HT1595 Setting date and time

I cannot get the Apple TV to move past the date and time issue. We have had it over a year and never had this problem. We have restarted both the Apple TV and the wireless router. Internet is working on all other devices. Help!

Hey maradi, have you figured out the issue? I'm having the same EXACT problem!!!

Similar Messages

HT1595 setting date and time on apple tv

Cannot set network date and time using apple tv

Welcome to the Apple Community.
Assuming this is not the first time you have used your Apple TV
You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
Also try restarting the router. (Also try removing it’s power cord for at least 30 seconds)
If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If restoring from the Apple TV doesn't help, try restoring from iTunes using a USB cable.
If this is a new Apple TV, in addition to trying the above, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

HT1595 Setting date and time is going around and around

Hello could someone help me?

Hey maradi, have you figured out the issue? I'm having the same EXACT problem!!!

HT1595 The date and time can't be set? What to do?

The date and time can't be set?

I'm having the same issue today on several of our Apple TVs. I am the Director of Technology in a school district and starting this morning I am getting reports that Apple TVs are not working and upon investigation they all sit at setting date and time. All network setting are properly configured. The firewall is set to allow port 123 both TCP and UDP from all internal clients. It occurs both over WiFi and Ethernet.
Is the Apple Time Server experiencing issues?

HT1595 Stuck on Setting Date and Time

Will not set Date and Time (just keeps trying).

I was able to get my Apple TV working again by downgrading the firmware following the instructions in this message:
https://discussions.apple.com/message/20008613#20008613
In case that message disappears, here's my translation:
1. Connect your Apple TV to your computer via USB. Don't plug in the power cable.
2. Download the older 5.0.2 firmware from Apple here:
5.0.2 (Apple TV 2): AppleTV2,1_5.0.2_9B830_Restore.ipsw
5.0.2 (Apple TV 3): AppleTV3,1_5.0.2_9B830_Restore.ipsw
3. Open iTunes and select the Apple TV. Hold down the option key and press the restore button at the same time.
4. In the dialog that opens select the firmware that you downloaded.
5. The restore process will take a few minutes. Once it's done plug your Apple TV back into your TV. If the date and time message persists just press the menu button to skip it. This got mine working again.

HT1595 My apple tv stuck at setting date and time. Also when connecting yo network doesn't ask for network password

My apple tv stuck at setting date and time. Also when connecting yo network doesn't ask for network password

I just went through this last night. (Aug 15, 2013)
What I did to get back up and running. This is not the first time I have lost the network connection with my Apple TV 3
Products effected: Apple TV 3 and Home Sharing (My Apple TV 1 was not effected)
Power down (unplug) the Apple TV and power down your router ( in my case, it is a FIOS router, flipping the on/off works fine).
Power both items back up.
At this point, I usually can reenter my Apple ID and PW. and reconnect Home Sharing. But for some reason I was unable to reconnect last night but was able to get it reconnected in the morning. I was jut to tired to deal with it last night.
A new issue that is was able to fix after a good nights sleep.
I did figure out, (after trying to reenter my ID and PW many times and having it tell me that my ID and PW was wrong), that when using the Apple TV on screen keypad to type in the user ID. DO NOT use the ".com" keypad button. Instead type out each character for .com. ( or what ever ending you use for your ID account.)
Once I typed out my full ID and PW. everything is back to 100%

HT1595 My AppleTV seems to be stuck on the "Setting Date and Time" load page

I just moved from a house to an apartment and when I hooked up my appleTV it said "Setting date and time" with a spinning load wheel and it's been doing this for a long time now. I hit MENU on the remote and tried going to Settings> General> Network like it said at the bottom of the screen, but nothing happened. It's connected to the right WiFi network, but the only icons it shows on the home screen are the 'Computers' icon (for Home Sharing) and the 'Settings' icon. My movies, music, tv shows, netflix etc. icons aren't showing up. I restarted it and got as far as the "Setting date and time" load page again, where it just sits and loads.

Welcome to the Apple Community.
Assuming this is not the first time you have used your Apple TV
    1.    You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
    2.    Also try restarting the router.
    3.    If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If this is a new Apple TV, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

HT1595 how do i access apple tv when screen is stuck at setting date and time

how do i access apple tv when screen is stuck at setting date and time, have unplugged system,restarted router....

