HT1386 connection could not be established to the iphone
Hi
I have a problem when I sync my phone. a message show "itunes could not sync information to the iphone because connection could not be established to the iphone" Please help.
I am also getting this error with two iPad 2s and an iPhone 5. All are on iOS 6.0.1 and this is with iTunes 11 on a Windows 7 PC. I also have an iPhone 4 that does not seem to have an issue that I can tell. When I plug in the iPhone 5 and one of the iPads, it will start to to sync and right at the end I get that message. It will, however, still continue to sync the device after the error message pops up. With the one iPad, which is rarely connected to computer, it will find the iPad via wifi when iTunes is opened, but I will get that message when it is performing its initial sync.
While I kept having sync issues when using iTunes 10.7, this is a new issue for me. I was also getting a lot of warnings that the iPhone or iPad could not be synced because the connection was lost even though the iPad and iPhone were connected via USB cable. In those cases, the sync would just abort. I have not gotten that error though in two days. At the time to resolve that issue, I needed to disconnect the USB cable, reset the iPhone/iPad, and then reconnect the USB cable.
I really wish Apple would figure out these sync issues.
- Merg
Similar Messages
-
Itunes could not sync because a connection could not be established to the Iphone
I have been trying to sync my 4s and I keep getting "Itunes could not sync because a connection could not be established to the Iphone"
I am also getting this error with two iPad 2s and an iPhone 5. All are on iOS 6.0.1 and this is with iTunes 11 on a Windows 7 PC. I also have an iPhone 4 that does not seem to have an issue that I can tell. When I plug in the iPhone 5 and one of the iPads, it will start to to sync and right at the end I get that message. It will, however, still continue to sync the device after the error message pops up. With the one iPad, which is rarely connected to computer, it will find the iPad via wifi when iTunes is opened, but I will get that message when it is performing its initial sync.
While I kept having sync issues when using iTunes 10.7, this is a new issue for me. I was also getting a lot of warnings that the iPhone or iPad could not be synced because the connection was lost even though the iPad and iPhone were connected via USB cable. In those cases, the sync would just abort. I have not gotten that error though in two days. At the time to resolve that issue, I needed to disconnect the USB cable, reset the iPhone/iPad, and then reconnect the USB cable.
I really wish Apple would figure out these sync issues.
- Merg -
I thought I would restore my iphone so I backed it up and everything it backed up fine.
It will put the firmware on the phone fine it also syncs but it come up and says warring it didn’t sync the number of apps. Then I press ok then I get this.
iTunes could not sync information to the iphone because a connection could not be established to the iphone
When I re plug in the I phone in it shows it the data synced but it’s all other
It’s just a 8 gig I phone
I up dated to windows 7 so I thought that was it so I tried it with windows xp the same thing happened
And the newest I tunes would a older I tunes workI thought some screen shots may help
The first one is at it syncs you can see at the bottom the apps are green and the other is yellow like it should be.
this one is after it syncs and the frist Warning notice the other now
warn #2
warn #3
and the i phone -
This is a new problem for an IPod Touch I have had for a year. The IPod is hooked up by cable and appears in ITunes. I can examine all the content on the IPOD and I can click "sync". It goes through to Step 7 and then the error messages occur. First "a session could not be started with the IPod" and when that dialogue box is closed, the message "a connection could not be established to the IPod."
Maybe:
Sync Session Failed to Start iTouch iOS5: Apple Support Communities
iphone could not be synced sync session failed to start...: Apple Support Communities -
HT1386 connection could not be established from itunes to ipad mini
I'm having trouble getting itunes to start a session with my ipad mini. I've turned off the ipad, disconnected, and restarted, but it still doesn't connect. Itunes see's the device, however when I select Sync, or apply, I get the following messages: itunes could not back up the ipad beacuse a session could not be started with the ipad, and then I select "ok". Another message comes up: itune could not sync information to the ipad because a connection could not be established to the ipad. What to do?
I am also getting this error with two iPad 2s and an iPhone 5. All are on iOS 6.0.1 and this is with iTunes 11 on a Windows 7 PC. I also have an iPhone 4 that does not seem to have an issue that I can tell. When I plug in the iPhone 5 and one of the iPads, it will start to to sync and right at the end I get that message. It will, however, still continue to sync the device after the error message pops up. With the one iPad, which is rarely connected to computer, it will find the iPad via wifi when iTunes is opened, but I will get that message when it is performing its initial sync.
While I kept having sync issues when using iTunes 10.7, this is a new issue for me. I was also getting a lot of warnings that the iPhone or iPad could not be synced because the connection was lost even though the iPad and iPhone were connected via USB cable. In those cases, the sync would just abort. I have not gotten that error though in two days. At the time to resolve that issue, I needed to disconnect the USB cable, reset the iPhone/iPad, and then reconnect the USB cable.
