HT1343 How do you replace the dollar key for the british pound

How to you replace the dollar sign with the british pound.

HI,
In System Preferences > Language and Text > Input Source tab choose the British Keyboard option.
8:28 PM      Thursday; August 29, 2013
  iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.4)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Similar Messages

  • How do you replace the hdd in an emac

    how do you replace the hdd in an emac

    well you need to take of the back shell to do this you will need an alen key and philips screwdriver 1. take of the ram cover of the back of the computer after you unplug all cables and leads 2.take out all alen key screws around your emac lift up the case back about 3-4 inches of and take the little cable going into the powerbutten out than take of the cover fully and put aside 3. on the side whith the computer on (the bottem) and take out fillip screws holding the plate and unclip it and take it of to revele the computer componets 4.unplug the vidio cable (top left corner of logic bord) and all cables on the left bottem and the power cable on the screen side of the computer 5 unscrew the philips screws in the bracket for the fan and power port and move outthe fand and port out of the way 6. take out all screws holding the bracket for the computer part of the emac 7.grab the top of the plate and liftup and take the computer componetns out twords yourself becouse there is a plug at the back that gives the bord power and stuff 8.on the back of the computer components is the hard drive bay and undo the two screws holding the bay in and take out undo four screws and unplug the old hardrive and put in your new one and plug that in 9. put the emac back together in reverse how you pulled it apart makeing shore that the logic bord and powerbutten are pluged backin.

  • HT4528 how do you replace the sim card on an iPhone 4?

    how do you replace the sim card on an iPhone 4?

    Click Support at the top of this page, then click Manuals

  • How do you replace the main start up drive?

    My main drive is full and I want to replace it with a larger drive. How do you go about upgrading the hard drive as a start up disk?

    danbfoto wrote:
    My main drive is full and I want to replace it with a larger drive. How do you go about upgrading the hard drive as a start up disk?
    Stick a new drive in a free bay.  Format it with Disk Utility.  And then use a backup utility like Carbon Copy Cloner to copy your current drive to the new drive essentially making them equivalent.  Then change Startup Disk system preferences to use the new drive and reboot (from your new drive) and continue on your merry way.
    Keep the original as a backup.

  • Sony CFD S300. What is the part number for the optical pick up? How do you replace the optical pick

    Hi. Apparently none of the links work on the sony site for this product (Sony CFD S300 CD Radio Cassette Recorder). Does anyone know what the part number is for the optical pick up (laser)? They have them on eay for around $10 but i do not know which one to get. Also anyone have directions on how to replace it? There is a soder ball somewhere too. Thanks!!

    Hi LifelongCamper,
    There are two Optical pickups available for the CD player. Part #s of the Optical pickups for this CD player are 882016102 and 884848312. You can purchase “882016102” from below provided link:
    https://servicesales.sel.sony.com/ecom/accessories/web/shoppingCart.do?operation=addToCart&itemId=12...
    Instructions to replace internal parts of the CD player are not made available to end users.

  • How do you find the size of a current layer so you can make other layers the same size

    When I have an PSD icon set and I want to size a layer to a size that looks good.  How do I see the dimentions of that layer so that I can select another layer and make it the same size.

    well that's my point Chris.  I have a PSD that has 150 icons in it.  I want to take 5 of them and make them the same size 300 x 300 from the 180 that they are.
    If I select one and then press Apple T, I can see that it is 180 x 180 in the info window.  I can then go to the transform bar at the top where it says 100% x 100% and type in 180px then 180px in the other.
    Chris Cox wrote:
    Or duplicate the layer and replace the contents...
    Then repeat for the other 4 layers.  Is this the correct way (easiest?)  How do you replace the layer after duplicating it.

