HT1695 I NEED SOME HELP CONNECTING TO MY NEW IPAD

yes i need some help to set my new ipad can u plz help

http://help.apple.com/ipad/5/interface/
Stedman

Similar Messages

I need some help in choosing a new router

I need some advice. I need to get a new router that will last. I have had a Belkin Surf and the reason I got rid of it I thought I need a stronger signal as I was getting a new computer and adding 2 internet radios. SO I bought the D-Link DIR 655. WELL, that lasted 2 months. It is now in to be replaced. Have not got it yet. But because of their rotten attitude and horrible so called customer service. I am looking for another router. Below is a list of what I have and what needs to be connected. The room that the router has to service is 27Ft. X 32Ft.
Main computer is a Dell 8300 4 months old with Windows 7 installed
Second computer is a custom computer with Windows XP Pro. This is 5 years old but works great.
2 internet radios, a Logitech Squeezebox and a Squeezebox Boom
Netflex receiver that streams movies to my television
I have a copier, printer and fax machine attached to the Dell computer
Solved!
Go to Solution.

Looking at the distance of wireless devices a basic router can work very well in your network, But you also have Audio/Video Streaming Devices in the Network So would Like to Recommend E3000 with Key Features
Key Features
Enjoy the power of high-performance Wireless-N technology—optimized for wireless entertainment
Connect your computers, gaming consoles, Internet-enabled HDTVs and Blu-Ray players, and other wireless devices at up to 300 Mbps of transfer speeds
Enjoy the benefits of simultaneous dual-band (2.4 GHz and 5 GHz), including smoother HD video streaming, wireless gaming and file transfers
Share your files at home or on the Internet by connecting a storage device to the Linksys E3000's built-in USB port
Stream video and media content via a built-in UPnP AV media server to an Xbox 360, PS3 or other compatible device
Use four Gigabit Ethernet (10/100/1000 Mbps) ports for faster file sharing with other Gigabit-enabled devices, including computers, hard drives, and servers
Set up your wireless network in a few simple steps using included Cisco Connect software
Keep wireless freeloaders and Internet threats at bay with customizable security settings, including WPA/WPA2 Personal and SPI firewall protection
Give visitors password-protected Internet access on a separate network—so your visitors have access to the Internet, but not your computers or data
Use Cisco Connect's Parental Controls to block specific websites and restrict Internet access during certain hours
Customize your network using easily accessible Advanced Settings

I need some help connecting to LDAP please.

I've been working on this problem for a few days now and I'm really frustrated. I'm going to search through these message boards and hope some topics are of any use. If anyone knows of any please post the links in this thread that would be very helpful.
Here is my problem. My domain name is called swinsk.com. I used a LDAP tool to find my base DN. It came up with DC=swinsk,DC=com.
I am trying to use anonymous bind. When I hit save changes it keeps telling me that my basedn is incorrect and I should that I should check my basedn. When I try to save my changes without an anonymous bind it tells me that my bind DN is incorrect to check that. I am not sure what my bind dn should be if I want to use my administrator account. I'm going to try and figure that out as well. I'm very confused.
If anyone could lend me a hand and point me in the right direction I would be estatic.
The tool I used to find my base DN can be found at: http://www.iit.edu/~gawojar/ldap
I am happy to provide any further information I might have left out to help solve this problem. Thanks in advance to anyone who might give any suggestions!

When I click "Find" under "Manage Organizational Units" it appears to be working. This is what happens:
Search Results
Found 2 entries where the unit name is '*'
Error: Can't connect to the LDAP server
Unit Name Description
Administrators
Domain Controllers Default container for domain controllers
However, when I try to click find under any of the other tabs it says there is a problem and it cannot connect to the LDAP server. This proxy server seems to be very buggy in regards to LDAP. Either that or I am just stupid. I am pretty sure it is set up correctly because I am able to browse LDAP with the LDAP browser tool using the base dn and bind dn I am using in my Global Settings configuration.
Any suggestions?

