HT1551 the led light keeps blinking after restarting it

The apple tv light keeps blinking after restartin it with remote.

You will need to restore it on a computer using iTunes.
Apple TV (2nd and 3rd generation): Restoring your Apple TV - Apple Support
Scroll down to the section titled:If your Apple TV still does not respond or if you were unable to follow the above steps

Similar Messages

Hi, My Apple TV 1st generation is showing the apple logo and the amber light keeps blinking, after a while it shows a little Apple TV with a question mark blinking on top, any ideas?

Well my question says it all. I wasn´t using the apple tv, but noticed that the amber light started to blink, so I put it on the tv and there was the apple logo. I did the recory with the "MENU" + "-" button, but came back the same. After a while it showed a little Apple TV image with a "?" mark blinking on top. I disconected it the whole night but today is doing the same. Is like it got stuck on the restart. Can anyone help me?

Fixed it after trying everything listed here with no success.
First you will need to make sure you have the ability to connect your ATV box directly to your router via a cable. This issue is directly related to networking from my experience and once connected to wifi you will have a nightmare of a time to complete the fix.
1. Make sure you have NO network connection to the ATV box.
2. Hard reboot ATV using remote (aim remote at device and hold "menu" and "down/minus" until amber light blinks)
3. When ATV reboots to a diagnostic menu select "Factory Restore"
4. After Restore has completed select a language
5. You cannot skip the the wifi selection screen without setting up a connection, however: DO NOT SETUP WIFI! Instead plug in the direct cable to your router, and hit the menu button on your remote. You will see "connecting to network."
6 Once you are past the start up splash video you will eventually arrive at the connect to itunes screen which will start looping the apple logo and a new code about every 2 seconds. Disconnect the network cable.
7. After a few seconds the loop will stop. Press the menu button to skip the itunes connection (you will be able to do it later.)
8. At the following menu go to Settings > Screen Saver > Set delay for "Never"
9. Go back to the main menu, then go to Settings > Network > Configure TCP/IP > Click on "Using DHCP"
9. Click "Done"
10. Connect cable to router, and then proceed with updating your ATV.
After I was updated the problem did not return.
I have completed this solution personally twice on the same unit. After getting updated and stable, I recovered my ATV again, and had the same problems again. Repeated these steps and good to go.
Hope this helps someone, and good luck!

HT1551 after finish installing an update, the the status light keeps blinking and a picture of the connection between the micro USB and iTunes shows up - what is this about?

after finish installing an update, the the status light keeps blinking and a picture of the connection between the micro USB and iTunes shows up - what is this about?

The update failed - using a USB to microUSB lead (that Apple annoyingly don't include!), try to restore the AppleTV software to current version software using instructions here:
http://support.apple.com/kb/HT4367
Pay attention to differences in power connection depending on whether or not you have AppleTV2 or AppleTV 3.

I have an old office deskjet 1220c - the led's keep blinking & it won't grab the paper - help

I am trying to set up an old HP Deskjet 1220C and the LED's are blinking, saying there is a paper jam, but there is no paper jam. I have made sure that the back cover is locked, cleaned all the rollers, etc, but it still won't stop blinking. Any helpful suggestions would be appreciated. Thanks!
This question was solved.
View Solution.

The page here may help with the paper feed issues. Also open the lid with the power on and make sure the carriage moves to the "smiley face" position, look at the icons on the upper back portion of the printer as shown here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

How come the pagedisplay toolbaricons keep disappearing after restarting Adobe Reader XI?

While I'm using Adobe Reader XI I've noticed that my pagedisplay icons (fit width and fit page) in the toolbar aren't there. When I reset my toolbar (alt + f8) the icons pop up, but when I restart Adobe Reader they are gone again.
Does anybody know how I can keep them locked onto the toolbar?
Your help is very much appreciated...

