HT1338 My computer screen is grey and has a folder with a question mark on it

If was just grey with apple then got it to safe start loads the bar then it shuts off what now

A folder with a question mark at boot means the startup drive can't be found. It may be damaged or even dead as a doornail.
Hold down the command and r keys at boot and use the Disk Utility app to see if it can be repaired.

Similar Messages

  • Hi, I accidentally spilled water on my Mac Air on the very right side of the keyboard. After a few minutes, the screen turned white and a gray folder with a question mark came up and kept flashing. THEN IT DIED HELP.

    After the screen turned white and the folder popped up, it just kept flashing. After a few minutes the screen just turned white completely and I could hear the noise of the drive. It just sat there still with the noise for a good few hours until the battery died and then my mac just shut down completely. I tried to see if the computer could charge, and it does charge. I just can not turn the computer on no matter what. It is dead. It might be the logic board or the drive...I'm hoping it won't cost me a new computer because I just got this 5 months ago....

    Do not attempt to charge as that will only make the damage worse.  You need to take the MacBook Air to an Apple store genius bar and have the technicians check and see what repair work is necessary.  It only takes a very small amount of liquid to cause short circuits and damage.

  • I turn my Mac on the screen is white and has a folder with a '?' In  middle?.

    I turn my Mac on the screen is white and has a folder with a '?' In  middle?

    •A Flashing Question Mark appears when you Start your Mac:
    http://support.apple.com/kb/TS1440
    Read through & follow the instructions; if the problem goes away after completing
    any of them, you need not continue through all of them to resolve this issue.
    This also helps troubleshoot some of the main possibilities.
    Short of some hardware failure requiring major parts.
    Good luck & happy computing!

  • My new mac mini (3 month) didn't start up,all that appeared was a white screen and a flashing folder with a question mark inside it.

    My new Mac mini (3 month) didn't start up, all that appeared was a white screen and a flashing folder with a question mark inside it.
    I followed by recommendations from 'Everything Mac': "shut it down by pressing and holding the power button for about 5 seconds.
    Then hold down the Option key and press the power button again to start up the Mac mini. Keep holding down the Option key until
    the Mac mini starts up."
    But I got a Wi-Fi button only to chose and connect the local network. I connected to my network and I can't use this connection
    becouse no icons.
    Could you please help me?

    Your Mini (running 10.6.4) should have come with grey-colored install disks. Now is the time to put them into service. Turn on your computer so that there is power to accept disk #1 into the optical drive. Once  the disk is in the drive, shut off the computer by holding the start button down until it powers off. Then turn it on this time holding down the "C" key to make the computer boot from the disk. The question mark that you saw indicates that the computer cannot find a bootable volume. This can happen due to corrupted system files or an improper shutdown etc. Once you are in the "Installer" you can choose Disk Utility from the Utilities Menu in the menu bar. Use it to repair the disk and to see if that can solve your trouble.  

  • Laptop turns on but has a folder with a question mark in the middle

    for the last month or so my computer has been acting weird. when i turnd it on one morning it wouldent load it just kept the apple sign logo on the screen then it would change too the circle with a line though it sign.
    now the logo doesnt even show up and a folder with a question mark on it is shown. is there a way to fix this problum and if so estimated how much...

    Hi wizy;
    It sounds like either your disk or the directories on your disk have been slowly going bad.
    Do you have a backup?
    The question mark indicates that your Mac is not able to find a system to boot from. I would suggest that you boot form the install media for your Mac and repair the disk with Disk Utility. Let us know the results of that and we can go from there.
    Allan

  • It has a folder with a question mark. Did I break it?

    I accidentally bumped into my Macbook a few days ago and it fell...I thought it was fine until later I tried to turn it on and, to my dismay, it has a blank screen with the exception of a folder with a question mark on it.
    Is it an invalid now? What do I do?