I really wish Apple would figure out these sync issues.
- Merg -
I keep getting a 'connection could not be established with this iPhone' message when I try to sync, even thos I can see my iPhone 5 in iTunes & have tested the link by manually transferring songs from iTunes to the iPhone. Can anyone help?
I am also getting this error with two iPad 2s and an iPhone 5. All are on iOS 6.0.1 and this is with iTunes 11 on a Windows 7 PC. I also have an iPhone 4 that does not seem to have an issue that I can tell. When I plug in the iPhone 5 and one of the iPads, it will start to to sync and right at the end I get that message. It will, however, still continue to sync the device after the error message pops up. With the one iPad, which is rarely connected to computer, it will find the iPad via wifi when iTunes is opened, but I will get that message when it is performing its initial sync.
While I kept having sync issues when using iTunes 10.7, this is a new issue for me. I was also getting a lot of warnings that the iPhone or iPad could not be synced because the connection was lost even though the iPad and iPhone were connected via USB cable. In those cases, the sync would just abort. I have not gotten that error though in two days. At the time to resolve that issue, I needed to disconnect the USB cable, reset the iPhone/iPad, and then reconnect the USB cable.
I really wish Apple would figure out these sync issues.
- Merg -
HT1386 session could not be started with the iphone
I cannot get my iphone, ipad and itouch to sync or back up anymore ?
Hi dslep,
This article addresses backup issues, including an error that references being unable to start a session:
iOS: Troubleshooting backup issues in iTunes
http://support.apple.com/kb/ts2529
Cheers,
- Ari -
The only history I could find on this problem is at http://discussions.apple.com/thread/2059115?threadID=2059115
'iTunes could not sync information to the iPod "device name" because a connection could not be established to the iPod'
I have an old iPod Touch, for which the most recent compatible OS seems to be 3.1.3. iTunes is quite new (iTunes 10.3.1.55) on Windows 7 Profession 64-bit. Has everyone else who has had this problem on an old iPod Touch found that it was solved, or do they just ignore it?You will not lose data doing a reset.
If this does not work, maybe try to use a second user account, disable autosync in iTunes, plug in, right click on it in the device list and choose "backup". This will create a backup without syncing.
If the backup goes through, transfer purchase the same way.
Set up at least on contact and event for that new account, let iTunes erase the device and restore from the backup you made before.
If it works for the second user account, there's something wrong on the other side, maybe a defective backup or iTunes. -
I cannot sync my iTunes library to my iphone5 can you help I get error message a connection could not be established to the iPhone
Yes it is.
Initially I got an error message saying can't connect because of Date & Time settings.
Went in and re-verified that those were correct.
Tried to update downloads and then got a new error message: "Can't connect to iTunes Store".
I live in the US and that's where I created my iTunes a/d and Apple ID.
I am currently in India --- can that coause confusion re date & time? -
A connection could not be establishe​d...
Hi, i am undergraduate junior student who just joined a summer research lab where I need to use labview and fpga; however, all previous members all graduated last semester so there is no one who can teach me labview and what they were doing....(I really need help..)
The first problem is whenever i try to run a FPGA code the previous people made, i get : "A connection could not be established to the specified remote device. Ensure the device is on an accessible over the network, that NI-RIO software is installed, and that the RIO server running and properly configured."
In the lab labtop, there are
Labview 2012 SP1 (32 bit), NI-RIO130, Labview Real Time 2012 f1, NI-RIO FPGA driver.... and maybe some files I can't find in this messy disordered labtop.
I have CRIO-9113, NI-CRIO9022, NI-9234, NI-9269 (all four are connected, and power is green on and connected to this labtio.)
Later, i found same probelm when I try to add device on Project Explorer (FPGA Target -> new -> c series module -> "A connection could not be established to the specified remote device. Ensure the device is on an accessible over the network, that NI-RIO software is installed, and that the RIO server running and properly configured.")
Can anyone tell me why there is connection error?Hey rhksgud92,
With CompactRIO, you have to specify an IP address to connect to and program the target. In MAX (Measurement and Automation Explorer), expand the 'Remote Systems' category in the left pane and your cRIO should be located on that list. Select it, and then view the 'Network Settings' cetegory in the middle pane. Here you should see an IP address listed for your target.
Copy this IP address and open your LabVIEW project. In the project tree, right-click on the cRIO and select 'Properties'. In the windows that pops up, you should see an entry field for the IP address. Paste the value from MAX here (and make sure that it is still formatted correctly). Now you should be able to right-click the cRIO in the project and select 'Connect' with success.
