HT201210 Error (-1) any help or ideas?

Hi There
Trying to update, goes as far as verifying Firmware, then just crashes and says error (-1) any help or ideas?.. Am using an iPhone 4..
Thanks..

Error 1 or -1
This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.

Similar Messages

  • HT201210 Iphone 3gs needs to restore as cannot turn phone on but cannot restore as unknown error 2001 keeps coming up.   I have tried several times on different computers. Any help or ideas?

    Iphone 3gs needs to restore as I cannot turn phone on but cannot restore as unknown error 2001 keeps coming up.  
    I have tried several times on different computers. Any help or ideas? Thanks

    Hi there Katherine,
    I have an article here that addresses this error code and can give you a few more troubleshooting suggestions for this issue:
    Resolve specific iTunes update and restore errors
    http://support.apple.com/kb/ts3694
    Check USB connections
    If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
    Common errors: 13, 14, 1600-1629, 1643-1650, 2000-2009, 4000, 4005, 4013, 4014, 4016, “invalid response”, and being prompted to restore again after a restore completes.
    To narrow down the issue, you can also change up your hardware:
    Use another USB cable.
    Plug your cable into a different USB port on your computer.
    Try a different dock connector (or no dock).
    Add (or remove) a USB hub between your device and computer.
    Connect your computer directly to your Internet source, with no routers, hubs, or switches.
    If you see your error after changing your USB connections, continue to the next section to troubleshoot your hardware.
    Thanks for coming to the Apple Support Communities!
    Regards,
    Braden

  • HT4796 After migrating all of my adobe software (Cs4, cs5, etc.) to my new imac, the software won't open due to many errors. Any help on this?

    After migrating all of my adobe software (Cs4, cs5, etc.) to my new imac, the software won't open due to many errors. Any help on this?

    Welcome to the Apple Support Communities
    Adobe software is conflictive when you use Migration Assistant because their applications don't work properly after migration. If you keep the DVDs or the installers of your software, use them to reinstall all your Adobe applications and they should start working correctly

  • I am having difficulty in printing from my ipad to a Kodak Hero 9.1 WiFi printer. I am using Prin Pro Central as an App. The printer is not recognised on my Ipad. Any help or ideas would be appreciated.

    I am having difficulty in printing from my ipad to a Kodak Hero 9.1 WiFi printer. I am using Prin Pro Central as an App. The printer is not recognised on my Ipad. Any help or ideas would be appreciated.

    Versuche es mal ohne express vi s
    Eine Whileschleife, dessen Zähler Du als Zeitbasis verwendest,
    Sinusfunktionen als Signalquellen, g .....  ups english forum
    Try it without express vis
    a while loop with the index as timebase (multiply by your timestep to get t)
    sinus functions with 2 Pi  t  as signals
    In your vi in every interation of the while loop you generate an array of values where you always pich the same index   ...
     PS: here is my version
    Greetings from Germany
    Henrik
    LV since v3.1
    “ground” is a convenient fantasy
    '˙˙˙˙uıɐƃɐ lɐıp puɐ °06 ǝuoɥd ɹnoʎ uɹnʇ ǝsɐǝld 'ʎɹɐuıƃɐɯı sı pǝlɐıp ǝʌɐɥ noʎ ɹǝqɯnu ǝɥʇ'

  • I am trying to update the extension manager 6.0.8 i am getting an error u44m1p7  any help with that pls

    i am trying to update the extension manager 6.0,8 i get an error (u44m1p7) any help with this issue please

    That the CS6 version
    Extension Manager 6.0.8 update
    December 10, 2013
    Macintosh | Windows
    Photoshop: Basic Troubleshooting steps to fix most issues
    Troubleshoot Update Errors
    Many update errors are caused by missing or modified files required by Photoshop, typically by a disk cleanup utility (Ex: CleanMyMac, MacKeeper, etc). Make sure you have the latest updates for your clean-up utilities or discontinue use.
    Explanations of error codes:
    U = Updater.
    44 = Install Update Error
    M1 = Automatic
    M2 = Standalone mode
    P = Patcher
    6 = Done With Errors
    7 = Installation Failed
    ISSUE: Installation failed. Error Code: U44M1P7, U44M2P7, U44M1P6
    SOLUTION: Run the installer. Reinstall Photoshop CS6 to repair/replace the missing/modified file. Select Help>Updates… to run the updater again. http://helpx.adobe.com/creative-suite/kb/error-u44m1p7-installing-updates-ccm.html

  • I am trying to restore my iphone 3gs to 6.1.3 but i get an error (1618) any help?

    i am trying to restore my iphone 3gs to 6.1.3 but i get an error (1618) any help?