I need some help on installing the new flash

I have ADD and can get off topic but i will try my best. I have a couple of questions. I am running windows xp home 32 bit. I have IE8, opera and firefox. Is flash version 11.1.102.62 the newest flash? If so then two questions. One when i test my flash with IE it tells me tthe newest version and i'm able to go to the adobe site to upgrade to the right version. However on firefox it does the same thing but then takes me to version 10.3.183.16? I don't know why but i think it happened the last upgradeand i upgraded with opera. So I can update with opera but it doesn't give my the full version numberof the upgrade. Question is are the links you offer, are they for version 11.1.102.62? and if so where do they end up being downloaded to? I'm a pain in the butt but I always have problems when I'm upgrading flash and I decided to ask questions.

Hello John,
Welcome to Adobe Flash Player Forums,
Download and Run Adobe Flash Player uninstaller from here :
http://download.macromedia.com/pub/flashplayer/current/uninstall_flash_player_32bit.exe
Direct link for Flash Player 11 (Internet Explorer)
http://fpdownload.macromedia.com/pub/flashplayer/current/licensing/win/install_flash_playe r_11_active_x_32bit.exe
Direct link for Flash Player 11 (Other Browser)
http://fpdownload.macromedia.com/pub/flashplayer/current/licensing/win/install_flash_playe r_11_plugin_32bit.exe
Download both the setups and run them one by one
Note : Make sure no browsers are running when you are running these .exe files
Hope this helps.
Thanks,
Vikram

Remote App on iPad connects but drops after about 20 mins. Need to turn off wait about 1 minute then turn on wifi on iMac before it can reconnect. Need some help please.

Remote App on iPad connects but drops after about 20 mins. Need to turn off wait about 1 minute, then turn on wifi on iMac before it can reconnect. Need some help please.
Already gone through troubleshooting guide a zillion times. Thanks.

This worked for me... A little time consuming but once you get rolling it goes GREAT... Thanks....
I got my artwork and saved it to my Desktop
Opened up Microsoft Paint and clicked on "File" and "Open" and found it to get it on the screen to resize it
Clicked "resize" and a box for changing it opened up
Checked the box "Pixels" and "Unchecked maintain aspect ratio"
Set Horizontal for 640 and Vertical for 480
Clicked on "OK" and went back to "File" and did a "Save As" and chose JPEG Picture
It came up "File Already Existed" and clicked "OK" (really did not care about the original artwork I found because wrong size)
Went to iTunes and on the movie right clicked on "Get Info", clicked on "Details", then "Artwork"
Go to the little box on the top left that shows your old artwork and click on it to get the little blue border to appear around it and hit "Delete" to make it gone
Click on "Add Artwork" and find it where you put the one from above on your Desktop and hit "Open" and OK and your new artwork is now there and all good.
Sounds like a lot of steps to follow but after around 5 or so you will fly through it. This worked perfect on my iPhone 6 Plus and I have artwork on my Home Videos now.

TS2634 Please People I need some help.My iPod is disabled and when I connect it to iTunes it says: Itunes could not connect to the ipod because it is locked with a passcode...

Please People I need some help.My iPod is disabled and when I connect it to iTunes it says: Itunes could not connect to the ipod because it is locked with a passcode...how can I do it?

Place the iPod in Recovery mode and then restore.

Ok I got my iPod from my brothers friend and my IPod says "iPod is disabled connect to iTunes" then my computer says cannot get onto iPod because I need the iPod passcode and of course I cannot put it in so I need some help please

Ok i got my iPod from my brothers friend and my IPod says "iPod is disabled connect to iTunes" then my computer says cannot get onto iPod because I need the iPod passcode and of course I cannot put it in so I need some help please

Try placing in DFU mode and then restoreing.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

My iphone has error9 code, it keeps showing connect to itunes,need some help

i need some help please,, i already updated my latest itunes version, usb troubleshooting done, need some help please

http://support.apple.com/kb/TS3694#error9
USB:
Use a port directly on the computer, not a hub. If it is not a laptop and has ports on the back and front use a port on the back.
Security Software:
Disable your antivirus and firewall, then restore.
Other:
If the phone has been jailbroken that is likely the cause of your problem. Also, if the computer you are using to restore has been used to jailbreak any iOS device in the past.