    Try this:
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now shutdown the computer for a couple of minutes and then restart normally.
    If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    If the above doesn't help, but otherwise shows the drive is OK, then you need not replace the drive. However, you will need to reinstall OS X. You may do that without erasing the drive:
    How to Perform an Archive and Install
    1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger) and/or TechTool Pro (4.5.2 for Tiger) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
    3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
    4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
    5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
    6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.
    Now, if the drive is toast but still mounts you may be able to recover some of your personal data before replacing the drive:
    Basics of File Recovery
    Recovery is possible but you must not allow any additional writes to the hard drive - shut it down. If you stop using the drive it's possible to recover deleted files that have not been overwritten by using data recovery software such as Data Rescue II, File Salvage or TechTool Pro. Each of the preceding come on bootable CDs to enable usage without risk of writing more data to the hard drive.
    The longer the hard drive remains in use and data are written to it, the greater the risk your deleted files will be overwritten.
    Also visit The XLab FAQs and read the FAQ on Data Recovery.

  • Macbook has the folder with flashing question mark

    Yesterday as I was watching Netflix my Mac froze. I was skipping around an episode and then started opening a folder to do something else while it loaded and then it just froze. I thought maybe I was clicking on too many things at once or whatever and it got screwed up a bit so I closed it for a minute or two. When I opened it back up it had a (light) blue screen that wouldn't go away so I shut it down with the power button. Then when I turned it back it just had a white/gray screen for like a minute before the folder with the flashing question marked appeared.
    I've googled possible solutions but nothing seems to work. It won't boot up in safemode. One answer suggested trying to do comm-opt-P-R (can't remember what that was trying to do) and that didn't work. The screen would just go black and then start up over and over. When I just press the opt-key it takes me straight to Internet recovery. However, none of the options available work. I don't have the TimeMachine thing, I don't have a disk to reload the Lion software, and there's nothing to click on at all in the disk utility. All that's available in that is a disk0 and the Mac OS X Base System and I can't click on First Aid/Erase/Partition/Restore. I've opened up the startup disk and there's nothing that shows up.
    Is there something else I can try at home or should I just go ahead to the apple store? My Mac is under a year old still, but I spilled soda on it back in like October and had to get all the parts replaced so I don't know if that would do anything to the warranty....And if something does have to get replaced will I lose all my stuff? It was bad enough losing four months worth of data, I don't want to lose seven.
    Thanks for any help.

    As long as the parts were replaced by someone authorized to do the repairs, you should still be fine. This error indicates that they computer isn't able to find a disk to boot to.
    The "disk" to reload Lion is that internet recovery (also can be launched from command + r).
    Seeing as how you don't have the startupdisk in Disk Utility, I would recommend getting it into a store to see why that drive isn't detected. It could be something as simple as a loose SATA cable, or as catastrophic as complete hard drive failure. While you're at the store, I'd look into investing in an external drive to start running Time Machine...

  • My screen has gone blank on startup and occasionally a grey folder with a question mark appears. I have tried rebooting either by pressing the start up with power or pram.. Neither attempts have worked ! My iMac is 2008. Please help :)

    My screen has gone blank on startup and occasionally a grey folder with a question mark appears. I have tried rebooting either by pressing the start up with power or pram.. Neither attempts have worked ! My iMac is 2008. Please help :)

    Hey Carolinearnold!
    I have an article for you that seems to address this issue and can provide some troubleshooting steps for you:
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/ts2570
    Thanks for using the Apple Support Communities. Have a good one!
    -Braden

  • IMac won't boot and has flashing folder with question mark on gray screen

    I just bought a new iMac. I have been trying all week (with no success) to transfer files and apps from my previous iMac. The last time I tried to transfer, I used target mode on the old computer. It looked as if it was finally working, so I left with 2+ hours remaining on the transfer. When I returned, the computer was frozen and nothing would work. So I held the power button to turn it off. When I tried to turn it back on, there was only a gray screen with a flashing folder with a question mark. I feel like I have tried everything listed in other discussions. The only thing I am not able to try is to reinstall Lion because the new computer did NOT come with an OSX disc of any type. Any suggestions?

    Go to > OS X Lion: About Lion Recovery

  • My MacBook Pro won't start - it just displays a grey screen with flashing icon of a folder with a question mark in the middle. Help.

