HT1349 I have lost sound. It's ok with headphones and the ring tone works but otherwise no sound. I've restarted, checked the mute lock and bottom of page when right swiped etc and all no good. Any ideas
I've lost the sound on my I pad 2. It works ok with headphones but not without. Mute is definitely not on. Have restarted and reset. Any other ideas?
See this link - http://support.apple.com/kb/HT4085
Others have reported exactly like you but have since found that settings had changed!
Similar Messages
-
my daughters ipod 4th gen will no longer charge past 20% and will not connect to a pc in order to back everything up. the cable is working fine, otherwise it would not even charge to the 20%. i have tried the reset to not lose any data and no luck, home+power for 10-15 seconds. I really would like to not lose everything she has, again, because I can't back it up this time. I have tried charging via a wall outlet and PC and both charge fine, just only to 20%. I am using the cable that came with it so no aftermarket issues there. Please help so I don't have to reset everything again.
Because once it has charged enough to be powered on as soon as you turn it on it says battery is at 20% and will not charge anymore after that, it just runs for about 5-10 minutes before the battery dies again. The battery cycles discharge/recharge daily and its not on the charger at full charge for more than a couple hours and is never totally dead for more than a couple of hours.
-
Hi, I have a frustrating problem that seems to have occurred post iOS 8 installation. When my iphone5 is switched off the ring tone fails to sound i only get the vibration. If i am using my phone and a have an incoming call then the ring tone works as normal. I think it has something to do with "do not disturb" ... i see from the menu in "do not disturb" that under the heading "silence" there are two options "always" and "only when the phone is locked" This does not seem to make sense as i have to choose one or the other!
If anybody can help advise me on this problem i would be very grateful.
ThanksHello Mogulman46,
So what that means is when you have Do Not Disturb turned on, you may have an alert depending on the setting and how you are using your iPhone. So if it is set to Always, then that means that no matter what, your iPhone will not be notified. If it set to Only while the iPhone is locked, then that means that you will not get notification when your iPhone is locked but you will get notifications if your iPhone is being used. Also keep in mind the settings All Calls From can be set to certain contacts like Favorites, Everyone or no one. If you are using Do Not Disturb and you do not need it, then turn it off.
Use Do Not Disturb on your iPhone, iPad, or iPod touch
http://support.apple.com/kb/ht5463
Regards,
-Norm G. -
I have been buying apps for a long time without a problem using my credit card on file. All of a sudden itunes is not recognizing my card which is in good standing. All the info is correct but itunes/apple says it doesn't match the bank info. Any ideas?
Answered in your Other post on this Topic...
https://discussions.apple.com/message/24053626#24053626 -
I want to sync tasks in Outlook with my iPhone. I have tried Toodledo (not good) and Todo. Todo works, but it cuts off most of the text. I only get the beginning of my (long) lists. Any ideas how I can solve this problem? I starting to regret that I switched to iPhone...
Usually if you have some kind of hardware failure there is some beeping during POST or most motherboards now have LED indicators to produce and error message based on the type of failure
So if its bad memory, not place properly, mismatched, processor not inserted properly, mismatched voltage or voltage connector not present etc it beeps or generates the error id.
Power supplies can be tested for failure. There are some walk throughs for testing just them with a switch, paperclip or a jumper (I'd suggest not doing this if you are not familiar with the dangers of electricity).
Memory can be tested with memory diagnostics programs like Memtest+
Processors can overheat if the proper precautions have not been taken usually you will get a POST beep or error code for that.
If the motherboard has no response then do the basics first:
Check power connectors and power supply. Once you determine that is not the case move on to other items like graphics cards in all the way or memory. -
The volume on my iPad 3 has gone. I've checked the mute button, tried restarting, resetting etc and nothing has changed. I can't hear the music, hear any sound from videos. Most times the video stops playing after a seconds. My iPad 3 is only 2 months ol.
If you have lost all sound and video is freezing on you, that ain't good. Your iPad is two months old so I would not hesitate to contact Apple at all. You are entitled to 90 days of phone support.
http://www.apple.com/support/ipad/contact/.
If you want to try a couple of things on your own, try quitting all apps and then reboot the iPad - not so much for the sound issue itself - but more as a general "start all over again" sort of approach. It might help with the video freezes.
Go to the home screen first by tapping the home button. Double tap the home button and the task bar will appear with all of your recent/open apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar. Reboot the iPad.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
If you use headphones on occasion, you can try plugging and unplugging those as well and see if the sound comes back.
You could even try restoring the iPad to factory settings and then restore from a backup, but unless there is something totally hosed on the iPad, that should not be necessary with a two month old device - of course assuming that you didn't drop the iPad or do something accidental that could be causing the problems. -
In "edit" mode, my movie speed is fine. Once published it seems to slow down and become all jerky. Any ideas? Thanks
I have a revision a imac g5 with the same problem with only macbreak podcast. I know leo laporte said that the podcast was done in 1080p and my computer with its built in 64 megabyte graphics card might have trouble with this podcast but your machine must have a better graphics card than mine. 1080p requires at least 128 megabytes of graphics memory built in. My machine played this podcast on quicktime fine until they came out with the update to quicktime last week or two ago. I was going to upgrade my memory until I came accross your story and your machines doing the same thing with much better specs. I think it might be the quicktime update that is causing a problem. Maybe Leo will talk about this problem since he is doing a mac show about macs.