I'm looking for some help connecting linksys IP Cameras to my home network to monitor my property when I'm travelling. I used to do this with linksys WAPS, but since I've discarded all my old linksys networking and standardized on airport, I can't get the

I'm looking for some help connecting linksys IP Cameras to my home network to monitor my property when I'm travelling. I used to do this with linksys WAPS, but since I've discarded all my old linksys networking and standardized on airport, I can't get these things working. I know that I have to identify my camera through the DHCP table and set up port forwarding and there is the problem.
My network consists of 4 base stations set up in a roaming network - same network name and passwords. I need to do it this way so I don't have to switch network when I move from one side of the house to the other, go to the cabana, or my shop in the barn. The network works pretty well since I went to a roaming set up. Good performance, yata, yata, yata.
However, the roaming network requires the AEBS's to be set up in bridge mode, rather than sharing an ip address. When the AEBS is set to bridge mode, you don't see a DCHP table or have the ability to identify your IP Cam through the AEBS - and hence, no port forwarding.
I am able to identify and set up my Linksys IP Cam by locating the ip address on my FIOS router, even though, it's plugged into an AEBS. I set it up, see the video, remove the ethernet cable from the IP Cam, restart - and I can't get to it from an AEBS. In researching this, it appears, I should be setting up the AEBS to "share an IP Address", going to the DHCP table and identifying the camera's IP address and setting up port forwarding. However, you don't see any of the DHCP or port forwarding options in Airport Network Utility when configuring in bridge mode.
I'm hoping I'm missing something here and that the solution isn't to set it up at the FIOS router level, but I'm beginning to think that's my only hope. What concerns me there is that I should be able to see the IP cam on the network without port forwarding since I'm not coming from outside, and I can't even do this unless it's connected hard wire.
I'd appreciate any insight into this that anyone might have. I've hit the wall with what I know.
Thanks.

In a roaming network, your "main" router is the device that would require port mapping/forwarding to be configured in order to access the IP camera from the Internet. This router is also the one that would be provide the private IP address for the camera which you will want to be a static one.
So as you described your network, the IP cameras should be getting an IP address or you assigned it a static one and this is the address that you would enter in the Private IP address (or equivalent depending on the router used) field when setting up port mapping.
If you are not able to access this camera from the local network, then this should be troubleshot first.

Need some help in creating Search Help for standard screen/field

I need some help in adding a search-help to a standard screen-field.
Transaction Code - PP01,
Plan Version - Current Plan (PLVAR = '01'),
Object Type - Position ( OTYPE = 'S'),
Click on Infotype Name - Object ( Infotype 1000) and Create.
I need to add search help to fields Object Abbr (P1000-SHORT) / Object Name (P1000-STEXT).
I want to create one custom table with fields, Position Abb, Position Name, Job. Position Abb should be Primary Key. And when object type is Position (S), I should be able to press F4 for Object Abb/Object Name fields and should return Position Abbr and Position Name.
I specify again, I have to add a new search help to standard screen/field and not to enhance it.
This is HR specific transaction. If someone has done similar thing with some other transation, please let me know.
There is no existing search help for these fields. If sm1 ever tried or has an idea how to add new search help to a standard screen/field.
It's urgent.
Thanks in advace. Suitable answers will be rewarded