    It started while I was using Adobe InDesign, and that program froze, then crashed. When I tried to reopen the program, the error message I received was simply "Error: 16".
    I tried to take a screen shot of the error message for reference, and it gave me a message saying I couldn't because I didn't have access to the files where it would normally store the shot.
    Attached to my computer at the time was my Seagate Free Agent Go-Flex for Mac backup drive.
    So, I closed any open applications, and restarted my computer. But it wouldn't restart. It only displays a grey screen with a flashing icon in the middle of a folder with a question mark on it.
    I have no idea what happened - I wasn't using the machine any differently than usual, and it only had a few basic applicaitons open in addition to InDesign (like Preview, Text Edit, Microsoft Word, iCal).
    I have MacKeeper on my MacBook, and I keep it clean.
    Does anyone out there know what this flashing icon indicates, and if there is anything I can try on my own to fix it?
    Thanks.

    ali har wrote:
    It started while I was using Adobe InDesign, and that program froze, then crashed. When I tried to reopen the program, the error message I received was simply "Error: 16".
    I tried to take a screen shot of the error message for reference, and it gave me a message saying I couldn't because I didn't have access to the files where it would normally store the shot.
    For the Error: 16
    http://kb2.adobe.com/cps/827/cpsid_82744.html
    Seems a uninstall and reinstall of CS is in order.
    Attached to my computer at the time was my Seagate Free Agent Go-Flex for Mac backup drive.
    May or may not be a contributing factor,  may have kicked in at a wrong time or running root code.
    So, I closed any open applications, and restarted my computer. But it wouldn't restart. It only displays a grey screen with a flashing icon in the middle of a folder with a question mark on it.
    Computer can't find a bootable volume.
    https://support.apple.com/kb/TS2570
    I have MacKeeper on my MacBook, and I keep it clean.
    Well that explains it, MacKeeper is almost malware.
    http://applehelpwriter.com/2011/09/21/how-to-uninstall-mackeeper-malware/
    Search the forums here for "MacKeeper" they will tell the whole story, crapware.
    Disconnect all drives, follow the "Grey Screen" instructions and hold Shift key down while booting, if you get into OS X , immediatly backup your files to another drive and disconnect.
    In my opinion you should first check to make sure you have a backup of your data, then just erase the entire internal drive (hold c boot off the 10.6 disk, use Disk Utility), reinstall OS X, same user name, update to 10.6.8, c boot off the 10.6 and Repair Disk (to fix a update error) install your programs and finally return files from backup into the same main user folders like before (Music, Docs, Pictures etc.)
    A pain it is, but you've hosed your system and in the process you might as well rebuild everything and have a fast machine again. So happens to clear MacKrapper, uninstall CS5 and any other junk in your system at the same time. Fresh, clean, lean and mean.
    Learn to Carbon Copy Cloner to a external drive that new pristine boot drive, you can hold the option key and boot from it (even update it), which is a real bacon saver when something like this happens.  Also it's free to use, donations accepted.
    http://www.bombich.com/
    Note: if anything above I've mentioned is too complicated or your not sure, seek the services of a local computer specialist.

  • Late 2008 macbook 13" prompts mac OS can not be installed on this computer after booting from disc as l get the folder with the question mark screen. New HDD or ?

    From the little research l have done, l have been convinced l may be having a dead hard drive though after having tried all the other troubleshooting tips found here, when trying to boot l get the grey screen and folder with the question mark suggesting it can not find the files neccessary to boot hence l tried booting with the disc and the message l get is that mac OS X can not be installed on this computer, though after doing the hardware check etc they all say okay. I've even tried erasing the drive and trying to instal the OS afresh with no luck. Any ideas or l must just get a new hard drive?

    Pretty sure BGreg hit the nail on the head. If your hard drive was failing, you would still be able to at least attempt an install, provided your ard drive was mounting. You usually get that message when the disk is incompatible with the computer. If it is the proper disk, you might try erasing the disk (provided your info is backed up) using Disk Utility (under Utilities in the menubar) and choose the Mac OSX Extended (Journaled) format.

  • My MacBook Pro turns on and only shows a folder with a question mark and blinks.  The computer will not continue start-up. Suggestions/Advice?