-
Have copied my iTunes library back-up from my external hard drive (saved from my iTunes on my pc) onto my new Macbook and loads of the tracks have been duplicated, some four times some not at all?? any ideas guys?
Have copied my iTunes library back-up from my external hard drive (saved from my iTunes on my pc) onto my new Macbook and loads of the tracks have been duplicated, some four times some not at all?? any ideas guys?
-
States the account cant be used or the password and such is wrong. I noticed that after google bought youtube it all became complicated. Tried all trouble shooting, Any ideas?
That would indicate an issue with the local network, not internet. This can impact devices differently and will likely be more obvious on a streaming only device.
If you are on wifi try ethernet
Make sure DNS is set to auto (settings - general - network)
Go to istumbler, netstumbler or similar to get a report of the network, look for signal strength and noise. -
i know this sounds weird but i went to Cleveland from florida and when i returned Siri has an australian accent. any ideas?
Well you can't use it. The iOS 7 Activation Lock is pretty secure and you can't bypass it.
-
I have 2 apps that have been waiting to update for a week. I don't really care about the update, I would just like to use them, but the are stuck waiting. I have tried powering down, syncing with my computer...all fails. Any ideas?
At this point you have no choice but to update the or delete them and reinstall them since you wont be able to use them until they update - or come out of the "waiting" loop.
Make sure that you do not have a stalled download in iTunes - a song or podcast .... if you have a download in there that did not finish, complete that one first. Only one thing can download at a time on the iPad so that could be what is causing the problem.
If that doesn't work - sign out of your account, restart the iPad and then sign in again.
Settings>Store>Apple ID. Tap your ID and sign out. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Go back to Settings>Store>Sign in and then try to update again. Tap one waiting icon only if necessary to start the download stream.
You can also try deleting the waiting icons - tap and hold down on an icon until it wiggles - the tap the X on the icon to delete it. Then try to download again.
You can try resetting all settings. Settings>General>Reset>Reset All Settings. You will have to enter all of your app preferences and device settings again. -
Can't get itunes updates on ipad, but can get everything else...genius, purchases, etc. When I select "updates" screen is blank. Any ideas??
The update server is down; try this temporary workaround
App Store>Purchased>Select "All"
Note: Look out for apps that have the word "Update"
http://i1224.photobucket.com/albums/ee374/Diavonex/9c256282736869f322d4b3071bbb2 a82_zps51a6f546.jpg -
I set up a new PIN to lock my screen for security. Now I can't unlock it. Any idea how to undo this so I can use my phone again?
Someone else had replied with that same remedy and if that's all it takes, no worries. However, it is tellig me that after 10 unsuccessful tries it will reset my phone back to zero and I lose everything...pictures, emails, texts,etc. Is this true or not...do you know? Thanks.
-
I have an 8 year old eMac G3. It will not start up. I need to erase it before putting it in recycling. Apple refuses to open the case and warns me that I will be shocked if I even try. They say no way to erase hard drive. They say use a hammer. Any ideas?
Hi, no eMacs had G3s, only G4s. Is it maybe an iMac G3?
If you don't know the model, find the Serial# & use it on one of these sites, but don't post the Serial# here...
http://www.chipmunk.nl/klantenservice/applemodel.html
http://www.appleserialnumberinfo.com/Desktop/index.php
How to find the serial number of your Apple hardware product...
http://support.apple.com/kb/HT1349
http://www.ifixit.com/Device/eMac -
I dropped my iPhone 4 in the sink where it was submerged in water for not even 2 seconds I took it out and put it in a warm room by the radiator and most of it works but no sound and battery length is short and runs out quickly. Any ideals on how to help?
$149
They do not repair .Apple exchange and all returned units are refurbished at The Apple plants in China
So you get a device that looks like and functions like new
Are you familiar with the results of water and electricity mixing
Maybe you are looking for
-
Trying to update my iPhone 5 iOS 6.1.4 to the new iOS 7 and it says my software is up to date. Please help. Are the servers just down?
-
Nikon D5200 and Camera RAW help
Elements 11 with updated Raw still doesn't read my the files from a new Nikon camera.
-
Photosmart Premium C309G not printing in black
I've replaced the black ink when I noticed the printing started to fade and the levels were low. The new cartridge did nothing. The page I was trying to print had black letters with a light blue shading behind it. The light blue turned a light gray,
-
How to migrate services from old server before shutting down
We have six servers at my workplace, and we're looking to retire one server. I need to migrate all services from the old server before we can fully turn it off. How would I go about doing that ? Can't get access into the old server, but I believe it'
-
Hello All- In this short screencast, it's difficult to tell, but you can see a clip that is set to play at 100% normal speed, playing back as if it's sped up, or dropping frames maybe. I've deleted the clip in the Event browser and re-imported, I've