Do you have Creative Cloud subscription? I don't think Creative Suites are a part of it, though I might be wrong - the individual applications in the suite, yes - the full suite as one item, no. If you purchased CS6 Master Collection, not the Cloud, then you should be downloading that thru the following page...
CS6 - http://helpx.adobe.com/x-productkb/policy-pricing/cs6-product-downloads.html

I am having problems reestablishing my Time Capsule. I had to get a new internet modem and that seemed to screw up my Time Capsule. The amber light keeps blinking and it's not being picked up when my Macbook scans or when my PC scans for the wireless ne

I can't find my Time Capsule on my networks anymore. It's like it doesn't exist. We got hit by a storm and that might have caused our internet modem from ATT to fry. I replaced the modem today but now my Time Capsule isnt working. It's blinking amber. The PC its connected to through the ATT modem isn't finding it as it scans and its not in utilities. My MacBook isn't finding the time capsule either when it scans. Whenever I hooked up all the wires to the time capsule and the modem, the internet stops working. I've tried resetting the time capsule but it's still blinking. I had all my computer equipment on a power surge protector. A pretty good one. All my other equipment is fine. The ATT modem was old, so I thought it might not have even been the lightening. Nothing else in home was injured by storm. I am freaking out and need help!!! I can't use my MACbook to do my internet work and all my files were backed up on the time capsule.
Another problem. My Time Machine isn't backing up now either. What is up with that?
I would be soooo grateful if someone can help me! Thanks a million!

A PC can have more issues connecting than a Mac.
But it really should not matter.. so just try it in situ.. press and hold the reset.. once it starts up, it will return to default IP, 10.0.1.1 the PC should then be able to find it via the airport utility.
If not drag it over to the Mac and plug in there by ethernet.. or since it is a laptop, really should not be that difficult to drag the Laptop and plug it into the TC.
Important thing is to get access to the TC.
The Mac if it is running lion, then you MUST download and install 5.6 airport utility to do anything useful.
http://support.apple.com/kb/DL1482

Apple TV does not work after trying to update software. Main light keeps blinking and on the screen shows itunes icon and a usb cable. What does that means?

My Apple TV does not work after trying to install the new software update. The main light keeps blinking rapidly and on the screen it shows the itunes icon and a USB cable. What does that mean?

The Apple TV is in recovery mode. Try to restore the Apple TV. Follow the link for instructions on the restore process.
http://support.apple.com/kb/HT4367

ISight camera green light keeps blinking.

using a macbook pro with retina display.
The green light keeps blinking when not in use.
The camera is still able to function.

If you are concerned about the blinking although your camera works, contact Apple Support or an Apple Authorized Service Provider for service.
Message was edited by: EZ Jim
Mac OSX 10.10.1

My Apple TV downloaded as update and since then I can not access the menu. Now the only thing I get is the Apple symbol on my TV screen and the led light on the Apple TV blinks. Apple TV

the only thing I get is the Apple symbol on my TV screen and the led light on the Apple TV blinks.
Apple TV

Welcome to the Apple community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Source list, and then click Restore.

HT1551 my apple tv is only showing apple logo and the white light keeps flashing what do i do

my apple tv is only showing apple logo and the white light keep on flashing can anyone help

You have to restore the device using iTunes
Apple TV (2nd generation): Restoring your Apple TV
support.apple.com/kb/HT4367
You need a micro-usb cable and the ATV must be in DFU mode (Hold down the menu and play button for 7secs)
Apple TV (1st generation): How to perform a factory restore
support.apple.com/kb/HT3199

Laptop won't start quickly but power wifi and caps lock light keeps blinking

Hi, it has happened before too but rarely but nowadays it happens on daily purposes.
When I switch on my laptop after leaving it for 8-9 hrs, it won't start up but instead power, wifi and caps lock light keep blinking. I tried removing battery and pressing power button for few minutes but nothing happens. Then i left it like that with lights blinking and after 15 20 minutes it booted. I did same yesterday too. I left it like that it booted after 20 minutes..so My question is "why is this happening? Is it a motherboard issue or is it because of cold moisturous weather here and laptop takes time to get warm up?" Should I show it to HP Service center?

