HT1998 what is the latest update for Airport Express 802.11n with the Mac OSX10.6.8

what is the latest update for Airport Express 802.11n with Mac OSX 10.6.8?

You can find out as follows:
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the AirPort Express
Click Manual Setup
Click directly on the word Version (3rd line)
If there are any updates, you will be notified.
If there are not any updates, you have already have the latest firmware.

Similar Messages

  • Trouble to connect to wireless G routers after installed the latest update 10.10.2  . Anyone with the same problem? Please help Apple support team!! Macbook Pro mid 2010. PS.: Only with wireless G routers, the rest are fine (N, B...)

    Trouble to connect to wireless G routers after installed the latest update 10.10.2  . Anyone with the same problem? Please help !!! Macbook Pro mid 2010. PS.: Only with wireless G routers, the rest are fine (N, B..., and both radio bands)

    Trouble to connect to wireless G routers after installed the latest update 10.10.2  . Anyone with the same problem? Please help !!! Macbook Pro mid 2010. PS.: Only with wireless G routers, the rest are fine (N, B..., and both radio bands)

  • Numerous problems with Airport Express 802.11n with DSL and extending WLAN

    Hi all,
    I have the following hardware:
    802.11b/g Airport Express with firmware 6.3
    802.11n Airport Express with firmware 7.3.2
    MacBook Pro
    iBook G4
    Mac Pro PowerMac 2x450 G4
    Up until now I had been using the old Airport Express as the base station connecting to my PPPoE DSL line, and it worked fine. I wanted to extend the range of this network, and got another newer Airport Express, the 802.11n model.
    First I tried to use the 802.11n to connect to the Internet and the old one to extend the network. Turns out the old one can't be used to extend a network, which is bad enough, but the 802.11n one refuses to connect via DSL for more than a couple minutes, then drops the Internet connection.
    So I tried downgrading the firmware to 7.3.0 and 7.3.1, but it didn't help. Did a hard reset, factory default reset, soft reset, nothing worked.
    Next I tried swapping the two, putting the old Express back on the DSL line and the new one as the bridge to extend the network (using WPA2). But the 802.11n complains that it can't access the network and flashes amber.
    Again, tried upgrading to 7.3.2, downgrading to 7.3.1 and 7.3.0, hard reset, soft reset. Nothing works.
    Any ideas?
    Cheers,
    Fairfax71

    I don't see any option in the Airport Admin Utility for the old Express for creating a WDS network, only to participate in one...?
    That is the option you want to choose.
    You could use the newer AirPort Utility to configure the older AX.
    Sorry, forgot to ask something else: The 802.11n Express is able to join the WLAN created by the 802.11b/g Express as a client, but not extend it, is that what you're saying?
    No. If you join the network the AX is simply acting as another wireless client and is not extending the network. The "extend" option is not available since the older AX is not 802.11n capable. You must use WDS.
    Use AirPort Utiity and follow these steps for both AX's. To set up the main AX:
    Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
    Open AirPort Utility (located in the Utilities folder in the Applications folder on a Mac, or in Start > All Programs > AirPort on a Windows computer). Select the main base station, and choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary. If the base station is using the default password of public, you will not be prompted for a password.
    Click the Wireless button, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
    Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
    Select the “Allow wireless clients” checkbox if you want client computers to connect to this base station.
    Click the Add button and enter the MAC address of the base stations you want to connect to this base station. If there is a base station listed that you’d like to remove from the list, select the base station and click the Delete (–) button.
    Click Update to send the new settings to the base stations in the WDS. By default, the “Allow wireless clients” checkbox is selected. If you deselect the checkbox, and later want to change the settings on the base station, you must connect to the base station’s LAN port with an Ethernet cable. You will not be able to connect to the base station wirelessly.
    To set up the second AX to connect to the main AX:
    Open AirPort Utility. Select the AX, and choose Manual Setup from the Base Station menu. Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
    Enter the same network password as the main base station, if necessary.
    Click the AirPort button, and then click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
    Click WDS and choose “WDS remote” from the pop-up menu.
    Enter the MAC address of the main base station in the WDS Main field. The MAC address is also referred to as the AirPort ID and is printed on the label on the bottom of the base station.
    Click Update to transfer the settings to the base station.
    This can be found on page 42 of "Designing AirPort Networks Using AirPort Utility" (direct PDF download).

  • How can use my Airport Express 802.11n with IOS X 10.9.4?

    I have two Airport Express unit (802.11n) used to connect my upstairs and downstairs HiFi amps to my music collection (On a Mac mini and on my MacBook).  I keep my software up to date and my Airport Express units have now lost connectivity with my updated computers.  They do not even appear in UTILITIES/AIRPORT UTILITY - so I cannot reconfigure.  I have tried pressing the reset button and have tried "Googling" it but have had no success.  Any suggestions would be gratefully received.

