HT201177 i have a mac book, and I squeezed My screen too hard and it broke.Are these difficult to replace?
I have a Mac Book, and I squeezed the screen too hard, and it broke, Is this a difficult fix?
You can get the screen replaced on a White or Black non-unibody MacBook for $139 by mail. http://www.ebay.com/itm/13-APPLE-MacBook-LCD-Screen-Repair-Replacement-Service-/ 270597769033?pt=LH_DefaultDomain_0&hash=item3f00e24749
Similar Messages
-
Please can you help me? I have a Mac Book Pro with OS X 10.7.4 and my FaceTime doesn't open anymore. It appears this sentence:"the server detected an error during the elaboration of the registration. Please try later". What happens??
Start the computer from the installation disk and perform Repair Disk and Repair Permissions using Disk Utility
-
I have a Mac Book Pro - HELP - problems with bootcamp = too full
I have have a Mac Book Pro. My drive is full. Sadly I had the partition set up at a store that should have known what they were doing (NOT an apple store, but a certified store that carries only Apple products), anyway.. I am now at the point where my bootcamp is full. I've tried reading a number of posts, but some things apply to me, some things don't so here is my situation:
Mac Book Pro
OS X 10.8.2
Processor: 2.53 GHz Intel Core i5
Memory 4 GB 1067 MHz DDR3
Startup Disk: Macintosh HD
Using Bootcamp with Windows 7
I purchased Camptunes by Paragon and tried repartioning my drive that way. It looked like it was going to work until the following error message happend:
Windows filesystem verification failed. Please, repair Windows volume and try again. Windows is not letting me do this because I don't have enough room. Round and round the problem goes.
Initially when I was trying to clear out my Windows side I found a bulky .NET program I wanted to delete. It would not delete it for me (I can retry to look for that error message), but essentially it wouldn't delete it at all. I have no temporary internet files I can delete, cookies or other programs (except my printer drivers), but essentially - I can't figure out what to do next.
I read another post about a person who didn't want to backup their files first. This is not me. I do back up to a LACIE back up drive that has a 999.86 GB capacity with 872.11GB free. What I want to know is do I have to buy another back up to keep it all completely separate? What other program do you recommend to create a virtual drive? Can I get a step by step on what to do? I have the original windows disk if that helps in the equasion.....
My head hurts.... help!interenet wasn't working properly and i couldn't finish
Try restarting while holding down the Option key. That should prompt the startup manager window where you can select the startup disk and reboot.
Then try reformatting (erase) using OS X Recovery About OS X Recovery
Keep in mind, Apple does recommend a high speed broadband internet connection for OS X Recovery. A slow connection may time out before recovery is finished. -
Mac book pro start up, white screen pops up and it don't process any further! Can anyone help?
When my laptop was updating the software it was stuck on installing the updates. I held the power button then turned the laptop back on! It makes the on sound but stay on the white screen! Can anyone help?
Hey Antonioaok,
Welcome to the Apple Support Communities. If you are getting the white screen when you start up, there are a few steps that can be done. The first one would be resetting your NVRAM
About NVRAM and PRAM
http://support.apple.com/kb/HT1379
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
The next step, if it does not boot to your operating system would be to attempt to boot into safe mode. These steps are also based on the fact that your profile states you are running Snow Leopard.
Mac OS X 10.6: Starting up in safe mode
http://support.apple.com/kb/PH6455
To start up in safe mode:
Shut down your computer and wait 10 seconds.
Press the power button.
Immediately after you hear the startup tone, hold down the Shift key. You should press the Shift key as soon as possible after you hear the startup tone, but not before.
Release the Shift key when you see the gray Apple logo and progress indicator (spinning gear).
To leave safe mode, restart the computer normally without holding down any keys during startup.
If after that, you were still not able to get into your operating system, the last step would be trying to reinstall the operating system.
Mac OS X 10.6: Reinstalling Mac OS X
http://support.apple.com/kb/PH6606
Regards,
-Norm G. -
From the "date and time" I tried to drag the month and year to my menu bar. It did not stay, so I did it several times, but to no avail. I closed the window and went back to my Thunderbird email only to find that the date I tried to use became the date in the "date received" column of all of my emails from back to 2011. I changed the date a few days later, and then the date changed on all of my emails. I would like to undo whatever I did to the dates so that the emails show when they were originally received. I did manage to get "the order received" which helps a little, but I cannot see the original dates.
I have checked "Set date and time automatically" but it doesn't change the dates on my saved emails.I at first thought it might be a Mac thing, but I couldn't find a solution. I realized that the date only affected my email, so then I thought it must be a Mozilla problem.
-
I have a mac book pro I want to use 2 monitors and have garageband open with 2 projects is this possible?
GarageBand can open only one project at a time. Project are treated differently from audio files; you can have many audio files open in QuickTime or other audio players, but GarageBand will always close the current project when you open a new one.
