HT1731 Airport wont show up in Airport Utility when in client mode.

When i follow these steps on my Airport Extreme it restarts but then it wont show up in Airport Utility and my PC or Xbox wont connect to the internet through ethernet. The amber light is green and the AE is connected to my iPhone. I'm sharing internet from my iPhone and using the Airport Utility on my PC. Any advice?

I am not sure that I understand your setup, but it might be important to note that the AirPort Extreme needs an Ethernet connection at its WAN "O" port to be able to provide an Internet connection to any devices that are connected to the LAN Ethernet ports on the Extreme.
If you happen to have the AirPort Extreme picking up a wireless signal, the Ethernet ports are not enabled on the Extreme in this type of setup.

Similar Messages

  • Airport wont connect on my home network when its password protected but..

    Airport wont connect to my home network when its password protected. It will connect to my network if i go into my linksys router and set the network to "not password protected". If i put on the security and choose a pass phrase it always says connection failed when i try to connect to the network. anyone got any suggestions on what to try ?
    ps and yes i am putting in the password right

    Hi Nickerjones
    When you enter your password for the Linksys router, is it generating a separate code phrase? By this, I mean if you enter "password", the Linksys converts this to a code that might look something like "ju457re76en7pq" for example. The code is generated based on an algorithm that Linksys uses for their products and should be visible in the set up page. Sorry, I haven't used Linksys for several years so I can't remember all the details.
    Other manufacturers use different algorithms for their products, so if you entered "password" on an Apple product, it would likely convert the phrase to a different code, which the Linksys would not recognize. If you can locate the actual code that the Linksys generates when you enter your password and use that same exact code when you enter the password for your wireless on Airport, you may have your problem solved.

  • HT1539 the movie uploaded to my itunes but it wont show in my movie folder when i want to add it to my iphone. how do i get it into my iphone

    how do i transfer my movie to my iphone. its showing up on itunes but it wont show up when i want to put it on my phone

    I FIGURED IT OUT. THANK FREAKING GOD!
    This is what I did:
    I went to control panel and unistalled iTunes completely, then I installed 10.6.3
    http://support.apple.com/downloads/#itunes which you can find here
    It came up with an error saying that my library had beed used with a more updated verision, basically had to upgrade. I installed iTunes 10.7
    After it had installed and iTunes was running I hooked up both my iPhone and my flash drive, I have more than 1 usb port I figure most computers do now, and by the time and date in the bottom right corner a small icon came up showing that I had devices hooked up. It showed both my iPhone (but did not know what it was) and my flash drive. If you right click on the iPhone it has the option to Troubleshoot it. I did it and my iPhone 5 now FINALLY SYNCS!
    I'm sooo happy now.

  • AirPort Express shows lowercase in AirPort Utility

    I use an AirPort Express 802.11n (v7.5.2) to extend my wireless network with a Time Capsule 802.11n (2nd Generation / v7.5.2) as a base router. When I enter the 'Logging & Statistics' of my Time Capsule via the AirPort Utility (via: Manual Setup > Advanced > Logs and Statistics > DHCP clients), I found out that only the name (Client ID) of my AirPort Express is changed in only lowercase characters (from Luna into luna), while all the other devices (like my iPad, iPhones, iPods, printers, Apple-TV, etc.) contain their original set of upper- and lowercase characters.
    Can someone please explain to me why only the name (Client ID) of the AirPort Express is changed into lowercase?

    My airport express is also changed to all lowercase in the DHCP clients list.  ONLY the airport express has this change.  Also for some reason my Airport Express will not use the IP reservation based off of the DHCP client ID.  No idea why this is happening.