I agree with Hooovahh that you are going to have a steep learning curve trying to use LabVIEW and CompactRIO for the first time without training. To make it a little easier, we do have some resources that can help you. First, since you are a student, if your school has an active Academic Site License (ASL), you can get free access to all of NI's self-paced online training resources. If you aren't sure if you have an active ASL, just ask your professor or IT division that handles your school's LabVIEW licensing. Since you are so new, I highly recommend you start with LabVIEW Core 1 & 2, and then proceed to Real-Time 1 and FPGA to learn how to use your CompactRIO.
If you don't have an active ASL, you can still follow some of the video tutorials for students for both LabVIEW and RIO, which should help you out quite a bit. Check out the link below. Lastly, I recommend becoming very familiar with the CompactRIO Developer's Guide (also linked below). This guide is a great resource for how to implement many different features and architectures in RIO applications, for both RT and FPGA.
Academic Online Training:
http://us.ni.com/academic/training
NI LabVIEW for CompactRIO Developer’s Guide:
http://www.ni.com/pdf/products/us/fullcriodevguide.pdf
Regards,
Ryan -
ESB Server connection could not be established via Jdeveloper or using ant
When I try to deploy a ESB project using ant in a remote virtual linux machine
via command mode,I am getting deployment failed message as below suggesting to check whether ESB server is running.
./ant outputs the following:
Buildfile: build.xml
deployProjects:
[echo] deploying esb project files
[deployESBProjects] Deployment Failed ...Check if server at 132.146.44.93 is running
[deployESBProjects] ESB Project </data/ESB_Samples/CPL_US_001> successfully deployed
[echo] esb project files deployed
BUILD SUCCESSFUL
Total time: 0 seconds
./opmnctl status -l oututs the following:
Processes in Instance: SOA_NFT.RHEL4AS
-------------------------------------------------------------------------------------------------------+------
ias-component | process-type | pid | status | uid | mused | uptime | ports
-------------------------------------------------------------------------------------------------------+------
OC4JGroup:default_group | OC4J:home | 1051 | Alive | 1610238535 |3616 | 20:41:30 | jms:12601,http:8888,rmis:12701,rmi:12401
ASG | ASG | N/A | Down | N/A | N/A | N/A | N/A
HTTP_Server | HTTP_Server | 1050 | Alive | 1610238534 |1820 | 20:41:20 | https1:4443,http2:7200,http1:7777
./opmnctl status -app outputs the following:
Applications in Instance: SOA_NFT.RHEL4AS
application type: OC4J
pid | name | state | rtid | classification | routable | parent
1051 | hw_services | started | g_rt_id | internal-BPEL | true | orabpel
1051 | ruleauthor | started | g_rt_id | internal-Rules | true | default
1051 | system | started | g_rt_id | external | true |
1051 | WSIL-App | started | g_rt_id | internal | true | default
1051 | orainfra | started | g_rt_id | internal | true | default
1051 | datatags | started | g_rt_id | internal | true | default
1051 | orabpel | started | g_rt_id | internal-BPEL | true | default
1051 | gateway | started | g_rt_id | internal-WSM | true | default
1051 | rulehelp | started | g_rt_id | internal-Rules | true | default
1051 | ccore | started | g_rt_id | internal-WSM | true | default
1051 | policymanager | started | g_rt_id | internal-WSM | true | default
1051 | default | started | g_rt_id | external | true | system
1051 | esb-rt | started | g_rt_id | internal-ESB | true | esb-dt
1051 | ascontrol | started | g_rt_id | external | true | system
1051 | coreman | started | g_rt_id | internal-WSM | true | default
1051 | esb-dt | started | g_rt_id | internal-ESB | true | default
1051 | javasso | started | g_rt_id | internal | true | default
Also when I try to create Appliocation Server connection using opmn port 6003 from my local Jdeveloper,the test connection fails.
While creating Application Server connection in Jdeveloper, the connection Test succeeds when I select Standalone server and
using RMI port 12401.Maenwhile, the Integration Server connection using the above Application Server connection created and port 8888 when tested
displays
Application Server: OK
BPEL Process Manager Server: OK
ESB Server: FAILED
ESB Server failue detail: ESB connection failed.
ESB Server connection could not be established.
The SOA was installed in silent mode after resolving many issues detailed in SR 6622260.992Can you try changing the port to 80 while creating connection.
-
My 2nd generation ipod touch is giving me the following error when I try accessing Itunes or the app store. "Cannot connect to the Store. A secure connection could not be established. Please check your date & time settings" I am on a secure networkl.
