HT201210 error shows unknown _1

when update iphone 3gs error shows unknown -1

Take it in to an Apple Store or AASP (Authorized Apple Service Provider) and ask them to check it for you.
Be sure to make an appointment first...

Similar Messages

HT201210 please,I need your help ! I was updating my iphone ios to ios4.2 and then problems begins when it shows that it needs to restore the factory software to I was trying to restore ,but that didn't happen it begins but then it shows unknown error 101

please,I need your help ! I was updating my iphone ios to ios4.2 and then problems begins when it shows that it needs to restore the factory software to I was trying to restore ,but that didn't happen it begins restoring but then it shows unknown error 1015

Stop being impatient.
From the article that the question was posted from:
Errors related to downgrading iOS
The required resource cannot be found: This alert message occurs when your device has a newer version of iOS than what is available in iTunes. When troubleshooting a device that presents this alert message, go to Settings > General > About and check the version of iOS on the device. If it is newer than the latest released iOS version, the device may have a prerelease developer version of iOS installed. Installing an older version of iOS over a newer version is not supported.
Error 1015: This error is typically caused by attempts to downgrade the iPhone, iPad, or iPod touch's software. This can occur when you attempt to restore using an older .ipsw file. Downgrading to a previous version is not supported. To resolve this issue, attempt to restore with the latest iPhone, iPad, or iPod touch software available from Apple. This error can also occur when an unauthorized modification of the iOS has occurred and you are now trying to restore to an authorized, default state.
You cannot downgrade.
If you have a 3GS, you can only install iOS 6.1.3 which is the current version of iOS for the device.

HT201263 my ipad 2 3G crashed while playing an HD movie on iOS 7.1, then it enter into rcovery mode, i tried itunes restore and it fails showing unknown error (27), i retried for about 100 times with no benefit.... any ideas or help please

my ipad 2 3G crashed while playing an HD movie on iOS 7.1, then it enter into recovery mode, i tried itunes restore and it fails showing unknown error (27), i retried for about 100 times with no benefit.... any ideas or help please???

By the way, i am using Windows 7 x64 and updated itunes

Itunes showing unknown error (-208)

itunes showing unknown error (-208) whenever I try to play anything. Any ideas?
Self Designed Mix Windows XP Pro Amd cpu
Self Designed Mix Windows XP Pro Amd cpu

Flashmark, welcome to Apple discussions.
Glad you got it sorted!
Hi Flashmark wonder if you can help me ? New user and just down loaded a track from music store then authorised pc but unknown error (-208) "there was an error in the music store please try again later" keeps coming up... been trying for three days now but still the same message!! Can you Help please ?

ITunes keep showing unknown error 48 while restoring iphone 4s. I've already followed applesupport suggestions of reinstalling iTunes, deleting previously downloaded ipsw on my computer and re-downloading it (countless times!) but still to no avail.

Hi. A very much help needed.
- iTunes keep showing unknown error (48) while restoring my iphone 4s
- I've already re-install iTunes various times
- Already delete previously downloaded 8.3 ipsw and re-downloaded it countless times
- Changed and edited hosts in windows drivers as per shown on guides
but... to no avail!!!!
I am now without any phone to be used.
HELP ME PLEASE

Hello Sean,
It sounds like you are constantly needing to restore your phone because it keeps going into recovery mode. Usually putting a device into recovery mode and restoring it can help isolate an issue to your iPhone hardware if an issue persists afterwards. I would try manually putting it into recovery mode and restoring it 1 more time:
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
If that does not resolve it the symptoms indicate to me that it is a hardware issue causing this to happen and would seek service for it:
iPhone Repair - Other Repairs
https://www.apple.com/support/iphone/repair/other/
Thank you for using Apple Support Communities.
All the best,
Sterling

Hi i can not install itune. There are the error show " Could not open key: Unknown\Components\32A7D634EB632D11CABB00087CCFBB48\DAEC106DF4E2BBB458CC2CA9C46 E3A0C.

Hi,
i can not install itune. There are the error show
" Could not open key: Unknown\Components\32A7D634EB632D11CABB00087CCFBB48\DAEC106DF4E2BBB458CC2CA9C46 E3A0C. Verify that you have sufficient access to that key. or contact your support personal.
I have tried some soution from the similar case to uninstall itune and also related components already but finally the probelm still occured.
Please you help to suggest me what can i do? I need to restore my back up data to the new iphone as the previous one got stolen.
BR,
Sirorath A.

Try the following user tip:
"Could not open key: UNKNOWN\Components\[LongStringOfLettersAndNumbers]\[LongStringOfLettersAndNumbe rs]" error messages when installing iTunes for Windows

Why Firefox not Sync will automatically showing unknown error?

why Firefox not Sync will automatically showing unknown error?