  • How do you fix the 2 to 3 second voice delay when answering iphone 5 this is with multiple carriers and its unaceptable on a phone that cost almost 700 dollars it did not happen on my cheap prepay samsung

    how do you fix the 2 to 3 second delay on hearing somones voice when answering the iphone 5 this happens on lots of  iphone 5s with differant carriers so its not one carriers problem its probably apples this is unacceptable on such an expensive phone and very irratating. my last cheap samsung t mobile 50 dollar pre pay never did this,im new in my  contract an will take the phone back if i have to put up with this for 2 years.other than that huge problem i love the phone. i dont understand why this did not get covered like the maps problem,cause its a lot of phones and its probably an ios problem.

    Wow!
    I'm not going to be of much use regarding answers but I sure am going to watching this post like a hawk for any replies. My package is a slightly diluted version of this and I do find the BBtalk and data limits hard to make the most of as well.
    If nothing else this totally highlights how complicated BT have managed to make their packages.
    A cynic would assume that they are trying to catch us out at every step and for us to either be overspending or not really getting the moneys worth.

  • How do you change the shortcut keys for Firefox in Welsh For Mac?

    I'm using Firefox in Welsh on Mac (asking in English to hopefully get more answers), and every time I try to do the shortcut for copy (cmd+C), it hides the window (since Hide in Welsh is Cuddio, the shorcut for that is now Cmd+C). I usually forget this, and proceed with using the shortcut for copy only to anger myself when I realise that I've hidden the window.
    My question is, how do you change the shortcut keys on Firefox so then I can change the Hide shortcut and give Copy the cmd+C shortcut? I'm also using OpenOffice.org in Welsh, and they are using cmd+C for copy and cmd+H for Hide.
    Is there any way that I could do this myself? Its rather annoying for me, and its rather weird to use Cmd+X for Cutting text instead of copying.
    Thanks.

    This could be worth a bug. It shouldn't happen that some shortcut keys get (re)used for other actions and Cmd + C should be considered as one of them.
    You can try to make the change in this file: cy.jar/locale/browser/baseMenuOverlay.dtd
    <pre><nowiki><!ENTITY hideThisAppCmdMac.label "Cuddio &brandShortName;">
    <!ENTITY hideThisAppCmdMac.commandkey "C"></nowiki></pre>
    English language pack: en-GB.jar/locale/browser/baseMenuOverlay.dtd
    <pre><nowiki><!ENTITY hideThisAppCmdMac.label "Hide &brandShortName;">
    <!ENTITY hideThisAppCmdMac.commandkey "H"></nowiki></pre>
    You can find the file cy.jar in the chrome folder in the Firefox application folder.<br />
    The file cy.jar is a ZIP archive, so you need a program that can open such an archive and edit the file baseMenuOverlay.dtd.
    I'm not on a Mac, so can't do any testing in this matter. I just downloaded the Welsh (cy.xpi) language pack for Mac and had a look in it.

  • How do you change the key of a Logic Pro X loop?

    Hi everyone,
    I am working on a song in Logic Pro X using one of the loops and I just wanted to know how to change the key of the loop to fit in with the key of the song? The key of my song is C Major while the Loop is in G Major.
    Any tips would be gratefully received.
    Many thanks.

    Jamiesroom wrote:
    How do you change the key of one specific loop using the Key/Transpose in the Inspector? Step by step instructions would be great.
    Many thanks.
    Here is the step-by-step instruction:
    Step 1: Select the MIDI Region and set the Transpose value in the Region Inspector to the left.
    Step 2: There is no Step 2
    If you are a newbie, then I would recommend to have a look at my Graphically Enhanced Manual "Logic Pro X - How it Works" where I explain everything in great details with lots of easy to understand diagrams and screenshots, including a separate chapter about Apple Loops.
    BTW: If you have a proper Apple Loop, then it should automatically adopt to the key of your Project. A transpose is not necessary, unless you want to overwrite a phrase to a specific key.
    Hope that helps
    Edgar Rothermich
    http://DingDingMusic.com/Manuals/
    'I may receive some form of compensation, financial or otherwise, from my recommendation or link.'

