HT201066 Using us-144 mkII (USB interface) with Quicktime

Does anybody know how I can get my MacBook Air to recognize my USB interface when I use Quicktime?
Quicktime input options are limited to internal mic and my cam... won't recognize my USB interface, even though its appearing in the computers' audio preferences.
HEEEEEEEELP!!!
Thanks!
Eddie

foxyroxyD wrote:
digital piano - midi in/out - audio interface - usb - Macbook.
check the cabling:
http://www.bulletsandbones.com/GB/GBFAQ.html#controllertointerface
(Let the page FULLY load. The link to your answer is at the top of your screen)

Similar Messages

Suggestions on firewire/usb interfaces with 16ch of adat lite pipe

hey guys,
I recently bought an rme fireface 800 and am not too happy with it. looking for a firewire or usb interface with at least 16 channels of adat. can't use any pci options like 2408 because slots are full.
thanks
ej

convertors on the fireface aren't anywhere close to my apogee stuff, digi 192 or the da convertor on the presonus central staion for that matter. did small shoot out between fireface vs apogee da16 vs central station. Fireface was by far the worst of the bunch. Thought it was just me and called a friend who has a ff and a cs. he said the that ff sounded like "pooh: running analog through the central station but sounded great being connected directly to speakers. all of my other convertors sound great coming through the cs (digi 192, apogee trak 2, apogee da 16) but fireface doesn't. all were clocked off of apogee big ben and all were using moogami or monster cable. So the logical conclusion would be that the fireface d/a convertor aren't that good.
In thinking about it maybe the fireface might only sound good when it is using its own clock and doesn't like big ben (I haven't tried that yet). I suppose I could reconfigure things so that when I'm using logic the fireface is the master for everything but I run pt and logic at the same time and would rather not.
It just seems to be a waste to only use the fireface for it's 16ch of adat and routing matrix...but it looks like I might not have a choice.
any insights, comments or suggestions are welcome.
thanks,
ej

When to use abstract classes instead of interfaces with extension methods in C#?

"Abstract class" and "interface" are similar concepts, with interface being the more abstract of the two. One differentiating factor is that abstract classes provide method implementations for derived classes when needed. In C#, however,
this differentiating factor has been reduced by the recent introduction of extension methods, which enable implementations to be provided for interface methods. Another differentiating factor is that a class can inherit only one abstract class (i.e., there
is no multiple inheritance), but it can implement multiple interfaces. This makes interfaces less restrictive and more flexible. So, in C#, when should we use abstract classes
instead of interfaces with extension methods?
A notable example of the interface + extension method model is LINQ, where query functionality is provided for any type that implements IEnumerable via
a multitude of extension methods.

Hi
Well I believe Interfaces have more uses in software design. You could decouple your component implementing against interfaces so that
you have more flexibility on changing your code with less risk. Like Inversion of Control patterns where you can use interfaces and then when you decide you can change the concrete implementation that you want to use. Or other uses for interfaces is you could
use Interceptors using interfaces (Unity
Interceptor) to do different things where not all of these is feasible or at least as straightforward using abstract classes.
Regards
Aram

Can I use the lightning to USB cord with any USB/AC adapter?

Just got a new IPhone 5. Can I use the lightning to USB cord with the AC adapter I had for my IPhone 4 (or any other USB to AC adapter)?

Yes I just check and the one for my MacBook fits my 12 Watt iPad charger.

How to use USB interface with LabVIEW Embedded for ARM

Hi everybody.
I am developing an application based on the "LabVIEW Embedded for
ARM". Now I am doing various tests using
the evaluation board 2300 (with NXP LPC2378), but soon I will
dedicate to program the micro used in my project (NXP
LPC2148).
During the tests, I have seen that "default" LabVIEW interface allows the use
of CAN, I2C and SPI interfaces of the micro. I want to know how can I also use the
USB interface that is on the micros -both LPC2148 and LPC2378- (pin USB_D + / D-, USB_UP_LED,
USB_CONNECT, VBUS).
Thanks in advance for your suggestions

@chueco85
If you've created an application in LabVIEW for ARM and you build it.
you can go to tools >> ARM Module >> Show Keil uVision
then go to he build options.
the hex file will be created when you do a build.
with flash magic :http://www.flashmagictool.com/
you can program your device.
Wouter.
"LabVIEW for ARM guru and bug destroyer"