  • Gray Screen, HD not showing up on Disk Utility while in Recovery Mode

    After in Recovery Mode and opening Disk Utility, the only thing that shows up in the left panel is, "disk0" and "Mac OS X Base System".
    Macbook A1278
    Latest version of OS X Mavericks

    Yes.  Look at these iFixit instruction links:
    https://www.ifixit.com/Device/MacBook_Pro_13%22
    http://https://www.ifixit.com/Guide/MacBook+Pro+13-Inch+Unibody+Late+2011+Hard+D rive+Replacement/7656
    You will need a #00 Phillips and a #6 Torx drivers.
    Ciao.
    (select the instructions for your exact MBP)

  • NANO wont show up/connect with Itunes when plugged in!!!

    I am trying to change some of my music on my nano and when I go to plug it in... it doesn't show up in Itunes. I recently purchased the iphone and when I plug that into the computer I "CAN" see it... and do updates, etc. Ever since I have been using my iphone with itunes, I am not able to change anything or "see" my nano on the itunes main page. Please help!

    I'm having exactly the same problem. And iTunes keeps jumping into the foreground/ launching when it's docked. I want the data from my last and fastest workout in the Nike+ from it-- butI can't even restore the iPod since iTunes won't read it (despite Finder mounting it).

  • Panel Customizable not showing Oracle BI under Mashups, when in Composer mode

    I had created a page with panel Customizable:
    <?xml version='1.0' encoding='UTF-8'?>
    <jsp:root xmlns:jsp="http://java.sun.com/JSP/Page" version="2.1"
              xmlns:f="http://java.sun.com/jsf/core"
              xmlns:h="http://java.sun.com/jsf/html"
              xmlns:af="http://xmlns.oracle.com/adf/faces/rich"
              xmlns:cust="http://xmlns.oracle.com/adf/faces/customizable"
              xmlns:pe="http://xmlns.oracle.com/adf/pageeditor">
      <jsp:directive.page contentType="text/html;charset=UTF-8"/>
      <f:view>
        <af:document id="d1">
          <af:form id="f1">
            <pe:pageCustomizable id="pageCustomizable1">
              <cust:panelCustomizable id="panelCustomizable1" layout="scroll"/>
              <f:facet name="editor">
                <pe:pageEditorPanel id="pep1"/>
              </f:facet>
            </pe:pageCustomizable>
          </af:form>
        </af:document>
      </f:view>
    </jsp:root>
    Earlier, I had installed all jDeveloper extensions
    Business Intelligence ADF Task Flow
    Business Intelligence ADF View Regions
    Business Intelligence Composer
    Business Intelligence Logical SQL View Objects
    Business Intelligence Soap Connection
    I followed the instructions given here
    I had included library oracle.bi.jbips in weblogic-application.xml
    I had included library oracle.bi.composer in weblogic.xml  (both of these steps are from the same instructions)
    I have included the following libraries for BI in my Webcenter Portal project:
    BI ADF Runtime
    BI ADF Taskflow
    BI JDBC
    BI SOAP Connection Runtime
    BI View Object Runtime
    BI JIBPS
    Then, I right-click on the jspx file shown above (from Application Navigator) and click Run.
    After the page shows up, I press Cntrl + Shift + E.  Content Editor window shows up.
    I select "Add Content".  In the popup that comes up, I select "Mash-Ups".  After that, "Oracle BI" should appear.  But it doesn't
    Can someone please help me figure out why I am not seeing "Oracle BI" option in the popup after I select "Mash-Ups"?

    Hi Vetsrini,
    Many thanks for offering to help. It has just been solved. It was a typo in the XML of the name of the column.
    Doh! Obvious now that I know!
    - Jenny

  • Airport express wont show up in utilities wireless or wired

    some times my airport express wont show up in airport utilities on both mine and my wifes macbooks but my i pads and phones keep connection to internet but the books wont. i run ethernet cable to the macbook and sometime it reads the express and some times it wont not quite sure whats wrong.

    Thank you for your post, but I do not understand why you are giving me a link to the generic airport express site. The configuration I have was working fine before I upgraded my router.