  • Sent iphone 5 3x for repair ( 1 repair and 2 replacement ) in a span of 2 months.. And i just ask apple care to extend the warranty of my replacement iphone 5 for 6 month, i mean how can you trust the 2nd replacement if the 1st replacement didnt last long

    Sent iphone 5 3x for repair ( 1 repair and 2 replacement ) in a span of 2 months.. And i just ask apple care to extend the warranty of my replacement iphone 5 for 6 month and they reject it,  i mean how can you trust the 2nd replacement if the 1st replacement didnt last even for just 1 month? Really dissapointed!!

    No, really just want to voice out my dissapointments with apple care.. Im just really ****** off..

  • Using Configurator, you can install paid apps to a set of iPads. How do you recover the app license if one of the iPad "dies" and needs to be replaced?

    Using Configurator, you can install paid apps to a set of iPads. How do you recover the app license if one of the iPad "dies" and needs to be replaced?

    Used iMac iLife issues: Apple Support Communities

  • I just synced my iPhone and lost all the info in notes from my phone. It was replaced with whT was on my iMac how do you make the sync go from phone to desktop and not the other way around

    I Just synced my iPhone and lost all the info in notes I had on the phone. How do you have the info sync from phone to desktop and not the other way around as I usually make contact changes etc on my phone. I would then like to be able to sync that info from desktop to ipad thanks

    It does make sense.  The iPhone is a one-person device and just syncs to one computer.
    The way it should work is as follows:
    Old computer content ---> New computer
    New computer <---> syncs to iPhone
    But the way you are trying to operate sounds like:
    Old computer content ---> iPhone
    ... and ...
    New computer content <---> iPhone
    So simply move your old stuff (either directly from iTunes, or from a computer backup) to the new computer, have it all there, then sync your iPhone to the new machine.

  • How do you repair the EFI systems partitions when you mac tells you that the live file system is not supported?

    how do you repair the EFI systems partitions when you mac tells you that the live file system is not supported?

    I don't have good news. You will need to repartition and reformat the hard drive in order to determine if the drive is still OK or if it needs to be replaced. If your computer is a 2011 model or later do the following:
    Install Mavericks, Lion/Mountain Lion Using Internet Recovery
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    Boot to the Internet Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
    Partition and Format the hard drive:
    Select Disk Utility from the main menu and click on the Continue button.
    After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
    This should restore the version of OS X originally pre-installed on the computer.
    If your computer is pre-2011 model, then locate the original installer discs that came with the computer. Then do this:
    Clean Install of Snow Leopard
    Be sure to make a backup first because the following procedure will erase
    the drive and everything on it.
         1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
             with your computer.  Insert the disc into the optical drive and restart the computer.
             After the chime press and hold down the  "C" key.  Release the key when you see
             a small spinning gear appear below the dark gray Apple logo.
         2. After the installer loads select your language and click on the Continue
             button. When the menu bar appears select Disk Utility from the Utilities menu.
             After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
             size.)  Click on the Partition tab in the DU main window.  Set the number of
             partitions to one (1) from the Partitions drop down menu, click on Options button
             and select GUID, click on OK, then set the format type to MacOS Extended
             (Journaled, if supported), then click on the Apply button.
         3. When the formatting has completed quit DU and return to the installer.  Proceed
             with the OS X installation and follow the directions included with the installer.
         4. When the installation has completed your computer will Restart into the Setup
             Assistant. Be sure you configure your initial admin account with the exact same
             username and password that you used on your old drive. After you finish Setup
             Assistant will complete the installation after which you will be running a fresh
             install of OS X.  You can now begin the update process by opening Software
             Update and installing all recommended updates to bring your installation current.
    Download and install Mac OS X 10.6.8 Update Combo v1.1. You can now download a version of OS X from which to upgrade from your Purchases page in the App Store.