    Hey CALLMEALEX,
    Thanks for the question. I understand you are experiencing issues restoring your iPhone 3GS to iOS 6.1.3, the following article may assist you in resolving this issue:
    iOS: Troubleshooting update and restore issues
    http://support.apple.com/kb/TS1275
    Thanks,
    Matt M.

  • Problem: ipod server could not be contacted, i went to control panel, lan settings, ck'd auto detect and went back to i-tune to update and got the same error message, any help is appreciated

    Error message: Ipod software update server could not be contacted. I went to control panel, lan settings, clk'd auto detect settings and ok. When i went back to i tunes and clk's update, i got the same error. Any help is appreciated.
    Rand221

    See the previous posts on the right side of this page under the heading "More Like This" that have you same error message.

  • Error -25262 - any help here?

    I google'd it and came up with nothing.
    Basically, put in a new hard drive into my laptop and everything is fine, moved everything over including the itunes folder. It sees my music but does not allow me to authorize my computer or even allow me to sign in. When I try, I get the above error.
    Any help please?

    Sounds like an issue with your browser settings, not the site. Also, this is not the proper forum for posting a technical question about the site itself.
    1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
    2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

  • TS4185 When starting Facetime on my MAcBook Pro I receive "internal error?  any help?

    When I start Facetime on my MacBook Pro I receive "internal error. You need to quit and reopen Facetime".  I do this and nothing changes, same error.  Any ideas are welcome.

    Found this and it worked:
    Netdude21
    Re: "An internal FaceTime error occurred. There was a problem with FaceTime. " 
    Mar 28, 2011 11:14 AM (in response to iannuz86)
    I have a solution for your problem, it took a little investigating and work to get FaceTime for Mac working. Here's what I did: Go to the folder /Applications then right click on FaceTime.app go into /Contents/LaunchAgents and look for two files "com.apple.imagent.plist" and "com.apple.apsd-ft.plist" and copy them into your /Home/yourusername/Library/LaunchAgents. If you can't find "com.apple.apsd-ft.plist" do a Google search for it and download it, the name will be "com.apple.apsd.plist.txt", do a cmd-I on it and rename it "com.apple.apsd-ft.plist" put this file in the same folder as "com.imagent.plist", launch FaceTime and if your webcam lights up, your good to go. 
    Hope this helps. 

  • I had a problem with the hard disk on a 2010 macbook pro. Replaced the hard disk with an Hitachi 1TB and when I tried to erase and format It fails with input/output error. Any help much appreciated!

    I had a problem with the hard disk on a 13" 2010 macbook pro. Replaced the hard disk with an Hitachi 1TB disk but when I tried to erase and format, it fails with input/output error and at other times saying unable to allocate memory. Any help much appreciated!

    Zap the PRAM and Reset the SMC, then try again.

  • TS3694 Tried to restore my IPOD and keep getting 1604 errors. Any help?

    I haven't updated my ipod in 3 years because it was such a pain last time I did it and thankfully it came back. But I foolishly attempted it again and now after it was put in the restore mode and Itunes attemps to restore the device I get an error message with 1604. I have gone through the troubleshooting steps, tried different USB ports and get the same result. Any help?

    If as the artical says, uyou tried another computer and another network then make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar          

  • Iphone Restore Problem (Error 1011) Any Help?

    I am (was?) the proud owner of a 25 day old iPhone. Yesterday I got the "unable to make calls need repair" message. I've been trying for hours to get my phone to recover using itunes. It downloads all the all the firmware (version 1.1.4) but just as it is about to finish I get a message
    The iPhone could not be restored, error 1011.
    Any help/suggestions?
    Thanks!

    we might not be thinking of the same notification. when your fone is in sleep mode and you press the sleep/wake button on top, do u always see a message that says something along "Your iPhone cannot make/recieve call. Please visit www.apple.com/support" (Emphasis on that last part.) have you contacted apple? have you reset your iphone. have you tried restarting your iphone (probably) have you tried to restore ion a different computer? i would try all of these before calling apple bc most likely that is what they will have you do.
    i hope im to some help =]
    bryan

  • I just updated to OSX Mountain Lion, ever since I upgraded the progress bar in iCal showing my iCal update status does not move or ever go away? What could possibly be going on? Any help or ideas?