  • AirPort Express in client mode with WEP

    I just bought an AirPort Express that I'd like to use in client mode so I can stream music from my laptop to my stereo. I have an existing wireless G network supported by a Netgear WGR614v4 router, using 64-bit WEP encryption. My laptop is a Dell Studio 15 running Vista Home Premium, and it has a Dell Wireless 1387 card.
    I know there are some reported issues with AE and WEP encryption, but for whatever reason my laptop doesn't connect to WPA networks, so I'm stuck on WEP. I've been using WEP 64-bit, so I attempted to setup the AE to work with that. The AE was connected directly to my Netgear router, and I installed the AirPort Utility software on my Dell laptop. Went through the setup, entered my WEP passkey, and then got to a screen where I clicked "update AE" or something of that sort. It then showed a windows with some upload bars on it that made it look like it was doing something, but it finally resulted in an error message saying the AE could not be found following the update. After looking for help, I stumbled across the following thread:
    http://discussions.apple.com/thread.jspa?threadID=1765010&tstart=0
    which in Step 6 he mentions this "error" is normal. That gave me hope, so I disconnected the AE from the router and moved it to the other room where my stereo is. Plugged in the mini cable, then plugged the AE into the wall and allowed it to run its setup sequence. Eventually I had a solid green light, so I figured I was in good shape.
    Problem is that I then opened the AirPort Utility software on the Dell laptop to complete the setup and activate AirTunes, but the AirPort Utility doesn't show the AE connected. If I log into my router utility though, it does show the AE as one of the devices on my network, so somewhere there is a disconnect. After reading some more, I realized I could manually connect via AirPort Utility by entering the AE IP address and password. Tried this and it seemed to work because it showed the info for my AE, but when I closed that window it was gone. I figured maybe that's just a bug with AirPort Utility, so I closed it out and went to iTunes, hoping to see the option for selecting AE as the audio output, but it's not there.
    I've tried almost everything I can think of, but I'm having no luck. At times I feel like I'm even making negative progress because I'll start everything from scratch and it will get hung up at a step earlier in the process. For instance, right now I've just restarted from scratch and the AirPort Utility can't even connect to the AE to do the initial setup. For some reason, following a Factory Default Reset, and with the AE connected directly to the router, it now boots up to a solid green light, shows up in AirPort Utility under a default base station name, yet the AirPort Utility can't connect to modify my wireless settings.
    Does anyone have any advice?

    1) are both the LAN and WAN ethernet ports available or only one of them, the LAN port presumeably?
    Both ports operate as LAN ports in this type of setup, since the Express will be configured in Bridge Mode automatically.
    2) If you unplug the ethernet cable momentarily to connect a different device, does the AX drop the wireless connection or is it maintained?
    Wireless will be maintained, but you may need to power off and restart the Express. 
    Better practice would be to power off the Express before you disconnect the cable(s), connect the cable(s) again, then power up the AirPort Express.

  • Western Digital drive not showing up in disk utility--Help please.

    Hello all. This is my first post. I am having trouble with my WD 500GB external hard drive. It is not showing up in disk utility when connected either via the firewire or USB ports. I purchased the drive about 8months ago, brought it home and set it up as my Time Machine backup drive. It worked great for several months, until it got full. Then it stopped showing up on the desktop for no apparent reason. I discovered through reading support documents on the Apple web site that when I set the drive up initially I should have changed the partitioning protocol from master boot record to GUID, but I did not. I followed the apple web site instructions for making the change expos facto, but was instructed to press buttons that were "grayed out". As such, I couldn't do it. Perhaps foolishly, I thought that I would just start all over by reinitializing it, formatting it correctly (with my new found knowledge) and then do the time machine backup fresh. However, the drive no longer shows up in disk utility no matter how or in what order I connect it. When the drive is connected by firewire there is evidence of some recognition of the drive in system profiler, but it is listed as "External HDD Buttons and Lights". There is also evidence of the My Book showing up at a minimal level (eg. the firmware revision and a few other details are listed). On the front of the drive is a ring of blue lights that progress in a clockwise direction as soon as a connection is made via either firewire or USB. Before that it is solid blue. I have read through all the info that I can find on this site, and all the suggestions require the drive being recognized in disk utility. Without that, I am stuck. I know this must be a solvable problem, because the drive just a bucket of parts before it was manufactured. I just don't know enough to solve the problem or even know what qeustion to ask. I would really appreciate some help. Thanks in advance, and sorry for the long post.