Using journalized data in an interface with aggragate function

Hi
I am trying to use the journalized data of a source table in one of my interfaces in ODI. The trouble is that one of the mappings on the target columns involves a aggregate function(sum). When I run the interface i get an error saying "not a group by expression". I checked the code and found that the jrn_subscriber, jrn_flag and jrn_date columns are included in the select statement but not in the group by statement(the group by statement only contains the remiaining two columns of the target table).
Is there a way around this? Do I have to manually modify the km? If so how would I go about doing it?
Also I am using Oracle GoldenGate JKM (oracle to oracle OGG).
Thanks and really aprreciate the help
Ajay

'ORA-00979' When Using The ODI CDC (Journalization) Feature With Knowledge Modules Including SQL Aggregate Functions [ID 424344.1]
Modified 11-MAR-2009 Type PROBLEM Status MODERATED
In this Document
Symptoms
Cause
Solution
Alternatives :
This document is being delivered to you via Oracle Support's Rapid Visibility (RaV) process, and therefore has not been subject to an independent technical review.
Applies to:
Oracle Data Integrator - Version: 3.2.03.01
This problem can occur on any platform.
Symptoms
After having successfully tested an ODI Integration Interface using an aggregate function such as MIN, MAX, SUM, it is necessary to set up Changed Data Capture operations by using Journalized tables.
However, during execution of the Integration Interface to retrieve only the Journalized records, problems arise at the Load Data step of the Loading Knowledge Module and the following message is displayed in ODI Log:
ORA-00979: not a GROUP BY expression
Cause
Using both CDC - Journalization and aggregate functions gives rise to complex issues.
Solution
Technically there is a work around for this problem (see below).
WARNING : Oracle engineers issue a severe warning that such a type of set up may give results that are not what may be expected. This is related to the way in which ODI Journalization is implemented as specific Journalization tables. In this case, the aggregate function will only operate on the subset which is stored (referenced) in the Journalization table and NOT over the entire Source table.
We recommend to avoid such types of Integration Interface set ups.
Alternatives :
1.The problem is due to the missing JRN_* columns in the generated SQL "Group By" clause.
The work around is to duplicate the Loading Knowledge Module (LKM), and in the clone, alter the "Load Data" step by editing the "Command on Source" tab and by replacing the following instruction:
<%=odiRef.getGrpBy()%>
with
<%=odiRef.getGrpBy()%>
<%if ((odiRef.getGrpBy().length() > 0) && (odiRef.getPop("HAS_JRN").equals("1"))) {%>
,JRN_FLAG,JRN_SUBSCRIBER,JRN_DATE
<%}%>
2. It is possible to develop two alternative solutions:
(a) Develop two separate and distinct Integration Interfaces:
* The first Integration Interface loads data into a temporary Table and specify the aggregate functions to be used in this initial Integration Interface.
* The second Integration Interfaces uses the temporary Table as a Source. Note that if you create the Table in the Interface, it is necessary to drag and drop the Integration Interface into the Source panel.
(b) Define two connections to the Database so that the Integration Interface references two distinct and separate Data Server Sources (one for the Journal, one for the other Tables). In this case, the aggregate function will be executed on the Source Schema.
Show Related Information Related
Products
* Middleware > Business Intelligence > Oracle Data Integrator (ODI) > Oracle Data Integrator
Keywords
ODI; AGGREGATE; ORACLE DATA INTEGRATOR; KNOWLEDGE MODULES; CDC; SUNOPSIS
Errors
ORA-979
Please find above the content from OTN.
It should show you this if you search this ID in the Search Knowledge Base
Cheers
Sachin

So What's the Consensus on USB Interfaces with Logic?

Digidesign's new ELEVEN Rack has a coreaudio driver and therefore can be used as a main interface. This is good news for those who like to use both Logic and Pro Tools, perhaps depending on the project, or to track in Logic and mix in PT.
But, Digi has chosen to make the Eleven Rack a USB interface. Some people on the DUC are not pleased about this and claim this will mean low track counts and all manner of horrors. I worry about it too. Digi went from the Mbox which was USB to the MBOX II Pro which is Firewire, and Ensemble and all the other top interfaces are firewire. Digi's answer seems to be that Firewire is going the way of the buffalo.
Does anyone have any real data on whether a USB interface will result in poorer perfomance?
Thanks
Tom

As FW is approx 5x faster than USB It will mean lower track counts, but as the Eleven rack is a guitar processor, I'm sure Digi aren't marketing it as a multitrack audio interface.
FTR: I went and had a listen to the Eleven and I wasn't all that impressed to be honest, the new Logic amp designer and pedals are far more realistic.