Welcome to the Apple community.
Assuming this is not the first time you have used your Apple TV
You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
Also try restarting the router.
If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If this is a new Apple TV, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123.

Lost config and cant set date and time

lost config and cant set date and time apple tv less than month old

Hello there, Terriiris.
I had a similar issue and what worked for me was power cycling my wireless network and the Apple TV. However, if the issue persists, here are a couple articles that will walk you through troubleshooting this issue.
Apple TV: Basic troubleshooting
http://support.apple.com/kb/ht1551
Apple TV: Troubleshooting wireless connections
http://support.apple.com/kb/HT1595
If the steps in the article above do not resolve the issue, then a restore may be needed.
Apple TV (2nd and 3rd generation): Restoring your Apple TV
http://support.apple.com/kb/ht4367
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D.

How do I set date and time on apple tv?

How do I set date and time on apple tv?

Fixed the same problem, STEPS
1. Reset your apple TV
2.It will again stuck on that setting, ignore it by press menu
3. Unplug ethernet wire
4. Try to connect with wifi, it should be work with wifi connection as mine.
5. Then you can switch back Ethernet wire after get fixed.
Thanks. Lemme know dude if it's work.

Setting date and time in java mail

I want to set date and time for the mail sent by my application.
So how to set date and time for my mail.

msg.setSentDate(new Date());Where msg is an instance of javax.mail.Message.

"RT Set date and time" does not set seconds in UTC mode

Hallo,
I tried to set the time on my cRio 9012 with the function settimeUTC which is used by the "Set Date and Time" vi. But the seconds I enter are ADDED to the current time and not set as new value.
Even the vi shows this behaviour: I set up a vi in which the time is set in a loop (100ms delay) and read again. When I set local time the clock stops (as expected) but when I set the UTC time the seconds keep on running...
Can anybody help me with that problem???
Thanks
Florian
Solved!
Go to Solution.

Hi Andreas,
well it does not matter if I set a time zone in the MAX or not. In my example I was working on UTC + 0 but even when I set it to my local time (UTC + 1) I get the same behaviour modified by one hour.
My LabView Version is 8.5. In in the MAX under Software-> LabView-RealTime it says that I am using 8.5.0.
I suspect that the settime.out which is installed on the cRio is probably the root of the problem as VxWorks itself does not offer a function (at least I did not find one) to convert from broken down system time to system time in seconds. There only exist one to convert from broken down local time to system time in seconds ( mktime() ). The reverse function is available for both cases: gmtime() and localtime(). I also did not find a way to find out the offset of the local time. So I have to use the library function settimeUTC() from settime.out.
As I offered I can send you the settime.out file from my cRio for reference or maybe you can tell me how to find out what the version of the file is. It seems not to be an ELF file as I looked inside it to find some timestamp or version info...
Thanks so far
Florian

Is there a way to force time can only be set to "Set date and time automatically"?

I am using OS X 10.9 .5 , and here is what I want to do.
When you click "Open Date & Time Preference", you will find an option that states "Set date and time automatically". And of course you can chose not to do that, and adjust the time.
But can you remove that option? So your OS X is forced to chose the mode "Set date and time automatically" no matter what you do? (aka you can't adjust the time by yourself now.)
Is that possible? Is there an app that can achieve this goal or can you do that at Terminal?
Thanks in advance.

There's a similar setting in iPhoto preferences (in iLife '08 versions and later), or in Image Capture preferences (if you're using iLife '06 or earlier). Check those settings as well.

How do I change the "Set Date and Time Automatically" server

Is there a way to change System Preferences/Date & Time/Date & Time/Set date and time automatically from "Apple Americas/U.S. (time.apple.com)" to another time server instead?

sig wrote:
The menu has a drop down. But if you know the address of another time server I would think you can type it in.
Yeah, that's not really a menu, but a "combo box", which is a combination of an edit field and pop-up menu. So you can choose from existing items or just type in whatever time server you want.
charlie

TS4268 I changed set date and time automatically to "no" and I was able to activate iMessage. This seems contrary to all the troubleshooting discussions I've been reading.

Is there any definitive info on this subject?

When ATV is setting date and time, and hangs there, it usually indicate there isn't a network connection. Is your router still working, is the Internet for all the other computers on the same network working? Have you tried changing from WiFi connection to Ethernet or vice versa?

HT1595 Setting date and time

Similar Messages

Maybe you are looking for