If you have the newest GarageBand 10.0 and the previous version, GarageBand '11, version 6.0.5, you can open one project in GarageBand 10.0 and one project in GarageBand '11.
However, you cannot drag and top between the windows or transfer media. And once a project has been converted to GarageBand 10 format, it can no longer be opened by GarageBand '11. -
Mac Book Pro with Yosemite 10.10.1 software and a HP Photosmart C4599
Hello I have a Mac Book Pro with Yosemite 10.10.1 software and a HP Photosmart C4599 All in one printer and I am unable to install my printer, it will print when cable is connected but I cannot add it wirelessly. i have checked for software updates but none are available.
Hi,
A software for a such is no longer available however you may set a wireless connection by following the workaround below:
Step one: Restore the network defaults:
1. Press the Wireless button on the product.
2. Press the button next to the down arrow on the display until Restore Network Defaults is highlighted, and then press OK.
3. Confirm that you want to restore the network defaults.
Step two: Turn the wireless radio on:
1. Press the Wireless button on the product.
2. Press the button next to the down arrow on the display until Turn Radio On is highlighted, and then press OK.
Step three: connect the Mac to your printer:
1. From the Mac click the WiFi icon and then click on Join Other Network.
2. Click on Show Networks and connect to the listed HPSETUP network.
Step four: connect the printer to your wireless network via the EWS interface:
1. Open Safari.
2. Click the Safari menu and then click Preferences.
3. From the Advanced tab, check both of the checkmarks under "Include Bonjour" and press OK.
4. click Bonjour from the top menu, then select the printer to load its EWS page.
5. Click on Networking, then click the Advanced tab.
6. Type the wireless network name as SSID.
7. Select the Infrastructure option
8. Select the correct security type as WEP Encryption or WPA-PSK Authentication and type the password of your router.
Note: If you are not sure about the SSID and the security type, click the WiFi icon on your Mac and select Open Network Preferences.
Click the Advanced button and locate your home network, the Network name aquals to SSID and the exact security type is listed.
Once you are done click on Apply and the wireless light should lit.
Then reconnec tthe Mac to your router, open ystem Preferences > Printers & Scanners and add the printer as Bojour by clicking the plus sign.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution -
I have a Mac Book Pro with a 320hdd, 2.33 processor, 8 gigs of RAM and OS X 10.9.4 . My hdd crashed and I cannot access it so is it possible to install a 1 terabyte drive with the operating software already installed and also upgrade my RAM to 16 gigs?
If I were you I'd install a small SSD as the boot drive from OWC:
http://eshop.macsales.com/shop/SSD/OWC
Then put a second large conventional drive either in the optical bay (Data Doubler) or in an external.
You don't say which MBP you have: Size, CPU type.
Also when you upgrade you could see if you can salvage your data from your old HD. Can you hear it spin up? If so Data Rescue IV. -
My wife and I have 2 new iPhones and also have a mac book pro and an iMac. How can we share apps, music and contacts between all these?
Use the same Apple ID and password for purchasing in all these devices.
-
I have a Mac Book air 11". Normally at home I connect this to a large Thuderbolt Screen. When booting up it some times gets confused and offers me a low resolution result, but some plugging and unplugging of the screen fixes this. I assume it sometimes "sees" the big screen and sets the resolition accordingly. Sometimes does not. But now... I am away from big screen and cannot get the Macbook air on its one to deliver anything other than really poor resolution. I ahve done displays and chosen all three - but no better. And I have said Choose the Best ONe... again not luck. Any ideas. I read in back posts this was a problem a few years ago.
Welcome to Apple Discussions
I believe you have a failing GPU (aka Video Card). Run AHT and see what it tells you. Do not be afraid to run it up to three times in succession if at first it does not detect an error (sometimes errors that are caused by overheating will not show up until the computer is stressed enough - repeating AHT will do that).
As an aside - the MBA was not designed to take the place of a desktop. If you are powering your MBA by leaving it permanently attached to the thunderbolt port on the monitor you are shortening your battery life. -
Hello,
I am trying to connect my laptop to my TV. The computer flashes blue after I plug the cable in but the TV says there is no signal.
I have a Mac Book Pro 2009 and a Samsung 32" Class (31.5" Diag.) 450 Series 720p LCD HDTV (2010 model).
I am using a mini display port to VGA adapter. I have sucessfully hooked up boh devices but it stopped working after a handful of times. I was wondering if there is anything I can do to fix the problem or is my cable broken?Some things you can try.
Startup Issues - Resolve
Startup Issues - Resolve (2) -
I have a Mac Book Pro with 10.6.8 and want to back up my files using a flash drive. It says I did it but when I tried to check on my other Mac - an I Mac with 10.5.8, thedata does not seem to be there. I cant see photos, etc.. It shows the backup as a file and shows various system info. but there are no photos or other files shown.