Using old charger and USB cable with new 755

Just purchased a 755p from Verizon. I've used a Tungsten E2 for a long time and was wondering if I can use my old charger and USB cable with the 755p.
Post relates to: Treo 755p (Verizon)

They are compatible.
Post relates to: Palm TX

Using a mtech hiface usb device with macbook air is producing a lot of static. when i touch the mac air it stops then starts when i remove my hand. Help?

Im using a mtech hiface usb device for audio on my Mac Air. If i disconnect it from its ac and disconnect the hiface from the usb then take the Mac Air to a new location to work then return it I have an awful lot of static. im assuming its static electricity from the move or something. ive tried to ground it with my body by touching the mac air while touching something grounded. The static stops at that point but starts all over when i move my hand away from the computer. Any suggestions, could it be a setting in the USB? Thanks.

how long have you had your ipod? mine did the same but after a while you need to get a new one because of the battery...

? on Using which format of Audio Interface with a Imac i3

Hi,
I have been reading and reading about this topic. My (R.I.P.) eMac has been replaced by a very nice and fast Intel i3 Imac with FW800 and plenty of USB 2.0 and SP/Dif (even)
Fortunately most all of any music gear that needed driver or firmware updates for Snow Leopard had them available, but my Tascam US-120 (USB 1.1) does not so have been looking at USB 2.0 (though its amazing how many USB 1.1 USB Audio Interfaces are still be produced and at $$$ prices. Firewire Audio Interfaces are at FW 400 and with a Firewire 800 port on the back of the iMac appears ? that a interface cable is the required or ? only way to use a Firewire interface 1) I want to make sure I am understanding this correctly, and 2) is this safe ? to do 3) I am getting a FW 800 Extrenal Hard Drive so that is a match, 7200RPM,
I do plug in to the Interface (or did) at times 2 microphones XLR type (to put mic's on a amplifier) , a Electric Guitar , or a Acoutsic Electric Guitar in to the interface or record it with a mic's, I have a MIDI Keyoard that has MIDI in-out as well as USB in, and also plugged two power monotors(Linear Flat Speakers) in to the out puts of the previous Audio Interface.
Last Question I reviewed the bit/kHz of the USB 1.1 interfaces and they range from 16 bit//48 kHz,24bit 44.1kHz, to 24bit 48kHz to 24bit 96kHz (on a USB 1.1 connection from the particular USB audio Interfaces when you find a USB 2.0 modem the max bit rate is 24 and the kHz (ranges from 96 kHz to 192 kHz) I am not a electronics genius
but have recorded music in to computers for over 6+ years and the Resolution rates of the USB 1.1 do not make sense to me (I realize that MP3 (being compressed) and CD quality recordings are only so high but..
I am going to (later) update to Ilife 11 with Garageband 11' which can record up to the 24 bit range so that is a consideration as well
The FW 400 resolution rates in the chart I have are a minimum of 24 bit and kHZ range of 96 kHz to 192 kHz . and in theory USB 2.0 is a bit faster at 480 mbs versus FW 400
at 400 mbs and from what I have learned USB 1.1 is slowest, I guess I am missing something, over thinking this or. Just want to do it safely, and get all of the inputs and out puts I need (I can even use the SP/Dif that comes on alot of Audio Interfaces, The AES Audio Engineers Society just wrapped up a convention and have been looking at their site and new product releases.
Any Input would be greatly appreciated and I wish I could write less and explain more!
David
ambienttales

If you can stretch your budget (quite a bit actually, but you can find deals on the net) I can't recommend the RME Fireface 800 models enough. Lots of I/O, never EVER had a crash, and the drivers and tools are rock solid. RME also makes a FF400 which has less I/O, but also costs less. The sound is steller, and it has no discernable noise. These are Firewire interfaces, but they just camme out with one that also talks USB.
Pete

Anyone Using Eleven Rack as an interface with Logic?

