WW) intel(1): PP_STATUS after: on, ready, sequencing on
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? Yes, I do.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprD)
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprD)
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprD)
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) intel(0): Kernel reported 488960 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 1955836 kB available
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenByBusid: drmOpenMinor returns 11
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) intel(0): [drm] Using the DRM lock SAREA also for drawables.
(II) intel(0): [drm] framebuffer mapped by ddx driver
(II) intel(0): [drm] added 1 reserved context for kernel
(II) intel(0): X context handle = 0x1
(II) intel(0): [drm] installed DRM signal handler
(**) intel(0): Framebuffer compression enabled
(**) intel(0): Tiling enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
Backtrace:
0: /usr/bin/X(xorg_backtrace+0x3b) [0x813278b]
1: /usr/bin/X(xf86SigHandler+0x51) [0x80dda61]
2: [0xb7fcb400]
3: /usr/lib/xorg/modules/drivers//intel_drv.so [0xb7a5258e]
4: /usr/lib/xorg/modules/drivers//intel_drv.so(i830_allocate_2d_memory+0x144) [0xb7a527b4]
5: /usr/lib/xorg/modules/drivers//intel_drv.so [0xb7a47e2b]
6: /usr/lib/xorg/modules/drivers//intel_drv.so [0xb7a4cafd]
7: /usr/bin/X(AddScreen+0x19d) [0x807167d]
8: /usr/bin/X(InitOutput+0x206) [0x80aeb16]
9: /usr/bin/X(main+0x1e1) [0x8071d61]
10: /lib/libc.so.6(__libc_start_main+0xe5) [0xb7bab6c5]
11: /usr/bin/X [0x8071401]
Fatal server error:
Caught signal 11. Server aborting
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.

Blind wrote:Umm, weelll, xorgconfig or X -config might produce something to work with, but in general you need to edit the xorg.conf file for best performance. As to your editing of 'vga' to 'xf86-video-intel': you should replace it with 'intel'. There are many, many sample xorg.conf's out there that use the intel driver, so google is your friend.
Cheers,
Blind
+1
You can specify the amount of videoram in xorg.conf and you need to add the 1280*800 resolution to it too. That's all I had to do to get it to work on my father's laptop.
Zl.
/EDIT: numerous wiki-entries could help you, f.e. http://wiki.archlinux.org/index.php/Intel_GMA_950
Last edited by zenlord (2008-01-21 09:54:09)

Best graphics cards fcpx Mid 2010

I"ve seen similar posts but none matching what I need which is...out of the card list by apple which card(s) is the best option to get fcpx to run faster and eliminate the spinning wheel on a Mid 2010 2.8ghz Quad-Core Intel Xeon with 28gb of RAM and running Mountain Lion? I"m going to max out the RAM which I know will slightly help, but I also know fcpx needs the RAM on the graphics card and what I have now, the ATI Radeon HD 5770 1024, isn't cutting it. My budget is between 350 and 400 and I don't want to get into flashing PC graphics cards, just buy the best card for my mac that will outdo this stock ATI. Thanks

> you can get the power from it with serial ata to molex female and 6pin PCI Express power to molex male cable.
Would not and is not recommended, not by eVGA and not by most users, unless you like to cut corners and take chances that is.
Did I see that you mentioned you were using an external 500W PSU? don't see it mentioned, and your photos were all the ways that are to be avoided unless you know for a fact that the cards really aren't going to 'ask' for more watts and just need some any power connectors to see if it 'works' (boots and displays video). And while some 450W PSU are marketed for GPUs that is just because 450W is small, often talking about special flat units that are designed to fit into those spare optical drive bays many have available (and PC cases have an abundance of).
you need 450W PSU. That was just an adapter to go from 6-pin to an 8-pin (1) anyway. You want standard 6-pin PSU cables (4) so you need two more (non-Apple) to go to the PSU you add.
There needs to be at least 4x6-pin connectors, Mac Pro only has two.
http://www.amazon.com/450W-Graphics-Power-Supply-Juice/dp/B001AO4O98/
http://www.amazon.com/FSP-CrossFire-Upgrade-BOOSTER-X5/dp/B002IZE5RE/
and then maybe this if power cable is too short.
http://www.amazon.com/Kingwin-12-Inch-Express-Extension-PCI-01/dp/B004VR7UJM/
This is a risky Y-splitter to go from a 6-pin to 2x6-pin and which would impose risks.
http://www.amazon.com/PCIe-Power-Cable-nVidia-Video/dp/B0051PWFCU/
Extension 6-pin
Kingwin 12-Inch PCI Express 6 PIN Extension Cable (PCI-01)
http://www.amazon.com/Kingwin-12-Inch-Express-Extension-PCI-01/dp/B004VR7UJM/
I like the photo of how to wire up a booster PSU - click to see full diagram - with all the cables.
http://www.amazon.com/FSP-CrossFire-Upgrade-BOOSTER-X5/dp/B002IZE5RE/
http://ecx.images-amazon.com/images/I/61-DyTAR8LL._AA1000_.jpg