How long has been this happening? Have you tried again?
I will encourage you to use the recommendations on this article whenever Sync returns Unknown errors for a long period of time.
[[Firefox Sync is not working]]
Sometimes it's just as simple as a connection issue between your computer and the servers.

Iphone 5 cant be restored, it shows unknown error -1 while trying to restore and it only display connect to Itune

Iphone 5 cant be restored, it shows unknown error -1 while trying to restore and it only display connect to Itune

Greetings ayokunlefromlos angeles,
Welcome to the Apple Support Communities!
I understand that when attempting to restore your iPhone you receive an error and your iPhone shows the Connect to iTunes screen. To begin troubleshooting, I would suggest manually placing your iPhone in recovery mode and attempting the restore. Please follow the instructions located in the attached article to complete this process.
If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support
Cheers,
Joe

I have many download app and game but these app and games are not install on my ipod show me the error "an unknown error occurred (0xE8008001)" What can i do please solve it

I have many download app and game but these app and games are not install on my ipod show me the error "an unknown error occurred (0xE8008001)" What can i do please solve it

download apps and go to this http://www.apple.com/support/ipod/five_rs/

I phone 4 s restore is showing unknown error 3.

i phone 4 s restore is showing unknown error 3.
please help.

You need to put the phone into recovery mode, then restore, as described in this article:
iOS: Unable to update or restore

I can't upgrade my iphone4 from iOS5.01 to iOS5.1, tried many times, always showed "unknown error 1602", what should I do?

I can't upgrade my iphone4 from iOS5.01 to iOS5.1, tried many times, always showed "unknown error 1602", what should I do?

Error 1600, 1601, 1602: Try the following steps to resolve this error:
Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
Follow the steps listed for Error 1604.
This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
Restore and wait for error 1604.
When prompted, click OK.
Close and reopen iTunes while iPhone remains connected.
iPhone should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.

Iweb showing unknown error when trying to publish

I haven't updated my website in the last couple of months...I've been waiting for all of the kinks to be smoothed out with the new moibleme. Now when I go to publish iweb 'prepares to publish' and then gives me a message "Publish error- an unknown error has occurred" I have no idea what to make of this, could someone help please?

Have you updated iWeb to the latest version, 2.0.4? Have you tried publishing to a folder? It that works then the site files are OK and it's a MMe connection issue.

When i am updating any software they ask 4 the password And when i enter the right password downloading starts but it shows unknown ERROR

When i am updating any software they ask 4 the password And when i enter the right password downloading starts but it shows unknown ERROR

Try this article (disable firewall)
http://support.apple.com/kb/TS2799

Lpq outputs print jobs + error T: unknown: moving-to-paused +

Dears,
I have setup remote printing, printing from the client show the print queue at print server(T) however command does not get executed and it outputs
print jobs + error "T: unknown: moving-to-paused"
When is triggered lpstat command before printing
# lpstat -t
scheduler is running
system default printer: T
device for Alis: /dev/ecpp0
device for T: /dev/lp1
Alis accepting requests since Wed Jan 25 14:27:39 2012
T accepting requests since Wed Jan 25 14:39:03 2012
printer Alis is idle. enabled since Sun Feb 19 11:23:34 2012. available.
printer T is idle. enabled since Sun Feb 19 12:03:31 2012. available.
When is triggered lpstat command After printing
bash-3.2# lpstat -t
scheduler is running
system default printer: T
device for Alis: /dev/ecpp0
device for T: /dev/lp1
Alis accepting requests since Wed Jan 25 14:27:39 2012
T accepting requests since Wed Jan 25 14:39:03 2012
printer Alis is idle. enabled since Sun Feb 19 11:23:34 2012. available.
printer T waiting for auto-retry. available.
Failed to open the printer port. (Device busy)
T-80 [email protected] 201097 Feb 19 12:28 f iltered
T-81 [email protected] 600569 Feb 19 12:28 f
lpq
===
bash-3.2# lpq
T: unknown: moving-to-paused
Rank Owner Job File(s) Total Size
1st appltest 80 /global/u02/oracle/TEST/inst/app201097 bytes
2nd appltest 81 /global/u02/oracle/TEST/inst/app600569 bytes