    If you can't boot from an OSX DVD, it sounds bad. Yet I think you said you were running Disk Utility from the DVD?
    I got an external Firewire drive enclosure for 2.5 inch IDE drives from Other World Computing (OWC)
    http://eshop.macsales.com/item/Other%20World%20Computing/MOTGFW400/ but similar items are available from many vendors like Newegg. About $60 for the basic model. More money can buy additional interfaces on the enclosure like FW800 and USB2; an AC adapter instead of letting the firewire bus power the drive (usually OK).

  • Ipod touch wont show up in usb or itunes help pages just bring me in circles.  how can i get it to show up.  I use windows xp at home and tried everything then tried a relatives computer using windows 7 and still nothing.  this is an older ipod touch

    the help pagers just bring me around in circles.  the ipod doesn't show up in system devices under the busses.  i've tried just about everything.  Im using windows xp at home and though maybe it was because of that. so went to a relatives and used a brand new lap top avus with windows 7 and it wont show up here either.  When i got the ipod a few days ago from a third party the only screen i could get to come up was a picture of a usb cord with an arrow pointing towards the itunes logo.  I downloaded i tunes and couldn't get it to change.  brought it to at&t store today they hooked it up with my usb cord to thier computer and suddenly the menu screens work and i could even get online with it yet when i try to hook it up to one of my computers it doesn't show up anywere where can i go to get this fixed and fixed quick jumping around the apple help pages have put me in a foul mood and im sick of it two days spent trying to get it to show now.  im sick of waiting around i need help asap so i can return this **** thing if it turns out it is broken somehow..which i dont think it is.

    What gen iPod (3,4?) did you buy?

  • IWeb wont show my changes.

    Hi everyone.
    My name is Takin, and im a graphical designer. This is my site: www.icandidesigns.com
    Just recently found out about iWeb and its possibilites, but now ive encountered a problem.
    If you see under 'portfolio' you can see that i only have two albums.
    But in iWeb, i have three! So the third wont show up! Im using Filezilla FTP client - and all the necessary files are allready on my one.com server - but it just wont show!
    What am i doing wrong?

    Welcome to Apple Discussions iCandi,
    When I visit your Portfolio @ http://www.icandidesigns.com/Portfolio/Portfolio.html I see 3 albums:
    POSTERS, PHOTOSHOP CARS, and LOGO DESIGNS.
    If these are the 3 that you are referring to then I think you are ok. That means that you published fine. Your web browser may need to be reset to get rid of your caches. If you are using Safari http://docs.info.apple.com/article.html?path=Safari/3.0/en/9300.html.
    Hope that helps.

  • Airport Express disconnects every 5mins (Client Mode)