Just wondering if the USB aspect of Eleven would have trouble with sessions in Logic with large track counts...
Thanks
Tom

Spelldoggy wrote:
I recently purchased Logic Pro and understood that I could use my pro tools LE 002 running 7.4 as an interface. It won't record audio no matter what I do although I know it's possible because it worked once. I've heard that pro tools core audio won't work with 10.4.11 Is this true?
Hi,
I'm Running :
MacBook Pro 15"
Model Identifier: MacBookPro2,2
Processor Name: Intel Core 2 Duo
Processor Speed: 2.16 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache (per processor): 4 MB
Memory: 2 GB
Bus Speed: 667 MHz
Boot ROM Version: MBP22.00A5.B07
SMC Version: 1.12f5
Mac OS 10.4.11
ProTools Le 7.4.cs3
Digidesign Digi002 Rack. Software version 0x1 Spec Id 0xA4
Logic Pro 8.0.1
This WORKS. So, you need to ensure you have ALL the correct software versions for your computer.
Cheers

How do I use more than one USB device with Airport Extreme?

I would like to plug a shared hard drive into my new airport extreme and still be able to plug in a shared printer as well. How am I supposed to do this with only one USB port. Do I use a USB hub???
Is it possible to connect a hard drive using one of the ethernet ports?

To use multiple USB devices you would use a powered USB hub.
You can connect a hard drive to one of the Ethernet ports providing the hard drive is a NAS and supports Ethernet connections. In that situation the NAS hard drive is just like any other Ethernet client and the AirPort Extreme base station (AEBS) does not handle the file sharing services. The drive itself would provide the file sharing services.

What's a good voice recording app I can use on my laptop and interface with iTunes?

Does anyone have a great recommendation for making home-made voice recordings that I can post on social media using iTunes? Is there a particular app/recorder that makes it sound more professional than a home-made job?
Thanks.

You can't plug a microphone directly into a Mac: you have to go through a mixer or a preamplifier to bring the voltage level up to the Mac's input level. Of course this doesn't apply to USB microphones, which can be plugged into a USB socket and will usually work straight off. The Mac's own microphone may be reasonable sounding - you can try and see what it sounds like - but obviously you musn't touch the Mac while recording and you will get better results with a decent external mic. (USB would probably be best, but they're not cheap.)

Any issue using Time Machine on USB drive with AirPort?

Are there any issues using a USB drive attached to an AirPort Extreme with Time Machine? My guess is no, but figured I would ping the forum and see if there's something I have not thought of. I know Time Capsule does this, but I don't have that - I have an AirPort Extreme.
The drive is within my network and not exposed to anyone unless they can connect
My password is required to access the Time Machine files
Any security implications not covered by these two points?
I'm currently using a USB drive I attach/detach from my MacBook Air and it would be much more convenient to backup to the drive connected to the AirPort. The first backup will probably take a day short of forever being over the air and not the wire, but after that I imagine it would nicely run in the background.
Thanks for any feedback or suggestions!

Are there any issues using a USB drive attached to an AirPort Extreme with Time Machine? My guess is no, but figured I would ping the forum and see if there's something I have not thought of.
The correct answer is yes. First off, Apple does NOT support Time Machine backups to external USB HDDs attached to the AirPort Extreme ... although they do for the Time Capsule.
Please check out this excellent Pondini article which provides some details on why this would not be a good idea.

Using 2 or more USB instruments with Logic Pro

I recently purchased a Korg M3 (which is great). I'm considering adding a Motif XS rack.. My question, are any Logic Users out there using Logic Pro with two or more USB instruments connected?
Are there any issues with that (other than assigning to different MIDI channels)? Does USB bog down when there is too much data?

I'm only using these three lines of code. If they don't work, neither will any more lines.
I discovered the issue thought. If I read two different fields from the same user-defined table then it works. If I read from two different user-defined tables I get the error. Apparently B1 can't handle parameters being set from two different ud tables.
This works:
DECLARE @S2 nvarchar(30), @S3 nvarchar(30)
SELECT @S2 = (SELECT T0.U_Country FROM [dbo].[@COUNTRIES] T0 WHERE T0.U_Country = '[%2]')
SELECT @S3 = (SELECT T0.U_CCode FROM [dbo].[@COUNTRIES] T0 WHERE T0.U_CCode = '[%3]')
While this does not:
DECLARE @S2 nvarchar(30), @S3 nvarchar(30)
SELECT @S2 = (SELECT T0.U_Country FROM [dbo].[@COUNTRIES] T0 WHERE T0.U_Country = '[%2]')
SELECT @S3 = (SELECT T0.U_AdCode FROM [dbo].[@BPGROUPS] T0 WHERE T0.U_AdCode = '[%3]')
Alan

HT201066 Using us-144 mkII (USB interface) with Quicktime

Similar Messages

Maybe you are looking for