Hi Freind,
I hope you are doing good.
Q1l:-
Are these printers really physically attached to your Ultra-* parallel port (/dev/ecpp0)?
and what device is "/dev/lp1"?
Answer:-
"/dev/lp1" which is printer "T" and "/dev/ecpp0" which is printer "Alis" are configured at OS level via "printmgr" on the same machine.
This machine hostname is "tprinter" which is a print server. It is connected physically to "CIMA6120 LINE PRINTER".
[what I meant is: what physical port is this printer attached to on the Solaris machine? is this a Ultra 5/10/60 machine? I don't recall the /dev/ecpp port
existing on any modern sun hardware]
"failed to open printer port" can mean:
Answer2:- It's is a 25 pin serial port cable connected to 25 pin parallel port of Optiplex GX100 machine. I installed solaris 10 x86 to make print server. as our CIMA6120 its not a network printer, and our company want to print reports from oracle application to this printer.
Q:-you have attached your printer to the wrong port?
Answer: it is connected to the correct port.
[again . . how do you know this or test this?]
Answer2:- it is connected at the rare panel of the machine on a 25-hole connector (bidirectional).
Q:-you have attached your printer to the right port, but are using the wrong name?
Answer: I think we could have Alias, not necessarily give the same printer name.
[what i was getting at here is that you think the printer is attached to the parallel port, but actually the cable
is actually attached to the wrong port. For example the serial port on those older machines will fit but in that case, if you configure the printer with ecpp
it's not pointing to the correct port]
Answer2:- I configured CIMA6120 with "/dev/lp1" port which was perfectly working, I print numerous pages with this configuration, Suddenly this error "moving-to-paused" occurred. as i said it is connected to the parallel port at the rare panel. Initially, I attempted and tried to configure this printer with "/dev/ecpp0" port which was not successful.
Q:-you have a bad or wrong cable?
Answer:- I have checked the cable it is good.
[how did you do the checking?]
Answer2:- I tested the cable by connecting to other printer and it printed. so no problem with the cable.
In the olden days when local printers like this was the norm, we'd do test like catting a file to the port and see if the printer lights
up or responds. Something like: cat /etc/hosts > /dev/ecpp0 (or /dev/lp1, or whatever the device is). Then observe if the printer seems to
receives anything, blinks, prints the host file. You are copying the file directly to the port outside of lp or other mechanism.
Answer2:- I agree there was some conflict among the ports internally, or some process may be running at the background, that is why though it shows the request waiting in the queue it was moving to pause for some reason. when I check the error by command "lpstat -t" it sez "device busy" in /dev/lp1" file.
Solution
============
After goggling some more I found a fix for this issue at http://fixunix.com/solaris/143011-unaccepted-printer.html
1, I tried to remove the printer from printmgr, cud not remove it.
2, try kill the entries that going to /dev/lp1 port to printer "T". could not do it
3, uncheck the default printer option via printmgr.
4, Add a new printer name "test" with /dev/ecpp0" and reproduce the issue "got the same error"
5, With the forum above it sez its a "bug" and the Bug ID: 6374608. here are the details of it:-
Synopsis: No /devices entry for line printer
http://bugs.opensolaris.org/bugdatab...bug_id=6374608
Workaround is to manually install the missing driver binding
entry, using the command:
update_drv -a -i '"lp"' ecpp
This workaround should create the missing /dev/lp* devices. And after
running it, you should find the following line in "prtconf -D" output:
lp, instance #0 (driver name: ecpp)
6, I unplug the serial cable from the printer and turnoff and replug the serial cable to the printer and turn on the printer, made sure printer is ""ONLINE".
7, I restart the Solaris machine and delete the newly created "Test" printer via printmgr.
7, I just gave the lp /etc/passwd and it printed.
Finally, I thank you for your time and suggest me your opinion on this solution please.
Regards,
MKY
Edited by: user9007339 on Feb 22, 2012 12:15 AM
Edited by: user9007339 on Feb 22, 2012 12:21 AM

I cannot print, get error 'An unknown error occurred while printing."

I can see that hundreds of other people also have this problem and I can't understand why Mozilla don't fix it.
When I go to print an email or a receipt, whether by printer or by PDF, I *sometimes* get the error, 'An unknown error occurred while printing.'
It is very frustrating as the problem is intermittent. Sometimes it works, sometimes it doesn't... even with the same page being printed. Incidentally, that page can be printed in both Chrome and Internet Explorer without a problem.
I have tried other "solutions" in similar, now closed, threads. However, 'reset' is not working for me. Closing Firefox and reopening doesn't work either. I have the latest version of Firefox: 14.0.1 and have Windows x64. There is enough available space in the cache...
I'm just at my wits end with this.

With the latest updates FF 19 BETA and Acrobat X. The new one with the black PDF screen), I'm having difficulty too printing to Adobe PDF. System Win 7 x 64.
Printing to physical printers not an issue.
No errors, but (Not Responding either in FF or Acrobat.) Printing to the PDF printer directly sometimes works. Using the work-around fast enough, it seems to always work.
I found a work-around:
Goto Print Preview
Select Print
Type in your file name
IMMEDIATELY press OK and Minimize Firefox.
All of the progress boxes/windows are getting confused otherwise. With FF opened as a normal page, there are too many different progress boxes.
Acrobat has one, the windows print driver has one, FF seems to have one and they all can't be on top.
They will if FF is minimized.
Incidentally if FF is killed, the "Creating Adobe PDF" shows its face from being hidden.
I did reset Firefox.
This is seriously messed up now. It used to work fine until the last round of updates from M$, Adobe and FF.

HT201210 error shows unknown _1

Similar Messages

Maybe you are looking for