    Both say A1254 (I think)
    A1254 is not a model number for an AirPort Express, but if you meant to say A1264, that is an 802.11n model that is compatible with AirPort Utility on an iOS device and also the Mac running Mavericks (10.9.4).
    If you have pressed the reset button as you say above (held it in for 5-6 seconds or more), then the AirPort Express devices are reset back to factory default settings.
    When you open AirPort Utility on the Mac and click on Other Wi-Fi Devices, you should see the AirPort Express. Click on AirPort Express to start the setup process and follow the prompts.

  • Airport Express 802.11n with Snow Leopard

    Hello everybody.
    I used my Airport alway's with iTunes in 10.5.8 and it worked fine. But now ik have my G5 upgraded with the new Snow Leopard 10.6.1 and now the connection won't work in iTunes 9.0.1(9). The computer sees the Airport and i can change the settings by the Airport configuration program, but when i try to connect it true iTunes it won't work??? If i try to select other speakers in iTunes it jumps back to computer? Please does somebody know's the answer to this???

    But now ik have my G5 upgraded with the new Snow Leopard 10.6.1 and now the connection won't work in iTunes 9.0.1(9).
    I'm curious on how you were able to upgrade your G5 computer with Snow Leopard as the minimum requirement for this OS is an Intel processor.

  • I cannot download the latest update for itunes because it say the file itunes.msi is missing

    I cannot download the latest update for itunes because it says that the file itunes.msi is missing

    Download the Windows Installer CleanUp utility from the following page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
    http://majorgeeks.com/download.php?det=4459
    To install the utility, doubleclick the msicuu2.exe file you downloaded.
    Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
    Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

  • Speed issue with WDS, Airport Extreme, and Airport Express 802.11n

    I have a Airport network set up using WDS and two airport base stations: an Airport Extreme 802.11n, and an Airport Express 802.11n. The Extreme is configured to be WDS main and is connected to my cable modem and other computers, while the express is WDS relay and acts as a switch.
    I don't actually have any wireless clients connecting to the express. I'm using it to connect a mac with no airport card to the network by plugging it into the ethernet port on the express. For the most part, it works, and the mac gets a network address and can access the network. However, the connection speed from the Express to the Extreme seems slower than it should be.
    Since both are 802.11n, and the Mac is plugged into the Express's 10/100 ethernet port, I figure the theoretical top speed that the Mac should be able to communicate with another device plugged into the Extreme is at around the same speeds as 100 mbps ethernet, since the 100 mbps ethernet connection should be the bottleneck in this case. In reality, the speeds are much slower: when I transfer files between a machine connected to the extreme (via ethernet) and my mac, the speed tops out at about 2 megabytes a second, if that.
    I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is! Also, the only wireless communication is between the Extreme and the Express, so one wireless device acting as a relay for another (and thus cutting the throughput in half) shouldn't be an issue.
    Does anyone know why the speeds are so slow, and if there's anything I can do to improve them?

    Hello Brian Kendall. Welcome to the Apple Discussions!
    I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is!
    That is because you established a WDS which only runs in 802.11g. Since you have two 802.11n base station, you would want to take advantage of the "Extend a network" feature available with these base stations.
    Here's a typical setup:
    o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
    o Open AirPort Utility and select the base station that will connect to the Internet.
    o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
    o Click AirPort in the toolbar, and then click Wireless.
    o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
    o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
    o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
    o Enter the base station network and base station password is necessary.
    o Click Update to update the base station with new network settings.
    (ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

  • Airport Express 802.11n not seen in utility scan

    I have an Airport Express 802.11n and the Airport utility scan isn't seeing it.  I've reset it back to factory and still not being seen.  Help please

    After a factory default reset, the AirPort Express is broadcasting a wireless network with a name like Apple Network xxxxxx.
    If you are tying to configure the Express using wireless, you need to make sure that your Mac is logged on to this network first, before you open AirPort Utility.
    It's also possible to connect an Ethernet cable from your Mac to the AirPort Express and then open AirPort Utility. Once the Express has been configured an updated, you can remove the Ethernet cable.

  • Hello everybody, I need to update my ITunes on my MAC (laptop) to the newer version so I can then be able to update the latest updates for my Iphone-3G'S. I don't require a complete reinstall just need to be able to update it.What I have tried so far is I

    Hello everybody, Im trying to update my ITunes on my MAC (laptop) to the newer version so I can then be able to update the latest updates for my Iphone-3G. I don’t require a complete reinstall just need to be able to update my itunes.
    What I have tried so far is I had my MAC search for update’s and it said that I should update to (ITunes version  10 . 6 . 3 ) So I asked it to do the update but after 2hrs of waiting for it to download/update it then puts up a message saying the following- (In order to continue installation, please close the following application: ITunes).
    When I tried to do this another message comes up that says- (The update ITunes can’t be installed. The following install step failed: run preupgrade script for Apple mobile device support. Contact the software manufacturer for assistance.)
    I have also tried to run the update while having closed ITunes before I even start the update but the same problem happens after waiting about 2hrs.
    Some one that had the same problem said this might be happening in the older operating systems. But that does not make sense because surely Apple want customers who own a MAC and i-phone to still buy from iTunes.
    My MAC is about 4-5years old. I have a i-phone.3G, 
    Can anybody help me please and Thank you?