Hi Pradeep,
Please have a look into the below site which might be useful
Enhancing a Standard Search Help
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/daeda0d7-0701-0010-8caa-
edc983384237
http://help.sap.com/saphelp_nw04/helpdata/en/cf/21ee93446011d189700000e8322d00/frameset.htm
A search help exit is a function module for making the input help process described by the search help more flexible than possible with the standard version.
This function module must have the same interface as function module F4IF_SHLP_EXIT_EXAMPLE. The search help exit may also have further optional parameters (in particular any EXPORTING parameters).
A search help exit is called at certain timepoints in the input help process.
Note: The source text and long documentation of the above-specified function module (including the long documentation about the parameters) contain information about using search help exits.
Function modules are provided in the function library for operations that are frequently executed in search help exits. The names of these function modules begin with the prefix F4UT_. These function modules can either be used directly as search help exits or used within other search help exits. You can find precise instructions for use in the long documentation for the corresponding function module.
During the input help process, a number of timepoints are defined that each define the beginning of an important operation of the input help process.
If the input help process is defined with a search help having a search help exit, this search help exit is called at each of these timepoints. If required, the search help exit can also influence the process and even determine that the process should be continued at a different timepoint.
timepoints
The following timepoints are defined:
1. SELONE
Call before selecting an elementary search help. The possible elementary search helps are already in SHLP_TAB. This timepoint can be used in a search help exit of a collective search help to restrict the selection possibilities for the elementary search helps.
Entries that are deleted from SHLP_TAB in this step are not offered in the elementary search help selection. If there is only one entry remaining in SHLP_TAB, the dialog box for selecting elementary search helps is skipped. You may not change the next timepoint.
The timepoint is not accessed again if another elementary search help is to be selected during the dialog.
2. PRESEL1
After selecting an elementary search help. Table INTERFACE has not yet been copied to table SELOPT at this timepoint in the definition of the search help (type SHLP_DESCR_T). This means that you can still influence the attachment of the search help to the screen here. (Table INTERFACE contains the information about how the search help parameters are related to the screen fields).
3. PRESEL
Before sending the dialog box for restricting values. This timepoint is suitable for predefining the value restriction or for completely suppressing or copying the dialog.
4. SELECT
Before selecting the values. If you do not want the default selection, you should copy this timepoint with a search help exit. DISP should be set as the next timepoint.
5. DISP
Before displaying the hit list. This timepoint is suitable for restricting the values to be displayed, e.g. depending on authorizations.
6. RETURN (usually as return value for the next timepoint)
The RETURN timepoint should be returned as the next step if a single hit was selected in a search help exit.
It can make sense to change the F4 flow at this timepoint if control of the process sequence of the Transaction should depend on the selected value (typical example: setting SET/GET parameters). However, you should note that the process will then depend on whether a value was entered manually or with an input help.
7. RETTOP
You only go to this timepoint if the input help is controlled by a collective search help. It directly follows the timepoint RETURN. The search help exit of the collective search help, however, is called at timepoint RETTOP.
8. EXIT (only for return as next timepoint)
The EXIT timepoint should be returned as the next step if the user had the opportunity to terminate the dialog within the search help exit.
9. CREATE
The CREATE timepoint is only accessed if the user selects the function "Create new values". This function is only available if field CUSTTAB of the control string CALLCONTROL was given a value not equal to SPACE earlier on.
The name of the (customizing) table to be maintained is normally entered there. The next step returned after CREATE should be SELECT so that the newly entered value can be selected and then displayed.
10. APP1, APP2, APP3
If further pushbuttons are introduced in the hit list with function module F4UT_LIST_EXIT, these timepoints are introduced. They are accessed when the user presses the corresponding pushbutton.
Note: If the F4 help is controlled by a collective search help, the search help exit of the collective search help is called at timepoints SELONE and RETTOP. (RETTOP only if the user selects a value.) At all other timepoints the search help exit of the selected elementary search help is called.
If the F4 help is controlled by an elementary search help, timepoint RETTOP is not executed. The search help exit of the elementary search help is called at timepoint SELONE (at the
F4IF_SHLP_EXIT_EXAMPLE
This module has been created as an example for the interface and design of Search help exits in Search help.
All the interface parameters defined here are mandatory for a function module to be used as a search help exit, because the calling program does not know which parameters are actually used internally.
A search help exit is called repeatedly in connection with several
events during the F4 process. The relevant step of the process is passed on in the CALLCONTROL step. If the module is intended to perform only a few modifications before the step, CALLCONTROL-STEP should remain unchanged.
However, if the step is performed completely by the module, the following step must be returned in CALLCONTROL-STEP.
The module must react with an immediate EXIT to all steps that it does not know or does not want to handle.
Hope this info will help you.
***Reward points if found useful
Regards,
Naresh

My airport problem has returned big time --Need some Help!!