Intel 4600 graphics card...causes Premiere to crash when I try to view an imported file

I have an hp laptop with 16gb ram and an Intel Core7 processor. Any help on how to fix this would be great. I have tried to switch both the Mercury software and Open GL options. Both still get the same results. Also tried many different forms of media to edite...jpgs..clips with and with out audio. Just greay outs and gives the pop up that it is not working and closes down.

Do you have dual graphics adapters?
Go to the Windows Control Panel and select Hardware and Sound and then select Device Manager... In Device manager you click the + sign to the left of Display Adapters... and see if 2 are listed
IF YES, read below
-http://helpx.adobe.com/premiere-pro/kb/error---preludevideo-play-modules.html
-http://forums.adobe.com/thread/1001579
-Use BIOS http://forums.adobe.com/thread/1019004?tstart=0
-link to why http://forums.adobe.com/message/4685328
-http://www.anandtech.com/show/4839/mobile-gpu-faceoff-amd-dynamic-switchable-graphics-vs-n vidia-optimus-technology/2

Will Adobe CS5 work with Intel HD Graphics card 3000?

I am thinking about buying this laptop. http://www.staples.com/HP-Pavilion-dv7-6163us-17.3-Laptop/product_343565
Will Adobe CS5 run on it OK?

Both of the HP laptops that you mentioned will be quite sluggish in running CS5, even compared to a cheap $400 desktop:
1) Neither of those laptops have more than one single internal hard drive, which is already below Adobe's stated minimum requirements. Adobe requires a minimum of two discrete fast hard drives (no partitions) in order to run CS5 at all. Unfortunately, neither of those HP laptops have an eSATA port at all. (Those HP laptops have two USB 3.0 ports - but USB by itself doesn't support RAID at all.) Nor does either of those two laptops have any provision whatsoever to accommodate nore than the included internal hard drive.
2) Based on the CPU alone, your first choice of a laptop with an i7-2630QM is better - but only if it also has an Nvidia GPU with 1GB or more. The CPU in your second choice, an i5-2410M, is only a dual-core CPU (in fact, all mobile i5's are only dual-core) - and no system (laptop or desktop) with a dual-core CPU performs as well in CS5 as even a mediocre system with a quad-core CPU.
3) Neither of those two HP laptops come with (or is even available with) a GPU that supports MPE GPU acceleration. The first choice has only the integrated Intel HD 3000 graphics while the other comes with an onboard AMD Mobility Radeon GPU. And as we all know, both of those systems would have run CS5 only in MPE software-only mode. There is a plugin to allow CS5 to utilize the QuickSync feature of the first laptop (the second one cannot utilize QuickSync at all because it uses a discrete GPU) - but that would have speeded up only the encoding times (it would not have helped rendering times much if at all).
4) All consumer HP systems - both laptop and desktop - come pre-loaded with a ton of bloatware that cannot be easily uninstalled (or more precisely, software whose uninstallation still leaves behind pieces of it that actually slows down system performance and/or makes it run less stably). Worse, neither laptop includes a system restore disk (all of the restore files are on a locked hard drive partition that can only be accessed by one of HP's authorized service facilities). HP will sell you a recovery/restore disk, but that will cost you an additional fee.
5) Both of those systems come with only 6GB of RAM. In the case of laptops, 8GB is recommended if you're going to run CS5 much. Although the systems theoretically support 16GB of RAM, those two laptops have only two DIMM slots, and there are currently no compatible 8GB modules on the market.
6) Finally, the internal hard drive spins at only 5400 RPM. Laptop hard drives, as a rule, are slower than desktop hard drives (sequential speed wise). You'd be lucky if that 750GB 5400 RPM hard drive can sustain even half the sequential speed of the slowest current-production "Green" desktop hard drive.
As a result, both of those laptops would have been slower in the PPBM5 benchmark than most (if not all) of the desktops on the PPBM5 results list.
Message was edited by: RjL190365

I've not found the option to increase shared memory of intel hd graphics card in BIOS