    I'm not sure how this screen is appearing, but I tried powering up my computer this morning and it immediately presents a grey screen, then displays a blinking folder with a question mark in the middle of it.
    I am looking for troubleshooting advice and procedures to bypass this screen and allow my computer to complete it's start-up.
    Thanks-
    Gary D. Aston, Jr.
    [email protected]

    The folder with a question marks is usually an idication that the Mac can't find the system file to boot from.
    Since you never told us which system your Mac was running there is nothing more to say.
    Allan

  • IMac wont boot Past Grey Screen, finder folder with blinking question mark

    iMac G5 won't boot Past Grey Screen. The G5 froze and i restarted, It will not go past the grey screen and it has the finder folder with blinking question mark, also the fans kick on wide open. As it atempts to boot a sound plays "beepda beepda beepda beep" that starts quiet and gets louder and repeats a couple of times. I ran a hardware check on the startup disk and all hardware passed. I thought it might be the RAM any suggestions?
    I have restarted using the troubleshooting methods in the guide.

    Sorry for the late reply. The drive shows up when booting to disk, but it will not allow you to verify disk or repair. Also it will not allow you to select the hard drive to reinstall the software. Under disk utility Maxtor sabre shows up with total capacity:0 bytes.
    I've taking the Mac to the Apple store to get looked at, and its probly the hard drive. Now Im trying to see if theres a way to recover the data myself. I've used software like "Data Rescue" the hard drive shows up "Maxtor Sabre" totally capacity: 0 bytes, and it will not recover anything.
    Did this test just to see if it was power problem.
    http://support.apple.com/kb/HT2173
    Thats when noticed the beeps are coming from the hard drive. So its getting power.
    Now just wondering how to recover data.
    Any suggestions?

  • When I boot up my I get a grey screen with a flashing folder with a question mark

    I was trying to set up a bootable Linux flash drive for another computer using UNetbootin and I accidentally selected an empty partition on my hard drive instead of the USB I was trying to use. It went through the install process, and I didn't realize it was on my computer rather than the USB. The computer worked fine, so I thought nothing of it.
    Today, I go to mess with my computer and it is frozen at the login screen. I restart it, and now I just get a blinking folder with a question mark. I try to go into recovery, but it isn't there. Internet Recovery works fine, but when I go to use Disk Utility or to reinstall the OS it cannot find the internal Hard Disk.
    What am I supposed to do here? I don't want to lose all my data.

    greenbil1
    You can contact AppleCare to buy a replacement set of the oringinal Install discs for a nominal cost. You will need the serial number and a credit card to place the order.

  • How to fix a problem with my book pro that has a gray screen with a folder with a question mark on it

    does any one know how to fix a problem with my book pro that has a gray screen with a folder with a question mark on it?

    Hello Mokhtary123 and welcome to Apple Support Communities,
    It will help us diagnose your problem to know the exact model, size, year built, RAM installed and OS you're running.
    But basically your system can't find the boot disk. Usually this is a symptom of a dead/dying/corrupted hard drive;
    A flashing question mark or globe appears when you start your Mac - Apple Support
    OS X Recovery
    http://support.apple.com/en-us/HT4718

Maybe you are looking for

  • Not showing tables, views, ... in vs2010

    Hi, I installed ODP.net + ODT (11i) for use with vs2010 & oracle 10.02.0010 (to be upgraded to oracle 11). The product installed just fine, I can connect to the database using ODP and ODBC. However, when connecting with ODP in vs2010 I can't see any

  • IOException on httpURLConnection.getInputStream();

    Hello ! I have written some code to transfer a HTTP Request received on a servlet... but I'm catching an IOException when getting inputstream at the end.... I though that adding a setDoInput(true) would solve the problem but the code stops on it inst

  • IPhoto photos come up black

    When I import photos from my camera or phone to iPhoto, some of the photos come up black and I am only able to view them if I look at them through the editing feature. Please help!!

  • Iphone back ups

    Hi, when I back up my iphone (4S iOS7) to my mac, presumably it only backs up the actual data on the phone at that time (ie not any of the deleted files that may still reside on the disk), and this back up file overwrites the previous back up file, i

  • Real time Implementation scenarios

    Hi Gurus,      Can any body send me some real time scenarios on modeling i.e which DataSource used, any enhancements, which cube used ,is that BC on custom cube Plz Regards & thanks in advance, Shiv