    Hi all,
    I recently bought an Airport Express (n) so I could stream music to my Hi-Fi and bridge my Xbox 360.
    I have configured the AX to connect to my existing wireless network which is served up by a Billion 7800n router (G+N mode).
    However, every 5 minutes it disconnects from the network, here are sample of the logs..
    Dec 16 06:29:45 Severity:5 Installed unicast CCMP key for authenticator 00:04:ed:9b:bf:39
    Dec 16 06:34:59 Severity:5 Disconnected from network.
    Dec 16 06:35:05 Severity:5 Joined BSS 00:04:ed:9b:bf:39
    Dec 16 06:35:05 Severity:5 Installed unicast CCMP key for authenticator 00:04:ed:9b:bf:39
    Dec 16 06:40:10 Severity:5 Disconnected from network.
    Dec 16 06:40:16 Severity:5 Joined BSS 00:04:ed:9b:bf:39
    Dec 16 06:40:16 Severity:5 Installed unicast CCMP key for authenticator 00:04:ed:9b:bf:39
    Dec 16 06:45:21 Severity:5 Disconnected from network.
    Dec 16 06:45:27 Severity:5 Joined BSS 00:04:ed:9b:bf:39
    Dec 16 06:45:27 Severity:5 Installed unicast CCMP key for authenticator 00:04:ed:9b:bf:39
    Dec 16 06:50:33 Severity:5 Disconnected from network.
    Dec 16 06:50:38 Severity:5 Joined BSS 00:04:ed:9b:bf:39
    Dec 16 06:50:39 Severity:5 Installed unicast CCMP key for authenticator 00:04:ed:9b:bf:39
    Dec 16 06:55:44 Severity:5 Disconnected from network.
    Dec 16 06:55:49 Severity:5 Joined BSS 00:04:ed:9b:bf:39
    I'm using WPA2 AES encryption, wireless is on a non-competing channel and the airport is only 2-3 meters away from the router in the same room.
    Things I've tried are upgrading Router firmware to latest (1.6), switching Wi-Fi channels, enabling B mode on the router (BGN) but nothing seems to work.
    I don't think it's interference as it disconnects almost every 5 minutes which suggests some config/hardware issue.
    Anyone have any ideas? I've hit a brick wall.
    Thanks...

    Update:
    This appears to be by design? - connection doesn't drop when using AirTunes/Airfoil which is what I bought it for.
    However I thought the Ethernet port wouldn't work when used in Client mode (according to the FAQ). I was able to connect my Xbox 360 to the AX when in Client mode using a network cable and it is able to connect to Xbox Live. When doing this it drops off on the 5 minute intervals when the AX disconnects and reconnects.
    I guess if I used AirTunes at the same time as the X360 it would work.
    Would be nice if it worked as a stable bridge in client mode as I could bin off my other wireless bridges. Never mind - I ain't forking out for another AX so I can use "Apple's" WDS.
    Message was edited by: MonkeeBoy_UK

  • Printer wont show up when plugged into timecapsule, and backups in pink wont restore?

    i recently purchased a TC and my printer wont show up on the network when plugged into the usb port? i also cannot restore anything from backups in pink? any solutions

    When you open Print & Fax to add the HP device, are you then clicking on it to highlight it, then clicking Add at the lower right to install the device?
    When you do this, you will have the HP device installed in two "locations"....one at the Mac and the other at the TC. When you try to print, you have to be sure to choose the correct location.
    The PCs will need to have Bonjour for Windows installed on each device. Run the program, and select the HP device.   Bonjour Print Services for Windows v2.0.2
    Keep in mind that only the print function will work on most All-in-One type devices when connected to the USB port on a router. You need to connect to a computer if you need advanced features like copy, scan, maintentenance, etc.

  • Downloaded Firefox it does not show but is open for when I uninstall it I am requested to close ff which cannot be done as it does not show

    After a check on compatibility of Add Ons by FF after opening it, it stopped working. I re installed FF and the same happened. I have FF re installed but now it wont show the start page and when trying to remove FF I am requested to first close FF. to do this I have to close my PC ( Windows XP) as the FF opening page does not show and I consequently can not close it
    I like using FF, all my bookmarked info and references for a book I am writing is on it so I have to get it working

    It is possible that your security software (firewall, anti-virus) blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox and the plugin-container from the permissions list in the firewall and let your firewall ask again for permission to get full, unrestricted, access to internet for Firefox and the plugin-container process and the updater process.
    See:
    *https://support.mozilla.org/kb/Server+not+found
    *https://support.mozilla.org/kb/Firewalls
    *https://support.mozilla.org/kb/fix-problems-connecting-websites-after-updating

Maybe you are looking for