Hi! I don't find that option. I have the 2.08 version, but the 3.01 is out there. The graphics performance is not very well now. Is there a way to increase this memory to 256 mb or more? Thanks in advance

hi freinn,
Welcome to Lenovo Community Forums!
This is on Auto by default.
The amount of memory shared to your graphics is dependent on how much RAM you have. Also even if you max out the RAM capacity there will no big jump on the shared memory just few MBs will be added
The Manual is not available even if there is an updated BIOS.
Even if a Manual option is available still you can only share the same maximum as the one on Auto. Not a big jump.
i hate to say it but that's how it will be
Hope this helps
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

G500 intel graphic card

Hello,
I was just wondering can my g500 laptop with windows 8.1 and the dedicated and intergrated intel/raden graphic card view 3d drawings if so, which graphic card do I need to switch it to and how.
Thanks

hi fishermanjack,
Welcome to Lenovo Community Forums!
In terms of Graphics rendering the Discrete graphics AMD Radeon is the one for the job.
But your system is configured to auto switch the graphics when needed.
Like When you turn on the computer, the Intel is the one processing everything even in word processing software to playing audio.
But in case you launch an application that needs heavy graphics rendering The AMD Radeon will kick in and take over Automatically.
Hope that answers your question.
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Unable to update Intel HD graphics drivers on my new computer

Hi,
I just recently bought a desktop HP Pavilion PC with Windows 8 64-bit which includes an Intel HD Graphics card but when I try to download the latest driver for my graphics (version 15.33.18.64.3496) on Intel's site it says I need to download it from PC manufacturer.
When I search for this update either on HPs site or using HP Support Assistant, it is not appearing so I cannot download it. This is causing me to run games in 'fair' graphics to lower the framerate and the games all say i need to update my video card.
Please help, growing frustrated!!
P.S. i've now upgraded to Windows 8.1 but still not resolved the issue.
Thanks,
Admurphy85

Thank you for the additional information.
I normally recommend a PSU with at least 500W. However, 600W is better for future upgrades. Here is a Corsair PSU that will do a good job. Corsair makes enthusiast quality products for a good price. It is best to measure the existing PSU to assure that the new one will fit.
As for video cards, I like XFX, EVGA, Sapphire and PNY in that order. I came to these preferences from being on many enthusiast/gamer forums over the years. You should pick a video card and get the measurements. Then, make a template the same size and to see if it will fit into the space provided. You should add at least one inch if the card has extra power connector/s. Normally, a card in the range of 9" to 9.5" will work fine. Newegg is a good place to shop for cards. Their specifications are more complete than other etailers. It would be good if you find a card. Post a link and I will review it for you.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Is it possible to add a graphics card to the back of my HP

Hello I want to know if it's possible to add a new graphics card to the back of a Laptop not inside of it but on the back of my laptop ??? my graphics Card is a Intel 4000 graphics card is a terrible for gaming TERRIBLE !!!

Not sure where it would go on the back, but no the system is closed. There is no place to insert a graphics card or attach it. You will find some hokey stuff on the internet where people say you can plug a video card in the wireless card slot but those are a hoax at worst and at best they do not tell you that such a thing would not even perform as well as what you have and is likely to damage the motherboard.

Graphic Cards for Photoshop CS6

I have been using photoshop CS5 and just upgaded to CS6. Now I get a message that my graphic processor card is unkown. My computer has an Intel family graphic card. This card was supported in CS5, and I can't find a list for CS6 compatible cards. Do I repalce the intel card or wait for a future upgrade?

Well, to be straight: You can probably wait for support for intel chipsets until your hair falls out. Sorry, but intel chips are notoriously full of hardware bugs and come with the most atrocious drivers, so chances that this will ever work properly are extremely slim, even if there may be updated drivers one day. Therefore the only logical course of action is to buy a dedicated graphics card from NVidia or AMD/ ATI. Even one from the 50 Euro budget tray will be better than anything you could ever hope to achieve with an intel onboard chip.
Mylenium

Graphics card issue recognition issue

I purhcased the 15", 16G, i7 ect. Standard, no upgrades. On the site it says it has the Intel Iris graphics card, AS WELL as the NIVIDIA Geforce, but when I go to "about this system" it lists as the Iris card. Is this just due to the automatic graphics switching? Can someone clear up the whole dual graphics thing for me. Thanks.

ConnorBurnsHGR wrote:
Is this just due to the automatic graphics switching?
Yes.
You can manage your card with the software gfxCardStatus. http://www.http://gfx.io

HT1338 Intel HD Graphics 288 MB graphics card +FCPX

Similar Messages

Maybe you are looking for