Aloha once again:
I though that this was fixed by simply changing channels on my airport router, but that fix only lasted for a few days, but now it's back and even worse. Let me give you some background on this problem. Here's my original message concerning the problem:
I have my Airport Router connected to the Internet via DSLcable. I then tie my two computers into the internet via their airport cards. For about 6 months this system has been working just fine. Recently my desktop computer quit listening to the router and can no longer connect to the internet. It shows no signal strength and the name of the network on the Airport is not seen in the "connect to internet" panel. The same Airport works just fine on my LapTop and I am using it right now to get this message off to the internet.
I have fixed permissions, removed the airport card and cleaned the connector, the antenna plug and removed the system configuration folder from library preferences all to no avail!
This problem has been hounding me, intermittently, for over a year now What can I do to remedy this??? HELP!!!!
Dan Page
Maui, Hawaii
The suggestion to change channels, that came from this original request, worked but just for a very short time. Now I have to shut down my computer overnight to get connected and then it only lasts for several hours and the connection quits.
I thought maybe heat was a problem, but the last time it happened I opened the computer and played a large fan right on the card. This did not help. I shut it down for the night and it was fine the next morning for about 2 hours.
One new data point; if I turn off just the airport on my laptop computer overnight, that will fix the problem for a short time also.
Still need some help!!!
Dan

First, power off both the Time Capsule and AirPort Express.
Wait a few minutes, then power up the Time Capsule first, and let it run for a few minutes.
Temporarily, move the AirPort Express to the same room or close proximity to the AirPort Express and power it up.
If the Express powers up correctly, power it off again and move it approximately half the distance between the Time Capsule and the general area that needs more wireless coverage. Try to minimize obstructions like walls, ceiling, heavy furniture, etc as much as possible.
Please report on your results.

Hi, can anyone help me out with this, I need some help on designing GUI for e-learning coursewares. Some tutorials or some helpful sites will do.

I need some help with the GUI design.

Have you tried the line inputs on the back of your FirePod? If you update its firmware (not sure if you will need to or not), I seem to remember hearing that the FirePod can run without FW connection, i.e. stand alone. In this mode with the outs from your mixer into line ins 1-2 (2nd from left on the back) it should work fine. I say should because I have never tried. However, these are used for returns from an external effects unit. I assume here, and the important word is assume, that there are two so that they can be used as a stereo send or as a mono send. Worth a try! Let us know how it goes.
Best, Fred

Need some help with a Macally enclosure and a spare internal drive

Need some help with a Macally enclousure
Posted: Oct 1, 2010 10:55 AM
Reply Email
Aloha:
I have a Macally PHR-S100SUA enclousure that does not recognise,my WD 1001fals hard drive. It has worked just fine with other internal drives, but not this one?
This is a spare internal drive that I am trying to make an external drive to store back ups for a lot of data. But so far I can not get it recognized by the computer. Maybe I need different drivers?
Any suggestions?
Dan Page

Hi-
Drivers aren't typically needed for external enclosures.
Macally has none listed for that enclosure.
The same is true for the WD drive, internal or external; no drivers.
With the exception of high end PM multi drive enclosures, I can't think of any that use drivers.
How is the external connected?
Have you tried different cables, different ports?
Bad/damaged cables are fairly common.
Have you verified connections inside of the enclosure?