    Download iTunes using the tab at the top of this page. Then run the update with iTunes closed.

  • I have just downloaded the latest update for Pages on my iPad and now it can no longer open up documents in iCloud and then just shuts down. What The.

    i have just downloaded the latest update for Pages on my iPad and now it can no longer open up documents in iCloud and then just shuts down. What The.

    Before the reset quit Pages like this:
    Double click the Home button to show the screen with running and recently used apps. Each app icon will have a sample page above it. Flick up on the page (not the app icon) and the page will fly away and the app icon will disappear. This quits that app.

  • What is the latest update available for Mac OSX 10.5.8 that will allow me to get the latest update for iTunes.  I really need to update my iPhone and CAN'T!!  GRRRR!!!

    What is the latest update available for Mac OSX 10.5.8 that will allow me to get the latest update for iTunes.  I really need to update my iPhone and CAN'T!!  GRRRR!!!

    Minimally you need Snow Leopard or greater:
    Upgrade Paths to Snow Leopard, Lion, and/or Mountain Lion
    You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99. To access the App Store you must have Snow Leopard 10.6.6 or later installed.
    Upgrading to Snow Leopard
    You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard — Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
    After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
         Snow Leopard General Requirements
           1. Mac computer with an Intel processor
           2. 1GB of memory
           3. 5GB of available disk space
           4. DVD drive for installation
           5. Some features require a compatible Internet service provider;
               fees may apply.
           6. Some features require Apple’s iCloud services; fees and
               terms apply.
    Upgrading to Lion
    If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
    You can purchase Lion by contacting Customer Service: Contacting Apple for support and service — this includes international calling numbers. The cost is $19.99 (as it was before) plus tax.  It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
         Lion System Requirements
           1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
               or Xeon processor
           2. 2GB of memory
           3. OS X v10.6.6 or later (v10.6.8 recommended)
           4. 7GB of available space
           5. Some features require an Apple ID; terms apply.
    Upgrading to Mountain Lion
    To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
         OS X Mountain Lion — System Requirements
           Macs that can be upgraded to OS X Mountain Lion
             1. iMac (Mid 2007 or newer) — Model Identifier 7,1 or later
             2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) —
                 Model Identifier 5,1 or later
             3. MacBook Pro (Mid/Late 2007 or newer) — Model Identifier 3,1 or later
             4. MacBook Air (Late 2008 or newer) — Model Identifier 2,1 or later
             5. Mac mini (Early 2009 or newer) — Model Identifier 3,1 or later
             6. Mac Pro (Early 2008 or newer) — Model Identifier 3,1 or later
             7. Xserve (Early 2009) — Model Identifier 3,1 or later
    To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
    Are my applications compatible?
             See App Compatibility Table — RoaringApps.
         For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion.

  • What is the latest update for ipod 4g

    i want to know what the latest update for ipod 4g

       Update 6.1.3 is the latest and will be the last!

  • What is the latest update for captivate 6

    What is the latest update for captivate 6 and problems does it fix?

    Is there a way to install the Captivate 6.1 update for a normal Captivate 6 user? (I  mean not a 'Subscription customer' or a
    'Adobe Software Assurance customer')
    I am very interested in this update.

  • What is the latest update for OS?

    what is the latest update for OS and where can i get it from on my mac?

    Mac OS X Mountain Lion is the latest updaye, unfortunetly It is not available in the Apple Store but in the mid-July is will be announced in the Apple Store and everywhere.

  • I installed the latest update for itunes on my windows vista machine, and now itunes wont open at all

    could you give me a hand? i downloaded the latest update for i tunes, and now im facked. i cannot open itunes. ive deleted and uploaded the new one as it says to in the 'support' section, all to no avail.

    Do you get an error message when you try to launch iTunes? If so, what does it say? (Precise text, please.)

Maybe you are looking for

  • FTP Adapter Unable to change directory 'inputDir'

    Hi all. I'm trying to put the file into BPEL Process, transform and put it to the output directory like in tutorial 129.FTPAdapter FTPDebatching. But I've got this message: <bindingFault xmlns="http://schemas.oracle.com/bpel/extension"> <part name="c

  • Ora 12801 with rep 1401

    dear all how are you ??? i am just need some help cuz i have an application when the genarate report an error accuorred says : Rep -1401: ' report_name' fatal PL/SQL error accurred Ora - 12801 : error signaled in parallel query server Notcied that bo

  • Can't accept terms

    I have an Adobe ID and am trying to login to https://creative.adobe.com/join/starter?promoid=KAMVZ  I see the terms, but there is no link to accept??? Can't go further. I've tried in FF and Chrome.

  • How come every time I open certain apps, my imac gives me an internal error message then it crashes?

    I dont understand it and I'm hoping that someone out there might be able to, Thank you ....eddyy

  • 11.5.4 to 11.5.5 Upgrade

    How long does this upgrade and testing usually take. Our ASP required our ERP system be down for 6 days, 4 days to apply upgrade and 30 CRM pathces...2 days for testing. Is this the industry norm?