Thanks for any advise.
MikeA PowerPC Mac, if that's what it is, won't be able to see an Intel Mac's formatted data. Also ExFat formatting is not supported by 10.6.3 or earlier. I would try viewing the backup on another Intel Mac with at least 10.6.4. If it isn't there, then the backup never really took place. I much profer a hard drive with Carbon Copy Cloner.
-
I have a mac book pro with retina,I haven't turned it on in a couple of months.no problems then, now when I try to turn it on i only get apple logo and progress bar. After a few mins the laptop just turns off and nothing eles.any help would be appreciated thanks
I linked to it above, but here is another link.
http://support.apple.com/en-us/HT201262 -
I have a mac book pro. Yesterday the mail app failed to open. I have tried to open it from the dock and the application folder but nothing happens. Does anyone have any suggestions to get it to work?
You don't need iDVD unless you are going to make DVDs. If you are just trying to share files, iDVD won't help you at all.
What you want to do is in iMovie, choose File/Share/File, and export that way. It creates an .mp4 file that should be readable on Macs or Windows.
You could also File/Share/YouTube if you don't mind posting them to YouTube, because of course YouTube videos are watchable by any Mac or Windows computer made in the last 10 years. -
I have a mac book pro and have already downloaded adobe flash player. However when i go to watch a video it says "Blocked Plug In". But my adobe is already up to date. Can someone help me to fix this so i can watch videos?
If you're sure you've installed the latest version of Flash, take each of the following steps that you haven't already tried. After each step, relaunch Safari and test. For a "missing plug-in" error, start with Step 7. Back up all data before making any changes.
Step 1
You might have to log out or reboot before a Flash update takes effect.
Step 2
In the Safari preference window, select
Privacy ▹ Remove All Website Data
Close the window. Then select
▹ System Preferences… ▹ Flash Player ▹ Advanced
and click Delete All. Close the preference pane.
Step 3
If you're only having trouble with YouTube videos, log in to YouTube and load this page. You may see a link with the text "Leave the HTML5 Trial." If so, click that link.
Step 4
If you get a warning of a "blocked" or "outdated" plug-in, then from the menu bar select
▹ System Preferences… ▹ Flash Player ▹ Advanced
and click Check Now. Quit and relaunch the browser.
If the warning persists, triple-click anywhere in the line below on this page to select it:
/System/Library/CoreServices/CoreTypes.bundle/Contents/Resources
Right-click or control-click the highlighted text and select
Services ▹ Open
from the contextual menu.* A folder should open. Inside it, there should be a file named "XProtect.meta.plist". If that file is missing and you know why it's missing, restore it from a backup or copy it from another Mac running the same version of OS X. Otherwise, reinstall OS X.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
Step 5
Open this folder as in Step 4:
/Library/Internet Plug-Ins
Delete the following item, or anything with a similar name, if present:
Flash Player (failing).plugin
You may be prompted for your login password.
Step 6
Re-download and reinstall Flash. Download it from the domain "get.adobe.com". Don't click a link from any other website, including this one, because you can't trust links. They may be an attempt to trick you into installing malware masquerading as Flash. Type the address into the browser window. Never download a Flash update from anywhere else.
Step 7
If you get a "missing plug-in" error, select
Safari ▹ Preferences... ▹ Security
from the Safari menu bar and check the box marked
Allow (or Enable) plug-ins
Then click the button marked
Manage Website Settings...
if present and make sure that the website is not blocked for Flash.
Step 8
Select
Safari ▹ Preferences... ▹ Extensions
from the Safari menu bar. If any extensions are installed, disable them.
Maybe you are looking for
-
Trying to make sense of AS2 gradient fill matrices
This one will likely interest kglad, but I'm all ears for insight from anyone who digs math. I've been working with gradient fills lately in AS2, which means I've been reading through related entries in the ActionScript 2.0 Language Reference. Here's
-
File transfer into application server
Hi folks. I need to retrieve header records from table MCHB and RESB and transfer it into file. Again for the corresponding header record, i need to transfer item records retrived from table MKOL and LFA1 as well. One file each is to be create per pl
-
Can't Import in anything else then m4a 128 kbps
Obviously, this quality ***** and I can't seem to find the place to set it to import my music in higher quality. Before I know I went to Preferences, then Advanced, then Import, but now it seems that when I go to advanced the option isn't there anymo
-
Hierarchy as Flat Structure through BEx Web
Hello Gurus I want to display a hierarchy as a flat table on the web. I want to see KFs against lowest level nodes, the higher level nodes are included soley to give context. So if my hierarchy is: L1 = A L2 = B L3 = C and my KFs are 1, 2, 3. I want
-
Battery now showing the sign X does t mean battery is dead??
my computer behave strangely lately still have power but switch off like if no mor power and now battery show a cross "X" an don more power, is my battery died on me. Thanks Francois