We have a set of oracle clients running on T5220 zones that need some help

Greetings all -
We have a set of oracle clients running on T5220 zones that need some help.
If, for example, I execute the query "select (all) from dba_objects", trace output reports 90% of the elapsed time spent under "SQLNet message from client".
Here are OS details for the clients: Solaris 10 5/08 s10s_u5wos_10 SPARC
Running "uname -a" from the client gives:
(SunOS bmc-ste-app 5.10 Generic_127127-11 sun4v sparc SUNW,SPARC-Enterprise-T5220)
Here are OS details for the dataserver: Enterprise Linux Enterprise Linux Server release 5.2
Running "uname -a" from the dataserver gives:
(2.6.18-92.1.6.0.2.el5 #1 SMP Thu Jun 26 17:44:55 EDT 2008 x86_64 x86_64 x86_64 GNU/Linux)
The RDBMS is 10.2.0.4
Again, please note, there is no application in the picture here. We are just running a simple catalog query (select * from dba_objects) from sqlplus. Why the wait on something like this? The wait also occurs when a different query is used (select (all) from SYS.COL$ where rownum < 50000). And it doesn't matter if I used the full client or the instant client. I still get the same high-wait.
We had thought - maybe this is a network thing - so we put a test client on the same subnet as the dataserver. This helped - but not enough. The wait is still way too high even with firewalls taken out of the equation.
We've also looked at arraysize, SDU, kernel settings. And we've spent time going over tkprof, truss and sqlnet-tracing.
Has anyone ever had to solve this HIGH WAIT ON CLIENT issue? Is there a work around or some tweak I'm missing.
Is anyone configured like we are (linux dataserver, solaris clients)? If so - did you see anything like this?
tia -
Jim
Edited by: jim1768 on Mar 31, 2010 1:47 PM
Edited by: jim1768 on Mar 31, 2010 2:12 PM
Edited by: jim1768 on Mar 31, 2010 2:13 PM

Hello,
We have the exact same issue. Did you ever solve this issue? We have a t5220 and have just upgraded our 11.5.10.2 11i system on it from 9.2.0.8 32-bit sparc to 11.2.0.1 64-bit sparc. Things should be faster but arent, and our consultant has tracked it down to high wait times when the apps tier using forms connects to the database tier on the same box. So even though the t5220 is both server and client, there is something about the client sql connection.through TNS that his having trouble. Thanks for any information. We've also created an S/R with Oracle.
Note: I am well aware of the other issues with the CMT server series but this particular issue seems independent of the regular / known issues and remains a mystery to us. Other known issues with the CMT servers for SPARC:
Metalink Note 781763.1 (Migration from fast single threaded CPU machine to CMT UltraSPARC T1 & T2)
http://blogs.sun.com/glennf/resource/Optimizing_Oracle_CMT_v1.pdf
http://blogs.sun.com/glennf/tags/throughput
http://blogs.sun.com/glennf/entry/getting_past_go_with_sparc
http://www.oracle.com/apps_benchmark/doc/E-Bus-11i-PAY_ORA_SUN-T5220.pdf (this paper has some oracle init settings at the end. The kernel settings have been included in the OS upgrade)
http://blogs.sun.com/mandalika/entry/siebel_on_sun_cmt_hardware

Need some help! My iPhone 4 cannot play music through it's built in speaker, only with headphones. I also cannot adjust volume, it only shows "ringer". I really do not know when it starts. I already clean the jack and dock,reset it. Update it to IOS 7.1.1

Need some help! My iPhone 4 cannot play music through it's built in speaker, only with headphones. I also cannot adjust volume, it only shows "ringer". I really do not know when it starts. I already clean the jack and dock,reset it and still cannot be fixed. I updated it to IOS 7.1.1 recently only, does it have connection with the inconvenience I am experiencing right now? What should I do? Thanks!

Hi Melomane1024,
If you are still having issues with your iPhone’s speaker, you may want to look at the steps in this article -
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/TS5180
Thanks for using Apple Support Communities.
Best,
Brett L

HT1695 I NEED SOME HELP CONNECTING TO MY NEW IPAD

Similar Messages

Maybe you are looking for