    I haven't found anything in any help menus as of yet. And I'm a recent Mac convert....so I'm still new to how everything works. This is probably alot easier than I am making it....but I don't know how to go about fixing this. Thanks in advance!

    bsorensen,
    Welcome to Apple Support Communities.
    Are you using iCloud?
    If so, go to Calendar>Preferences...>Accounts>Account Information, and delete/re-add your iCloud account information.
    If not, try removing the com.apple.iCal.plist file from your Macintosh HD/Users/yourusername/Library/Preferences Folder. To find that Library folder, use Finder>Go Menu>Depress the "Option" key>Library. Drag the .plist file to your desktop, and log out/in or restart.
    Then go to your Macintosh HD/Users/yourusername/Library/Calendars Folder and remove any files with "Cache" as a part of the file name. Use the same method as listed above to get to the correct Library Folder. Log out/in, or restart and check Calendars for functionality.

  • Reader plugin and form submit function inside a browser. *any help or idea please*

    ok I'm pretty sure this is the wrong place, but i was looking to see if there was an adobe reader plugin for browsers and if so if there is a way to overwrite the default browser pdf viewer setting with the adobe reader viewer, sorta like opening the reader on the site,, maybe hosting a scripted version of acrobat or reader, that when uploaded to the server can be launched as a default pdf viewer inside the site itself.
    Might be simpler to explain the ends i';m trying to achieve here.. I have a application form for a daycare saved as a pdf on the server, but as you know clicking the submit button from the browsers default viewer does nothing.. well i'm looking for a way to change that with out having to code the form or implement a bunch of script and databases.. script i can deal with but i dont want to set up a database that a user would then need to go to in order to acess the submited information.. I want the info once completed in the pdf to be emailed to the end user email address, still in a pdf that he can later on print or save in a folder for later use, I dunno..  but yeah I woulds like to avoid downloading of programs as much as possible..
    How about removing the submit button from the form and placing it on the website getting by the limitations of the default viewers, I guess i'm asking if ther is a way to open a pdf on a site, and edit it on that site and then submit the information on that pdf not threw the pdf itself but the site sorta like a typical contact form built in html, but inside the corrtect boxes would be the attached completed pdf file. i guess i'd need to open a a new page inside of a div layer and then submit the information inside the div,, Mainly the complete pdf file, to the mailto: email.
    *sigh*
    any help would be greatly appreciated.

    You're not going to get that with a PDF form, sorry. A year ago I'd suggest that you look into Adobe's FormsCentral, which allows easy creation and administration of both web and PDF forms, but they have decided to discontinue this service. They have directed customers to similar services such as JotForms, so you might want to look into that.

  • Error Message - Any Help

    Hi need help, keep getting this message when trying to uplaod onto my Shuffle.
    "The Ipod "Sean P McMahon's ipod" cannot be updated. The disk couldn't be read from or written to"
    Any help would be great. Going crazy with having to hear kids on the bus.

    I am getting the same type of problem and this is what I think happened with mine (this is my second it was warrantied in early August although the website states I have expired my 90 free chane for support but not according to my math...)
    anyway I have a Mac Mini at home and get my music synced from there the iPod shuffle was at my office and I ran the battery down by accident, so I thought when I purchased the unit it said I could charge from "any" usb port so I hooked it up to my work PC that has iTunes on it and the computer stated it did not recognize the device and therefore would delete all data, I have reset the unit, tried to update it but now the Mac says it is an unrecognized unreadable disc and I have tried to run daignostics where it states the unit is an iPod with like 900MB of info but it says it can not do anything- so I can't even use the iPod updater...- any suggestions at all out there I have looked up any topic I thought fit and none of those seem to fit but this one....

Maybe you are looking for

  • When connecting an HDMI adapter I get the message This device is not supported by this ipad

    WWhen I connect the adapter vis an HDMI cable to my TV, I see the image of my IPad then I get the error message about not supported and the TV displays No Signal. I have a multifunction adapter that works although the connection on it is fiddly. I Us

  • F10 - create video DVD from recorded TV programme

    When I try to create a DVD from a recorded TV programme on my Qosmio F10 I get the following message- "Media in the CD/DVD drive is not writable by Media Center" I know that the media is writable by the Qosmio under normal windows but under Media Cen

  • Is Geforce 2 vgasave?

    Hi, I'm a newbie at XP clean install and when I look at the display settings XP would use vgasave adapter instead of my nVidia GeForce 2 mx400 card. There are  conflicts that I can see with new nVidia drivers, 30.82 and also 40.xx. When I install the

  • ITunes Video Levels Adjustments

    I imported some videos into iTunes (thru multiple and lengthy conversions in Cleaner & iTunes) to play on my iPod and the black levels are way high. In other words, black looks light gray. Now in QT, you can adjust the contrast of a qt and then re-sa

  • How do I paste a copied filename into the save as window?

    I am used to copying filenames into the save as window ... it is more accurate and mroe efficient than typing them.  When I upgraded to CS1 and CS3, I can not do this, either on Snow Leopard or on Win7.  How do I regain the ability to do this?