Can't connect to the iTunes Store
Make sure that time zone is correct in addition to date and time -
I keep getting "the network connection could not be established" message when trying to update my iPad, iPad2 and iPhone4 devices using either my iMac or MacBook. The Macs and iOS devices are apparently working correctly otherwise. Problem started about a day ago when I connected one of the iPads to my iMac and iTunes notified my of an update for the device. I tried and got the above message. Tryied other iPad2 and iPhone4 and get the same message. Also, get same message when trying to update using the MacBook. My system SW is 10.7.3 on the iMac and 10.6.8 on MacBook. iTunes is version 10.6. Have gone thru the check list of things to check and have re-started. Would appreciate any ideas. Thanks.
Another user named Springbk posted a fix that worked for me as I was having the same problem today:
I Changed my DNS settings to OpenDNS
On a Mac go to SYSTEM PREFERENCES>NETWORK>ADVACED>DNS
change DNS by adding ( + )
208.67.222.222
then
208.67.220.220
click okay/apply after. then try the update. after the update, just delete the two open DNS server numbers. should revert back to your old one. -
I keep getting the following error messages on my Mac when I try to redeem a song code: "We could not complete your iTunes store request. The network connection could not be established. There was an error in the iTunes store, please try again later." and then, "We could not complete your iTunes Store request. An unknown error occurred (-50)."
Hello, constance132.
Thank you for visiting Apple Support Communities.
Here are some troubleshooting steps that I could recommend when receiving error -50.
"Error -50," "-5000," "8003," "8008," or "-42023"
These alerts occur due to timeouts or conflicts trying to write a file during download.
If you encounter this issue while accessing iTunes Store:
See iTunes 9: "One Moment Please" or "Error (-50)" message when accessing iTunes Store
If you encounter this issue while while downloading something from the iTunes Store:
Delete your iTunes Downloads folder, located in:
Mac OS X: ~/Music/iTunes/iTunes Media/Downloads Note: "iTunes Media" may appear as "iTunes Music. Also, the tilde (~) refers to your Home directory.
Windows Vista: \Users\username\Music\iTunes\iTunes Media\Downloads\
Windows 7: \Users\username\My Music\iTunes\iTunes Media\Downloads\
Windows XP: \Documents and Settings\username\My Documents\My Music\iTunes\iTunes Media\Downloads\
After locating your iTunes Downloads folder:
Quit iTunes.
Delete the Downloads folder on your computer.
Open iTunes.
Choose Store > Check for Available Downloads.
Enter your account name and password.
If you encounter this issue while while downloading Digital Copies using Windows:
Use MSCONFIG (directions for Windows XP and Windows Vista/Windows 7) to disable conflicting software.
If using MSCONFIG steps resolves the issue, you may want to use the System Configuration Utility to turn on the third-party System Services and Startup Items one at a time (restarting your computer after turning on the item or items) to identify which System Service or Startup Item is causing the conflict.
You can turn all of them back on by selecting the Normal Startup option under the General tab of the System Configuration Utility window, but please note that this may cause the issue to reoccur.
If you are able to isolate the issue to a particular third-party software, you may wish to contact them to let them know of the conflict.
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
Cheers,
Jason H. -
I have been trying to update my iPhone4s' software from version 5.0.1 to version 5.1. I continue to get a message from iTunes that a network connection could not be established. I was buying apps for my phone on my computer so I know that my connection is good. I clicked on Help in iTunes and had it to run a network diagnostic and all was good. Are the servers just jammed up with so many people trying to update to the newest software version? Thank you in advance for your time!
Sincerely,
PrettyinPinkInklook around the forum tons of people repport that they can't update
makes you suspect that apples update servers can't meet the depand of too many users
trying to update at once
Maybe you are looking for
-
Multiple instances on single server
Hi all, I have a Solaris 10 server with 2x dual core CPU's. I am wondering if it was at all possible to install Business Intelligence Server on this single OS twice? And if it is, can I split the CPU between the different instances? The reason for th
-
Problem with entering iframe adress
again this has to do with simple viewer. as when i paste the folder under my iDisk/Web/Sites/ how do i enter the correct adress into the page.html to find the index of the slideshow folder?
-
Please help ive formatted my laptop and was able to restore some of the drivers but couldnt find the VGA drivers and the sleep on from the start button is deactivated , when connecting my laptop to a projector it doesnt show the picture. please assis
-
Solaris 10 Kernel memory usage
We have a 32 GB RAM server running about 14 zones. There are multiple databases, application servers, web servers, and ftp servers running in the various zones. I understand that using ZFS will increase kernel memory usage, however I am a bit concern
-
Hi Champs, I am trying to configure Two Step Intercompany Pricing but it seems I am missing some configuration. The scenario is we have two company codes CC-1--> Always Procures Articles for CC-2 DC belongs to CC-1 and Store Belongs to CC-2. Please a