Hi @Nishant5788
Welcome to the HP Support Forums. I see that you are having a problem getting your notebook to boot up normally. As for what is causing the problem the blinking Caps Lock should tell us what is causing the problem as it should be blinking in a pattern. This HP document Computer Does Not Start and LEDs blink has a chart that will tell you what the blink codes mean.
This is most likely a hardware issue and you can give us a call regarding repair options. You can reach HP Total Care at 1-800-474-6836 in North America or start here if you live outside of North America.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Since I installed Lion on my macbook the LED light does not pulse when I close the screen - the sleep function does not work.

Since I installed Lion on my macbook the LED light does not pulse when I close the screen - the sleep function does not work neither when chosen after pressing the button nor chosen in the apple menu..

I have had the same problem but on another forum it was suggested that disabling internet sharing would solve this. This fix seems to work on my machine - why it works I do not understand

Phone died and I put it on the charger and the red light keeps flashing.

Phone died and I put it on the charger (wall charger) and the red light keeps flashing. It's been doing that for a little less than an hour, I pulled the batttery twice & get the same light flashing. I also read othe posts and it says to just let it charge for a few hours but i don't think it's gonna work. If you know anything about it let me know please & thank you.

When connected to the charger, is the "no battery" symbol showing?
Leave the device to charge 2-3 hours, and then, still connected to the USB cable, remove the the battery from the device a few seconds and reinsert it. If it boots--leave it to charge to 100% (check Options > Status for the percentage). If it doesn't reboot on the first attempt, leave it several more hours. I've had one charge for two days before it came back to life after an extreme battery depletion. Every 3-4 hours, with the device still connected to the charger, you can remove and replace the battery to see if it reboots.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

SG 200-08 All LED lights flashing green after power failure

Thinking back, about a month ago I updated the firmware (sorry I can't check version at the moment). The switch has been working fine since then. Today I needed to move some power cables and the switch lost power. Now ALL of the LED lights are flashing green and I can't access the switch. I've tried setting a static IP on my laptop to 192.168.1.20, mask 255.255.255.0, and accessing the switch on 192.168.1.254, but there's no response. I've tried holding in the reset button for at least 30 seconds while the switch is powered on, AND while powering it on. None of that has worked. Also when I first power it on, the system LED flashes orange very quickly for a second or so, then all of the LEDS start flashing green.
What am I missing?

Its been a few months, so I don't remember the details, but I think it was a combination of using the reset button and then opening a browser to the default IP address. If you look at the screenshot I posted it has the IP address I used. I downloaded the firmware again and the webpage in the screenshot is where the router is asking me for the location of the firmware I downloaded. After it finished reloading the firmware it worked again.

Blackberry LED light keeps flashing red

Yesterday Vodacom Care gave me a new Q5 device - i had a Q5 for 2 months and the phone just went dead - so they replaced it . Now my Q5 LED light keeps flashing red and it's a NEW PHONE ??? - make it stop please !

Hello,
Welcome to the BlackBerry Support Community Forums.
Thanks for the question.
Follow the steps below to try and bring the BlackBerry Q5 back to life:
Ensure that BlackBerry Link is installed on the PC or Mac OS
Ensure the computer has an internet connection.
Launch the BlackBerry Link Software.
Note: A backup of the BlackBerry device should be tried before a reload.
Turn off the BlackBerry device. Make sure there are no flashing LEDs and that the LCD is not still being lit by the backlight. If there are any flashing LEDs, hold the power button for 15 seconds until the LEDs stop.
Connect the BlackBerry device to the computer.
When prompted with Cannot communicate with device, click Restore and then click yes allow the update to be downloaded and installed on the BlackBerry device.
If the restore button is not seen press the vertical dots in the lower right corner of BlackBerry Link and select disconnected device. Highlight the disconnected device you are working with and attempt steps 4 to 6 again.
If the issue still persists, then I suggest contacting your network service provider for repair options.
Let me know if you have any more questions.
Cheers.
VIA | ViciousFerret
http://supportforums.blackberry.com/t5/BlackBerry-Z10/BB-Z10-Died/m-p/2230087#M10125
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution"

HT1551 the led light keeps blinking after restarting it

Similar Messages

Maybe you are looking for