  • How we can replace the column in Core Table plz see this msg

    Hi,
    How we can replace the column in Core Table plz see this msg
    Req:
    when i push the Insert button the data inserted into the Table
    like
    Cols Values
    FOCD      CUFZ14
    PRDCD FU6
    Month 082008
    AgencyCD AG02
    PLAN 123
    This is FO_Plan Table....
    Requirement:
    i need at table show to replace the Prd_CD to Prd_Desc while inserting the above Row....
    There is no Prd_Desc in FO Plan Table....
    Prd_desc comes from Product Table.
    did u get my point...
    how to solve.
    Thanks
    Ram
    Edited by: Ram Vungarala on Sep 24, 2008 9:09 AM
    Edited by: Ram Vungarala on Sep 24, 2008 9:15 AM

    Hi,
    I'm not sure if I understood what are you trying to do. But you can modify your table in a backing bean code. JSF page code for a table:
    <af:table id="product_search_results_tbl" binding="#{backingBean.boundTable}" ... />
    And a backing bean code:
    import oracle.adf.view.faces.component.core.data.CoreTable;
    public class YourBackingBean {
        private CoreTable boundTable;
        public void setBoundTable(CoreTable boundTable) {
            this.boundTable = boundTable;
        public CoreTable getBoundTable() {
            return boundTable;
       public String insertButtonAction() {
          // Bind your button action to this method and modify here your bound table
         return null;
    {code}
    Look for column modification methods in a CoreTable class documentation.
    Marius                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                               

  • How can I replace the cursor in the below query?

    I have this below query which calls a stored procedure that takes only 1 item's attributes at a time. But because of performance problems we are
    required to remove the cursor. How can I replace the below cursor logic with set operations or CTE? Please advice.
    DECLARE db_cursor_ava CURSOR
    FOR
    SELECT t.[agent-id],
    t.[start-date],
    t.[end-date],
    t.[monitor-days],
    t.[monitor-start],
    t.[monitor-end],
    t.[timezone-offset]
    FROM @tmpAgentPeriodTimeRange t
    OPEN db_cursor_ava
    FETCH NEXT FROM db_cursor_ava INTO @agentID_ava,
    @stDateTime_ava,
    @endDateTime_ava,
    @monDays_ava,
    @monSt_ava,
    @monEnd_ava,
    @offset_ava
    WHILE @@FETCH_STATUS = 0
    BEGIN
    DELETE
    FROM @tmpMonitorPeriod
    DELETE
    FROM @tmpFinalResult
    SET @runID = 1
    IF(@endDateTime_ava>DATEADD(MI,@offset_ava, GETUTCDATE()))
    BEGIN
    SET @endDateTime_ava=DATEADD(MI,@offset_ava, GETUTCDATE())
    END
    INSERT INTO @tmpMonitorPeriod
    EXEC core.usp_GetMonitoringPeriod
    @startDate = @stDateTime_ava,
    @endDate = @endDateTime_ava,
    @monitoringDays = @monDays_ava,
    @monitoringStart = @monSt_ava,
    @monitoringEnd = @monEnd_ava
    SELECT @maxID = MAX(tm.id)
    FROM @tmpMonitorPeriod tm
    FETCH NEXT FROM db_cursor_ava INTO @agentID_ava,
    @stDateTime_ava,
    @endDateTime_ava,
    @monDays_ava,
    @monSt_ava,
    @monEnd_ava,
    @offset_ava
    END
    CLOSE db_cursor_ava
    DEALLOCATE db_cursor_ava
    mayooran99

    You've been down this path before  - and the response is exactly the same.
    how to replace cursor logic
    And I'll suggest that you post the entire code - since you repeatedly delete 2 table variables but only populate one. The setting of @maxID also seems to have no purpose. And perhaps the issue here isn't the cursor but the general approach.  Who knows
    - but it appears you may have prematurely assumed that the cursor is the problem.

Maybe you are looking for